NHTSA ID Number: 10144880
Manufacturer Communication Number: 12-249-18
Summary
This Service Information bulletin advises of a design change made to the rear body panel. This panel is located between the trunk and the rear glass and incorporates the package shelf. It has been re-designed with convex surfaces added to prevent items going into or out of the trunk from being scratched or caught by the rear edges of the reinforcement panels.
3 Affected Products
Vehicle
| SUBARU | LEGACY | 2015-2017 |
INTRODUCTION:
This Service Information bulletin advises of a design change made to the rear body panel. This panel is located between the trunk and the rear glass and incorporates the package shelf. It has been re-designed with 2 convex surfaces added to prevent items going into or out of the trunk from being scratched or caught by the rear edges of the reinforcement panels (shown in red) on the illustrations below.
View from inside trunk area looking upward toward underside of package shelf.
PRODUCTION CHANGE INFORMATION:
This new body panel was put into production during mid-April, 2017. The starting VIN will be added to this bulletin when it becomes available.
PART INFORMATION:
The new part numbers for the “PANEL COMPLETE R” are 53105AL02C9P and 53105AL03C9P.
Always order the most up-to-date part as specified by the VIN.
SERVICE PROCEDURE / INFORMATION:
REMINDER: Customer satisfaction and retention starts with performing quality repairs.
The service procedures for replacement of the panel remain unchanged. Always refer to the applicable Body Repair Manual and Service Manual to review the full requirements of the repair being performed before proceeding. The Manual procedures contain information critical to performing an effective repair the first time and every time. This includes but is not limited to:
important SAFETY precautions, proper inspection criteria, necessary special tools, required processes and related one-time-use parts needed for a complete and lasting repair.
SEOCONTENT-START
APPLICABILITY: 2015-2017MY Legacy
SUBJECT: Rear Body Panel- Design Change
IMPORTANT REMINDERS:
- SOA strongly discourages the printing and/or local storage of service information as previously released information and electronic publications may be updated at any time.
- Always check for any open recalls or campaigns anytime a vehicle is in for servicing.
- Always refer to STIS for the latest service information before performing any repairs.
SEOCONTENT-END
NUMBER: 12-249-18
DATE: 08-15-18
- 40pcs 90914-0007 Bumper, Engine Cover, Fender & Grille Push-Type Retainer for Subaru Baja, Forester, Impreza, Legacy, Outback & Tribeca 2011 - 2000
- 30pcs 90913-0067 Engine Cover and Fender Liner for Subaru B9, Forester, Legacy, Outback & Tribeca 2005 -
- 30pcs 90914-0051 Front Bumper & Quarter Panel Push-Type Retainer for Subaru Impreza, Legacy, Outback & Tribeca 2011 - 2005
- FITS VARIOUS SUBARU MODELS - The clips fit selected Subaru as well some other car brands.
- Premium OEM Upgraded Quality and Durable —Made of Premium Auto Grade Nylon：PA66(Not Ordinary Cheap Nylon),solid like metal.
- 30Pcs 90914-0007 Push-type clip replace for Ascent, B9 Tribeca, Baja, BRZ, Crosstrek, Forester, Impreza, Legacy, Outback, Tribeca, WRX, WRX STI, XV Crosstrek work on Bumper, Engine Cover, Fender & Grille
- 30Pcs 90914-0065 body clips replace for Ascent, BRZ, Crosstrek, Forester, Impreza, Legacy, Outback, WRX, WRX STI, XV Crosstrek work on Front Fender Liner, Engine Cover, Hood & Quarter Panel
- 30Pcs 90914-0051 Front bumper & quarter panel push-type retainer compatible with BRZ, Legacy, Outback, Tribeca, Head Diameter: 20mm, Hole Size: 7mm, Stem Length: 9mm
- 30Pcs MR200300 Rocker molding push-type retainer compatible with Ascent, Crosstrek, Forester, Impreza, Legacy, Outback, Tribeca, WRX, WRX STI, XV Crosstrek, Fits Into 9mm Hole
- 4 different sizes in the bag each one came in handy and it came with 1 tool, exact match for the factory clips. also must have for most Japanese cars repair or upgrade like honda & nissan and toyota
- 🔧 Multiple Solutions- Includes 19 Sizes of Subaru Body Interior and Exterior Retainer Fastener Clip, Total 190 Pieces. These Are Reliable Replacement for the Original Part That had Missing or Failed Due to Fatigue.
- ✅ Durable Construction - These Clips are Made from Quality Nylon Materials to Ensure Reliable Performance and Long Service Life.
- 🚗 Fits Most Subaru Models, Including Hood Insulation Retainer, Front & Rear Bumper Push-Type Retainer, Front Fender, Bumper & Quarter Panel Push-Type Retainer, Front Fender Liner, Engine Cover, Hood & Quarter Panel Push-Type Retainer, Nylon Nut, Fender Liner, Duct & Lower Moulding Push-Type Retainer, Garnish Moulding Retainer, Cowl Vent Push-Type Retainer, Trim Board Retainer, Engine Cover and Fender Liner Retainer, Screw Grommet with Sealer, Cowl Panel Vent Cap.
- ✉ Part Number: Subaru 🔷 1 #OE: 909140059; 🔷 2 #OE: 909130013; 🔷 3 #OE: 46064AE000; 🔷 4 #OE: 59130AA000; 🔷 5 #OE: 909140065; 🔷 6 #OE: 661179000; 🔷 7 #OE: 909140068; 🔷 8 #OE: 909130051; 🔷 9 #OE: 909130146; 🔷 10 #OE: 909140063; 🔷 11 #OE: 909130115; 🔷 12 #OE: 909130067; 🔷 13 #OE: 909130074; 🔷 14 #OE: 91084AA010; 🔷 15 #OE: 909140055; 🔷 16 #OE: 91486KJ010, 91486-FL020; 🔷 17 #OE: 57728AC090; 🔷 18 #OE: 909140007.
- ☺ Please Check the Part Number and Installation Position Information on the Picture Before Purchase.
- HIGH QUALITY: The retainer clips are made of high quality Black Nylon, Meet or Exceed OEM Specification, would not break or crack easily during use.
- WIDE APPLICATION: Widely used for side skirt, bumper, car fender, door trim panel, interior trim panel and various trim panels, can be used to fix a variety of automobile structures.
- Bumper Engine Cover Fender & Grille Push-Type Retainer Clip: Head Diameter: 21mm, Stem Length: 15mm, Fits into 10mm Hole. Be suitable for Subaru Baja, Forester, Impreza, Legacy, Outback & Tribeca 2000 – On. OEM: 90914-0007.
- Fender Liners Clips: Top Head Diameter: 12.8mm, Bottom Head Diameter: 19.8mm, Total Length: 21.2mm, Stem Length: 12.2mm, Stem Diameter: 7.8mm. Be suitable for Subaru B9, Forester, Legacy, Outback & Tribeca 2005 - On. OEM: 90913-0067.
- Front Bumper Clips: Head Diameter: 20mm, Stem Length: 9mm, Fits Into 7mm Hole. Retainer for Subaru Impreza, Legacy, Outback & Tribeca 2011 - 2005. OEM: 90914-0051.
- Universal fit kit - Great assortment push retainer kit with 12 popular size, fitting for door trim, radiator shield yoke, fender, bumper and splash shield retainer’s replacement for Ford, GM, Chrysler, Toyota, Honda and more..Note : If the size of the earbud tips does not match the size of your ear canals or the headset is not worn properly in your ears, you may not obtain the correct sound qualities or call performance. Change the earbud tips to ones that fit more snugly in your ear
- Save time and money - You can find 240PCS automotive push type retainer kit in the box and no need to go to auto parts store to look for different fasteners. You can remove the old clips using free fastener remover.
- High quality - High quality material with heavy-duty construction for durability, this push type retainers set would not break or crack easily during use.
- Most common sizes - Don not worry about lost or damaged body fasteners. All the necessary retainers for exact replacement of old and broken retainer.
- Easy storage - Comes with a plastic box with 12 compartments for organized storage. Compact size, convenient to store or carry with in your car.
This product presentation was made with AAWP plugin.