NHTSA ID Number: 10228794
Manufacturer Communication Number: 07-215-22
Summary
This bulletin announces availability of a reprogramming file for the Body Integrated Unit (BIU) to address rare cases of battery drain while the mechanical key (key start models) is inserted into the ignition.
NUMBER: 07-215-22
DATE: 12/29/22
INTRODUCTION:
This bulletin announces availability of a reprogramming file for the Body Integrated Unit (BIU) to address rare cases of battery drain while the mechanical key (key start models) is inserted into the ignition. This is caused by the Controller Area Network (CAN) remaining awake whenever the key is in the ignition switch. This enhanced logic allows the BIU to enter into sleep mode. If a battery drain issue is encountered under the condition described, perform the reprogramming procedure outlined below.
PRODUCTION CHANGE INFORMATION:
The production change information is currently TBD.
PAK FILE APPLICABILITY:
This file is included in the July 2022 SSM software update.
SERVICE PROCEDURE / INFORMATION:
REMINDER: Customer satisfaction and retention starts with performing quality repairs.
- Reprogram the BIU following the normal FlashWrite procedure.
Subaru
of America, Inc. (SOA) highly recommends utilizing either the Subaru Midtronics DCA8000 Dynamic Diagnostic Charging System or the Subaru Midtronics GR8-1100 Diagnostic Battery Charger to the vehicle in the Power Supply Mode feature anytime a vehicle control module is being reprogrammed. Once the Midtronics charger is connected to the vehicle, if the battery is fully charged, it will take less than three (3) minutes to boot-up the charger, select the Power Supply Mode, and have the battery voltage stabilized and ready for reprogramming.
NOTES:
- For instructions on using the Power Supply Mode, reference the applicable User Manual for the Midtronics DCA-8000 Dynamic Diagnostic Charging System and the Midtronics GR81100 Diagnostic Battery Charger on STIS.
- Confirm all electrical loads such as lights, audio, HVAC, seat heaters, and rear defroster are all switched OFF before setting up the charger for Power Supply Mode.
- Select the correct battery type (Enhanced Flooded, Flooded, Gel, AGM or AGM Spiral).
- Input the CCA which matches the vehicle’s battery. NOTE: OE and replacement batteries have different CCA ratings. Always confirm the battery’s CCA rating before proceeding.
- If using a DCA-8000 Dynamic Diagnostic Charging System, set the power supply voltage to 13.5 Volts.
- DO NOT connect the DST-i or DST-010 until the Power Supply mode function has completed its battery test mode and the Charging Voltage has dropped to and shows a steady 13.5 Volts on the display.
- Once Power Supply Mode reaches a steady 13.5 Volts, connect the DST-i or DST-010 to the OBD connector and proceed with initiating the normal FlashWrite reprogramming process.
- Amperage will fluctuate based upon the vehicle’s demand for power. NOTE: If the voltage rises beyond 14 Volts while programming is in process, the procedure will abort. This can indicate a need to test or charge the vehicle battery before any further attempt at programming is made.
- ALWAYS set the power supply voltage to 13.5 Volts when using Power Supply Mode. NEVER turn the ignition switch on when charging at voltages 15 Volts or higher.
REMINDER: If the DCA-8000 or GR8-1100 indicates the vehicle’s battery must be charged, charge the battery fully before proceeding to reprogram the vehicle while using the Power Supply Mode.
NOTE: Control module failures resulting from battery discharge during reprogramming are not a matter for warranty. Should any DTCs reset after the reprogramming update is performed, diagnose per the procedure outlined in the applicable Service Manual.
VERY IMPORTANT:
This information is applicable to the Subaru Midtronics DCA-8000 Dynamic Diagnostic Charging System and the Subaru Midtronics GR8-1100 Diagnostic Battery Charger ONLY. It does not apply to any other brand / type of “generic” battery charger whatsoever. ONLY the DCA-8000 and the GR81100 and their Power Supply Mode feature have been tested and approved by SOA.
1 Affected Product
Vehicle
1 Associated Document
Manufacturer Communications
NUMBER: 07-215-22
DATE: 12/29/22
MC-10228794-0001.pdf 1374.405KB
- Catch Battery Problems Early: Featured in two videos by Project Farm, a popular YouTube channel with millions of subscribers, the ANCEL BA101 helps you quickly spot battery issues before they leave you stranded. It provides easy-to-understand readings for State of Health (SOH), State of Charge (SOC), voltage, current, CCA, plus cranking and charging system tests, so you can better understand your battery and help avoid unexpected breakdowns
- Know the Real Condition: Don’t let inaccurate readings lead to costly surprises. Built with high-quality copper crocodile clips and a precision smart chip, this battery tester is designed to deliver dependable results. For the most accurate test, enter the correct battery type, rating value (such as CCA/Ah), and temperature exactly as shown on your battery label, so you get a clearer picture of your battery’s true condition
- Fast, Clear, Hassle-Free Testing: The classic black-and-white screen, adjustable contrast, and white backlight make results easy to read in bright sunlight or low-light conditions. One-handed operation keeps testing simple, while direct power from your vehicle’s battery means no charging and no internal batteries to deal with. Multi-language support makes it easier for more users to test with confidence
- Protection When Mistakes Happen: Built-in 4-in-1 protection helps guard against reverse polarity, short circuits, overcurrent, and overvoltage for safer testing, especially in tight spaces where clamp slips or wiring mistakes can happen. The 3x reinforced ABS housing adds extra durability and helps protect both the tester and your battery during everyday use
- Built for More 12V Batteries: Supporting global standards including JIS, EN, DIN, SAE, BCI, GB, CA, MCA, and IEC, this tester works with 12V batteries used in cars, trucks, boats, RVs, ATVs, lawnmowers, golf carts, and motorbikes over 30Ah. Compatible with Flooded, AGM, GEL, and EFB batteries. Not for lithium batteries, non-12V batteries (6V/8V/24V), or motorcycles below 30Ah. For 6V testing, choose BA101 Plus. For 24V testing, choose BA101 PRO
- [Car Battery Tester] You can easily test and inspect your 12V lead-acid battery with this TOPDON car battery tester. The SOH (State of Health), SOC (State of Charge), Voltage, Current, Rating, and numerous other understandable analytical data are provided by this battery tester. It is compatible with 100-2000CCA regular flooded, AGM flat plate/spiral, EFB, and GEL for their optimum performance.
- [Wide Application] This 12V battery load tester can only be powered on once it is properly attached thanks to a safe passive testing approach. You may test the batteries of a number of vehicles, including cars, motorbikes, trucks, RVs, ATVs, SUVs, boats, yachts, lawnmowers, and even golf carts, without needing to charge the device first.
- [3 Testing Function] A battery health test will determine whether or not the battery is in excellent operating order. A cranking test will determine whether or not the electrical system has sufficient power to start the engine. Check to see that the charging current, rectifier diode, and generator are all functioning normally. This handy auto battery analyzer makes sure your summer road trips won’t end on a flat.
- [Ergonomic Features] To help you rapidly determine the health of the battery, this load battery tester is built with three different colors of LEDs. It's easy to use because it operates through a menu system. Additionally, for a reliable and secure connection during the testing process, premium-quality copper clamps have polarity reverse prevention and spark proof features.
- [Great Choice] The TOPDON BT100 is small and compact, making it simple to keep in a glove box or center console. This battery load tester's rapid and precise results will enable you to decide whether your car battery needs to be replaced or jump-started making it an excellent choice for auto shops, garages, and DIY users who frequently check batteries.
- 【Reliable Automotive Car Battery Tester】 KW208 is the most cost-effective battery load tester compared to other brands, it has all the functions you need and the lowest cost that you can afford. KW208 can test all 12V batteries(100-2000CCA) including regular flooded, AGM flat plate, AGM spiral or gel batteries. Provide overall analysis of batteries’ condition and help you know their status in advance before it dies. KW208 battery analyzer supports cranking and charging system tests also alternator and starter test. Conveniently store this car battery tester for batteries in your glove box or garage, ready for use whenever needed.
- 【Galvanized Alloy Battery Clips】This battery tester has updated it's clips since 2025, thanks for the galvanized alloy battery clips, it's more durable also bring lager contact when connected with battery, it greatly improved the testing accuracy(99.7%) also safer with fully wrapped material. KW208 12V battery load tester gives you reliable and overall battery parameters such as voltage, internal resistance, cold cranking amp and AH capacity, battery health and charge status. Additionally, battery cca tester will also show you professional advice whether to replace or recharge the battery. NEW REPLACEMENT AVAILABLE FOR ANY QUALITY ISSUE.
- 【 >99.7% High Accuracy】Thanks to KW208 meter‘s powerful and smart AI chip, it provides more than 99.7% precise testing results within milliseconds, greatly improving the testing speed and testing accuracy compared to other battery testers. Besides KW208 is the only battery tester that has over 7000+ rating and is the most reliable and popular car battery tester on Amazon.
- 【Plug and Play】 KW208 12 volt battery load tester and analyzer allows you to test batteries both in-vehicle and out-of-vehicle, and even test dead batteries. Just connect the tester’s clips with battery then it will turn on and be ready to test and analyze battery. It’s that easy! Definitely KW208 is your best choice for there is no need to spend more expensive cost to purchase battery testers as their functions are the same.
- 【Starter& Alternator Tester】KW208 not only a great car battery load tester that tests batteries cranking & charging system but also can test alternator's charging and starter's cranking conditions. And it can also switch up to 8 languages for different needs.
- Universal Battery Tester 12V / 24V: TopDiag BT300 battery load tester is able to detect the faults of car starting system and charging system, perform quick test and standard test, can test all automotive starter batteries, such as ordinary lead-acid batteries, AGM flat batteries. AGM spiral batteries and gel batteries. BT300 car battery checker can test most of the current battery standards, include: CCA, JIS, GB, SAE, MCA, CA, DIN, IEC, EN, BCI, etc. Notice: It's not compatible with 6V batteries and is not suitable for use with lithium batteries.
- Accurate Battery & Alternator Diagnosis: Equipped with intelligent chips, TopDiag 12v battery tester BT300 delivers reliable results for battery health (SOH), charge status (SOC), CCA, and impedance. No more guesswork—select the correct battery type/CCA value, and get precise data in 10 seconds (Note: input correct AH value for quick test, or use standard test for no manual input).
- Cranking Test & Charging Test: TopDiag BT300 automotive battery tester allows to check the conditions of starting system and charging test, so you can view the current battery start test results and battery status and make sure that your car is in good running condition at all times. Support software updates via USB (download from PC)—always get the latest features for better compatibility.
- Wide Compatibility for All 12V/24V Vehicles: TopDiag BT300 auto battery tester can be widely use for all 12V/24V vehicle battery system diagnostics, including but not limited to cars, trucks, buses, diesel vehicles, motorcycles, boats, RVs, beach carts and more.
- Multiple Languages & Software Update Mode: TopDiag BT300 battery testers support up to 7 languages: English, Spanish, German, French, Italian, Portuguese, Polish, etc. Topdiag BT300 battery analyzer also supports software update, ensure you always access to the latest features.
- Effortless Operation - Boasting a “plug-and-test” design, there's no need for complex set-up procedures. Just connect it to the battery following simple steps. Without starting the vehicle, you can read the battery status, and after starting, quickly obtain the alternator status. Whether you're a professional mechanic or an ordinary car owner, you can easily use it to quickly determine if the battery needs jump - starting, replacement, or if the alternator output is normal.
- Reliable Safety Features - Equipped with reverse connection protection and over-voltage protection functions. Even if you accidentally connect the positive and negative poles wrongly or encounter excessive voltage, it can effectively safeguard the tester and the vehicle's circuit, greatly reducing the risks caused by operational errors and making users feel more at ease.
- Precise Testing Results - Fitted with a 4-digit digital LCD display, it offers voltage testing accuracy up to 0.01 volts, providing accurate voltage readings. Additionally, it comes with 8 colored LED indicators that intuitively show the status of the battery or the alternator. The dual-indication design makes test results clear and easy to understand, offering a precise basis for judging the conditions of the battery and charging system.
- Wide Compatibility - The testing voltage range spans from 4 to 20V DC, suitable for detecting the voltage of 12V car batteries and various other devices. The 50cm long extension cable, combined with 30A alligator clips, enables convenient and flexible connections, adapting to different testing scenarios.
- Durable and Comfortable Design - The surface of the device is treated with black rubber paint, offering a comfortable hand-feel and a stable grip that's not easy to slip. Its compact design and light weight of only 150 grams make it easy to carry and store. Whether placed in the car for emergencies or in a professional toolbox, it takes up little space and ensures long-term reliability.
SEOCONTENT-START
Bulletin Number: 07-215-22; Date: 12/29/22 Page 1 of 3 SERVICE BULLETIN Continued… CAUTION: VEHICLE SERVICING PERFORMED BY UNTRAINED PERSONS COULD RESULT IN SERIOUS INJURY TO THOSE PERSONS OR TO OTHERS. Subaru Service Bulletins are intended for use by professional technicians ONLY. They are written to inform those technicians of conditions that may occur in some vehicles, or to provide information that could assist in the proper servicing of the vehicle. Properly trained technicians have the equipment, tools, safety instructions, and know-how to do the job correctly and safely. If a condition is described, DO NOT assume that this Service Bulletin applies to your vehicle, or that your vehicle will have that condition. Subaru of America, Inc. is ISO 14001 Compliant ISO 14001 is the international standard for excellence in Environmental Management Systems. Please recycle or dispose of automotive products in a manner that is friendly to our environment and in accordance with all local, state and federal laws and regulations. NUMBER: 07-215-22 DATE: 12/29/22 APPLICABILITY: 2022MY WRX SUBJECT: Battery Drain With Mechanical Key Inserted In Ignition INTRODUCTION: This bulletin announces availability of a reprogramming file for the Body Integrated Unit (BIU) to address rare cases of battery drain while the mechanical key (key start models) is inserted into the ignition. This is caused by the Controller Area Network (CAN) remaining awake whenever the key is in the ignition switch. This enhanced logic allows the BIU to enter into sleep mode. If a battery drain issue is encountered under the condition described, perform the reprogramming procedure outlined below. PRODUCTION CHANGE INFORMATION: The production change information is currently TBD. PAK FILE APPLICABILITY: Model MY Specification File Description Decryption Keyword WRX 22 2.4L Turbo 82201VC011.pak2 3F924F5D This file is included in the July 2022 SSM software update. SERVICE PROCEDURE / INFORMATION: REMINDER: Customer satisfaction and retention starts with performing quality repairs. • Reprogram the BIU following the normal FlashWrite procedure. Subaru of America, Inc. (SOA) highly recommends utilizing either the Subaru Midtronics DCA8000 Dynamic Diagnostic Charging System or the Subaru Midtronics GR8-1100 Diagnostic Battery Charger to the vehicle in the Power Supply Mode feature anytime a vehicle control module is being reprogrammed. Once the Midtronics charger is connected to the vehicle, if the battery is fully charged, it will take less than three (3) minutes to boot-up the charger, select the Power Supply Mode, and have the battery voltage stabilized and ready for reprogramming. ATTENTION: GENERAL MANAGER q PARTS MANAGER q CLAIMS PERSONNEL q SERVICE MANAGER q IMPORTANT – All Service Personnel Should Read and Initial in the boxes provided, right. ©2022 Subaru of America, Inc. All rights reserved. Bulletin Number: 07-215-22; Date: 12/29/22 Page 2 of 3 Continued… NOTES: • For instructions on using the Power Supply Mode, reference the applicable User Manual for the Midtronics DCA-8000 Dynamic Diagnostic Charging System and the Midtronics GR8- 1100 Diagnostic Battery Charger on STIS. • Confirm all electrical loads such as lights, audio, HVAC, seat heaters, and rear defroster are all switched OFF before setting up the charger for Power Supply Mode. • Select the correct battery type (Enhanced Flooded, Flooded, Gel, AGM or AGM Spiral). • Input the CCA which matches the vehicle’s battery. NOTE: OE and replacement batteries have different CCA ratings. Always confirm the battery’s CCA rating before proceeding. • If using a DCA-8000 Dynamic Diagnostic Charging System, set the power supply voltage to 13.5 Volts. • DO NOT connect the DST-i or DST-010 until the Power Supply mode function has completed its battery test mode and the Charging Voltage has dropped to and shows a steady 13.5 Volts on the display. • Once Power Supply Mode reaches a steady 13.5 Volts, connect the DST-i or DST-010 to the OBD connector and proceed with initiating the normal FlashWrite reprogramming process. • Amperage will fluctuate based upon the vehicle’s demand for power. NOTE: If the voltage rises beyond 14 Volts while programming is in process, the procedure will abort. This can indicate a need to test or charge the vehicle battery before any further attempt at programming is made. • ALWAYS set the power supply voltage to 13.5 Volts when using Power Supply Mode. NEVER turn the ignition switch on when charging at voltages 15 Volts or higher. REMINDER: If the DCA-8000 or GR8-1100 indicates the vehicle’s battery must be charged, charge the battery fully before proceeding to reprogram the vehicle while using the Power Supply Mode. NOTE: Control module failures resulting from battery discharge during reprogramming are not a matter for warranty. Should any DTCs reset after the reprogramming update is performed, diagnose per the procedure outlined in the applicable Service Manual. VERY IMPORTANT: This information is applicable to the Subaru Midtronics DCA-8000 Dynamic Diagnostic Charging System and the Subaru Midtronics GR8-1100 Diagnostic Battery Charger ONLY. It does not apply to any other brand / type of “generic” battery charger whatsoever. ONLY the DCA-8000 and the GR8- 1100 and their Power Supply Mode feature have been tested and approved by SOA. Bulletin Number: 07-215-22; Date: 12/29/22 Page 3 of 3 WARRANTY / CLAIM INFORMATION: For vehicles within the Basic New Car Limited Warranty period, this repair may be submitted using the following claim information: Labor Description Labor Operation # Fail Code Labor Time BIU Reprogramming A880-308 FCO-48 0.4 NOTE: The PAK file listings provided in this bulletin are the latest available at the time of publishing. Updates are often released thereafter without revision to the original bulletin. For this reason, it is critical to always have the latest version of Select Monitor software installed on your system. IMPORTANT REMINDERS: • SOA strongly discourages the printing and/or local storage of service information as previously released information and electronic publications may be updated at any time. • Always check for any open recalls or campaigns anytime a vehicle is in for servicing. • Always refer to STIS for the latest service information before performing any repairs.
SEOCONTENT-END
This product presentation was made with AAWP plugin.