Accessory Installation Guide
| CROSSTREK TRAILER HITCH – warning card
L101SFL002 | L101SFL002 |
Installation Instructions
PART NUMBER: L101SFL002, L101SFL003
CROSSTREK TRAILER HITCH
This card should be stored in the vehicle glove box and handed over with the vehicle if sold.
NOTICE:
Electric Trailer Brakes: Customers towing over 1,000 lbs and using a trailer with electric brakes must purchase and install an electric brake controller and harness. The electric brake controller and harness are not available from Subaru
.
- Do not drill, cut, weld or otherwise modify the Trailer Hitch.
- If Trailer Hitch is removed, a bumper beam MUST be reinstalled. Failure to reinstall a bumper beam after removal of the trailer hitch will negatively affect vehicle rear crash performance. Please contact your SUBARU dealer.
- When a Trailer Hitch is installed, it is not possible to install the rear towing hook.
- Never exceed the maximum towing capacity and maximum tongue load. It could cause personal injury and/or vehicle damage.
- When towing, total vehicle weight must not exceed the Gross Vehicle Weight Rating (GVWR). Also the load distribution on each axle must not exceed the Gross Axle Weight Rating (GAWR). The GVWR and GAWR for your vehicle can be found on the “Certification label” which is located on the left side center pillar of the vehicle.
- A 10 amp fuse for the wiring harness is located in the rear cargo area near spare tire. CAUTION: Only use a 10 amp replacement fuse. Never use a higher rated fuse.
- After the first 600 miles, please consult with Subaru dealer to recheck the tightness of trailer hitch bolts and nuts.
- For models equipped with BSD (Blind Spot Detection) and RCTA (Rear Cross Traffic Alert) driving support systems, when towing a trailer press BSD/RCTA OFF switch to deactivate the systems. The system may not operate properly due to blocked radar waves. For details about BSD/RCTA OFF switch, refer to the owner’s manual “BSD/RCTA OFF switch”.
- For models equipped with RAB (Reverse Automatic Braking) system, please consult with SUBARU dealer when towing a trailer.
- For further information, read vehicle owner’s manual or consult your dealer or dealer’s service department.
- Subaru accepts no liability for product defects caused by incorrect use
Issue 04 – 08/18/20
L101SFL002
- Dependable Strength: Stringently tested to SAE J684 standards, the hitch has a weight capacity of 3,500 pounds gross trailer weight and 350 pounds tongue weight
- Corrosion Resistant: Finished with CURT's unique co-curing process; Each hitch is dipped in a liquid A-coat for rust prevention, inside and out, and then co-cured in a durable black powder coat finish for maximum rust, chip and UV resistance
- Vehicle Compatibility: Each CURT class 3 hitch is engineered to fit on a specific vehicle; This provides the best possible fit and easiest installation; Fits 2020-2025 Legacy & Outback
- Warranty: Covered by CURT's limited lifetime warranty to give you confidence in each adventure, season after season
- Made in USA: CURT custom-fit receiver hitches are made in the USA to ensure quality from design to finish (may include imported hardware)
- Application: This class 3 trailer tow hitch receiver is compatible with 2014 2015 2016 2017 2018 Subaru Forester all models
- Function: After installing the towing receiver device on your vehicle, it can bear the weight of the trailer and the cargo, ensuring that the towing vehicle can stably pull the load during driving
- Load-bearing Capacity: Class 3 trailer hitch is rated for up to 3,500 lbs. Tongue weight is rated for up to 525 lbs. Made of steel, it is solid and not easy to deform. The black powder coating effectively avoids rust and wear caused by external conditions, ensuring stable performance over a long time
- Installation: Install with screws, professional installation is recommended
- Package: Package includes 1 x trailer tow hitch receiver, installation hardware and assemble manual
- [Vehicle Fitment]: 2 inch trailer hitch fit for Subaru Ascent All Styles 2019 2020 2021 2022 2023 2024 2025 2026 (You can download the instruction manual below or contact us)
- [Standard Fit]: 2" rear towing hitch receiver, able to accept virtually any 2-inch x 2-inch shank, including a trailer hitch ball mount, tow hook, cargo carriers, bike carrier, weight distribution or other receiver hitch accessories
- [High Strength]: Gross Trailer Weight : 5000 LBS; Tongue Weight: 750 LBS; (limited to lowest-rated towing component)
- [Rust-Resistant&Heavy Duty]: Rugged construction- heavy duty steel construction thick welds for superior strength built for long lasting durability and rust-resistant, black powder coated for long lasting corrosion resistance
- [Warranty]: maXpeedingrods warrants its products against manufacturing defects under normal use for 1 year (since the date of purchase), and lifetime technical support and customer service
- DEPENDABLE STRENGTH — This trailer hitch is rated for 3,500 lbs. gross trailer weight and 525 lbs. tongue weight (limited to lowest-rated towing component)
- VERSATILE DESIGN — This class 3 hitch equips your vehicle with a standard 2-inch x 2-inch hitch receiver (not compatible with vertical hanging bikes / bike racks that require the bikes to be hung / mounted vertically)
- FULLY TESTED — Every CURT class 3 trailer hitch design is tested in real-world, on-vehicle conditions at our Detroit engineering facility. Aftermarket hitches are tested according to SAE J684 standards for the utmost safety while hauling
- RUST, CHIP, UV-RESISTANT — This tow hitch is protected with a unique dual-coat finish of rust-resistant liquid A-coat and highly durable black powder coat. The two finishes are co-cured together for exceptional resistance to rust, chipping and UV rays
- EASY TO INSTALL — This hitch offers a custom, factory fit on select model years of the Subaru Crosstrek
- Custom Fit For 2010‑2019 Subaru Outback: This Class 3 Trailer Hitch 2-Inch Receiver is precisely engineered for 2010‑2019 Subaru Outback (Except Sport Model), perfect fit and seamless integration. Note: Be sure to verify that your model fits
- Heavy-Duty Class III Towing Capacity: Built to handle serious towing tasks, this Tow Hitch is rated at 4,000 lbs. gross trailer weight and 600 lbs. tongue weight. Whether you’re hauling a boat, camper, utility trailer, or snowmobile hauler, this hitch provides the strength and confidence you need for every adventure
- Versatile 2-Inch Square Receiver: The standard 2 Inch Square Receiver opens up endless utility. Use it with tow hooks for towing, bike racks for weekend adventures, cargo racks for extra storage, spare tire holders for overlanding, will added convenience. This Tow Hitch transforms your SUV into a true multi‑purpose vehicle.
- Durable & Corrosion-Resistant Finish: Protected by a high‑quality black powder coat finish, this hitch resists rust, chipping, and road salt corrosion. The durable coating ensures long‑lasting appearance and performance, even in harsh weather conditions.
- Bolt-On Installation: Designed for an easy installation - simply bolt the hitch to the existing mounting points using the included hardware. For a secure and safe fit, tighten all factory bolts to 42 ft‑lbs as specified. All necessary components are included; no welding or specialized tools are required.
SEOCONTENT-START
Issue 04 – 08/18/20 PART NUMBER: L101SFL002, L101SFL003 CROSSTREK TRAILER HITCH This card should be stored in the vehicle glove box and handed over with the vehicle if sold.NOTICE:Electric Trailer Brakes: Customers towing over 1,000 lbs and using a trailer with electric brakes must purchase and install an electric brake controller and harness. The electric brake controller and harness are not available from Subaru. 1. Do not drill, cut, weld or otherwise modify the Trailer Hitch.2. If Trailer Hitch is removed, a bumper beam MUST be reinstalled. Failure to reinstall a bumper beam after removal of the trailer hitch will negatively affect vehicle rear crash performance. Please contact your SUBARU dealer. 3. When a Trailer Hitch is installed, it is not possible to install the rear towing hook.4. Never exceed the maximum towing capacity and maximum tongue load. It could cause personal injury and/or vehicle damage. 5. When towing, total vehicle weight must not exceed the Gross Vehicle Weight Rating (GVWR). Also the load distribution on each axle must not exceed the Gross Axle Weight Rating (GAWR). The GVWR and GAWR for your vehicle can be found on the “Certification label” which is located on the left side center pillar of the vehicle.6. A 10 amp fuse for the wiring harness is located in the rear cargo area near spare tire. CAUTION: Only use a 10 amp replacement fuse. Never use a higher rated fuse.7. After the first 600 miles, please consult with Subaru dealer to recheck the tightness of trailer hitch bolts and nuts.8. For models equipped with BSD (Blind Spot Detection) and RCTA (Rear Cross Traffic Alert) driving support systems, when towing a trailer press BSD/RCTA OFF switch to deactivate the systems. The system may not operate properly due to blocked radar waves. For details about BSD/RCTA OFF switch, refer to the owner’s manual “BSD/RCTA OFF switch”.9. For models equipped with RAB (Reverse Automatic Braking) system, please consult with SUBARU dealer when towing a trailer.10. For further information, read vehicle owner’s manual or consult your dealer or dealer’s service department.11. Subaru accepts no liability for product defects caused by incorrect use
**************************************************************************************************************
SEOCONTENT-END
This product presentation was made with AAWP plugin.