NHTSA ID Number: 10188183
Manufacturer Communication Number: 14-27-21
Summary
This bulletin announces the upcoming issuance to all retailers of an essential tool update kit for the Engine Support Assembly Kit #J-50135-A.
NUMBER: 14-27-21
DATE: 02/17/21
| APPLICABILITY: | 2020-21MY Legacy and Outback 2019-21MY Forester 2017-21MY Impreza 2019-21MY Ascent |
| SUBJECT: | New Engine Support Assembly Retaining Nuts |
INTRODUCTION:
This Service Information Bulletin announces the upcoming issuance to all retailers of an essential tool update kit for the Engine Support Assembly Kit #J-50135-A. The update kit is being released as SOA321132. Available separately as J-28467-125A, the kit consists of 6 (six) new (M10 x 1.25) Strut Support Nuts along with 6 new thumb screws to be used to supplement the 6 previously provided M8 x 1.25 versions (J-28467-33A) when required. These new nuts have also been added to new Engine Support Assembly Kits to support newer vehicles equipped with M10 x 1.25 strut mounting studs. The updated support nuts are shipped in quantities of 6 along with 6 new thumb screws.
| J-28467-33A (CURRENT)
Thread Size: M8 x 1.25 | J-28467-125A (NEW)
Thread Size: M10 x 1.25 |
SERVICE PROCEDURE / INFORMATION:
REMINDER: Customer satisfaction and retention starts with performing quality repairs.
The service procedures for using the Engine Support Assembly remain unchanged. Always refer to the applicable Service Manual and review the full procedure, instructions and precautions. The Service Manual procedures contain information critical to performing an effective repair the first time, every time. This includes but is not limited to important SAFETY precautions and required processes needed for a complete and lasting repair.
The new support nuts, 3 (three) per side along with the thumb screws will mount the existing strut supports (J-28467-5A) in the same way as with the current 8mm nuts.
CAUTION: Always use all 6 support nuts and thumb screws specific to the vehicle being repaired every time the strut supports are installed. Confirm all are installed correctly and properly tightened whenever in use.
15 Affected Products
Vehicles
| MAKE | MODEL | YEAR |
SUBARU | ASCENT | 2019-2021 |
| SUBARU | FORESTER | 2019-2021 |
| SUBARU | IMPREZA | 2017-2021 |
| SUBARU | LEGACY | 2020-2021 |
| SUBARU | OUTBACK | 2020-2021 |
1 Associated Document
Manufacturer Communications
NUMBER: 14-27-21
DATE: 02/17/21
MC-10188183-0001.pdf 1211.309KB
- DURABLE AND ROBUST: Constructed with thickened high-strength steel and a double-beam structure, it bears a load of up to 1,100 pounds; The thickened rust-proof coating effectively resists oil contamination and corrosion, ensuring long-lasting use
- WIDE COMPATIBILITY: Equipped with an ultra-wide 57-inch beam, and an adjustable triangular base, which allows effortless mounting on sedans, SUVs, sports cars, and light trucks; Compatible with V6/V8 engines, eliminating tool compatibility issues
- PRECISION ADJUSTMENT: Dual precision threaded hooks with continuous lifting range from 0 to 7.9 inches; 2 bases can also be changed from 21 to 57 inches, so it applies to vehicles that width is less than 57 inches; One person can handle it with ease
- PREMIUM FEATURES: Two heavy-duty iron chains securely hold the motor, making engine mounting easier; The non-slip thickened rubber feet on the bottom of the triangular base can effectively reduce noise when moving and prevent scratches on the car
- EASY TO USE: No complex tools required; Simply adjust the base and secure the chain to start repairs quickly; This hoist is perfect for auto repair technicians, DIY car owners, and any shop or garage looking for a reliable lifting solution
- Performance Engine Support Bar: Holding capacity: 1100 lbs. This engine support bar can precisely position and support the engine while working on the transmission or holds the transmission in place while removing the engine for rebuilding.
- Rotating Lift Pile: The lifting height of 2 rotating hoists on the engine holder bar can be adjusted from 0 to 7.87 inches. Turn the handle to raise or lower the motor at the proper height according to your requirements.
- Engine Binding Chain: It comes with double strong iron chains that ensure the secure landing of the motor. The bold chains are tightly welded and don't break.
- Adjustable Working Range: Equipped with a knob and stable triangular base on each side. The range between the 2 bases can be adjusted; you can place them in the appropriate position. The width of the beam is 59.06 in, so it applies to vehicles that width is less than 59.06 in.
- Dual Steel Bar: The engine support bar is made of heavy-duty steel with a protective powder coat finish, high rigidity, and resistance. The dual steel bar build means this engine bar can support your engine or transmission through long rebuilds.
- Makes removal of transaxle easy by supporting engine of front wheel drive vehicles
- Support Arm provides three point support for off-center loads
- Includes 1/8-Inch braided steel cables and 14-Inch adjustable hooks
- Capacity, 700-Pound, Weight, 21-Pound
- Min: 31-Inch and Max, 64-Inch
- Two 14 inches adjustable hook screws
- Width expands from 38 inches to a full 61 inches
- 700 pounds capacity adjustable transverse bar
- Two 38 inches braided steel cables 1/8 inch diameter included
- Country of Origin:China
- Package length:40.5"
- Package width:6.0"
- Package height:5.0"
SEOCONTENT-START
Bulletin Number: 4-27-20; Date: 02/17/21 Page 1 of 2 Continued… CAUTION: VEHICLE SERVICING PERFORMED BY UNTRAINED PERSONS COULD RESULT IN SERIOUS INJURY TO THOSE PERSONS OR TO OTHERS. Subaru Service Bulletins are intended for use by professional technicians ONLY. They are written to inform those technicians of conditions that may occur in some vehicles, or to provide information that could assist in the proper servicing of the vehicle. Properly trained technicians have the equipment, tools, safety instructions, and know-how to do the job correctly and safely. If a condition is described, DO NOT assume that this Service Bulletin applies to your vehicle, or that your vehicle will have that condition. Subaru of America, Inc. is ISO 14001 Compliant ISO 14001 is the international standard for excellence in Environmental Management Systems. Please recycle or dispose of automotive products in a manner that is friendly to our environment and in accordance with all local, state and federal laws and regulations. NUMBER: 14-27-21 DATE: 02/17/21 APPLICABILITY: 2020-21MY Legacy and Outback 2019-21MY Forester 2017-21MY Impreza 2019-21MY Ascent SUBJECT: New Engine Support Assembly Retaining Nuts INTRODUCTION: This Service Information Bulletin announces the upcoming issuance to all retailers of an essential tool update kit for the Engine Support Assembly Kit #J-50135-A. The update kit is being released as SOA321132. Available separately as J-28467-125A, the kit consists of 6 (six) new (M10 x 1.25) Strut Support Nuts along with 6 new thumb screws to be used to supplement the 6 previously provided M8 x 1.25 versions (J-28467-33A) when required. These new nuts have also been added to new Engine Support Assembly Kits to support newer vehicles equipped with M10 x 1.25 strut mounting studs. The updated support nuts are shipped in quantities of 6 along with 6 new thumb screws. J-28467-33A (CURRENT) Thread Size: M8 x 1.25 Thread Size: M10 x 1.25 J-28467-125A (NEW) SERVICE INFORMATION BULLETIN ATTENTION: GENERAL MANAGER q PARTS MANAGER q CLAIMS PERSONNEL q SERVICE MANAGER q IMPORTANT – All Service Personnel Should Read and Initial in the boxes provided, right. © 2020 Subaru of America, Inc. All rights reserved. Bulletin Number: 4-27-20; Date: 02/17/21 Page 2 of 2 SERVICE PROCEDURE / INFORMATION: REMINDER: Customer satisfaction and retention starts with performing quality repairs. The service procedures for using the Engine Support Assembly remain unchanged. Always refer to the applicable Service Manual and review the full procedure, instructions and precautions. The Service Manual procedures contain information critical to performing an effective repair the first time, every time. This includes but is not limited to important SAFETY precautions and required processes needed for a complete and lasting repair. The new support nuts, 3 (three) per side along with the thumb screws will mount the existing strut supports (J-28467-5A) in the same way as with the current 8mm nuts. Top View CAUTION: Always use all 6 support nuts and thumb screws specific to the vehicle being repaired every time the strut supports are installed. Confirm all are installed correctly and properly tightened whenever in use. IMPORTANT REMINDERS: • SOA strongly discourages the printing and/or local storage of service information as previously released information and electronic publications may be updated at any time. • Always check for any open recalls or campaigns anytime a vehicle is in for servicing. • Always refer to STIS for the latest service information before performing any repairs.
**************************************************************************************************************
SEOCONTENT-END
This product presentation was made with AAWP plugin.