Subaru Accessory Installation Guide
| Cigarette Lighter Kit
APPLICABILITY: | H6710AL010
Subaru Cigarette Lighter Legacy Outback Crosstrek Forester Ascent H6710AL010 Genuine
|
|
| |
SEOCONTENT-START
1
PRECAUTIONS
• Please refer to the precautions below before you begin work, in order to install the product safely and accurately
Please also refer to the vehicle Service manual.
• This manual shows typical installation procedures on LHD vehicle. Installation will be mirror image for RHD vehicles.
• Always check the latest service manual, and follow it when this Installation Instruction is revised and a difference
occurs between the revised contents and the latest service manual.
EN: CIGARETTE LIGHTER KIT
LEGACY / OUTBACK, IMPREZA, XV / Crosstrek /
Crosstrek HYBRID, ASCENT, FORESTER
PART No.
EN: COMPONENTS
No. Name Qty
Socket ASSY 1
Plug 1
Ring 1
TOOLS NEEDED
H6710AL010
Installation Instruction
1 2 3
ATTENTION
• Please disconnect the battery cable while conducting wiring operations. Failure to do so
may result in electrical shock or injury.
• Please confirm that the electrical components of the vehicle operate normally. Also, please
make an note of data in the memory of the electrical components such as the radio. This
will help avoid problems that may arise when performing the repair check after the installation.
• When tightening bolts or screws, use the proper tools and the proper size, and comply for
the specified torque specified for the part.
Failure to securely tighten the bolt and nut may cause them to loosen and fall off, causing
damage.
• When removing the connector from the vehicle, remember to remove the lock that holds
the main body of the connector, instead of pulling the lead line.
This protects against a lead wire cuts, etc.
06
2
• Please be sure to properly connect the connector and terminal. This helps to avoid a poor
connection.
• When wiring the harness(wiring), clamp the wires together along with the wiring harness
of the vehicle. This protects the harness from becoming entangled or causing strange
sounds.
• When connecting or disconnecting parts or installing or removing the finisher, etc, be careful
not to let the harness be hooked or pulled from the back. This protects against a cut
wire or shorts.
• Be careful not to forcefully pull the wiring harness of the vehicle. This helps prevent the
connector from being disconnected, and the wires from being cut or damaged.
• After installing the wiring, perform an operations check on the newly installed parts before
reassembling. This helps prevent mis-wiring.
LEGACY / OUTBACK
BEFORE BEGINNING INSTALLATION
1. Apply parking brake firmly and shift the selector lever in N range.
2. For models with power seats, move the seats to the furthest forward position before disconnecting
the battery negative cable.
DISCONNECTING THE BATTERY TERMINAL
1. Open the engine hood and disconnect the battery negative cable.
Follow the latest service manual when disconnecting and/or connecting the battery negative cable.
3
(a) (a)
(a)
Before Action (a),
remove 2 phillips screws.
MOUNTING THE CIGARETTE LIGHTER (REPLACING WITH ACCESSORY SOCKET)
1. Removing associated parts
– Upon removal, wrap the screwdriver
with vinyl tape to avoid scratching the
ornament panels.
1
2
4
3
4
5
5
6
7
8
Tightening torque:
6.5 N・m / 4.8 ft-lb
6
9
10
11 12
Remove socket
Remove ring
Install cigarette lighter as set
Install ring set
Re-install the removed parts
7
IMPREZA, XV / Crosstrek / Crosstrek HYBRID
1. BEFORE BEGINNING INSTALLATION
● Apply parking brake firmly and shift the selector lever in N range.
● For models with power seats, move the seats to the furthest forward position before disconnecting the
battery negative cable.
1-1.Disconnecting the battery terminal
(1) Open the engine hood and disconnect the battery negative cable.
Illustration 1
Illustration 2
2. INSTALLING THE CIGARETTE
LIGHTER
(REPLACING WITH ACCESSORY
POWER SOCKET)
2-1. Removal of related parts
(1) Lift up the cup holder and remove the clips
located towards the rear end of the cover
ASSY – front (models with hand brake) (Illustration
1).
(2) Remove the boot – hand brake (models with
hand brake) (Illustration 2).
Follow the latest service manual when disconnecting and/or connecting the battery negative cable.
8
Illustration 3
(3) Remove the selector knob (Illustration 3)
Pull down the boot ASSY (for boot type models)
or the cover grip AT (for blind type models)
vertically along the lever in the direction.
Remove the pin by pulling it forward in the
direction.
Remove grip ASSY.
(4) Remove the shift knob (MT model).
Illustration 5 (6) Remove the cover ASSY – front (models
with hand brake) (Illustration 5).
Illustration 4 (5) Remove the cover ASSY – front (models
with EPB) (Illustration 4).
9
Illustration 6 (7) Pull out the harness connector (models with
EPB) (Illustration 6).
WARNING
For models with keyless entry and push-button
start system, an interior antenna is located in
the inner side of the tray – center LWR. Take
care not to damage the harness when removing
the cover ASSY – front.
Illustration 8 (10) Remove the console box ASSY (models
with EPB) (Illustration 8).
Illustration 7 (8) Pull out the harness connector (models with
hand brake) (Illustration 7).
WARNING
For models with keyless entry and push-button
start system, an interior antenna is located in
the inner side of the tray – center LWR. Take
care not to damage the harness when
removing the cover ASSY – front.
(9) Remove the mat – center tray and tray – center
LWR.
WARNING
The mat may be damaged if you remove the
Mat – center tray first. Make sure to remove
mat – center tray and tray – center LWR
together.
10
Illustration 9 (11) Remove the console box ASSY (models
with hand brake) (Illustration 9).
Illustration 11 (13) Attach a protective tape to the instrument
panel (for models with audio or navigation
system) (Illustration 11).
(14) Remove the grille ASSY – CTR ventilation
(for models with audio or navigation system)
(Illustration 11).
WARNING
In order to avoid the grille ASSY – CTR
ventilation from being damaged, wrap the
remover with protective tape or cloth, and
remove it by pressing the remover against the
side of the instrument panel.
protective tape
Illustration 10 (12) Remove the panel center LWR (Illustration
10).
11
Illustration 12 (15) Remove the panel – center UPR (for models
with audio or navigation system) (Illustration
12).
Illustration 14
(17) Remove the pocket ASSY (manual A/C model) (Illustration 14).
Illustration 13 (16) Remove the audio or navigation system (for
models with audio or navigation system)
(Illustration 13).
12
Illustration 15 (18) Remove the under cover ASSY – passenger
(manual A/C model) (Illustration 15).
Illustration 17 (20) Remove the ornament – panel ASSY passenger
(manual A/C model) (Illustration 17).
Illustration 16 (19) Remove the cover – instrument panel side
RH (manual A/C model) (Illustration 16).
13
Illustration 18 (21) Remove the back panel – pocket (manual
A/C model) (Illustration 18).
Illustration 20 (23) Push the heater control ASSY from behind
and remove it (Illustration 20).
Illustration 19 (22) Disconnect the cable – mode and cable –
temperature (manual A/C model) (Illustration
19).
WARNING
Check the dial position before disconnecting the
cables.
14
Illustration 21 (24) Pull out the USB connector (Illustration 21).
(25) Pull out the 2 polar (white) power connector
from the accessory power socket (Illustration
21).
(27) Using a flat tip screwdriver, press the 2
claws of the holder (black) attached to the
tray – center UPR and remove the accessory
power socket (Illustration 23).
Illustration 23
(26) Remove the tray – center UPR (Illustration
22). Illustration 22
15
2-2. Installation of related parts
(1) Install socket along the groove of the holder attached to the tray – center UPR. Make sure that
the holder and the hole of socket are fitted firmly (Illustration 24).
(2) Confirm the fitting of socket , and insert the cigarette lighter into socket .
(3) Firmly connect the power connector (2 polar) to the terminal of the accessory power socket.
(4) Connect the USB connector.
(5) Install the related parts in the reverse order of removal.
Illustration 24
socket
cigarette lighter
holder
socket terminal power connector
2 polar (white)
groove
2-3. Operation check
(1) Connect the battery and shift the selector lever in the P range. Turn the ignition/starter switch to the
ACC position, and check that the cigarette lighter operates normally.
(2) Check the operation of the other removed parts. Set the clock and settings for audio system, etc.
and complete the procedure by cleaning the vehicle.
16
ASCENT
MOUNTING THE CIGARETTE LIGHTER (REPLACING WITH ACCESSORY SOCKET)
1. Removing associated parts
– Upon removal, wrap the screwdriver with vinyl tape to avoid scratching the ornament panels.
BEFORE BEGINNING INSTALLATION
1. Apply parking brake firmly and shift the selector lever in N range.
2. For models with power seats, move the seats to the furthest forward position before disconnecting
the battery negative cable.
DISCONNECTING THE BATTERY TERMINAL
1. Open the engine hood and disconnect the battery negative cable.
Follow the latest service manual when disconnecting and/or connecting the battery negative cable.
17
1
C62(W)
Carefully remove vent trim on each side of the radio. Use a trim tool to remove, starting at the
bottom section as shown.
Follow the vehicle service manual for complete removal instruction.
18
2
3
x4
C62(W)
Tightening torque:
1.8 Nm / 1.3 ft-lb
19
4
5
Pawl
Pawl
Align
Install cigarette lighter as shown
• Re-install the removed parts
• Reconnect the battery
• Shift the selector lever into P from N
20
FORESTER
1
(a)
C63(L)
2
(a)
MOUNTING THE CIGARETTE LIGHTER (REPLACING WITH ACCESSORY SOCKET)
1. Removing associated parts
– Upon removal, wrap the screwdriver with vinyl tape to avoid scratching the ornament panels.
BEFORE BEGINNING INSTALLATION
1. Apply parking brake firmly and shift the selector lever in N range.
2. For models with power seats, move the seats to the furthest forward position before disconnecting
the battery negative cable.
DISCONNECTING THE BATTERY TERMINAL
1. Open the engine hood and disconnect the battery negative cable.
Follow the latest service manual when disconnecting and/or connecting the battery negative cable.
21
3
4
5
C63(L)
22
6
7
C63(L)
C62(W)
x2
x2
C63(L)
8
C63(L)
23
9
10
Install cigarette lighter as shown
Align
• Re-install the removed parts
• Reconnect the battery
• Shift the selector lever into P from N
24
Content of revision
Content Date
01
02 Added procedure for Impreza 10/2016
03 Added procedure for ASCENT 1/2018
04 Added procedure for FORESTER 7/2018
05 Added warning of Gasoline engine model/ HEV model 9/2018
06
Changed operation procedure for disconnecting and/or connecting
battery terminal 11/2018
SEOCONTENT-END
H6710AL010
- Safety Protection: Built-in with a 20A fuse to prevent overcurrent and short circuit, and equipped with 25A and 30A spare fuses, this 12 volt cigarette lighter socket meets the voltage requirements of different devices, reduces voltage loss, and ensures the safety of use
- Waterproof & Dustproof: Equipped with a waterproof and dustproof cover, this 12v outlet socket effectively prevents dust, snow, and water from entering, keeps the device clean and dry, and avoids rusting, extending its service life even in harsh environments and ensuring the equipment is always in good condition
- Heavy Duty Wire: Made of pure copper wire with excellent conductivity, high temperature resistance, and corrosion resistance, this 12v outlet ensures efficient power transmission and long-term durability. The cable specification is SPT-2 12AWG/2C (3.31mm²), with a length of 10 feet (3 meters), suitable for 12V/24V input and output voltage
- Easy Installation Design: Threaded to securely hold in the desired position and not easily loosened, this 12v socket features pure copper O-type terminals with an 8.4 mm (0.33 inch) inner diameter, which are easy to install. The red cable connects to the positive terminal and the black cable connects to the negative terminal to ensure safe use
- Widely Used: Suitable for many kinds of vehicles such as cars, motorcycles, boats, etc., this 12v socket power outlet can provide a stable power supply for high-power devices like air pumps, inverters, car refrigerators, water heaters, and rice cookers, meeting your power needs in different scenarios
- 🩹【Stylish Design】 Want to give your car cigarette lighter a whole new look? Want to stop letting it just for collecting dust? We use the bright car cigarette lighter socket with a circle of metal chrome decoration, the metallic texture will never go out of style, I guarantee he will be an attractive car decoration in your car interior and bring convenience to your life.
- 🩹【Universal Car Power Socket】 This unique 12V cigarette lighter socket is suitable for use with most cars, boats, ships, motorcycles, ATVs, RVs, trucks, golf carts, etc. You can use it to power your MP3, GPS, cell phone, camera, cigarette lighter shunt, car vacuum cleaner and other electronic devices, replacing your broken or boring cigarette lighter.
- 🩹【Multifunction Car Cigarette Lighter Adapter】 The kit also contains a cigarette lighter plug that can be used for lighting cigarettes! Ideal for car owners who like to smoke in car, built with a hollow heat dissipating ceramic core and stainless steel. Plug in the cigarette lighter, heated for about 30 sec, its button automatically pops out can be used, so that the uninformed amazed.
- 🩹【Reliable Construction】 One of the safest car lighter plugs with built-in 10A fuse and multiple protection system with over-current, overheat and short-circuit protection, providing safety protection regarding temperature. The cigarette lighter plugs can also be waterproof and dustproof, effectively protecting the internal circuit and prolonging the service life.
- 🩹【Easy to Install】 Convenient for daily use. Each socket has a fastening nut against the panel. The kit also contains 2Ft/23.7inch long leads, color coded positive and negative, you only need to have a 1.2 inch diameter hole to install, no need to prepare other tools. (May require you to learn something about how to wire.)
- High Quality: The cigarette lighter plug shell is resistant to high temperature and corrosion, and 16 AWG pure copper wire, which greatly improves the conductivity
- Good Safety: Cigarette lighter plug adapter built-in 15A fuse for overload protection
- Wide Applications: This lighter plug adapter can be used to power CB radios, car vacuum cleaners, tire air pumps, car inverters, electric cooler, car washers, etc
- Easy to Use: The lighter plug adapter red wire is positive and the black wire is negative. Almost all models of cigarette lighter sockets are applicable. When the line is connected, the LED light will light up to avoid multiple operations
- Complete Accessories: The cigarette lighter plug package has 8 built-in 10A fuse tubes, 8 wiring terminals, and 4 protective covers
- 【STABLE CONNECTION】 The cigarette lighter socket has an inner diameter of 21mm, a standard size that allows it to hold most plugs securely and provide a stable connection. 12v cigarette lighter socket is equipped with a 2.5mm²/13AWG solid copper cable that supports 20A current, a cable length of 10FT, and solid copper eyelets at the end of the cable. The inner diameter of the terminal is 8.4mm.
- 【HIGH QUALITY 12V OUTLET】 12v power outlet is made of pure copper cable and brass socket with good conductivity, the cable is made of thickened insulated high temperature resistant pvc material with long service life. 12v socket and cable are injection molded and won't come loose. 12v outlet socket is threaded on the outside with a diameter of 28.5mm at the threads.
- 【SAFETY PROTECTION】 The 12 volt cigarette lighter socket has a built-in 20A fuse in the fuse holder, which can well protect the car battery and prevent high current or short circuit from damaging your device. The 12v power supply car plug outlet also comes with 2 extra spare fuses (20A, 25A).
- 【WATERPROOF AND DUSTPROOF】 12 volt power supply cigarette lighter plug comes with a rubber cap, the rubber cap can be opened or closed quickly, you can cover the rubber cap to prevent dust and water from entering the inside of the 12 volt power outlet when you don't use the car cigarette lighter socket.
- 【WIDELY USED】 12v socket power outlet is widely used for installing or replacing 12 volt outlets in cars, motorcycles, boats, etc. It can be directly connected to 12v deep cycle batteries, female cigarette lighter socket is suitable for high power devices, such as air pumps, inverters, car refrigerators, water heaters, vacuum cleaners, coffee maker, rice cooker, etc.
- 【12V/24V 3.1A Dual Socket】The 12V Cigarette Lighter Socket is design with 2 female sockets, which can be used at the same time, the total output of the two ports is 3.1A, the output power is 120W, the voltage is DC 12V-24V, suitable for 12-24V vehicle power supply equipment, such as GPS, Dash Cam, Vacuum Cleaner, Car Fridge, Heated Seats, and Sat Nav, ect.
- 【DURABLE PLASTIC & METAL CORE】The housing of this 12V motorcycle power outlet is made of durable plastic, which has high current resistance, high temperature resistance and abrasion resistance. Besides the dual cigarette lighter socket are made of all metal inner core, so solid and strong. The solid construction makes the 12v motorcycle cigarette lighter last a long time.
- 【15A BLADE FUSE & DUSTPROOF WATERPROOF COVER】Come with a standard 15A in-line fuse, protect your device from over-voltage, over-heating, over-load, or short-circuit. Equipped with waterproof and dustproof cover, effectively protects the marine power outlet against sudden water splashes and influence of dust, avoid short-circuited and poorly contacted, which effectively prolongs the service life.
- 【14AWG GAUGE PURE COPPER CABLE & EASY TO INSTALL】The Cable of the 12v plug and socket is made of pure copper wire, the Gauge of the cable is 14AWG, which has better conductivity. The long length of 17.5 inches is conveninent for installation. Just connect the RED wire to ''+'' and BLACK wire to "-".
- 【WIDE USES & PACKAGE INCLUDES】The 12 volt outlet socket fits for any vehicles powered by DC 12V/24V, such as car, motorcycle, boat, marine, truck, RV, golf cart, ATV, UTV, Van etc. It's can power the GPS, dashcam, air purifier, car vacuum cleaners, car heater etc, and also be used in conjunction with a car charger to charge your phone. (Package includes: 1* 12V Cigarette Lighter Socket; 2* Mounting Screws)
This product presentation was made with AAWP plugin.