“This site contains affiliate links for which OEMDTC may be compensated” |
NHTSA ID Number: 10160211
Manufacturer Communication Number: 07-150-19
Summary
This bulletin provides a procedure for replacing the rear combination lamp wiring harness. The harness is now available as a service part separate from the lamp assembly.
4 Affected Products
Vehicle
MAKE | MODEL | YEAR |
SUBARU | WRX | 2015-2018 |
INTRODUCTION:
This bulletin provides a procedure for replacing the rear combination lamp wiring harness. The harness is now available as a service part separate from the lamp assembly.
PART INFORMATION:
The wiring harness part number is: 84981VA140.
REMINDERS:
- Always order the most up-to-date replacement parts based on the specific VIN being repaired.
- The packing (gasket) between the lamp assembly and the rear body panel is a one-time use item and MUST be replaced whenever the lamp assembly is removed.
SERVICE PROCEDURE / INFORMATION:
REMINDER: Customer satisfaction and retention starts with performing quality repairs.
Although the procedure for replacing the combination lamp wiring harness is new, the Service Manual procedure for removing and installing the complete lamp assemblies is unchanged. The existing Service Manual procedures contain information critical to performing an effective repair the first time and every time. This includes but is not limited to: important SAFETY precautions, proper inspection criteria, necessary special tools, required processes and related one-time-use parts needed for a complete and lasting repair.
IMPORTANT: Before the harness can be removed from the lamp housing, a portion of the connector lock must be CAREFULLY trimmed away. Use a good, sharp wire cutter as shown below while being careful to not damage the tab portion of the housing the connector slides and locks back onto.
- Install the new harness onto the housing and re-assemble in reverse order of removal. REMINDER: Don’t forget to reinstall the foam block (packing) and always use a new lamp to body gasket.
- Confirm all the functions of the combination lamp operate normally to complete the procedure.
SEOCONTENT-START
Bulletin Number: 07-150-19; Date: 04/17/19 Page 1 of 3
Continued…
NUMBER: 07-150-19
DATE: 04/17/19
APPLICABILITY: 2015-18MY WRX
SUBJECT: Rear Combination Lamp Harness
Replacement Procedure
CAUTION: VEHICLE SERVICING PERFORMED BY UNTRAINED PERSONS COULD
RESULT IN SERIOUS INJURY TO THOSE PERSONS OR TO OTHERS.
Subaru Service Bulletins are intended for use by professional technicians ONLY. They
are written to inform those technicians of conditions that may occur in some vehicles,
or to provide information that could assist in the proper servicing of the vehicle. Properly
trained technicians have the equipment, tools, safety instructions, and know-how to
do the job correctly and safely. If a condition is described, DO NOT assume that this
Service Bulletin applies to your vehicle, or that your vehicle will have that condition.
Subaru of America, Inc. is
ISO 14001 Compliant
ISO 14001 is the international standard for
excellence in Environmental Management
Systems. Please recycle or dispose of
automotive products in a manner that is friendly
to our environment and in accordance with all
local, state and federal laws and regulations.
INTRODUCTION:
This bulletin provides a procedure for replacing the
rear combination lamp wiring harness. The harness is
now available as a service part separate from the lamp
assembly.
PART INFORMATION:
The wiring harness part number is: 84981VA140.
REMINDERS:
• Always order the most up-to-date replacement parts based on the specific VIN being
repaired.
• The packing (gasket) between the lamp assembly and the rear body panel is a one-time use
item and MUST be replaced whenever the lamp assembly is removed.
SERVICE PROCEDURE / INFORMATION:
REMINDER: Customer satisfaction and retention starts with performing quality repairs.
Although the procedure for replacing the combination lamp wiring harness is new, the Service
Manual procedure for removing and installing the complete lamp assemblies is unchanged. The
existing Service Manual procedures contain information critical to performing an effective repair the
first time and every time. This includes but is not limited to: important SAFETY precautions, proper
inspection criteria, necessary special tools, required processes and related one-time-use parts needed
for a complete and lasting repair.
SERVICE BULLETIN
ATTENTION:
GENERAL MANAGER q
PARTS MANAGER q
CLAIMS PERSONNEL q
SERVICE MANAGER q
IMPORTANT – All
Service Personnel
Should Read and
Initial in the boxes
provided, right.
©2019 Subaru of America, Inc. All rights reserved.
Bulletin Number: 07-150-19; Date: 04/17/19 Page 2 of 3
Continued…
• Remove the affected lamp assembly following the
procedure in the applicable Service Manual.
• Remove the gasket to access the harness and the
foam block (packing) shown in the photo.
• Disconnect the LED harness connector then remove the
bulb socket assemblies. Transfer the bulbs over to the new
harness.
LED Harness
Connector
IMPORTANT: Before the harness can be removed from the lamp housing, a portion of the
connector lock must be CAREFULLY trimmed away. Use a good, sharp wire cutter as shown below
while being careful to not damage the tab portion of the housing the connector slides and locks back
onto.
• Install the new harness onto the housing and re-assemble in reverse order of removal.
REMINDER: Don’t forget to reinstall the foam block (packing) and always use a new lamp
to body gasket.
• Confirm all the functions of the combination lamp operate normally to complete the
procedure.
Packing
Bulletin Number: 07-150-19; Date: 04/17/19 Page 3 of 3
WARRANTY / CLAIM INFORMATION:
For vehicles within the Basic New Car Limited Warranty period or covered by an active Subaru
Added Security Classic or Gold plan, this repair may be submitted using the following claim
information:
Labor Description Labor Operation # Fail
Code
Labor
Time
REAR COMBINATION LAMP HARNESS, RIGHT SIDE R&R
B838-753
UWC-43 0.3
REAR COMBINATION LAMP HARNESS, LEFT SIDE R&R UWD-43 0.3
REAR COMBINATION LAMP HARNESSES, BOTH SIDES R&R B838-754 UWE-43 0.5
REAR COMBINATION LAMP TESTING & DIAGNOSIS C838-001 ** 0.5
** When claiming C838-001 for testing, use the Fail Code for the lamp being repaired.
IMPORTANT REMINDERS:
• SOA strongly discourages the printing and/or local storage of service information as
previously released information and electronic publications may be updated at any time.
• Always check for any open recalls or campaigns anytime a vehicle is in for servicing.
• Always refer to STIS for the latest service information before performing any repairs.
NUMBER: 07-150-19
DATE: 04/17/19
https://www.nhtsa.gov/recalls?nhtsaId=10160211
https://static.nhtsa.gov/odi/tsbs/2019/MC-10160211-9999.pdf
“This site contains affiliate links for which OEMDTC may be compensated” |
- Non-polarity. Can be used for brake lights, tail lights, stop lights, parking light, daytime running light, etc. Some sensitive vehicles will meet canbus issue after installing, load resistors or flasher relay will be required to solve these issues, you can contact us through Amazon Buyer Message to get help and solutions
- Low power and high brightness. 5.5W per 7443 led red bulb. Only 1/4 energy consumption of original 7443 red bulb but 4 times brighter. Built in smart IC driver ensure constant current, no radio interference. Plus instant-on capability with zero warm-up time
- Unique imitated halogen shape design. Resembling halogen bulb shape design and sequencing 54 pieces 4014-SMD LED chips precisely around the light. Delivering 360° high luminous efficiency with full amber light, easier to be noticed and safer to drive
- Small size comparable to OEM 7440 bulbs Non-polarity, applied to US standard and CK sockets. Fits: 992, 7440, 7441, 7443, 7442, 7444, W21W, WY21W, 7440NA, 7440NAK, 7444NA,7444NAK, 7443LL.etc. Amazon filter system may not be 100% accurate or up to date, if you are not sure which bulb model fit your vehicle, please check your vehicle owner manual to confirm or ask a question for help
- Electroplating process housing. Improves oxidation resistance and produces less heat. High-end styling, matching great in the assembly. Ideal replacement for your halogen 7440 red bulbs
- (Set of 2 Bulbs) 54SMD 3014 & 3SMD 3030 high brightness chips per bulb, Working Voltage: 9v-30v.
- Fits: 3056 3057 3057K 3057LL 3155 3157 3157K 3157NA 3157NAK 3157LL 3156NA 3156A 3156 3156K 3357 3357K 3357KNA 3357LL 3457 3457-NA 3457K 3457NAK 3757AK 3757ALL 4057 4057LL 4057K 4114 4114LL 4114K 4157 4157LL 4157K 4157NA 4157NAK 5702A 5702AK 5702AK etc. Easy installation, plug and play.
- Application: Brake Lights, Tail Lights etc. Load resistor or flash relay might be needed to prevent the hyper flash when replacement for Turn Signal Lights.
- Advantage: Compatible for both CK/SRCK and Standard socket, non-polarity design. 300% brighter than original halogen bulb, full Aluminum Housing with Projection lens for Maximum Light output and better heat distribution,built in Constant Current IC for Longer life span & Low Power Consumption.
- Please double check owners manual or original bulb number to confirm before placing an order. Any other problem please feel free to contact us, we are always here to satisfy of you.
- (Set of 2 Bulbs) 54SMD 3014 & 3SMD 3030 high Brightness chips per bulb, Working Voltage: 9v-30v
- Fits: 7440A 7440NA 7440 7440SV 7443NA 7441 7443 7443R 7444 992 WY21W W21/5W W21W etc. Easy installation, plug and play.
- Application: Brake Lights, Tail Lights, Stop Lights, Daytime Running Lights, Fog Lights etc. Load resistor or flash relay might be needed to prevent the hyper flash when replacement for Turn Signal Lights.
- Advantage: Compatible for both CK/SRCK and Standard socket, non-polarity design. 300% brighter than original halogen bulb, full Aluminum Housing with Projection lens for Maximum Light output and better heat distribution, built in Constant Current IC for Longer life span & Low Power Consumption.
- Please double check owners manual or original bulb number to confirm before placing an order. Any other problem please feel free to contact us, we are always here to satisfy of you.
- What you receive: package comes with 10 pieces 3157 miniature bulbs, enough quantity to meet your multi usages, you can share them with your friends or as backup
- Durable to use: our miniature light bulb is made of quality material, can be applied for longer time than most standard bulbs, which can serve you for long time
- Nice design: the filament and gas mixture of the long time bulb have been engineered for withstanding road vibration and provide longer life than traditional bulbs
- Low Maintenance: our mini light bulbs are designed for durability, requires low maintenance, so you needn't to spend much time and effort on repairing these 3157 light bulbs
- Warm Note: the 3157 light bulb can only be applied for specific models, please make sure whether your models fit before purchase
- Resembling halogen bulb shape design and sequencing 54 pieces 4014-SMD LED chips precisely around the 3157 led bulb. Delivering 360° high luminous efficiency with full 6000K white light, see more clearly and safely when reversing
- 5.5W per 3157 bulb. Only 1/4 energy consumption of original bulb but 4 times brighter. Built in smart IC driver ensure constant current, no radio interference. Plus instant-on capability with zero warm-up time
- Electroplating process housing. Improve oxidation resistance and produce less heat. High-grade shape, matching great in the assembly. Ideal replacement for your halogen bulbs
- Small size comparable to OEM bulbs. Non-polarity, applied to US standard and CK sockets. Can be used for reverse backup bulb, daytime running light bulb, turn signal bulb, side marker light bulb, blinker light bulb, parking lights, tail lights, brake lights, etc. Fits: 3056 3156 3157 3157K 3057A 4057 4157 4114, etc.
- Important Note: These 3157 led bulbs are not fit the reverse lights of 2018-2022 F150. After entering your vehicle data on browser or APP, please confirm whether the light you want to buy is within the applicable lights. Amazon filter system may not be 100% accurate or up to date, if you are not sure which bulb model fit your vehicle, please check your owner manual to confirm or ask a question for help
- Provides illumination for visibility and convenience
- GM-recommended replacement part for your GM vehicle’s original factory component
- Offering the quality, reliability, and durability of GM OE
- Manufactured to GM OE specification for fit, form, and function
- (Set of 2 W2.5x16q D.F. wedge base 3156/3157 red LED bulbs) LED Chips: Each 3156/3157 LED red bulb is equipped with 39 pieces high quality, high power with high performance led chips per 3156 3157 LED bulb, 360° full angle illumination with projector lens design
- Important: Extra LED resistors maybe required to avoid the signal hyper flash or error code for LED bulbs draw less current than stock lamps. Compatible with both standard and CK / SRCK type. Voltage: 12V~14.8V, Built in stable current IC driver for longer lifespan. Color: Pure red.
- Dual filament LEDs are universal fit for single filament and dual filaments T25 wedge base bulbs. Non-polarity. Cross reference number: 3156, 3056, 3047, 3047LL, 3047K, 3055, 3057, 3057ST, 3057K, 3057KX, 3057X, 3057KLCP, 3057LL, 3155, 3155LL, 3157 ,3157K, 3157X, 3157LL, 3157ST, 3157KX, 3357, 3357LL, 3357K, 3457, 3457K, 4057, 4057LL, 4057K, 4114, 4114LL, 4114K, 4157, 4157LL, 4157K, 4157NA, p27/7w, 3157/40610, 3157/17172, 12450004, 78633, 17945, 3156/21863, 9442003, 78625, 17941, etc.
- Application: Used for upgrading OEM dim incandescent or damaged rear turn signals, directional blinker lamps, brake stop tail lights, taillights, rear side marker light amp for much safer driving and luxury looking for automotive cars, trucks, motorcycles, SUVs, vans.
- Newly upgraded smart IC driver for better performance and longer lifespan. USA located.
- LIGHTS DIM OVER TIME, REPLACE IN PAIRS: Your lights are a pair, one is never turned on without the other. If one bulb burns out, the other isn't far behind.
- EASY TO REPLACE: Sylvania Long Life miniature bulbs are easy to install and show instant results.
- LOW MAINTENANCE AND HIGH DURABILITY: Designed for durability, greater safety, and lower maintenance by the leading supplier of automotive lighting.
- LONGER LIFE THAN MOST STANDARD BULBS: Long Life bulbs perform twice as long as any other standard miniature bulbs.
- THE SYLVANIA STANDARD OF QUALITY: With 100+ years in business, Sylvania is the world leader in automotive lighting for Original Equipment Manufacturers (OEMs) and the aftermarket.
Last update on 2024-03-24 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.