NHTSA ID Number: 10233084
Manufacturer Communication Number: 1216013
Summary
Cracked Rear Combination Lamps
NUMBER: 12-160-13
DATE: 12/23/13
| APPLICABILITY: | 2013-14MY BRZ |
| SUBJECT: | Cracked Rear Combination Lamps |
INTRODUCTION
This bulletin announces availability of a revised trunk weatherstrip and rubber stoppers designed to absorb impact and prevent contact or in rare occurrences, damage to the rear combination lamps when closing the trunk lid.
COUNTERMEASURE IN PRODUCTION
The new weatherstrip and rubber trunk stoppers were incorporated into production starting with the following VINs:
| Weatherstrip | E*600523 |
| Rubber Trunk Stoppers | E*601334 |
PART INFORMATION
A liner was added into the weatherstrip for increased resistance to crush and the trunk stopper’s overall height was increased by 2.7mm to minimize the chance of trunk lid contact with the combination lamps.
| PART NAME | PART NUMBER |
| WSTR Trunk | 57532CA001 |
| Stopper Trunk Lower | 57533FE040 |
SERVICE PROCEDURE / INFORMATION
To remove the trunk stopper, use a plastic trim tool to lift up and release one of the retaining tangs. Once you have one side released, hold the one side of the stopper away from the body then release the opposite tang with the plastic trim tool as shown in the photos below.
Release One Tang
Tang Released
Hold Onto Stopper and Release the Opposite Side Tang
Grasp and pull up on the old weatherstrip to release and remove it from the trunk opening body flange. Leave any adhesive remaining on the flange in place to help secure the new weatherstrip.
Start the installation with the seam aligned with the striker, arrow and notch towards the rear bumper, then proceed to either the right or left working your way around the trunk opening and back to the seam. As you work the new weatherstrip into position, make sure it is fully seated onto the trunk opening body flange evenly with no high spots (which will result when the weatherstrip is not fully seated). Position the inner lip over the trunk lining trim as shown in the photo below, right.
As an extra “check” to confirm the weatherstrip is installed properly, the white dot on the outside must face the rear window.
NOTES:
- To avoid damaging the new weatherstrip, DO NOT use any tool other than your hands (no rubber mallets or similar tools) to fully seat it onto the body flange.
- In the event combination lamp replacement is needed, refer to TSB 12-145-13R for revised retaining nut and sealing gasket information.
2 Affected Products
Vehicle
| MAKE | MODEL | YEAR |
| SUBARU | BRZ | 2013-2014 |
1 Associated Document
Manufacturer Communications
NUMBER: 12-160-13
DATE: 12/23/13
MC-10233084-9999.pdf 640.419KB
- Lights Dim Over Time, Replace In Pairs: Your lights are a pair, one is never turned on without the other. If one bulb burns out, the other isn't far behind
- Verify fitment: Navigate to the Amazon Confirmed Fit tool at the top of the page (desktop) or under the images (mobile). Plug in your vehicle info and check the bulb fitment location to ensure this product will work for your needs
- Easy To Replace: Sylvania Long Life miniature bulbs are easy to install and show instant results
- Low Maintenance And High Durability: Designed for durability, greater safety, and lower maintenance by the leading supplier of automotive lighting
- Longer Life Than Most Standard Bulbs: Long Life bulbs perform twice as long as any other standard miniature bulbs
- LIGHTS DIM OVER TIME, REPLACE IN PAIRS: Your lights are a pair, one is never turned on without the other. If one bulb burns out, the other isn't far behind.
- EASY TO REPLACE: Sylvania Long Life miniature bulbs are easy to install and show instant results.
- LOW MAINTENANCE AND HIGH DURABILITY: Designed for durability, greater safety, and lower maintenance by the leading supplier of automotive lighting.
- LONGER LIFE THAN MOST STANDARD BULBS: Long Life bulbs perform twice as long as any other standard miniature bulbs.
- THE SYLVANIA STANDARD OF QUALITY: With 100+ years in business, Sylvania is the world leader in automotive lighting for Original Equipment Manufacturers (OEMs) and the aftermarket.
- Set of 2 Bulbs with 54SMD 3014 & 3SMD 3030 high brightness chips per bulb, Working Voltage: 12v-24v.
- Fits: 3056 3057 3057K 3057LL 3155 3157 3157K 3157NA 3156NA 3156A 3156 3156K 3357KNA 3357LL 3457 4057 4057K 4114 4114K 4157 4157K 4157NA etc. Easy installation, plug and play.
- Application: Back Up Reverse Lights, Tail Brake Lights, Turn Signal Lights, Tail Lights, Parking Lights, Side Marker Lights, Daytime Running Lights etc. Load resistor or flash relay might be needed to prevent the hyper flash or system error.
- Advantage: Non-polarity design, more than 300% brighter than original halogen bulb, full Aluminum Housing with Projection lens for Maximum Light output and better heat distribution, built in Constant Current IC for Longer life span & Low Power Consumption.
- Please double check owners manual or original bulb number to confirm before placing an order. Any other problem please feel free to contact us, we are always here to satisfy of you. (New design launched in 2019, US Patent number US-D908272-S)
- Excellent Lighting: With a color temperature of 3000K and a brightness of 54lm, this 3157 taillight bulb provides even and stable light, significantly improving visibility when braking. Its 360-degree lighting effect ensures that the surrounding environment is fully illuminated, and the non-flickering light effectively improves night driving safety
- Quartz Glass Material: High temperature resistant, impact resistant, compact in size, with good light transmission and light gathering effect, and featuring a waterproof design that adapts to humid environments for long-term stable lighting, this rear turn signal bulb made of quartz glass meets diversified needs
- Product Parameters: Rated at 12V, with 21W power, 3000K color temperature, 54lm lumen, and a service time of about 500 hours, this break light bulb replacement model 3157 comes in a pack of 10 for daily use. Please verify compatibility with your model before purchasing
- Non-destructive Installation: Designed with a standard plug for easy installation, causing no CAN-Bus error codes or bulb flickering, and preserving the car’s original control circuit system, this 3157 halogen bulb ensures stable operation with its good thermal conductivity and heat dissipation
- Widely Universal: Used as a tail light, side marker light, brake light and instrument light for most types of vehicles such as cars, SUVs, trucks and more, this automotive brake bulb has a wide range of applications and is an ideal universal automotive lighting accessory
- Lights Dim Over Time, Replace In Pairs: Your lights are a pair, one is never turned on without the other. If one bulb burns out, the other isn't far behind.
- Easy To Replace: Sylvania Long Life miniature bulbs are easy to install and show instant results.
- Low Maintenance And High Durability: Designed for durability, greater safety, and lower maintenance by the leading supplier of automotive lighting.
- Longer Life Than Most Standard Bulbs: Long Life bulbs perform twice as long as any other standard miniature bulbs.
- The Sylvania Standard Of Quality: With over 100 years in business, Sylvania is the world leader in automotive lighting for Original Equipment Manufacturers (OEMs) and the aftermarket.
SEOCONTENT-START
Bulletin Number: 12-160-13; Date: 12/23/13 Page 1 INTRODUCTION This bulletin announces availability of a revised trunk weatherstrip and rubber stoppers designed to absorb impact and prevent contact or in rare occurrences, damage to the rear combination lamps when closing the trunk lid. COUNTERMEASURE IN PRODUCTION The new weatherstrip and rubber trunk stoppers were incorporated into production starting with the following VINs: Weatherstrip E*600523 Rubber Trunk Stoppers E*601334 PART INFORMATION A liner was added into the weatherstrip for increased resistance to crush and the trunk stopper’s overall height was increased by 2.7mm to minimize the chance of trunk lid contact with the combination lamps. PART NAME PART NUMBER WSTR Trunk 57532CA001 Stopper Trunk Lower 57533FE040 NUMBER: 12-160-13 DATE: 12/23/13 APPLICABILITY: 2013-14MY BRZ SUBJECT: Cracked Rear Combination Lamps SERVICE BULLETIN ATTENTION: GENERAL MANAGER q PARTS MANAGER q CLAIMS PERSONNEL q SERVICE MANAGER q IMPORTANT – All Service Personnel Should Read and Initial in the boxes provided, right. Continued… CAUTION: VEHICLE SERVICING PERFORMED BY UNTRAINED PERSONS COULD RESULT IN SERIOUS INJURY TO THOSE PERSONS OR TO OTHERS. Subaru Service Bulletins are intended for use by professional technicians ONLY. They are written to inform those technicians of conditions that may occur in some vehicles, or to provide information that could assist in the proper servicing of the vehicle. Properly trained technicians have the equipment, tools, safety instructions, and know-how to do the job correctly and safely. If a condition is described, DO NOT assume that this Service Bulletin applies to your vehicle, or that your vehicle will have that condition. SUBARU OF AMERICA, INC. IS “ISO 14001 COMPLIANT” The international standard for excellence in Environmental Management Systems. Please recycle or dispose of automotive products in a manner that is friendly to our environment and in accordance with all local, state and federal laws and regulations. OLD NEW Bulletin Number: 12-160-13; Date: 12/23/13 Page 2 SERVICE PROCEDURE / INFORMATION To remove the trunk stopper, use a plastic trim tool to lift up and release one of the retaining tangs. Once you have one side released, hold the one side of the stopper away from the body then release the opposite tang with the plastic trim tool as shown in the photos below. Grasp and pull up on the old weatherstrip to release and remove it from the trunk opening body flange. Leave any adhesive remaining on the flange in place to help secure the new weatherstrip. Start the installation with the seam aligned with the striker, arrow and notch towards the rear bumper, then proceed to either the right or left working your way around the trunk opening and back to the seam. As you work the new weatherstrip into position, make sure it is fully seated onto the trunk opening body flange evenly with no high spots (which will result when the weatherstrip is not fully seated). Position the inner lip over the trunk lining trim as shown in the photo below, right. Release One Tang Tang Released Hold Onto Stopper and Release the Opposite Side Tang Retaining “Tangs” Trunk Stopper Weatherstrip Trunk Stopper (closest to the trunk latch) Trunk Stopper (closest to the trunk latch) Arrow Inner lip properly covering edge of trunk lining trim Notch Bulletin Number: 12-160-13; Date: 12/23/13 Page 3 As an extra “check” to confirm the weatherstrip is installed properly, the white dot on the outside must face the rear window. NOTES: • To avoid damaging the new weatherstrip, DO NOT use any tool other than your hands (no rubber mallets or similar tools) to fully seat it onto the body flange. • In the event combination lamp replacement is needed, refer to TSB 12-145-13R for revised retaining nut and sealing gasket information. WARRANTY / CLAIM INFORMATION For vehicles within the Basic New Car Limited Warranty period, this repair may be claimed using the following information: LABOR DESCRIPTION LABOR OPERATION # FAIL CODE LABOR TIME TRUNK WEATHER STRIP & STOPPER REPLACEMENT B914-743 WBB-48 0.2 ONE BRZ REAR COMBINATION LIGHT ASSEMBLY REPLACE C914-742 0.2 BOTH BRZ REAR COMBINATION LIGHT ASSEMBLIES REPLACE C914-744 0.3 Rear Glass
SEOCONTENT-END
This product presentation was made with AAWP plugin.