Accessory Installation Guide
| 2019-23+MY Ascent – Cargo Area Lighting Kit | H461SXC200 |
INSTALLATION INSTRUCTIONS
PART NUMBER: H461SXC200
DESCRIPTION: Cargo Area Lighting Kit
KIT CONTENTS:
1. Illuminated Cover Assembly
2. Wire Tie (1) (Inserted into Illuminated Cover Assembly)
PREPARATION – BEFORE INSTALLATION:
1. This product should be installed with proper installation tools.
2. Install this product while observing all warnings and precautions stated in this instruction booklet.
3. Read entire installation guide prior to beginning the installation of the accessory.
4. Ensure vehicle is properly protected from damage during installation.
5. Never place tools or parts on top of painted surfaces, seats, dash pad, console or floor carpet / mat.
6. Always wear appropriate safety gear to include gloves and eye protection when required.
H461SXC200
H461SXC200 (French)
- Trunk Ceiling Lighting for Toyota RAV4 2022 2023 2024 2025
- 1. Remove some of the door gasket at the top of the hatch door frame to get access to the headliner. 2. Gently pull the headliner down slightly. Route the end of the power wire with the two connectors under the headliner, toward the right side of the car, down, and then behind the trim panels to the existing light.
- 3. Back where you started take the other end of that cable and route it through the LEFT rubber tube running between the doorframe and the hatch (the right one supplies water for the rear windshield washer – Leave It Alone). 4. After (NOT Before) that is done insert the two wires into the provided plastic connector making sure that the red and white wires will match up to the red and white wires on the connector that it goes into. Replace the gasket.
- No cutting is necessary for the installation, the lights replace two access panel covers on the inside of the rear hatch. All parts necessary for the installation are included. If you need installation video, kindly contact seller for help. Thank you.
- Bright enough and have enough coverage to fully illuminate the cargo area. The lights turn on automatically when the hatch is raised and turned off when it is closed. They can also be turned off manually with a switch on the face of the lights. One year warranty, any problems, contact seller freely.
- Compatible with a variety of Ford, GMC, Chevy, Dodge, Toyota, Nissan, and Honda pickup trucks
- One pair of universal fit 5-piece set water-resistant xenon white LED truck bed decoration spot beam pattern light kit with double-sided tape or screws for easy mounting of each LED pod
- Each round-shaped LED pod is powered by 9 super bright 5mm projector head LED diodes with IP67 waterproof rating, featuring 24" wiring to connect to another LED pod, totaling 5 pieces in a string with additional 110" long wiring
- You can mount this LED array/strip inside the truck bed under the side edge or under rail to fully illuminate the entire trunk cargo area, or use them as underglow, foot step courtesy lights, running board lights, or rock light kit
- Ideal for pickup truck enthusiasts looking to upgrade their vehicle with bright and efficient LED strip lights that offer a sleek appearance and super bright lighting
- Must have factory cut outs for lights and switch in the bed
- UV Treated Polycarbonate Lens
- IP67-Rated Construction
- Convenient, Plug-and-Play Installation
- No BCM Re-programming Necessary. Does not tie info factory wiring
- For Toyota Sienna 2021 2022 2023 2024 Car Accessories Trunk Ceiling Lighting Hatch Door LED Cargo Dome Lights Lamp Replacement A Kit
- Enhance visibility inside your vehicle, making it easier to find things in low-light conditions. Upgrade the look of your car interior with a modern and stylish lighting setup.
- The light is tailored to seamlessly integrate with the factory design, easy install with plug and play design.
- Bright enough and have enough coverage to fully illuminate the cargo area. The lights turn on automatically when the hatch is raised and turned off when it is closed. They can also be turned off manually with a switch on the face of the light.
- Package including: 2xLED Trunk Ceiling Hatch Light; 2xwiring harness; 1x pry tool
- 【Fitment】Compatible with Tacoma 2020 2021 2022 2023 & newer. Replacement for OEM part number: PT857-35200
- 【Easy to Install】Direct factory replacement, plug and play operation, direct bolt-on installation procedure, no modification, cutting or drilling required.
- 【Excellent Brightness】Built-in high power chip, 15 times brighter than OEM LED bed light. Ultra-bright xenon white light output maximizes illumination around the truck bed. Effectively illuminates your truck bed and provides excellent light distribution during loading and unloading, helping to improve cargo management at night or in dark places.
- 【Sturdy Construction & Durability】Made of extremely durable and lightweight automotive grade ABS plastic. Fully sealed, waterproof, rustproof and shockproof. The hard and durable ABS plastic can effectively protect the bed light from slight impact, and it will not fade after long-term use.
- 【Package Included】This package comes with 2 LED truck bed lights as well as 2 wiring harnesses. If you have any other questions, please feel free to contact us.
SEOCONTENT-START
DESCRIPTION
Illuminated Cover Assembly
ISSUE
01
DATE
02/26/24
PAGE
SUBARU
OF AMERICA 1/3
INSTALLATION INSTRUCTIONS
PART NUMBER: H461SXC200
DESCRIPTION: Cargo Area Lighting Kit
KIT CONTENTS:
1. Illuminated Cover Assembly
2. Wire Tie (1) (Inserted into Illuminated Cover Assembly)
Panel Safe Tool
Denotes quality processes to be checked prior to
moving to the next step.
Denotes specific tools that are necessary to complete
the step.
Denotes cautions to be taken to avoid vehicle and
component damage.
Denotes cautions to be taken to avoid physical
injury or electronic component damage.
Direction
Wire Tie
(Detach and save for
installation at step 5)
Remove
Claw Clip
Disconnect
Connect
MEANING OF CHARACTERS:
This product should be installed with proper installation
tools.
Install this product while observing all warnings and precautions
stated in this instruction booklet.
Read entire installation guide prior to beginning the installation
of the accessory.
Ensure vehicle is properly protected from damage during
installation.
Never place tools or parts on top of painted surfaces, seats,
dash pad, console or floor carpet / mat.
Always wear appropriate safety gear to include gloves and
eye protection when required.
PREPARATION – BEFORE INSTALLATION:
1.
2.
3.
4.
5.
6.
1. 2.
DESCRIPTION
Illuminated Cover Assembly
ISSUE
01
DATE
02/26/24
PAGE
SUBARU OF AMERICA 2/3
1
3
5
2
4
6
Open rear gate before disconnecting battery.
Locate the illuminated cover assembly connector.
Disconnect ground terminal from the battery sensor.
Wait at least 60 seconds before starting work.
Loosen clips and remove trim panel assembly.
Connect harness to illuminated cover assembly.
Bundle excess wire and secure the wire harness
with (1) wire tie.
Install illuminated trim panel cover assembly.
Socket and Ratchet
Panel safe tool
Shock hazard present
Wire Tie
Connection
Connector
Connector
Location
DESCRIPTION
Illuminated Cover Assembly
ISSUE
01
DATE
02/26/24
PAGE
SUBARU OF AMERICA 3/3
7 8
Verify Luggage room light is on
Verify upper trim panel is illuminated
If light is off press on-off switch
located on right side of trim piece
Reconnect ground terminal from the battery sensor.
Wait at least 60 seconds before starting vehicle.
Test illuminated trim panel.
Socket and Ratchet
Shock hazard present.
**************************************************************************************************************
LA DESCRIPTION
Assemblage de couvercle éclairé
PUBLIER
01
DATE
02/27/24
PAGE
SUBARU OF AMERICA 1/3
INSTRUCTIONS D’INSTALLATION
NUMÉRO D’ARTICLE: H461SXC200
LA DESCRIPTION:Trousse d’éclairage de l’aire de chargement
CONTENU DU KIT :
1. Assemblage du couvercle éclairé
2. Attache de fil (1) (Pièce insérée dans l’assemblage du couvercle éclairé)
Outil de coffre-fort de panneau
Griffe Agrafe
SIGNIFICATION DES CARACTÈRES :
Ce produit doit être installé avec les outils d’installation
appropriés.
Installez ce produit en respectant tous les avertissements et
précautions indiqués dans ce livret d’instructions.
Lire l’intégralité du guide d’installation avant de commencer
l’installation
de l’accessoire
Assurez-vous que le véhicule est correctement protégé
contre les dommages pendant l’installation.
Ne placez jamais d’outils ou de pièces sur des surfaces
peintes, des sièges, un tableau de bord, une console ou un
tapis de sol.
Portez toujours un équipement de sécurité approprié pour
inclure des gants et une protection oculaire si nécessaire.
PRÉPARATION – AVANT L’INSTALLATION :
1.
2.
3.
4.
5.
6.
1. 2.
Attache de fil
(Détachez et enregistrez pour
l’installation à l’étape 5)
Indique les vérifications de qualité à effectuer avant
de passer à la prochaine étape.
Indique les outils nécessaires pour compléter une
étape.
Indique les précautions à prendre pour éviter les
dommages au véhicule et aux composants.
Indique les précautions à prendre pour éviter les
blessures ou les dommages aux composants électroniques.
Direction
Retirer
Déconnecter
Relier
LA DESCRIPTION
Assemblage de couvercle éclairé
PUBLIER
01
DATE
02/27/24
PAGE
SUBARU OF AMERICA 2/3
1
3
5
2
4
6
Ouvrez le hayon avant de débrancher la batterie.
Repérez le connecteur de l’ensemble de couvercle
éclairé derrière le côté supérieur droit du
panneau de garniture.
Débranchez la borne de masse du capteur de
batterie. Attendre au moins 60 secondes avant de
commencer le travail.
Desserrez les clips et retirez l’assemblage du
panneau de garniture.
Connectez le faisceau à l’ensemble de couvercle
éclairé. Regroupez l’excédent de fil et fixez
le faisceau de câbles avec (1) attache-fil.
Installez l’ensemble de couvercle de panneau de
garniture éclairé.
Douille et Cliquet
Outil de coffre-fort de panneau
Risque d’électrocution présent
Emplacement du
Connecteur
Connecteur
Attache de fil
Connexion
LA DESCRIPTION
Assemblage de couvercle éclairé
PUBLIER
01
DATE
02/27/24
PAGE
SUBARU OF AMERICA 3/3
7 8
Vérifiez que la lumière de la salle
des bagages est allumée
Vérifiez que le panneau de garniture
supérieur est éclairé
Si la lumière est éteinte, appuyez sur
l’interrupteur marche-arrêt situé sur
le côté droit de la garniture
Reconnectez la borne de masse du capteur de
batterie. Attendre au moins 60 secondes avant de
démarrer le véhicule.
Testez le panneau de garniture éclairé.
Douille et Cliquet
Risque d’électrocution présent.
**************************************************************************************************************
SEOCONTENT-END
This product presentation was made with AAWP plugin.