Side Window Deflector – 2022 Subaru WRX

SEOCONTENT-START

Newly created お 客O様ctobe用r 2021 Sold by: SUBARU CORPORATION Content Date Revision history Precautions △００ １ INSTALLATION MANUAL SIDE WINDOW DEFLECTOR 1. Be sure to observe the contents in CAUTION for installation described in the main text during the work. Failure to observe them may cause coming-off or peeling-off on the part. It may also prevent the vehicle from functioning. 2. Never use thinner or the like, otherwise the surface of the side window deflector may be corroded. Also, keep the side window deflector away from fire, otherwise it may be deformed. 3. When the ambient temperature is 15°C or lower, warm up all strips of the double-sided tape and around the installation portion of the side window deflector to approximately 40°C using a tool such as a dryer or infrared lamp. Local warm-up may deform the part. Do not use an industrial dryer. 4. After installing the side windoe deflectors, leave them for 2 to 3 hours, and do not drive the vehicle. Avoid washing the vehicle or exposing it to rain or the like for 24 hours. This manual describes how to install and handle the side window deflector. Before installing the part, please be sure to read this manual for proper installation. Side Window Deflector Genuine part number: F0010VC010 Applicable model: WRX 2022MY~ Components No. ① ② ③ ④ ⑤ ⑥ ⑦ Part name RH front side window deflector LH front side window deflector RH rear side window deflector LH rear side window deflector Bracket (a packet of 8 pcs) Cushion (a set of 4 pcs) Instruction Manual Qty. １ １ １ １ ８ ４ １ Repair part No.: RH front side window deflector (F0010FL001): ①×1, ⑤×8, ⑥×4, ⑦×1 LH front side window deflector (F0010FL002): ②×1, ⑤×8, ⑥×4, ⑦×1 RH rear side window deflector (F0010VC013): ③×1, ⑤×8, ⑥×4, ⑦×1 LH rear side window deflector (F0010VC014): ④×1, ⑤×8, ⑥×4, ⑦×1 Bracket set (F0010FL005): ⑤×8, ⑥×4, ⑦×1 ① Ｒ２－１Ａ－２０３６ ② ③ ースカート 取 扱 説 明 書取 付 説 明 書 ④ ⑦ い上Bげrackいet た(a pだackきet oまf mしetaてl fit、tin誠gs) にありがCとushうion ⑤ ⑥ いつもお手元に置いて、正しい取り扱いす。 店または、スバル特約店が指定した販売 Tools to be used 取り扱いをしてください・。Waste cloth →Used in [Fig. 4] and [Fig. 10] さい。 ・Detergent or cleaning agent →Used in [Fig. 4] and [Fig. 10] (Alcohols solvent (isopropyl alcohol, etc.) or Nonane) ・Dryer ２ →Used in [Fig. 8] and [Fig. 14] Completion image Installation procedure (Explains the installation on the LH side.) Front side window deflector (viewed from the inner side) To front CAUTION ・To perform the work safely, park the vehicle on a flat place with sufficient space for the installation work. Then, switch off the engine and apply the parking brake so that the vehicle will not move. Bracket Preparation 1. Installing the brackets (1) Insert the brackets to the bosses on the inner side of the front side window deflector. (2 locations) Bracket [Fig.1] Boss Boss CAUTION ・Install the bracket perpendicular to the double-sided tape application surface. Double-sided tape [Fig. 1] Bracket Rear side window deflector (viewed from the inner side) (2) Insert the brackets to the bosses on the inner side of the rear side window deflector. (2 locations) [Fig.2] To rear Bracket Bracket CAUTION ・Install the bracket perpendicular to the double-sided tape application surface. Double-sided tape Boss Boss Bracket [Fig. 2] ３ Glass run channel 2. Preparation for installation of front side window deflector (1) Open the front door, and fully open the window glass. Then, pull down the glass run channel. [Fig.3] ・When the room lamp is lit, turn it off. Pull down. CAUTION ・When pulling down the glass run channel, be careful not to apply too much force locally, otherwise the glass run channel may break. [Fig.3] Surface to be degreased and cleaned <Cushion attachment position> Glass run channel Door sash Cushion Reference for attachment: Top of corner (2) Remove stain or wax on the front side window deflector installation portion (hatched area in Fig. 4) with detergent (or cleaning agent), and let it completely dry. [Fig.4] (3) Attach a cushion to the pillar cover step portion of the front door sash. When attaching, use the lower side as the reference, and align the cushion to the top of the sash corner Cushion Pillar cover Caution 0mm Cushion radius Glass run channel Pillar cover radius while paying attention not to make a contact with the glass run channel. [Fig.4] ・Attach the cushion so that no gap will be made Door sash [Fig.4] CAUTION on the pillar cover and also the upper side of the cushion will not protrude from the side window deflector. Backing paper C Backing paper B To front (4) Completely remove the backing paper A at the end of the double-sided tape on the inner side of the front side window deflector. For each of the backing paper B, C, and D, remove approximately 3 to 10 cm from the end, and bend it outward. Backing paper D Front side window deflector (viewed from the inner side) Backing paper A Completely remove. CAUTION ・Be sure to remove the backing paper as shown in Fig. 5, otherwise they cannot be removed during installation. [Fig.5] [Fig.5] <Sectional view of bracket installation area> Door sash Side window deflector Installation 3. Installation of the front side window deflector (1) Insert the tips of the brackets installed to the side window deflector in Section 1 (1) into the front door sash. [Fig.6][Fig.7] Insert. Bracket [Fig.6] ４ Insert into the door sash. 取 付 作 業 者 用 Bracket <Sectional view of upper Bracket Front side window deflector <Sectional view of step [Fig.7] 本書は、フロントバンパースカー取り付け前には、本書を必ずお読取り付け後は、本書を必ずお客様 注 意 事 項 １．本文中の取り付け上の 注意注意を無視して取り付けるる恐れがあります。 ２．フロントバンパースカート (2) When installing the front siでde、wi使nd用owしdなefleいctでorくin ださい Section 3 (1), fit the rear enてd oくf tだheさsidいe 。window end installation position> portion installation position> deflector along the st３ep．of雰th囲e fr気on温t d度ooがr s１ash５a℃nd以下の Door 2㎜ (No protrusion from the outer edge Fitting along step Side window deflector pillar cover, and make adjuとstmフeロnt ンso トthaバt tンheパsidーe スカー window deflector will not protrude from the outer sash of sash) Side window edge of the sash and pillarめcoるverと. 製品が変形する事が deflector Door sash Pillar cover The installation tolera４nc.e m本u製st b品e 取wit付hinけ±後0.5、m２m～. ３時 Backing paper ② ① Backing paper ③ CAUTION 以内の洗車や、雨水[Fi等g.8の] 付 ・Install the side window deflector so that it will not protrude from the outer edge of the sash and pillar cover. Otherwise, it may cause 販 interference with the vehicle or injury. ・Avoid making any gap at the step of the sash and pillar cover, when installing. Otherwise, rain or water may intrude inside. Restore. Glass run channel (3) While holding the side window deflector at the installation position, slowly remove each of the baking Front side window deflector <Sectional view of rear end installation position> *The dimension is for reference only. (Dimension from paper in the order of ①, ②, and ③ shown in the figure. At that time, be careful not to allow the backing paper of the double-sided tape to break at midpoint. [Fig.8] Side window deflector ａ the outer edge of pillar cover) 3.5 ㎜ Pillar cover (4) Apply a firm pressure with a force of 49 N or more (at least to the extent that the vehicle body is moved) evenly onto the entire double-sided tape application surface on the front door sash and pillar cover. [Fig.8] <b-b sectional view of installation position>ｂ ｂ (Dimension from the outer edge of sash) *The dimension is for reference only. 2㎜ CAUTION ・To apply the double-sided tape onto the pillar cover at the rear end of the front door, firmly press the area around the corner of the side window deflector. Press firmly. Side window Front sideａ window deflector Door sash Front side window deflector Make sure that the double- sided tape adheres well. deflector Pillar cover Cap <a-a sectional view of installation position> Side window deflector [Fig.8] Double-sided tape (5) Restore the glass channel. The installation work has been completed. [Fig.8] (6) Install the RH side window deflector in the same way. Check (1) Visually check the side window deflector from the above and below to make sure that the double-sided tape adhesive surfaces adhere well. (2) If the side window deflector surface is dirty after the installation work, wipe it off to clean up with a waste cloth or the like. ５ Glass run channel Preparation (Explains the installation on the LH side.) びに取り扱い方法について記載してあります。けを行ってください。 4. Preparation for installation of rear side window deflector (1) Open the rear door, and fully open the window glass. Then, pull down the glass run channel. Pull down. [Fig.9] ・When the room lamp is lit, turn it off. 反映させて作業を行ってください。もしの原因になるほか、車両の機能を阻害す 用しますと表面を侵す恐れがありますのると変形する恐れがありますので注意し 〔[F図ig９.9]〕 CAUTION ・When pulling down the glass run channel, be careful not to apply too much force locally, otherwise the glass run channel may break. Surface to be degreased and cleaned 、赤外線ランプ等で両面テ－プ部分全体 ４０℃程に暖めてください。局部的に暖ドライヤ－の使用は避けてください。 (2) Remove stain or wax on the rear side window deflector installation portion (hatched area in Fig. 10) with detergent (or cleaning agent), and let it completely dry. [Fig.10] 走行しないCuでshion ださい。また、２４時間 <Cushion attachment position> (3) Attach a cushion to the pillar cover step portion of 。 式会社 Pillar cover Reference for attachment: Top of corner radius Glass run channel 0㎜ Cushion Pillar cover Cushion Caution Glass run channel Door sash １ the rear door sash. When attaching, use the lower side as the reference, and align the cushion to the top of the sash corner radius while paying attention not to make a contact with the glass run channel. [Fig.10] ・Attach the cushion so that no gap will be made Door sash 〔[F図ig.1100〕] CAUTION on the pillar cover and also the upper side of the cushion will not protrude from the side window deflector. Backing paper Backing paper (4) Remove each of the backing paper of the double-sided tape on the inner side of the rear side window deflector approximately 3 to 10 cm from the end, and bend it outward. [Fig.11] ・Be sure to remove the backing paper as Rear side window deflector (viewed from the inner side) Backing paper To front CAUTION shown in Fig. 11, otherwise they cannot be removed during installation. [Fig.11] <Sectional view of bracket installation area> Door sash Side window deflector Installation 5. Installation of the rear side window deflector (1) Position the rear side window deflector so that its front and rear end positions will be well balanced, and then insert the tips of the brackets installed to the side window deflector in Section 1 (2) into the rear door sash. [Fig.12][Fig.13] Insert. Bracket [Fig.12] ６ (2) When installing the rear side window deflector in Section 5 (1), fit the front end of the side window deflector to the step of the rear door sash and pillar cover, and make adjustment so that the side window deflector will not protrude from the outer edge of the sash and pillar cover. The installation tolerance must be within ±0.5 mm. [Fig.14] Rear side window deflector Bracket [Fig.13] Backing paper ③ ① ② <Sectional view of upper end installation position 2㎜ otr Side window deflector Door sash from the o edge of sash) <Sectional view of step portion installation position> Side window deflector Fitting along step Pillar cover Door sash Restore. Glass run channel Rear side window deflector 3.5 ㎜ <Sectional view of front end installation position> Side window deflector Pillar cover (Dimension from the outer edge of pillar cover) reference only. [Fig.14] Check (1) Visually check the side window deflector from the above and below to make sure that the double-sided tape adhesive surfaces adhere well. (2) If the side window deflector surface is dirty after the installation work, wipe it off to clean up with a waste cloth or the like. Pillar cover Double-sided tape ・To apply the double-sided tape onto the pillar cover at the front end of the rear door, firmly press the area around the corner of the side window deflector. Press firmly. Make sure that the double- sided tape adheres well. ７ Insert into the door sash. (3) While holding the side window deflector at the installation position, slowly remove each of the baking paper in the order of ①, ②, and ③ shown in the figure. At that time, be careful not to allow the backing paper of the double-sided tape to break at midpoint. [Fig.14] (4) Apply a firm pressure with a force of 49 N or more (at least to the extent that the vehicle body is moved) evenly onto the entire double-sided tape application surface on the rear door sash and pillar cover. [Fig.14] (6) Install the RH side window deflector in the sam way. (5) Restore the glass channel. The installation work has been completed. [Fig.14] ・Install the side window deflector so that it will not protrude from the outer edge of the sash and pillar cover. Otherwise, it may cause interference with the vehicle or injury. ・Avoid making any gap at the step of the sash and pillar cover, when installing. Otherwise, rain or water may intrude inside. CAUTION CAUTION

**************************************************************************************************************

**************************************************************************************************************

SEOCONTENT-END