Body Side Molding – 2023 Subaru Solterra

SEOCONTENT-START

INSTALLATION INSTRUCTIONS PART NUMBER: PS938-42190-XX DESCRIPTION: BODY SIDE MOLDING KIT DESCRIPTION BODY SIDE MOLDING KIT ISSUE 01 DATE 22/04/04 SUBARU OF AMERICA PAGE 1 / 5 Masking Tape – 1” wide PRE-INSTALLATION NOTES: – Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation. KIT CONTENTS: Body Side Molding Passenger Side FR – 1X Body Side Molding Passenger Side RR – 1X Body Side Molding Driver Side FR – 1X Body Side Molding Driver Side RR – 1X TOOLS REQUIRED: Rubber Roller – 1” to 3” wide Cleaner Flexible Scale or Tape Measure Clean Lint-Free Cloths Non-marring straight edge INSTALLATION INSTRUCTIONS PART NUMBER: PS938-42190-XX DESCRIPTION: BODY SIDE MOLDING KIT DESCRIPTION BODY SIDE MOLDING KIT ISSUE 01 DATE 22/04/04 SUBARU OF AMERICA PAGE 2 / 5 ENSURE VEHICLE IS CLEAN AND ENSURE VEHICLE IS CLEAN AND PREPPED FOR INSTALL.PREPPED FOR INSTALL. WIPE THE CLEANED SURFACE WIPE THE CLEANED SURFACE WITH A DRY LINTWITH A DRY LINT–FREE CLOTHFREE CLOTH.. ENSURE DOOR SURFACE ENSURE DOOR SURFACE TEMPERATURE IS BETWEEN TEMPERATURE IS BETWEEN 60°F 60°F (16°C) TO 90°F (32°C).(16°C) TO 90°F (32°C). SATURATE AND CLEAN SATURATE AND CLEAN AREA USING A LINT FREE AREA USING A LINT FREE CLOTH.CLOTH. LOCATE THE HORIZONTAL MEASUREMENT LOCATION ON THE FRONT CLADDING. 1 2 3 FRONT DOOR MEASURE THE LOCATIONS MEASURE THE LOCATIONS ALONG THE UPPER EDGE OF ALONG THE UPPER EDGE OF THE THE FRONTFRONT CLADDING, THEN CLADDING, THEN MEASURE THE VERTICAL MEASURE THE VERTICAL LOCATIONS FOR THE LOCATIONS FOR THE FRONTFRONT MOLDING.MOLDING. FOR EACH VERTICAL FOR EACH VERTICAL LOCATION, PLACE A PIECE OF LOCATION, PLACE A PIECE OF TAPE ON THE TAPE ON THE FRONTFRONT DOOR.DOOR. INSTALLATION INSTRUCTIONS PART NUMBER: PS938-42190-XX DESCRIPTION: BODY SIDE MOLDING KIT DESCRIPTION BODY SIDE MOLDING KIT ISSUE 01 DATE 22/04/04 SUBARU OF AMERICA PAGE 3 / 5 6 4 REAR DOOR MEASURE THE LOCATIONS ALONG THE MEASURE THE LOCATIONS ALONG THE UPPER EDGE OF THE UPPER EDGE OF THE REARREAR CLADDING, CLADDING, THEN MEASURE THE VERTICAL THEN MEASURE THE VERTICAL LOCATIONS FOR THE LOCATIONS FOR THE REARREAR MOLDING.MOLDING. FOR EACH VERTICAL LOCATION, FOR EACH VERTICAL LOCATION, PLACE A VERTICAL PIECE OF TAPE ON PLACE A VERTICAL PIECE OF TAPE ON THE REAR DOOR.THE REAR DOOR. 5 MEASURE THE DISTANCE FROM THE MEASURE THE DISTANCE FROM THE EDGE OF THE FRONT DOOR TO THE EDGE OF THE FRONT DOOR TO THE EDGE OF THE FRONT MOLDING.EDGE OF THE FRONT MOLDING. USING A PIECE OF TAPE, MARK THE USING A PIECE OF TAPE, MARK THE LOCATION OF THE FRONT MOLDING LOCATION OF THE FRONT MOLDING FROM THE EDGE OF THE FRONT DOOR.FROM THE EDGE OF THE FRONT DOOR. USIN USING A PIECE OF TAPE, MARK THE G A PIECE OF TAPE, MARK THE LOCATION OF THE REAR MOLDING LOCATION OF THE REAR MOLDING FROM THE EDGE OF THE REAR DOOR.FROM THE EDGE OF THE REAR DOOR. MEASURE THE DISTANCE FROM THE MEASURE THE DISTANCE FROM THE EDGE OF THE REAR DOOR TO THE EDGE OF THE REAR DOOR TO THE EDGE OF THE REAR MOLDING.EDGE OF THE REAR MOLDING. HORIZONTAL TAPE STRIP HORIZONTAL TAPE STRIP APPLY A HORIZONTAL STRIP OF TAPE BRIDGING THE FRONT AND REAR DOOR GAP. INSTALLATION INSTRUCTIONS PART NUMBER: PS938-42190-XX DESCRIPTION: BODY SIDE MOLDING KIT DESCRIPTION BODY SIDE MOLDING KIT ISSUE 01 DATE 22/04/04 SUBARU OF AMERICA PAGE 4 / 5 7 FOR EACH MOLDING, CAREFULLY FOLD THE LINER TABS AWAY FROM THE MOLDING SUCH THAT THE TABS ARE ACCESSIBLE WHEN THE MOLDING IS IN INSTALL POSITION. REPEAT FOR THE FRONT MOLDING. PEEL THE PEEL THE LINERLINER 8 CAREFULLY HOLDING THE REAR MOLDING, ALIGN THE MOLDING ON THE MARKED LOCATIONS. BEGIN TO PEEL AWAY THE LINER BEGINNING FROM THE MIDDLE OF THE VEHICLE. REPEAT FOR THE FRONT MOLDING. INSTALLATION INSTRUCTIONS PART NUMBER: PS938-42190-XX DESCRIPTION: BODY SIDE MOLDING KIT DESCRIPTION BODY SIDE MOLDING KIT ISSUE 01 DATE 22/04/04 SUBARU OF AMERICA PAGE 5 / 5 9 CHECK THE ALIGNMENT BETWEEN THE MOLDINGS BY PLACING A NON-MARRING STRAIGHT EDGE FLUSH WITH THE BOTTOM OF THE FRONT AND REAR MOLDINGS. THE EDGES MUST ALIGN. NON NON–MARRINGMARRING STRAIGHT EDGESTRAIGHT EDGE 10 USE A HAND ROLLER TO ROLL OVER THE MOLDINGS WHILE APPLYING 15 LBS OF FORCE TO ENSURE COMPLETE ADHESION OF TAPE TO THE DOOR SURFACE.

SEOCONTENT-END