NHTSA ID Number: 10232847
Manufacturer Communication Number: 078114
Summary
Revised Rear Combination Lamp to Prevent Condensation
NUMBER: 07-81-14
DATE: 02/03/14
| APPLICABILITY: | 2014MY XV Crosstrek Hybrid (HEV) |
|---|---|
| SUBJECT: | Revised Rear Combination Lamp to Prevent Condensation |
INTRODUCTION
A revised rear combination lamp assembly has been developed which utilizes additional sealing material in four areas designed to prevent condensation from occurring on the inside of the housing. When performing this procedure, replace BOTH rear combination lamps at the same time.
COUNTERMEASURE IN PRODUCTION
The new combination lamps were incorporated into production December 12, 2013 starting with VIN E*251655.
PART INFORMATION
| PART NAME | NEW PART NUMBER | LOCATION |
|---|---|---|
| Lens & Body Compl. | 84912FJ280 | Right |
| 84912FJ290 | Left |
SERVICE PROCEDURE / INFORMATION
- Remove the two 10mm retaining screws then wiggle / slide the lamp assembly straight back toward the rear of the vehicle to release it from the body side retaining clip and alignment pins as shown in the photos below.
NOTE: No interior trim removal is necessary.
- Disconnect the lamp harness to body harness connector.
- Once the combination lamp assembly is removed, remove all the bulb sockets from the housing as shown below and unclip the harness connector from the mounting bracket.
- Using a plastic trim tool, CAREFULLY release the LED harness connector retaining tab as shown below.
NOTE: Always use caution and avoid touching the bulbs. If touched, oil will transfer from your fingers and likely cause premature bulb failure. Use rubbing alcohol to clean any bulbs which have been touched before reinstallation.
- The wiring harness assembly must be transferred over to the replacement combination lamp.
- NOTE: To properly position the harness into its retaining groove in the housing, the new additional sealing material just above the harness connector will need to be partially removed for access as shown in the photo sequence below. Do not disturb the material any more than necessary to properly position the harness.
- CAREFULLY lift/ peel the material up then, once the harness is tucked fully into the groove using a plastic trim tool, push the material back down into place.
- Tuck the LED harness past the sealing material into its corresponding retaining groove.
- Reinstall all the bulb sockets, reconnect the vehicle harness then refit the combination lamp making sure the slot in the side of the housing engages the retaining clip on the body properly.
- Start the vehicle and verify all the combination lamp functions operate properly.
- Torque the mounting bolts to 7.5 Nm (5.5 ft-lb) to complete the procedure.
1 Affected Product
Vehicle
| MAKE | MODEL | YEAR |
| SUBARU | XV CROSSTREK HYBRID | 2014 |
1 Associated Document
Manufacturer Communications
NUMBER: 07-81-14
DATE: 02/03/14
MC-10232847-9999.pdf 1924.007KB
NHTSA ID Number: 10067836
Manufacturer Communication Number: 07-81-14
Summary
A REVISED REAR COMBINATION LAMP ASSEMBLY HAS BEEN DEVELOPED WHICH UTILIZES ADDITIONAL SEALING MATERIAL IN FOUR AREAS DESIGNED TO PREVENT CONDENSATION FROM OCCURRING ON THE INSIDE OF THE HOUSING.WHEN PERFORMING THIS PROCEDURE, REPLACE BOTH REAR COMBINATION LAMPS AT THE SAME TIME.
1 Associated Document
Service Bulletin Document
NUMBER: 07-81-14
DATE: 02/03/14
SB-10067836-0699.pdf 585.852KB
- Lights Dim Over Time, Replace In Pairs: Your lights are a pair, one is never turned on without the other. If one bulb burns out, the other isn't far behind
- Verify fitment: Navigate to the Amazon Confirmed Fit tool at the top of the page (desktop) or under the images (mobile). Plug in your vehicle info and check the bulb fitment location to ensure this product will work for your needs
- Easy To Replace: Sylvania Long Life miniature bulbs are easy to install and show instant results
- Low Maintenance And High Durability: Designed for durability, greater safety, and lower maintenance by the leading supplier of automotive lighting
- Longer Life Than Most Standard Bulbs: Long Life bulbs perform twice as long as any other standard miniature bulbs
- LIGHTS DIM OVER TIME, REPLACE IN PAIRS: Your lights are a pair, one is never turned on without the other. If one bulb burns out, the other isn't far behind.
- EASY TO REPLACE: Sylvania Long Life miniature bulbs are easy to install and show instant results.
- LOW MAINTENANCE AND HIGH DURABILITY: Designed for durability, greater safety, and lower maintenance by the leading supplier of automotive lighting.
- LONGER LIFE THAN MOST STANDARD BULBS: Long Life bulbs perform twice as long as any other standard miniature bulbs.
- THE SYLVANIA STANDARD OF QUALITY: With 100+ years in business, Sylvania is the world leader in automotive lighting for Original Equipment Manufacturers (OEMs) and the aftermarket.
- Set of 2 Bulbs with 54SMD 3014 & 3SMD 3030 high brightness chips per bulb, Working Voltage: 12v-24v.
- Fits: 3056 3057 3057K 3057LL 3155 3157 3157K 3157NA 3156NA 3156A 3156 3156K 3357KNA 3357LL 3457 4057 4057K 4114 4114K 4157 4157K 4157NA etc. Easy installation, plug and play.
- Application: Back Up Reverse Lights, Tail Brake Lights, Turn Signal Lights, Tail Lights, Parking Lights, Side Marker Lights, Daytime Running Lights etc. Load resistor or flash relay might be needed to prevent the hyper flash or system error.
- Advantage: Non-polarity design, more than 300% brighter than original halogen bulb, full Aluminum Housing with Projection lens for Maximum Light output and better heat distribution, built in Constant Current IC for Longer life span & Low Power Consumption.
- Please double check owners manual or original bulb number to confirm before placing an order. Any other problem please feel free to contact us, we are always here to satisfy of you. (New design launched in 2019, US Patent number US-D908272-S)
- Excellent Lighting: With a color temperature of 3000K and a brightness of 54lm, this 3157 taillight bulb provides even and stable light, significantly improving visibility when braking. Its 360-degree lighting effect ensures that the surrounding environment is fully illuminated, and the non-flickering light effectively improves night driving safety
- Quartz Glass Material: High temperature resistant, impact resistant, compact in size, with good light transmission and light gathering effect, and featuring a waterproof design that adapts to humid environments for long-term stable lighting, this rear turn signal bulb made of quartz glass meets diversified needs
- Product Parameters: Rated at 12V, with 21W power, 3000K color temperature, 54lm lumen, and a service time of about 500 hours, this break light bulb replacement model 3157 comes in a pack of 10 for daily use. Please verify compatibility with your model before purchasing
- Non-destructive Installation: Designed with a standard plug for easy installation, causing no CAN-Bus error codes or bulb flickering, and preserving the car’s original control circuit system, this 3157 halogen bulb ensures stable operation with its good thermal conductivity and heat dissipation
- Widely Universal: Used as a tail light, side marker light, brake light and instrument light for most types of vehicles such as cars, SUVs, trucks and more, this automotive brake bulb has a wide range of applications and is an ideal universal automotive lighting accessory
- Lights Dim Over Time, Replace In Pairs: Your lights are a pair, one is never turned on without the other. If one bulb burns out, the other isn't far behind.
- Easy To Replace: Sylvania Long Life miniature bulbs are easy to install and show instant results.
- Low Maintenance And High Durability: Designed for durability, greater safety, and lower maintenance by the leading supplier of automotive lighting.
- Longer Life Than Most Standard Bulbs: Long Life bulbs perform twice as long as any other standard miniature bulbs.
- The Sylvania Standard Of Quality: With over 100 years in business, Sylvania is the world leader in automotive lighting for Original Equipment Manufacturers (OEMs) and the aftermarket.
SEOCONTENT-START
Bulletin Number: 07-81-14; Date: 02/03/14 Page 1 INTRODUCTION A revised rear combination lamp assembly has been developed which utilizes additional sealing material in four areas designed to prevent condensation from occurring on the inside of the housing. When performing this procedure, replace BOTH rear combination lamps at the same time. COUNTERMEASURE IN PRODUCTION The new combination lamps were incorporated into production December 12, 2013 starting with VIN E*251655. PART INFORMATION PART NAME NEW PART NUMBER LOCATION Lens & Body Compl. 84912FJ280 Right 84912FJ290 Left NUMBER: 07-81-14 DATE: 02/03/14 APPLICABILITY: 2014MY XV Crosstrek Hybrid (HEV) SUBJECT: Revised Rear Combination Lamp to Prevent Condensation SERVICE BULLETIN ATTENTION: GENERAL MANAGER q PARTS MANAGER q CLAIMS PERSONNEL q SERVICE MANAGER q IMPORTANT – All Service Personnel Should Read and Initial in the boxes provided, right. Continued… CAUTION: VEHICLE SERVICING PERFORMED BY UNTRAINED PERSONS COULD RESULT IN SERIOUS INJURY TO THOSE PERSONS OR TO OTHERS. Subaru Service Bulletins are intended for use by professional technicians ONLY. They are written to inform those technicians of conditions that may occur in some vehicles, or to provide information that could assist in the proper servicing of the vehicle. Properly trained technicians have the equipment, tools, safety instructions, and know-how to do the job correctly and safely. If a condition is described, DO NOT assume that this Service Bulletin applies to your vehicle, or that your vehicle will have that condition. SUBARU OF AMERICA, INC. IS “ISO 14001 COMPLIANT” The international standard for excellence in Environmental Management Systems. Please recycle or dispose of automotive products in a manner that is friendly to our environment and in accordance with all local, state and federal laws and regulations. Additional Sealing Material Bulletin Number: 07-81-14; Date: 02/03/14 Page 2 SERVICE PROCEDURE / INFORMATION • Remove the two 10mm retaining screws then wiggle / slide the lamp assembly straight back toward the rear of the vehicle to release it from the body side retaining clip and alignment pins as shown in the photos below. NOTE: No interior trim removal is necessary. • Disconnect the lamp harness to body harness connector. • Once the combination lamp assembly is removed, remove all the bulb sockets from the housing as shown below and unclip the harness connector from the mounting bracket. • Using a plastic trim tool, CAREFULLY release the LED harness connector retaining tab as shown below. Continued… Retaining Screws Bulletin Number: 07-81-14; Date: 02/03/14 Page 3 NOTE: Always use caution and avoid touching the bulbs. If touched, oil will transfer from your fingers and likely cause premature bulb failure. Use rubbing alcohol to clean any bulbs which have been touched before reinstallation. • The wiring harness assembly must be transferred over to the replacement combination lamp. • NOTE: To properly position the harness into its retaining groove in the housing, the new additional sealing material just above the harness connector will need to be partially removed for access as shown in the photo sequence below. Do not disturb the material any more than necessary to properly position the harness. • CAREFULLY lift/ peel the material up then, once the harness is tucked fully into the groove using a plastic trim tool, push the material back down into place. • Tuck the LED harness past the sealing material into its corresponding retaining groove. Continued… Bulletin Number: 07-81-14; Date: 02/03/14 Page 4 • Reinstall all the bulb sockets, reconnect the vehicle harness then refit the combination lamp making sure the slot in the side of the housing engages the retaining clip on the body properly. • Start the vehicle and verify all the combination lamp functions operate properly. • Torque the mounting bolts to 7.5 Nm (5.5 ft-lb) to complete the procedure. WARRANTY / CLAIM INFORMATION For vehicles within the Basic New Car Limited Warranty period, this repair may be claimed using the following information: LABOR DESCRIPTION LABOR OPERATION # FAIL CODE LABOR TIME BOTH REAR COMBINATION LAMPS R&R A916-204 XCB-48 0.3
SEOCONTENT-END
This product presentation was made with AAWP plugin.