Accessory Installation Guide
| RES FOB TRANSCEIVER REPLACEMENT KIT
2017-2020 Impreza | H001SFL020 |
SEOCONTENT-START
PART NUMBER 1 OF 2
H001SFL020
ISSUE
00
DATE
13 Oct 2016 SUBARU OF AMERICA
PART NUMBER 1 OF 2
H001SFL020
ISSUE
00
DATE
13 Oct 2016 SUBARU OF AMERICA
PART NUMBER 1 OF 2
H001SSG460
ISSUE
01
DATE
12 May 2016 SUBARU OF AMERICA
PART NUMBER 1 OF 2
H001SSG460
ISSUE
01
DATE
12 May 2016 SUBARU OF AMERICA
1
2
KIT CONTENTS
FOB PROGRAMMING (TURN START MODELS)
Remote Engine Start
Fob / Transceiver
Quantity=1
INSTALLATION
INSTRUCTIONS
PART NUMBER: H001SSG460
DESCRIPTION: RES FOB TRANSCEIVER
REPLACEMENT KIT
Programming
Instructions
Quantity=1
1. Open the driver’s door and enter the vehicle. The driver’s door must remain open throughout the entire
programming process. Ensure all other vehicle doors, trunk, hatch or rear gate are closed.
2. Verify that the transmission shifter is in the “park” position.
3. Press and hold the vehicle’s brake pedal.
4. Turn the ignition “ON” then “OFF”, “ON” then “OFF”, “ON” then “OFF”, then back “ON” and leave on throughout
the entire programming process. (ON/OFF ignition cycles must be completed within fi ve (5) seconds.)
5. The system will fl ash the side marker lights, taillights and parking lights and honk the horn three (3) times
indicating that the system has entered fob learn mode.
6. Press and release the button on the fob to be learned.
7. The system will fl ash the side marker lights, taillights and parking lights and honk the horn one (1) time,
indicating that the system has learned the fob. Upon successful programming, the remote start fob may
fl ash/beep one (1) time.
8. Repeat step six (6) for additional fobs. The system will accept up to eight (8) fobs.
9. Turn the ignition OFF to exit fob learn mode.
NOTE: The system will exit the fob learn mode if the ignition is turned OFF, the driver’s door is closed or two (2)
minutes of inactivity.
IMPORTANT! THIS SECTION ONLY APPLIES TO VEHICLES EQUIPPED WITH A KEY START
IGNITION SYSTEM. FOR VEHICLES EQUIPPED WITH A PUSH BUTTON IGNITION SYSTEM,
DISREGARD THIS SECTION AND PROCEED TO SECTION 3.
1
2
KIT CONTENTS
FOB PROGRAMMING (TURN START MODELS)
Remote Engine Start
Fob / Transceiver
Quantity=1
INSTALLATION
INSTRUCTIONS
PART NUMBER: H001SSG460
DESCRIPTION: RES FOB TRANSCEIVER
REPLACEMENT KIT
Programming
Instructions
Quantity=1
1. Open the driver’s door and enter the vehicle. The driver’s door must remain open throughout the entire
programming process. Ensure all other vehicle doors, trunk, hatch or rear gate are closed.
2. Verify that the transmission shifter is in the “park” position.
3. Press and hold the vehicle’s brake pedal.
4. Turn the ignition “ON” then “OFF”, “ON” then “OFF”, “ON” then “OFF”, then back “ON” and leave on throughout
the entire programming process. (ON/OFF ignition cycles must be completed within fi ve (5) seconds.)
5. The system will fl ash the side marker lights, taillights and parking lights and honk the horn three (3) times
indicating that the system has entered fob learn mode.
6. Press and release the button on the fob to be learned.
7. The system will fl ash the side marker lights, taillights and parking lights and honk the horn one (1) time,
indicating that the system has learned the fob. Upon successful programming, the remote start fob may
fl ash/beep one (1) time.
8. Repeat step six (6) for additional fobs. The system will accept up to eight (8) fobs.
9. Turn the ignition OFF to exit fob learn mode.
NOTE: The system will exit the fob learn mode if the ignition is turned OFF, the driver’s door is closed or two (2)
minutes of inactivity.
IMPORTANT! THIS SECTION ONLY APPLIES TO VEHICLES EQUIPPED WITH A KEY START
IGNITION SYSTEM. FOR VEHICLES EQUIPPED WITH A PUSH BUTTON IGNITION SYSTEM,
DISREGARD THIS SECTION AND PROCEED TO SECTION 3.
1
2
KIT CONTENTS
FOB PROGRAMMING (TURN START MODELS)
Remote Engine Start
Fob / Transceiver
Quantity=1
INSTALLATION
INSTRUCTIONS
PART NUMBER: H001SFL020
DESCRIPTION: RES FOB TRANSCEIVER
REPLACEMENT KIT
Programming
Instructions
Quantity=1
1. Open the driver’s door and enter the vehicle. The driver’s door must remain open throughout the entire
programming process. Ensure all other vehicle doors, trunk, hatch or rear gate are closed.
2. Verify that the transmission shifter is in the “park” position.
3. Turn the ignition “ON” then “OFF”, “ON” then “OFF”, “ON” then “OFF”, then back “ON” and leave on throughout
the entire programming process. (ON/OFF ignition cycles must be completed within fi ve (5) seconds.)
4. The system will fl ash the side marker lights, taillights and parking lights and honk the horn three (3) times
indicating that the system has entered fob learn mode.
5. Press and hold the button on the fob to be learned for three (3) seconds until the system fl ashes the side
marker lights, taillights and parking lights and honks the horn one (1) time, indicating that the system has learned
the fob. Release the button. Upon successful programming, the remote start fob may fl ash/beep one (1)
time.
6. Repeat step fi ve (5) for additional fobs. The system will accept up to eight (8) fobs.
7. Turn the ignition OFF to exit fob learn mode.
NOTE: The system will exit the fob learn mode if the ignition is turned OFF, the driver’s door is closed or
thirty (30) seconds of inactivity.
IMPORTANT! THIS SECTION ONLY APPLIES TO VEHICLES EQUIPPED WITH A KEY START
IGNITION SYSTEM. FOR VEHICLES EQUIPPED WITH A PUSH BUTTON IGNITION SYSTEM,
DISREGARD THIS SECTION AND PROCEED TO SECTION 3.
1
2
KIT CONTENTS
FOB PROGRAMMING (TURN START MODELS)
Remote Engine Start
Fob / Transceiver
Quantity=1
INSTALLATION
INSTRUCTIONS
PART NUMBER: H001SFL020
DESCRIPTION: RES FOB TRANSCEIVER
REPLACEMENT KIT
Programming
Instructions
Quantity=1
1. Open the driver’s door and enter the vehicle. The driver’s door must remain open throughout the entire
programming process. Ensure all other vehicle doors, trunk, hatch or rear gate are closed.
2. Verify that the transmission shifter is in the “park” position.
3. Turn the ignition “ON” then “OFF”, “ON” then “OFF”, “ON” then “OFF”, then back “ON” and leave on throughout
the entire programming process. (ON/OFF ignition cycles must be completed within fi ve (5) seconds.)
4. The system will fl ash the side marker lights, taillights and parking lights and honk the horn three (3) times
indicating that the system has entered fob learn mode.
5. Press and hold the button on the fob to be learned for three (3) seconds until the system fl ashes the side
marker lights, taillights and parking lights and honks the horn one (1) time, indicating that the system has learned
the fob. Release the button. Upon successful programming, the remote start fob may fl ash/beep one (1)
time.
6. Repeat step fi ve (5) for additional fobs. The system will accept up to eight (8) fobs.
7. Turn the ignition OFF to exit fob learn mode.
NOTE: The system will exit the fob learn mode if the ignition is turned OFF, the driver’s door is closed or
thirty (30) seconds of inactivity.
IMPORTANT! THIS SECTION ONLY APPLIES TO VEHICLES EQUIPPED WITH A KEY START
IGNITION SYSTEM. FOR VEHICLES EQUIPPED WITH A PUSH BUTTON IGNITION SYSTEM,
DISREGARD THIS SECTION AND PROCEED TO SECTION 3.
4280698 Rev – 10/13/16
PART NUMBER 2 OF 2
H001SFL020
ISSUE
00
DATE
13 Oct 2016 SUBARU OF AMERICA
3 FOB PROGRAMMING (PUSH START MODELS)
1. Open the driver’s door and enter the vehicle. The driver’s door must remain open throughout the entire
programming process. Ensure all other vehicle doors, trunk, hatch or rear gate are closed.
2. Verify that the transmission shifter is in the “park” position.
3. Turn the ignition “ON” then “OFF”, “ON” then “OFF”, “ON” then “OFF”, then back “ON” and leave on throughout
the entire programming process. (Turn ON the ignition by pressing the Engine Start/Stop button on the
dashboard two (2) times with an Access Key inside the vehicle. Do not press the brake pedal or the engine will
start.) (ON/OFF ignition cycles must be completed within twenty (20) seconds.)
4. The system will fl ash the side marker lights, taillights and parking lights and honk the horn three (3) times
indicating that the system has entered fob learn mode.
5. Press and hold the button on the fob to be learned for three (3) seconds until the system fl ashes the side
marker lights, taillights and parking lights and honks the horn one (1) time, indicating that the system has learned
the fob. Release the button. Upon successful programming, the remote start fob may fl ash/beep one (1)
time.
6. Repeat step fi ve (5) for additional fobs. The system will accept up to eight (8) fobs.
7. Turn the ignition OFF to exit fob learn mode.
NOTE: The system will exit the fob learn mode if the ignition is turned OFF, the driver’s door is closed or
thirty (30) seconds of inactivity.
IMPORTANT! THIS SECTION ONLY APPLIES TO VEHICLES EQUIPPED WITH A PUSH BUTTON
IGNITION SYSTEM. FOR VEHICLES EQUIPPED WITH A KEY START IGNITION SYSTEM,
DISREGARD THIS SECTION AND RETURN TO SECTION 2.
SEOCONTENT-END
- Compatibility : This remote key fits for Subaru Ascent 2019-2024,for Crosstrek 2019-2023,for Forester 2019-2023,for Impreza 2017-2023,for Legacy 2018-2021,for Outback 2018-2023,for BRZ 2022 2023 2024,for WRX STI 2019-2021
- Confirm It Fits for Your Car: Please check the appearance of the key fob(including key buttons and shape); then check if your key has the same part number,Frequency: 433MHz,Chip: 8A,Board ID: 231451-7000,FCC ID: HYQ14AHK,OEM P/N: 88835-FL03A, 88835-FL03B, 88835-FL03C
- How to check part number: Open your original key, then you can see the part information on the key shell or the circuit board, just compare it to my key fob. If you lost your key, you need check with your dealership
- Key Programming and Cutting: You need program and cut the remote fob to your vehicle before it can work on your car by a locksmith or the dealership
- Complete Remote Key Fob: The package includes battery, uncut blade, 8A chip and circuit board, it will function is same as your original one, just ready to program
- Self-Programming Capability: This key fob replacement is designed for easy, self-programming, making it a convenient DIY solution. You won't need professional assistance to set it up-just follow the simple instructions provided. In just a few easy steps, you can program the fob to your vehicle, restoring full functionality without costly visits to the dealership. It's a quick, cost-effective way to replace a lost or damaged key fob while maintaining convenience and security
- Premium Replacement Quality: This car fob is designed to match the specifications of the factory remote. Unlike generic alternatives, this premium replacement ensures a seamless integration with your car's security system, maintaining the same high-quality performance while offering an affordable and convenient option for replacing a lost or damaged remote (PN: 88036SC030)
- Three-Button Functionality: This Keyless Option replacement remote features convenient 3-button options, providing a range of functions for added security and ease of use with your vehicle's keyless entry system
- Complete Package Included: This product comes as a complete key fob with electronics and a battery already installed, ready for programming and immediate use upon delivery
- Vehicle Compatibility: This car remote can only be programmed for specific Makes and Models including 1999-2011 Subaru Impreza, Legacy, WRX, and Outback vehicles. Please verify compatibility with your vehicle before purchase
- 【Replacement】For FCC ID:HYQ14AHK; P/N:88835FL032, 88835FL031, 88835FL030, 88835-FL03C, 88835-FL03B, 88835-FL03A; Frequency:434 MHz; Please Make Sure That Your Original Remote Has the Same Buttons on it
- 【Compatibility】Compatible with 2019-2024 Subaru Ascent/ 19-23 Crosstrek Forester/ 17-23 Impreza/ 18-21 Legacy/ 18-23 Outback/ 22-24 BRZ/ 19-21 WRX STI. Please Check Our Product Description and Vehicle Fitment Tool for Full Compatible Vehicles List
- 【Programming Methord】Self-Programming is Not Available, it's necessary to be cut and programmed by a qualified dealer or locksmith.【NOTE】This Key Fob Only Supports Vehicles Equipped with Push to Start / Stop Button on The Dashboard and Proxy Keyless Entry System. It Doesn’t Support Regular Key/Keyed Ignition Vehicles.
- 【OEM-Quality】Made of Premium Plastic Materials, Shockproof, Every Single Keyless Entry Remote Start Control Car Key Fob is Fully Pre-tested by Professional Locksmith Tools before Shipping. 100% New Brand Remote Control Car Key Fob, The Function is the Same as the Factory Original Car Key Fob.
- 【Package Include】1x Keyless Entry Remote Start Control Key Fob with Electronics and Battery Pre-Installed.【WARRANTY】Buy with Confidence, 24-Months Warranty and Lifetime Support. If You Find They Don't Work or Any Problems, Just Feel Free to Contact us Anytime, We Will Arrange Free Refund or Return for You
- Only Key Fob Shell: This is just a key shell case replacement with no electronics, transponder chip, or battery inside.
- Fitment: An empty key fob cover shell replacement compatibility with 2014-2022 Subaru BRZ, 2015-2022 Legacy & Crosstrek, 2015-2023 Outback & Impreza, 2016-2018 Forester, 2016-2023 Subaru WRX & STI, 2019-2022 Ascent Fits for FCC ID: HYQ14AHK.
- Installation: Our remote key fob shell case is easy to install. Just open your original key fob control and then put the internals like a circuit board in this new key case shell. (Does not require reprogramming). The New Blank key needs to be cut by a hardware store or locksmith.
- Materials: Mixed metal and plastic composition, durable replacement key shell case. It is a good replacement key fob case for broken or worn remotes.
- Remote Key Shell Appearance: Please check the button position and appearance of your car remote fob key is the same as our key case shell before you buy.
- COMPATIBILITY:Compatible with FCC ID:HYQ14AHC,Part Numbers:88835-AL04A,Frequency:315 MHz.Please verify your key matches these specifications before purchasing.
- REPLACEMENT:Compatible with Subaru BRZ 2014-2020 Subaru Forester Impreza WRX STI/Impreza WRX 2016-2018 Subaru Legacy Outback 2015-2017 Subaru Crosstrek XV Impreza 2015-2016,Please confirm your vehicle’s model and year are in our compatibility list
- PROGRAMMING: Requires programming and metal key cutting by a professional locksmith. Self-programming is not supported. This is an aftermarket key fob, non-OEM, without logo or brand markings.
- HIGH QUALITY: 100% brand-new key fob with pre-installed battery and electronics, fully tested with professional equipment before shipment.
- CUSTOMER SERVICE: We support refunds or replacements within 3 months. If you have any questions during purchase or use, please leave a message and the customer support team will provide professional help within 24 hours.
This product presentation was made with AAWP plugin.