NHTSA ID Number: 10234854
Manufacturer Communication Number: 1516013R
Summary
Poor Fit of Seat Back Protector
NUMBER: 15-160-13R
DATE: 03/18/13
REVISED: 05/08/13
| APPLICABILITY: | 2013 MY Outback with seat back protector |
| SUBJECT: | Poor Fit of Seat Back Protector |
INTRODUCTION
The 2013 MY Outback has a rear seat back protector available as an accessory. This seat back protector is used along with a cargo tray to protect the back of the rear seats when cargo is loaded into the cargo area when the rear seats are folded down.
When the rear seats are folded up, there is a natural tendency for the seat back protectors to slightly pull away for the rear seat back. This is a natural condition and does not indicate a problem with the installation of the rear seat back protector.
If the seat back protector buckles outward from the rear seat back excessively, please make sure the seat back protector is installed properly. A seat back protector that is installed too low on the rear seat back will interfere with a bracket in between the cargo area floor and the rear seats. This interference causes the seat back protector to buckle when the seats are folded upright.
Check the distance from the top edge of the seat back protector to the point of transition between the rear seat back material and the seat fabric. If the top edge of the seat back protector is not at the right distance from the transition between seat back and seat materials, remove the clips from the seat back protector and reinstall.
Place tray in position and use awl to make holes in the seat back material in all 5 grommet locations.
1 Affected Product
Vehicle
| MAKE | MODEL | YEAR |
SUBARU | OUTBACK | 2013 |
1 Associated Document
Manufacturer Communications
NUMBER: 15-160-13R
DATE: 03/18/13
REVISED: 05/08/13
MC-10234854-9999.pdf 1567.37KB
NHTSA ID Number: 10233449
Manufacturer Communication Number: 1516013
Summary
Poor Fit of Seat Back Protector
1 Associated Document
Manufacturer Communications
NUMBER: 15-160-13
DATE: 03/18/13
MC-10233449-9999.pdf 1556.046KB
- Compatible Models：Front car seat covers fit Subaru（ Outback Forester Crosstrek Legacy Impreza）
- 2026 New Edition: Featuring thicker foam padding and heavier faux leather seat covers, delivering a smoother surface and enhanced support for the same premium look as pictured
- Easy Installation:Innovative quick-install design allows most users to complete cover installation in approximately 3 minutes. Ensures no shifting during driving or getting in/out of the vehicle
- Durable & Protective Leatherette:Effortlessly handles seat scratches, daily wear and tear, pet claw marks, and liquid spills. Simply wipe away everyday stains to keep it looking as good as new
- Classic Style Design:Ideal for protecting new car seats or restoring old ones. Effectively prevents wear and fading of original upholstery while giving your older vehicle a fresh new look
- Thick & Durable Protection – Keep Your Car Seats Looking New: Siivton car seat protector is made of extra-thick, high-density padding that provides excellent cushioning and prevents indentations, scratches, and wear caused by child car seats, booster seats, or heavy gear
- Secure & Stable – Triple Anti-Slip Design: Designed with a non-slip mesh backing, anti-slip tab that tucks into seat creases, and an adjustable headrest strap, this seat protector stays firmly in place — even during bumpy rides or frequent in-and-outs
- ISOFIX Compatible – Smart Design for All Car Seats: Features convenient cutouts on both sides to ensure seamless installation of ISOFIX or LATCH-equipped child safety seats without interfering with seat anchors or safety features
- Kid-Friendly Storage – 2 Mesh Pockets for Easy Access: Built-in mesh pockets at the bottom offer handy storage for toys, snacks, bottles, or wipes — keeping your back seat organized and your child entertained on long drives
- Fits Most Vehicles – For Leather & Fabric Seats: Universal fit for most car, SUV, or truck seats. Compatible with both leather and fabric interiors, offering full back seat coverage while maintaining your car’s clean, premium look
- PROTECT YOUR CAR UPHOLSTERY: MORROLS stylish yet highly resilient car seat protector 2 pack protect your car’s upholstery, extend your car's usage life and make it look like brand new! keeps comfort while driving your car. No matter backseat or driver seat, convenient for family trip.
- SAFEFIT DESIGN: Car seat protector kids has adjustable safety straps that buckled the top around the headrest, tucked the flap into the seat, Anti slip dots for extra grip, Don't worry about the seat protectors sliding from the car seat, PVC leather corner Ensuring your child car seat stays in place.
- MAXIMUM COVERING: XL car seat protector fit to most vehicles - say goodbye to stains and spills! Suitable for infant car seat protector, driver car seat protector, car seat protector booster, sedan, SUV, Truck... Two generously sized mesh pockets provide more storage for your child's toys, food and those handy essentials.
- EASY TO CLEAN: Black car seat protector made with enhanced waterproof 600D polyester fabric material, easy to install and remove .no need to spend much time on cleaning works, You just prepare a damp cloth, stains can be wiped off easily.
- MULTI FUNCTION PROTECTOR: Car seat protector for child car seat also for dogs car mats,cat seat cover. It's Parent's Favorite. leather car seat protector also can minimize pet scratches or drooling, Say goodbye to dirty, damaged seats once and for all!
- 【Design for Subaru 】:The dog car seat cover compatible with Subaru, Which is specially designed for Subaru Crosstrek Outback Forester rear seat and so on.
- 【Premium Material】:Made of premium material Oxford cloth, which is long lasting-use, waterproof, dirt-resistant, easy to clean, keeping your car interior safe from scratches, fur, and urine.
- 【Non-Slip Backing】: Come with 2 sets of adjustable straps and 2 seat anchors from sliding around, Two velcro openings allow you to fasten your seatbelt without interruption, the bottom of the product is also made of non-slip material.
- 【Easy Storage & Clean 】:When you don't need to use it, you can fold it and store it anywhere in the car to save space; What's more, it's easy to clean with a damp cloth, vacuum or Water Shower.
- 【Easy to install】: Easy to install, use the adjustable shoulder straps and clip around your backseat headrests, then tuck the 2 seat anchors into the back seat gaps, installation is complete.
- ✓ All-Time Protection - Our Back Seat Protector will ensure that your seat remains in perfect condition by protecting leather or upholstery from muddy little feet that bring along with them dirt and mud! Gone will be the days of traveling with a less than perfect car interior.
SEOCONTENT-START
Bulletin Number: 15-160-13R; Date: 05/08/13 Page 1
INTRODUCTION
The 2013 MY Outback has a rear seat back protector available as an accessory. This seat back
protector is used along with a cargo tray to protect the back of the rear seats when cargo is loaded into
the cargo area when the rear seats are folded down.
When the rear seats are folded up, there is a natural tendency for the seat back protectors to slightly
pull away for the rear seat back. This is a natural condition and does not indicate a problem with the
installation of the rear seat back protector.
If the seat back protector buckles outward from the rear seat back excessively, please make sure the
seat back protector is installed properly. A seat back protector that is installed too low on the rear seat
back will interfere with a bracket in between the cargo area floor and the rear seats. This interference
causes the seat back protector to buckle when the seats are folded upright.
NUMBER: 15-160-13R
DATE: 03/18/13
REVISED: 05/08/13
APPLICABILITY: 2013 MY Outback with seat back protector
SUBJECT: Poor Fit of Seat Back Protector
SERVICE BULLETIN
ATTENTION:
GENERAL MANAGER q
PARTS MANAGER q
CLAIMS PERSONNEL q
SERVICE MANAGER q
IMPORTANT – All
Service Personnel
Should Read and
Initial in the boxes
provided, right.
CAUTION: VEHICLE SERVICING PERFORMED BY UNTRAINED PERSONS COULD
RESULT IN SERIOUS INJURY TO THOSE PERSONS OR TO OTHERS.
Subaru Service Bulletins are intended for use by professional technicians ONLY. They
are written to inform those technicians of conditions that may occur in some vehicles, or
to provide information that could assist in the proper servicing of the vehicle. Properly
trained technicians have the equipment, tools, safety instructions, and know-how
to do the job correctly and safely. If a condition is described, DO NOT assume that this
Service Bulletin applies to your vehicle, or that your vehicle will have that condition.
SUBARU OF AMERICA, INC. IS
“ISO 14001 COMPLIANT”
The international standard for excellence
in Environmental Management Systems.
Please recycle or dispose of automotive
products in a manner that is friendly to our
environment and in accordance with all
local, state and federal laws and regulations.
Typical seat back protector fit Poor appearance of seat back protector due
to improper installation
Continued…
Bulletin Number: 15-160-13R; Date: 05/08/13 Page 2
Continued…
Check the distance from the top edge of the seat back protector to the point of transition between
the rear seat back material and the seat fabric. If the top edge of the seat back protector is not at the
right distance from the transition between seat back and seat materials, remove the clips from the seat
back protector and reinstall.
For proper placement of the rear seat back protector, make sure the
recommended placement in the installation instruction is followed.
Place tray in position and use awl to make holes in the seat back material in all 5 grommet locations.
x5
A
Transition between carpet
and seat material
Maintain equal distances
between edge of seats
and tray
Rear seats folded
down
Seat
material
Transition between
seat back material
and seat material
Rear seat
back
material
Rear seat back
protector
2 1/2″ – 2 3/4″
2-1/2″ – 2-3/4″
Bulletin Number: 15-160-13R; Date: 05/08/13 Page 3
Seat back protector installed too low. Dimension
from transition between seat back material and
seat material to top edge of seat back protector
must be between 2 1/2″ and 2 3/4″
Transition between seat back material
and seat material.
Remove clips from seat back
Reinstall seat back protector so that the
top edge is the correct height from the
transition point
Transition between seat back material
and seat material
Continued…
Bulletin Number: 15-160-13R; Date: 05/08/13 Page 4
WARRANTY / CLAIM INFORMATION
For vehicles within the Basic New Car Limited Warranty period, this repair may be claimed using the
following information:
LABOR DESCRIPTION LABOR
OPERATION #
FAIL
CODE
LABOR
TIME
Rear Seat Back Protector R&R, ONE or BOTH A063-803 ZOQ-03 0.2
SEOCONTENT-END
This product presentation was made with AAWP plugin.