“This site contains affiliate links for which OEMDTC may be compensated” |
NHTSA ID Number: 10144880
Manufacturer Communication Number: 12-249-18
Summary
This Service Information bulletin advises of a design change made to the rear body panel. This panel is located between the trunk and the rear glass and incorporates the package shelf. It has been re-designed with convex surfaces added to prevent items going into or out of the trunk from being scratched or caught by the rear edges of the reinforcement panels.
3 Affected Products
Vehicle
MAKE | MODEL | YEAR |
SUBARU | LEGACY | 2015-2017 |
INTRODUCTION:
This Service Information bulletin advises of a design change made to the rear body panel. This panel is located between the trunk and the rear glass and incorporates the package shelf. It has been re-designed with 2 convex surfaces added to prevent items going into or out of the trunk from being scratched or caught by the rear edges of the reinforcement panels (shown in red) on the illustrations below.
View from inside trunk area looking upward toward underside of package shelf.
PRODUCTION CHANGE INFORMATION:
This new body panel was put into production during mid-April, 2017. The starting VIN will be added to this bulletin when it becomes available.
PART INFORMATION:
The new part numbers for the “PANEL COMPLETE R” are 53105AL02C9P and 53105AL03C9P.
Always order the most up-to-date part as specified by the VIN.
SERVICE PROCEDURE / INFORMATION:
REMINDER: Customer satisfaction and retention starts with performing quality repairs.
The service procedures for replacement of the panel remain unchanged. Always refer to the applicable Body Repair Manual and Service Manual to review the full requirements of the repair being performed before proceeding. The Manual procedures contain information critical to performing an effective repair the first time and every time. This includes but is not limited to:
important SAFETY precautions, proper inspection criteria, necessary special tools, required processes and related one-time-use parts needed for a complete and lasting repair.
SEOCONTENT-START
APPLICABILITY: 2015-2017MY Legacy
SUBJECT: Rear Body Panel- Design Change
IMPORTANT REMINDERS:
- SOA strongly discourages the printing and/or local storage of service information as previously released information and electronic publications may be updated at any time.
- Always check for any open recalls or campaigns anytime a vehicle is in for servicing.
- Always refer to STIS for the latest service information before performing any repairs.
SEOCONTENT-END
NUMBER: 12-249-18
DATE: 08-15-18
https://www.nhtsa.gov/recalls?nhtsaId=10144880
https://static.nhtsa.gov/odi/tsbs/2018/MC-10144880-9999.pdf
“This site contains affiliate links for which OEMDTC may be compensated” |
- 40pcs 90914-0007 Bumper, Engine Cover, Fender & Grille Push-Type Retainer for Subaru Baja, Forester, Impreza, Legacy, Outback & Tribeca 2011 - 2000
- 30pcs 90913-0067 Engine Cover and Fender Liner for Subaru B9, Forester, Legacy, Outback & Tribeca 2005 -
- 30pcs 90914-0051 Front Bumper & Quarter Panel Push-Type Retainer for Subaru Impreza, Legacy, Outback & Tribeca 2011 - 2005
- FITS VARIOUS SUBARU MODELS - The clips fit selected Subaru as well some other car brands.
- Premium OEM Upgraded Quality and Durable —Made of Premium Auto Grade Nylon:PA66(Not Ordinary Cheap Nylon),solid like metal.
- Replacement Clips for Subaru: 3 sizes(7mm, 8mm, 10mm) are suitable for fender, bumper, splash shield and grille clips. See description for manufacturer part numbers.
- Most Cost-effective: Saving you time and money to REPLACEMENT for damaged retainer clips and lost ones.
- Sturdy and Durable: Made of high-quality black nylon material, anti-wear and anti-corrosion, would not break or crack easily during use.
- Tough Fastener Remover: Quickly and easily remove car door panel and upholstery clips without causing damage to them. The ergonomic strong handle allows safe removal of metal or plastic clips.
- Fitment: This push clip is suitable for most Subaru WRX, Forester, Impreza, Tribeca etc. (See full list in the product description below).
Replacement for Subaru Clips OEM NO.: 909140007 (90914-0007)—Fender Liner / Engine Cover / Wheel well Clips
—23/64"(10mm)Hole, Head Dia:13/16"(21mm);Stem Lgt:9/16"(15mm)--20PCSReplacement for Subaru Fasteners OEM NO.:909130067 (90913-0067)—Bumper / Fender Liner / Mud flap / Engine cover / Grill Clips
—5/16"(8mm) Hole, Head Dia:11/16"(18mm);Stem Lgt:3/8"(10mm)--15PCSReplacement for Subaru Rivets OEM NO.: 909140051(90914-0051)—Front Bumper / Quarter Trim Panel / Cowl Trim Panel / Splash Shield / Headlamp Assy Clips
—1/4"Hole(7mm),Head Dia:13/16"(20mm);Stem Lgt:3/8"(9mm)--15PCS- Replacement for Subaru Clips OEM NO.: 91486KJ010 (91486-KJ010)—Cowl Panel Vent Cap Clips —0.17"(4.4mm)Hole, Head Dia:0.72"(18.2mm);Stem Length:0.54"(13.7mm)--15PCS. Replacement for Subaru Clips OEM NO.: 909140063 (90914-0063)—Cowl Vent Air Inlet Duct Push-Type Retainer Clips —0.27"(6.8mm)Hole, Head Dia:0.78"(19.9mm);Stem Length:0.52"(13.2mm)--15PCS
- Premium OEM Upgraded Quality and Stable Subaru Clips Set —Made of Premium Auto Grade Nylon:PA66(Not Ordinary Cheap Nylon),solid like metal. Stable Fasteners & Fastener Remover with Conveniently Organized Box —15*4.4mm hole clips+15*6.8mm hole clips+15*8mm hole clips+20*10mm hole clips+15*7mm hole clips+1*Fastener Remover
- 🔧 Multiple Solutions- Includes 19 Sizes of Subaru Body Interior and Exterior Retainer Fastener Clip, Total 190 Pieces. These Are Reliable Replacement for the Original Part That had Missing or Failed Due to Fatigue.
- ✅ Durable Construction - These Clips are Made from Quality Nylon Materials to Ensure Reliable Performance and Long Service Life.
- 🚗 Fits Most Subaru Models, Including Hood Insulation Retainer, Front & Rear Bumper Push-Type Retainer, Front Fender, Bumper & Quarter Panel Push-Type Retainer, Front Fender Liner, Engine Cover, Hood & Quarter Panel Push-Type Retainer, Nylon Nut, Fender Liner, Duct & Lower Moulding Push-Type Retainer, Garnish Moulding Retainer, Cowl Vent Push-Type Retainer, Trim Board Retainer, Engine Cover and Fender Liner Retainer, Screw Grommet with Sealer, Cowl Panel Vent Cap.
- ✉ Part Number: Subaru 🔷 1 #OE: 909140059; 🔷 2 #OE: 909130013; 🔷 3 #OE: 46064AE000; 🔷 4 #OE: 59130AA000; 🔷 5 #OE: 909140065; 🔷 6 #OE: 661179000; 🔷 7 #OE: 909140068; 🔷 8 #OE: 909130051; 🔷 9 #OE: 909130146; 🔷 10 #OE: 909140063; 🔷 11 #OE: 909130115; 🔷 12 #OE: 909130067; 🔷 13 #OE: 909130074; 🔷 14 #OE: 91084AA010; 🔷 15 #OE: 909140055; 🔷 16 #OE: 91486KJ010, 91486-FL020; 🔷 17 #OE: 57728AC090; 🔷 18 #OE: 909140007.
- ☺ Please Check the Part Number and Installation Position Information on the Picture Before Purchase.
- 30-PCS Front Bumper, Engine Cover, Fender Splash Shield, Quarter Trim Panel, Cowl Trim Panel, Cowl Grille Clip, Headlamp Assembly Retainer, Protector Retainer For Subaru BRZ Tribeca Legacy Outback. OEM Number: for Subaru 90914-0051
- 30-PCS Engine Cover, Phillips Drive Fender Liner Clip, Under Cover Clip, Handle, Inside Clip, Floor Pan Splash Shield Clip For Subaru Crosstrek Forester Legacy Outback XV Crosstrek B9 Tribeca. OEM Number: for Subaru 90913-0067
- 40-PCS Bumper Engine Cover Fender, Grille Clip, Side Cover Clip, Reflector Clip, Reinforced Beam Clip, Splash Pan Clip, Deflector Retainer For Subaru Crosstrek Forester Impreza Ascent BRZ WRX STI. OEM Number: for Subaru 90914-0007
- High Quality - Our clips are made of premium black nylon material, ensuring excellent durability and resistance to breakage. They feature a push-in design for fast and secure fastening. Completely meet your daily use needs. Each size is packed in a separate pouch.
- Practical Function - The push-type fastener clips play an important role in replacing and securing car accessories like engine covers, bumper, fender, cowl trim panel, and wheel well, The fastener can effectively enhance your work efficiency and provide better safety for vehicles.
- 18 MOST COMMON SIZE: GOOACC push retainer Clips are suitable for Mercedes Benz, BMW, TOYOTA, Honda, Subaru, NISSAN, Mazda, Lancer for exact replacement.Not Only for the cars we mention, if the sizes and shape meet your requirement, it also works well
- WIDELY APPLICATION:Theses push clips are widely used for car body clips, trim panel retainer, door trim fastener, door panel clips, bumper clips, Fender clips, engine cover and splash shield retainers replacement. It always covers some applications include telecom equipment, motor vehicles, domestic appliances, furniture and electrical equipment.
- BONUS AUTO FASTENER REMOVER - Allow you to quickly and easily remove car door panel trim clips and upholstery clips without causing damage to them. Easy access into confined areas.
- PREMIUM QUALITY RETAINER ASSORTMENT: GOOACC push rivets are made of heavy-duty plastic&nylon, which is strong, robust and vibration resistant, would not break or crack easily.
- NOTE: GOOACC offers clear pictures for your reference, please check the size, type and shape to make sure the item is the one that you need.If you there is any issue after sale such as inappropriate size& shape, please email us directly, we will offer 100% satisfactory service.
- 【18 Most Popular Sizes】390Pcs auto push retainer Clips,Includes 18 Sizes of Subaru Body Interior and Exterior Retainer Fastener Clip, These Are Reliable Replacement for the Original Part That had Missing or Failed Due to Fatigue.This push clip is suitable for most Subaru Forester, BRZ, Impreza, Legacy, Outback, WRX, Baja, Tribeca etc.
- 【High Quality Material】Retainer clips are made of heavy-duty nylon material, anti-wear, vibration resistant, anti-corrosion, would not break or crack easily. Comes with a plastic box for organized storage. Compact size, convenient to store or carry with in your car.Allows to freely DIY your vehicle accessories at anytime you wanted.
- 【Bonus Auto Fastener Remover】Allow you to quickly and easily remove car door panel trim clips and upholstery clips without causing damage to them. Easy access into confined areas.
- 【Applicable Scene】 The Subaru auto push clips are widely used for front fender liner, engine cover, door trim clips, bumper clips,interior accessories and splash shield retainers replacement.All the necessary retainers for exact replacement of old and broken retainer.
- 【Customer Service】Your satisfaction is our no.1 goal. We are focus on the after sale service for a long time, we can provide the 12-month warranty for our customer. If you are not satisfied for any reason at all, pls contact with us, you will get the full refund on the spot. Follow your heart, add to your cart.
- Clips Type: Bumper, Engine Cover, Fender & Grille Push-Type Retainer
- Dimensions: Head Diameter: 21mm, Stem Length: 15mm (Excluding the Pin), Fits into 10mm Hole
- Material: Durable black nylon, easy to install and remove.
- Car Fitment for: 2019 Subaru Ascent, 2003-2006 Subaru Baja, 2013-2019 Subaru BRZ, 2016-2019 Subaru Crosstrek, 2003-2019 Subaru Forester, 2002-2019 Subaru Impreza, 2004-2014 Subaru Impreza STI, 2002-2014 Subaru Impreza WRX, 2000-2019 Subaru Legacy, 2000-2019 Subaru Outback, 2006-2014 Subaru Tribeca, 2015-2019 Subaru WRX, 2015-2019 Subaru WRX STI, 2013-2015 Subaru XV Crosstrek
- Package Includes: 20pcs Push Pins
Last update on 2024-03-26 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.