H7110AL100 – AC Power Outlet Kit – 2017 Subaru Legacy & Outback

SEOCONTENT-START

̶ 1 ̶ Fuji Heavy Industries Ltd. H7110-AL100-A1 2. KIT CONTENTS ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑫ ⑨ ⑩ No. ① OUTLET ② BRACKET ③ RUBBER GASKET ④ TAPPING SCREW ⑤ INVERTER ⑥ BRACKET ⑦ SCREW (M4) ⑧ HARNESS ⑨ DOUBLE SIDED TAPE ⑩ ALUMINUM TAPE ⑪ FOAM TAPE (GRAY) ⑫ TIE WRAP (150mm ) ⑬ FOAM TAPE (BLACK) ⑭ OWNERS MANUAL 111212411 10 1171 ⑪ ⑬ 1. PRE INSTALLATION / INSTALLATION OVERVIEW Part Name Q’ty Part Number Description ：H7110AL100 ：Legacy AC 120V Power Outlet AC 120V POWER OUTLET INSTALLATION INSTRUCTIONS OUTLET KIT INVERTER HARNESS H7110VA120 H7110AJ130 H7110AL110 ①,②,③,④ ⑤,⑨ ⑧ ⑭ (In the case of car without RAB) (In the case of car with RAB without Harman Kardon Audio) ̶ 2 ̶ 4. PRECAUTIONS FOR INSTALLATION 3. TOOLS REQUIRED PHILLIPS SCREWDRIVER FLAT BLADE SCREWDRIVER 10mm,14mm SOCKET WRENCH PLIERS φ24mm (15/16″) HOLE SAW φ3.5mm (1/8″) DRILL VOLT METER (or CIRCUIT TESTER) SIDE CUTTERS SCISSORS UTILITY KNIFE CENTER PUNCH CHALK MASKING TAPE ELECTRICAL TAPE TRIM REMOVAL TOOL ISOPROPYL ALCOHOL CLEANING TOWEL CAUTION Please follow the Instructions for your safety. If these Instructions are not followed. Personal injury. Vehicle damage or degraded performance of the 110V Outlet may result. CAUTION Always perform installation in a building or a room. Venlilate air to avoid exhaust gas-filled almosphere when checking aclivalion. Make sure to fully ungage and connect all wire plugs & receptacles and connectors to their individual mating parts. Use screws or other similar fasteners to secure all lead wire terminals in order to prevent connection failure and/or looseness caused by vibration or oscillation. To prevent potential damage to your vehicle during installation, use reasonable protective covers to cover the passenger compartment and body surface around the engine. Use a proper tool of correct size to tighten bolts and nuts. Fully tighten bolts and nuts with specified tightening torque as required. Inobservance of this instruction will cause a potential risk of damage to bolts and nuts. Remove the negative battery terminal before start of wiring work. With the battery kept connected, wiring work will lead to a potential risk of failure or of electric shock or inlury due to short circuit. Do not apply an excessive force to pull off a vehicle wire harness, to prevent loose connectors, disconnection and/or damage. Check that all electrical systems of your vehicle are properly operative. Back up all memories of a radio and other electrical systems, to avoid any possible loss during recovery checks after installation. When installing parts and/or removed finishers, avoid dragging or pinching wires in order to prevent a potential risk of accident, electric shock or fire due to disconnection and/or short circuit. Use appropriate cleaner or mild detergent to remove all dirt and old grease before attaching one-sided and/or double-sided tapes during installation. Tapes applied onto an unclean area cannot demonstrate desirable. If the vehicle body needs to be drilled for installation, check the positions of pipings, tanks and electrical wirings before drilling and avoid any interference or contact with them. When harnessing,follow all instructions provided in the Installation Instruction. Use reasonable bands or other similar materials to tack and secure wiring to prevent entrapment into the steering, shift lever and/or brake pedal. After removing clips and screws from your vehicle, sort them by individual components for subsequent reinstallation work to prevent use of wrong clips and screws.Use of wrong clips and screws will cause looseness and coming-off. After harnessing, check activations of all parts installed before recovery, to prevent wrong wiring. When disconnecting vehicle connectors, hold connectors (do not hold lead wires) to unlock them, to prevent disconnection in lead wires. To secure an optional GND terminal together with a vehicle GND terminal, fasten them in a correct order (bolt → vehicle GND → optional GND → body panel). Vehicle Option Check DOOR CONSOLE Fully ungaged CAUTION This product requires removal of the passenger ‘s seat. As a result of the removal of the passenger ‘s seat it will be necessary to re-calibrate the Occupant Detection System. If not properly calibrated the Occupant Detection System may not operate as designed which may result in injuries to the front seat passenger. Therefore, it is strongly recommended that the product be installed at an authorized Subaru dealer. ̶ 3 ̶ 5. INSTALLATION PROCEDURE 1. REMOVAL OF INTERIOR TRIM COMPONENTS 1 2 3 4 1-2 Removal the following components : Ornament panel-console Cover assembly-front Console box assembly Console cover (In the case of car without RAB) 1-1 Drivers Seat Removal: CAUTION 1. Before disconnecting any yellow (air bag) connectors, turn off ignition and disconnect (-) battery terminal for at least 20 seconds. 2. Be careful when working on the vehicle interior not to damage / scratch components. 3. Be careful when working to avoid injury. Seat rail bolt (Q’ty 4) 2. Disconnect electronic components under the seat. 3. Protect seat frame rail legs with towel to avoid scratching. 4. Remove seat. 【Tightening torque should read 53 N･m (5.4 kgfm, 39ft-lbs)】 Seat rail bolt (Q’ty 4) 4 1 2 3 1 1. Remove four seat rail bolts. ̶ 4 ̶ 2. REMOVAL OF INTERIOR TRIM COMPONENTS 1 2 3 4 2-2 Removal the following components : Ornament panel-console Cover assembly-front Console box assembly Console cover (In the case of car with RAB and Harman Kardon Speakers) 2-1 Passenger Seat Removal: CAUTION 1. Before disconnecting any yellow (air bag) connectors, turn off ignition and disconnect (-) battery terminal for at least 20 seconds. 2. Be careful when working on the vehicle interior not to damage / scratch components. 3. Be careful when working to avoid injury. Seat rail bolt (Q’ty 4) 2. Disconnect electronic components under the seat. 3. Protect seat frame rail legs with towel to avoid scratching. 4. Remove seat. 【Tightening torque should read 53 N･m (5.4 kgfm, 39ft-lbs)】 Seat rail bolt (Q’ty 4) 4 1 2 3 1 1. Remove four seat rail bolts. ̶ 5 ̶ Release the clips, and remove the ornament panel – console. Remove the cover assembly – front. (1) Remove the shift knob. (MT model) (2) Pull up the cover assembly – front, and release the clips. (3) Disconnect the connectors, and remove the cover assembly – front. Remove the console box assembly. (1) Remove the caps, and remove the bolts. (2) Remove the screws, disconnect the harness connector and remove the console box assembly. Remove the console cover. Disconnect negative battery terminal. Note : Some vehicle systems may need to reconfigured after battery is reconnected. See service manual. Disconnect NOTE: Shift the select lever into “N”. ̶ 6 ̶ 4. INVERTER UNIT INSTALLATION CAUTION 1. Make sure that inverter is placed in correct direction and position. 2. Vehicle must be at room temperature. 1. Cut off Double sided tape ⑨ as shown in left picture. 2. Fix the Brackets ⑥ on Inverter ⑤ with four Screws ⑦. 3. Apply the Double sided tape ⑨ (A) on the bottom of Bracket ⑥. 4. Locate position where Inverter ⑤ will be installed. 5. Pull up carpet and de-grease floor surface with Isopropyl alcohol where Inverter ⑤ will be installed. 6. Remove release liner from Double-sided tape ⑨ and apply on bottom of both Brackets ⑥. 7. Install Inverter ⑤ to center of cut area with connector facing driver. 8. Apply on the Inverter ⑤ after apply the Double sided tape ⑨ (B) on the Carpet. 3. TRIM FLOOR CARPET CAUTION 1.When cutting out the floor carpet, take care that you do not cut the vehicle harness. 2.Scraps of insulation from the floor carpet may cause the unit to become clogged, so remove all scraps after work is complete. Insulator Double sided tape position Remove insulator FRONT completely (Driver side,under seat area) 1. Apply masking tape to the floor carpet in the areas shown in the image on the left. 2. Cut out the floor carpet around the outside edge of the masking tape. 3. Lift up the floor carpet and cut out part of the insulation. Take care that there are no scraps of insulation around areas where butyl tape has been applied. (In the case of car without RAB) A B 20mm 50mm Double sided tape ⑨ Cut off Screws ⑦ Screws ⑦ Bracket ⑥ Bracket ⑥ Double sided tape ⑨ (A) Inverter ⑤ FRONT Mounting holes Double sided tape ⑨ (B) Carpet FRONT Marking tape Cuting line 120mm 140mm 50mm ̶ 7 ̶ 6. INVERTER UNIT INSTALLATION CAUTION 1. Make sure that inverter is placed in correct direction and position. 2. Vehicle must be at room temperature. 1. Cut off Double sided tape ⑨ as shown in left picture. 2. Fix the Brackets ⑥ on Inverter ⑤ with four Screws ⑦. 3. Apply the Double sided tape ⑨ (A) on the bottom of Bracket ⑥. 4. Locate position where Inverter ⑤ will be installed. 5. Pull up carpet and de-grease floor surface with Isopropyl alcohol where Inverter ⑤ will be installed. 6. Remove release liner from Double-sided tape ⑨ and apply on bottom of both Brackets ⑥. 7. Install Inverter ⑤ to center of cut area with connector facing driver. 8. Apply on the Inverter ⑤ after apply the Double sided tape ⑨ (B) on the Carpet. 5. TRIM FLOOR CARPET CAUTION 1.When cutting out the floor carpet, take care that you do not cut the vehicle harness. 2.Scraps of insulation from the floor carpet may cause the unit to become clogged, so remove all scraps after work is complete. Insulator Double sided tape position Remove insulator FRONT completely (Passenger side,under seat area) 1. Apply masking tape to the floor carpet in the areas shown in the image on the left. 2. Cut out the floor carpet around the outside edge of the masking tape. 3. Lift up the floor carpet and cut out part of the insulation. Take care that there are no scraps of insulation around areas where butyl tape has been applied. (In the case of car with RAB and Harman Kardon Speakers) A B 20mm 50mm Double sided tape ⑨ Cut off Screws ⑦ Screws ⑦ Bracket ⑥ Bracket ⑥ Double sided tape ⑨ (A) Inverter ⑤ FRONT Mounting holes Double sided tape ⑨ (B) Carpet 120mm 20mm 140mm FRONT Marking tape Cuting line ̶ 8 ̶ 7. HARNESS 1. Apply the 7 Foam tapes ⑬ as shown. 1. Route the harness to the floor carpet cutout area as shown. 2. Connect Harness ⑧ to the Inverter ⑤. 3. Apply the 10 Aluminum tapes ⑩ and Tie wrap ⑫ to secure as shown. CAUTION Be sure to route harness away from shap edges. Harness ⑧ Foam tape (Black) ⑬ Foam tape (Black) ⑬ 8. WIRE HARNESS INSTALLATION Front Aluminum tape ⑩ Inverter ⑤ Aluminum tape ⑩ Aluminum tape ⑩ Aluminum tape ⑩ Aluminum tape ⑩ Outlet connector Tie wraps ⑫ [with Vehicle harness] Vehicle harness Harness ⑧ Bundle up the excess harness. Vehicle bracket 10mm 20mm (In the case of car without RAB) ̶ 9 ̶ 1. Route the harness to the floor carpet cutout area as shown. 2. Connect Harness ⑧ to the Inverter ⑤. 3. Apply the 10 Aluminum tapes ⑩ and Tie wrap ⑫ to secure as shown. CAUTION Be sure to route harness away from shap edges. (In the case of car with RAB and Harman Kardon Speakers) 9. WIRE HARNESS INSTALLATION Front Outlet connector Harness ⑧ Tie wraps ⑫ [with Vehicle harness] Vehicle harness Inverter ⑤ Aluminum tape ⑩ Aluminum tape ⑩ Aluminum tape ⑩ Aluminum tape ⑩ Aluminum tape ⑩ ̶ 10 ̶ 1. After disconnecting vehicle harness from 12V Power outlet, connect the Harness ⑧ connector as shown. 10. CONNECT HARNESS TO VEHICLE HARNESS 2. After all connections are made, overwrap in Foam tape ⑪ as shown. Vehicle Power-socket connector Harness ⑧ Foam tape ⑪ Foam tape ⑪ to Vehicle Power-socket Harness ⑧ ̶ 11 ̶ φ3.5mm (1/8″) Holes Hole sawφ24mm (15/16″) Drilling instruction 1. Drill three φ3.5mm (1/8″) holes and then enlarge center hole φ24mm (15/16″) with hole saw. 13. OUTLET MOUNTING HOLE PROCESSING 11. DRIVER SEAT INSTALL CAUTION ・Front (bolt A) : Washer diameter 22mm (0.87 in) ・Rear (bolt B) : Washer diameter 26mm (1.02 in) ・Tightening torque : Front seat assembly : 53N･m (5.4 kgf-m, 39.1 ft-lb) (In the case of car without RAB) (1) (2) (3) (4) 22mm (0.87 in) B 26mm (1.02 in) A Center console back panel φ3.5mm φ24mm Marking center 12. PASSENGER SEAT INSTALL CAUTION ・Front (bolt A) : Washer diameter 22mm (0.87 in) ・Rear (bolt B) : Washer diameter 26mm (1.02 in) ・Tightening torque : Front seat assembly : 53N･m (5.4 kgf-m, 39.1 ft-lb) (In the case of car with RAB and Harman Kardon Speakers) (1) (2) (3) (4) 22mm (0.87 in) B 26mm (1.02 in) A ̶ 12 ̶ 14. OUTLET INSTALLATION 1. Fit Rubber gascket ③ onto Outlet ① and position Outlet ① over holes drilled from the above step. 2. Place Bracket ② on the other side of the center console and mount the Outlet ① with the two supplied self Tapping screws ④. 3. Place console back in position and connect female receptacle connectors to back of Outlet ① as shown and verify that the rubber caps are firmly secured. CAUTION When connecting the female receptacle connectors to the back of the Outlet. it does not matter which wire (color) is connected to each terminal. Tapping screws ④ Outlet ① Rubber gasket ③ Bracket ② Console cover Holes Outlet ① Interior harness Outlet connectors Thick Thin ̶ 13 ̶ * The volt meter voltage reading may be less than 110V AC depending on tester types. * Output waveform is rectangular. * When the battery voltage is low, the voltage of outlet may not maintain the rated 70V AC or more. Outlet ① Check that voltage* of Outlet is 70V AC or more. Start check procedure. Connect negative terminal of battery. [ stud type : 5.5ftl bs (66in lbs) ] Ignition switch is turned to “ON” position. Yes No Complete check procedure. Perform Troubleshooting A. (Next page) VOLT METER 15. CHECK THE OPERATION CAUTION Verify that all yellow (Air bag) connectors are connected firmly. 1. Check that all wiring and attaching points are correct. 2. Be careful not to pinch, strain, or crush wires during reassembly. 3. Be careful not to damage vehicle parts during reassembly. 1. POST-INSTALLATION CHECK 1. Use a volt meter to measure voltage. Strictly keep the volt meter set at range of “250V AC or more” for measuring any power supply of 110V AC or more. 2. CHECK VOLTAGE ̶ 14 ̶ Checking Procedure A 4 2 1 8 7 6 5 3 (Female) Checking connectors of the main body Check the continuity and/or voltage of connector terminals connected to the main body (with all other connectors still connected). Terminal Test parameter Conditions Ignition key should be changed from OFF to ACC or ON position. All the time All the time Tester + Tester – Tolerance When outside the tolerance 1 4 Voltage 3 Ground Continuity 7 Ground Continuity 0V to 10V or more No continuity No continuity Perform Checking Procedure C Replace the harness with new one. Replace the harness with new one. A Everything is within the tolerance. Are Female Receptacles B and C connected? Is the output voltage of Outlet * 70V AC or more? Yes No Connect it. No Replace Inverter with new one. Is the output voltage of Outlet 70V AC or more? Yes Yes (The original inverter was defective.) Proceed to next step. Replace harness with new one since it is defective. No This section describes the inspection procedure for malfunction which may take place after installation is completed. Use a circuit tester for continuity and/or voltage testing. Checking Procedure B Is the wire tap connected at the correct position (E)? Yes No Connect it. Connect the wire tap at the correct position. No Yes End of inspection Inspect the Cigerette lighter fuse in the fuse box. Is the connecting procedure of the wire tap (page 17) correct? Is the vehicle connector connected? No Connect it. Does the internal relay of the cabin harness make “click” sound when the ignition key is turned to “ON” position? Yes No Did the connector terminals serve as the reference? Replace the harness because it is defective. Yes Yes No * The voltmeter voltage reading may be less than 115V AC depending on tester types. * Output waveform is rectangular. * When the battery voltage is being decreased, the voltage of outlet might not keep the rated 70V AC or more. 16. TROUBLESHOOTING ̶ 15 ̶ 18. CIRCUIT DIAGRAM 17. RE-ASSEMBLY 1. Be careful to avoid pinching the harness or any vehicle harness , or damaging any vehicle parts when reassembling parts and/or components. After the check procedure is completed, re-assemble all removed vehicle parts and components paying attention not to damage them. Inverter 0.5O 1.25B 0.5G Outlet 1.25R 20A 1 1 AC1 AC2 1 2 3 4 5 6 7 8 ACC INPUT NC AC OUTPUT1 GND NC NC AC OUTPUT2 NC ＋ － 2 1 CIGARETTE LIGHTER ＊ 1 7 ＊ ＊ 4 3 ＊ 1 (Female) (Female Receptacle) (Female) (Vehicle’s 2P connector) A A C B C B D D ACC CAUTION 0.5W 0.5B AC output power ( max continuous ) AC output surge capacity ( peak ) AC output voltage ( nominal ) AC output frequency AC input waveform Low input shutdown voltage ( inverter ) 100W 120W 120V 60 Hz Modified Sine DC11V 1 2

**************************************************************************************************************

**************************************************************************************************************

SEOCONTENT-END