STI Rear Roof Spoiler – 2024 Subaru Impreza & Crosstrek (excluding Wilderness)

SEOCONTENT-START

△00 ●Ratchet Wrench ●Socket（8 mm,10 mm） ●Extension(100 mm) ●Torque Wrench ●Radio Pliers ●Masking Tape ●Waste Rag ●Scale No. -１- Installation instruction Part Name STI REAR ROOF SPOILER(Assembly part） Quantity 1 NOTES This manual describes how to install STI REAR ROOF SPOILER. 1.Be sure to reflect the installation notes in this manual when installing. If you ignore the notes and install it, the product may come off or fall off, and it may interfere with the vehicle’s functions.2.Turn off the Ignition Switch and apply the Parking Brake before starting the installation work.3.Please note that using thinner or the like on STI REAR ROOF SPOILER may damage the surface. Also, please be aware that if you bring fire close to it, it may deform.4.When handling STI REAR ROOF SPOILER, please be careful not to drop it.5.Refer to the vehicle service manual for vehicle part removal and tightening torque. ① Part No. Ｅ７２１０ＦＮ０１０ Applicable model ＣＲＯＳＳＴＲＥＫ（ＧＵ）Ａ Ｔｙｐｅ～ TOOLS USED Be sure to read this manual before installation to install correctly. COMPLETION DRAWING KIT CONTENTS Sold by SUBARU Co., Ltd STI REAR ROOF SPOILER ！ ① (２).Remove the claws in the center ・Please note that if the pinching force NOTES ２．Remove the High Mounted Stop Lamp the locking claw no longer catches. of the Radio Pliers is too large, (１).Remove the claws on the terminal (2 places) wiring connector.【Figure 2】 Figure 1 Figure 2 and remove the Trim Panel. (2 places on the left and right) １．Open the Rear Gate and remove the Trim Panel. of the Trim Panel. (１).Wrap Masking Tape around the tip (２).Pinch the connector and bend it until the locking claw no longer of Radio Pliers. catches. INSTALLATION PROCEDURE ・Be careful not to hurt your hand with the edge of the sheet metal. to separate. 【Figure 1】 -２- (３).Deconnect the connector when the connector will be difficult of the Trim Panel ！ ！ ・The removed bolts will be used again, so keep them organized so that they will not be lost. not to damage the Spoiler by hitting it against the vehicle body. ・After removing the Spoiler, wipe off the dirt on the removal surface upward (about 45°direction) to remove the clips from the Rear Gate. and Socket(10 mm). (6 places) ４．Close the Rear Gate and remove the inside the Rear Gate. (１).Remove the bolts with Ratchet Wrench from the indoor side.【Figure 3】 NOTES Figure 3 Figure 4 ・When removing the clips, be careful (3 places) NOTES ・Be careful not to pinch your fingers the Rear Gate. (３).Remove the Spoiler from the Rear Gate. -３- ・Be careful not to drop the bolts Spoiler from the Rear Gate.【Figure 4】 with a Waste Rag. ３．Remove the Spoiler installing bolts ・Use Extension(100 mm) to remove bolts. (２).Remove the wiring grommet from side. Pull the Spoiler diagonally when opening and closing the Rear Gate. (１).The clips are fixed on the Spoiler ！ ！ ！ ！ ６．Install the High Mounted Stop Lamp to STI REAR ROOF SPOILER.【Figure 6】 so keep them organized so that Ratchet Wrench and Socket(8 mm). in even on the left and the right. ・Be careful not to crush the High Figure 7 NOTES they will not be lost. when installing. (１).Fit the High Mounted Stop Lamp NOTES the grommet.【Figure 6】【Figure 8】 STI REAR ROOF SPOILER and (４).Securely tighten the nuts with on the guide about 120 mm from Stop Lamp so that the gap between (３).Remove the High Mounted Stop Lamp. in STI REAR ROOF SPOILER. REAR ROOF SPOILER and the vehicle body the High Mounted Stop Lamp (５).Hook the High Mounted Stop Lamp wiring Tightening torque：5.0 Nm and Socket(8 mm). (2 places) (１).Remove the wiring from the guide. Mounted Stop Lamp wiring between STI Ratchet Wrench and Socket(8 mm). ・The removed nuts will be used again, Figure 5 from the removed Spoiler.【Figure 5】 ５．Remove the High Mounted Stop Lamp (２).Remove the nuts with Ratchet Wrench Figure 6 (３).Adjust the position of the High Mounted -４- (２).Temporarilly tighten the nuts with 【Figure 7】 (2 places) (2 places) Figure 8 ！ ！ ！ ！ (１).Install the wiring grommet to the Rear Gate.【Figure 9】 Figure 9 ７．Install STI REAR ROOF SPOILER to NOTES Figure 10 (１).Temporary tighten the bolts with ８．Open the Rear Gate and tighten the bolts the Rear Gate using the clips to the rear gate without any gaps. ・Be careful not to let STI REAR ROOF damage them. ・Make sure the grommet is firmly attached the clips to the Rear Gate. (3 places) from the indoor side.【Figure 10】 NOTES the Rear Gate Panel are shown in the figure.(6 places) Ratchet Wrench and Socket(10 mm). (6 places) (３).Tighten the bolts securely with Torque Wrench(10 mm) in the order Tighten torque：7.5 Nm ・Be careful not to drop the bolts inside the Rear Gate. even on the left and right. -５- (２).Make sure the gaps between the diagonally downward (about 45°direction)to install (３).Push in STI REAR ROOF SPOILER (２).Apply STI REAR ROOF SPOILER to the Rear Gate. terminals on both sides and SPOILER hit the vehicle body and as a reference. ！ ！ ！ ！ (２).Install the claws on the terminal of the Trim Panel. make sure that (１).Install the claws in the center and restore the Trim Panel. REV No. CONTENTS -６- (５).Open and close the Rear Gate and (６).Close the Rear Gate, This is the end of the work. of the Trim Panel to the Rear Gate. DATE securely connected. Figure 11 lightly by hand, and make sure ・After the installation is complete, (2 places on the left and right) the High Mounted Stop Lamp is lit. side connector.【Figure 11】 shake STI REAR ROOF SPOILER ９．Open the Rear Gate (４).Connect the High Mounted Stop Lamp side connector to the vehicle body make sure STI REAR ROOF SPOILER is Figure 12 NOTES there is no backlash. 【Figure 12】 (2 places) ！ ！

**************************************************************************************************************

**************************************************************************************************************

SEOCONTENT-END