NHTSA ID Number: 10160211
Manufacturer Communication Number: 07-150-19
Summary
This bulletin provides a procedure for replacing the rear combination lamp wiring harness. The harness is now available as a service part separate from the lamp assembly.
4 Affected Products
Vehicle
INTRODUCTION:
This bulletin provides a procedure for replacing the rear combination lamp wiring harness. The harness is now available as a service part separate from the lamp assembly.
PART INFORMATION:
The wiring harness part number is: 84981VA140.
REMINDERS:
- Always order the most up-to-date replacement parts based on the specific VIN being repaired.
- The packing (gasket) between the lamp assembly and the rear body panel is a one-time use item and MUST be replaced whenever the lamp assembly is removed.
SERVICE PROCEDURE / INFORMATION:
REMINDER: Customer satisfaction and retention starts with performing quality repairs.
Although the procedure for replacing the combination lamp wiring harness is new, the Service Manual procedure for removing and installing the complete lamp assemblies is unchanged. The existing Service Manual procedures contain information critical to performing an effective repair the first time and every time. This includes but is not limited to: important SAFETY precautions, proper inspection criteria, necessary special tools, required processes and related one-time-use parts needed for a complete and lasting repair.
IMPORTANT: Before the harness can be removed from the lamp housing, a portion of the connector lock must be CAREFULLY trimmed away. Use a good, sharp wire cutter as shown below while being careful to not damage the tab portion of the housing the connector slides and locks back onto.
- Install the new harness onto the housing and re-assemble in reverse order of removal. REMINDER: Don’t forget to reinstall the foam block (packing) and always use a new lamp to body gasket.
- Confirm all the functions of the combination lamp operate normally to complete the procedure.
SEOCONTENT-START
Bulletin Number: 07-150-19; Date: 04/17/19 Page 1 of 3
Continued…
NUMBER: 07-150-19
DATE: 04/17/19
APPLICABILITY: 2015-18MY WRX
SUBJECT: Rear Combination Lamp Harness
Replacement Procedure
CAUTION: VEHICLE SERVICING PERFORMED BY UNTRAINED PERSONS COULD
RESULT IN SERIOUS INJURY TO THOSE PERSONS OR TO OTHERS.
Subaru Service Bulletins are intended for use by professional technicians ONLY. They
are written to inform those technicians of conditions that may occur in some vehicles,
or to provide information that could assist in the proper servicing of the vehicle. Properly
trained technicians have the equipment, tools, safety instructions, and know-how to
do the job correctly and safely. If a condition is described, DO NOT assume that this
Service Bulletin applies to your vehicle, or that your vehicle will have that condition.
Subaru of America, Inc. is
ISO 14001 Compliant
ISO 14001 is the international standard for
excellence in Environmental Management
Systems. Please recycle or dispose of
automotive products in a manner that is friendly
to our environment and in accordance with all
local, state and federal laws and regulations.
INTRODUCTION:
This bulletin provides a procedure for replacing the
rear combination lamp wiring harness. The harness is
now available as a service part separate from the lamp
assembly.
PART INFORMATION:
The wiring harness part number is: 84981VA140.
REMINDERS:
• Always order the most up-to-date replacement parts based on the specific VIN being
repaired.
• The packing (gasket) between the lamp assembly and the rear body panel is a one-time use
item and MUST be replaced whenever the lamp assembly is removed.
SERVICE PROCEDURE / INFORMATION:
REMINDER: Customer satisfaction and retention starts with performing quality repairs.
Although the procedure for replacing the combination lamp wiring harness is new, the Service
Manual procedure for removing and installing the complete lamp assemblies is unchanged. The
existing Service Manual procedures contain information critical to performing an effective repair the
first time and every time. This includes but is not limited to: important SAFETY precautions, proper
inspection criteria, necessary special tools, required processes and related one-time-use parts needed
for a complete and lasting repair.
SERVICE BULLETIN
ATTENTION:
GENERAL MANAGER q
PARTS MANAGER q
CLAIMS PERSONNEL q
SERVICE MANAGER q
IMPORTANT – All
Service Personnel
Should Read and
Initial in the boxes
provided, right.
©2019 Subaru of America, Inc. All rights reserved.
Bulletin Number: 07-150-19; Date: 04/17/19 Page 2 of 3
Continued…
• Remove the affected lamp assembly following the
procedure in the applicable Service Manual.
• Remove the gasket to access the harness and the
foam block (packing) shown in the photo.
• Disconnect the LED harness connector then remove the
bulb socket assemblies. Transfer the bulbs over to the new
harness.
LED Harness
Connector
IMPORTANT: Before the harness can be removed from the lamp housing, a portion of the
connector lock must be CAREFULLY trimmed away. Use a good, sharp wire cutter as shown below
while being careful to not damage the tab portion of the housing the connector slides and locks back
onto.
• Install the new harness onto the housing and re-assemble in reverse order of removal.
REMINDER: Don’t forget to reinstall the foam block (packing) and always use a new lamp
to body gasket.
• Confirm all the functions of the combination lamp operate normally to complete the
procedure.
Packing
Bulletin Number: 07-150-19; Date: 04/17/19 Page 3 of 3
WARRANTY / CLAIM INFORMATION:
For vehicles within the Basic New Car Limited Warranty period or covered by an active Subaru
Added Security Classic or Gold plan, this repair may be submitted using the following claim
information:
Labor Description Labor Operation # Fail
Code
Labor
Time
REAR COMBINATION LAMP HARNESS, RIGHT SIDE R&R
B838-753
UWC-43 0.3
REAR COMBINATION LAMP HARNESS, LEFT SIDE R&R UWD-43 0.3
REAR COMBINATION LAMP HARNESSES, BOTH SIDES R&R B838-754 UWE-43 0.5
REAR COMBINATION LAMP TESTING & DIAGNOSIS C838-001 ** 0.5
** When claiming C838-001 for testing, use the Fail Code for the lamp being repaired.
IMPORTANT REMINDERS:
• SOA strongly discourages the printing and/or local storage of service information as
previously released information and electronic publications may be updated at any time.
• Always check for any open recalls or campaigns anytime a vehicle is in for servicing.
• Always refer to STIS for the latest service information before performing any repairs.
NUMBER: 07-150-19
DATE: 04/17/19
- Lights Dim Over Time, Replace In Pairs: Your lights are a pair, one is never turned on without the other. If one bulb burns out, the other isn't far behind
- Verify fitment: Navigate to the Amazon Confirmed Fit tool at the top of the page (desktop) or under the images (mobile). Plug in your vehicle info and check the bulb fitment location to ensure this product will work for your needs
- Easy To Replace: Sylvania Long Life miniature bulbs are easy to install and show instant results
- Low Maintenance And High Durability: Designed for durability, greater safety, and lower maintenance by the leading supplier of automotive lighting
- Longer Life Than Most Standard Bulbs: Long Life bulbs perform twice as long as any other standard miniature bulbs
- LIGHTS DIM OVER TIME, REPLACE IN PAIRS: Your lights are a pair, one is never turned on without the other. If one bulb burns out, the other isn't far behind.
- EASY TO REPLACE: Sylvania Long Life miniature bulbs are easy to install and show instant results.
- LOW MAINTENANCE AND HIGH DURABILITY: Designed for durability, greater safety, and lower maintenance by the leading supplier of automotive lighting.
- LONGER LIFE THAN MOST STANDARD BULBS: Long Life bulbs perform twice as long as any other standard miniature bulbs.
- THE SYLVANIA STANDARD OF QUALITY: With 100+ years in business, Sylvania is the world leader in automotive lighting for Original Equipment Manufacturers (OEMs) and the aftermarket.
- Set of 2 Bulbs with 54SMD 3014 & 3SMD 3030 high brightness chips per bulb, Working Voltage: 12v-24v.
- Fits: 3056 3057 3057K 3057LL 3155 3157 3157K 3157NA 3156NA 3156A 3156 3156K 3357KNA 3357LL 3457 4057 4057K 4114 4114K 4157 4157K 4157NA etc. Easy installation, plug and play.
- Application: Back Up Reverse Lights, Tail Brake Lights, Turn Signal Lights, Tail Lights, Parking Lights, Side Marker Lights, Daytime Running Lights etc. Load resistor or flash relay might be needed to prevent the hyper flash or system error.
- Advantage: Non-polarity design, more than 300% brighter than original halogen bulb, full Aluminum Housing with Projection lens for Maximum Light output and better heat distribution, built in Constant Current IC for Longer life span & Low Power Consumption.
- Please double check owners manual or original bulb number to confirm before placing an order. Any other problem please feel free to contact us, we are always here to satisfy of you. (New design launched in 2019, US Patent number US-D908272-S)
- Excellent Lighting: With a color temperature of 3000K and a brightness of 54lm, this 3157 taillight bulb provides even and stable light, significantly improving visibility when braking. Its 360-degree lighting effect ensures that the surrounding environment is fully illuminated, and the non-flickering light effectively improves night driving safety
- Quartz Glass Material: High temperature resistant, impact resistant, compact in size, with good light transmission and light gathering effect, and featuring a waterproof design that adapts to humid environments for long-term stable lighting, this rear turn signal bulb made of quartz glass meets diversified needs
- Product Parameters: Rated at 12V, with 21W power, 3000K color temperature, 54lm lumen, and a service time of about 500 hours, this break light bulb replacement model 3157 comes in a pack of 10 for daily use. Please verify compatibility with your model before purchasing
- Non-destructive Installation: Designed with a standard plug for easy installation, causing no CAN-Bus error codes or bulb flickering, and preserving the car’s original control circuit system, this 3157 halogen bulb ensures stable operation with its good thermal conductivity and heat dissipation
- Widely Universal: Used as a tail light, side marker light, brake light and instrument light for most types of vehicles such as cars, SUVs, trucks and more, this automotive brake bulb has a wide range of applications and is an ideal universal automotive lighting accessory
- Lights Dim Over Time, Replace In Pairs: Your lights are a pair, one is never turned on without the other. If one bulb burns out, the other isn't far behind.
- Easy To Replace: Sylvania Long Life miniature bulbs are easy to install and show instant results.
- Low Maintenance And High Durability: Designed for durability, greater safety, and lower maintenance by the leading supplier of automotive lighting.
- Longer Life Than Most Standard Bulbs: Long Life bulbs perform twice as long as any other standard miniature bulbs.
- The Sylvania Standard Of Quality: With over 100 years in business, Sylvania is the world leader in automotive lighting for Original Equipment Manufacturers (OEMs) and the aftermarket.
This product presentation was made with AAWP plugin.