Accessory Installation Guide
| 2024MY Ascent Wireless Charger | H671SXC203 |
GENUINE PARTS
INSTALLATION INSTRUCTIONS
PART NUMBER: H671SXC203
DESCRIPTION: 2024 Ascent Wireless Charger
1
Engage Parking Brake.
Turn vehicle OFF.
2
Disconnect the negative battery terminal using a 10mm socket/ratchet.
NOTE: If equipped, disconnect eyelet cable only.
3
Use panel removal tool to remove rubber mat and plastic tray and discard.
4
Use panel removal tool to remove console cover. (Removing shift knob is optional.)
5
Disconnect console power connection.
6
Locate the pre-wired connector just below the USB outlets.
7
Using a wire hook or equivalent (not sharp), release the breakaway tape from the connector. Be careful not to damage any wires.
8
Gently pull the pre-wired connector up and out via the blank terminating connector loop.
9
Disconnect and discard the blank terminating connector.
10
Route the included harness down through the large opening and up around to the pre-wired connector.
11
Plug included harness into pre-wired connector.
12
Wrap connector in foam tape.
13
Tie up excess harness, trim the tie wrap, then tuck down in open cavity.
14
Tuck excess harness back in the cubby hole.
15
Leave about 4 inches of harness out.
16
Reconnect console power connector.
17
Reinstall console cover.
(NOTE: Wireless Charger will not seat without this cover back in place.)
18
Connect wireless charger.
19
Align tabs and push down on Wireless Charger to seat.
20
Align tabs and push down on Wireless Charger to seat.
21
After all the connections are complete, re-connect the vehicle’s negative battery cable. Using a 10mm socket/torque wrench, tighten the 10mm nut to 7.5 Nm +/- 2 Nm (0.76 Kgf-m +/- 0.2 Kgf-m, 5.5 ft-lbs +/- 1.5 ft-lbs).
22
Function Check
Place car in ACC or ON mode.
Ensure wireless charger indicator light illuminates in white.
H671SXC203
- 【3-in-1 & Flexible Viewing Angle】You have multiple installation of the car phone holder,it can be installed on the windshield, dashboard,air vent and table securely, and is ideal for cars, trucks, SUVs, etc. This phone holders for your car with a 360-degree rotating and pivoting ball joint that can help you get the most comfortable and safest viewing without neck or eye strain while charging your phone. [ NOTE: Not compatible with Foldable Phone for charging ]
- 【Latest Chip for More Efficient Charging】The MOKPR Wireless Car Charger is a built-in advanced sensor, just place your phone in after power on, it will intelligent identify your phone and Auto-adjusting phone to the best charging area and fast charge.
- 【Automatic Precise Alignment】The car phone mount's arms and foot will auto-opening after connecting to power, and will auto clamping firmly once place your phone inside, then it will intelligent identify and auto-adjusting the phone to the best charging area according to your phone model, don't need to manually adjust the foot to clamping the phone.
- 【Case Friendly & FOD FUNCTION】This wireless charger supports charging through phone cases up to 4mm thick.FOD foreign body detection prevents abnormal charging of equipment, please remove metal/magnetic objects, credit cards or pop holders before charging.
- 【Strong Suction Cup & Secure Stable Install】This phone holder features an extra-strong suction cup, it easily sticks securely on the dashboard or most flat surfaces. Even if driving on a bumpy road, you don’t need to worry about it falling off.
- ✅【Upgraded Intelligent Auto-Clamping】The wireless car charger's arms will auto-opening after connecting to power, and will auto clamping firmly once place your phone in, don't need to manually adjust to clamping the phone. Releasing the phone is as easy as touching a button
- ✅【Auto-Precise Alignment Charging】This wireless car charger mount is built-in advanced sensor, just place your phone in after power on, it will adjust your phone in the best charging area while intelligently identify your device and selects optimal charging power performances, greatly improved charging efficiency
- ✅【3 In 1 Car Phone Holder】This car phone holder and charger is equipped with ultra-durable adhesive base design and air vent clip, which can be freely installed on the dashboard and car air vent to meet your different usage needs. The phone holder is suitable for most cars, pickup trucks, suvs, and taxis. Charge your phone anytime, anywhere in the car, The perfect driving partner for Uber, Lyft, and Instacart drivers
- ✅【FOD Function & Case Friendly】The wireless charging technology and large coil maximize the charging output and efficiency making charging faster than standard car wireless charger. Our car mount wireless charger supports charging through phone cases up to 3mm thick. FOD foreign body detection prevents abnormal charging of equipment, please remove metal/magnetic objects, credit cards or pop holders before charging
- ✅【Secure Stable】The car phone holder mount wireless charging features a strong vent clip and innovative hollow silicone rubber, which can hold your phone without fall off even when driving on bumpy road and will not clamp your phone buttons cause your phone to power off
- 【Auto-Precise Alignment Charging】This wireless car charger mount is built-in advanced sensor, just place your phone in after power on, it will adjust your phone in the best charging area while intelligently identify your device and selects optimal charging power performances, greatly improved charging efficiency. Great gift for Christmas!
- 【Upgraded Intelligent Auto-Clamping】The wireless car charger's arms and foot will auto-opening after connecting to power, and will auto clamping firmly once place your phone in, don't need to manually adjust the foot to clamping the phone.
- 【Make Drive Easier】Combines the wireless charger & car phone mount, offers fast charging and saves you from messing with cables while driving. A 360°rotating sphere can help you get the most comfortable and safest GPS Navigation and viewing angle without neck or eye strains while charging your phone.
- 【Secure Stable】The car phone holder mount wireless charging features a strong vent clip and innovative hollow silicone rubber, which can hold your phone without fall off even when driving on bumpy road and will not clamp your phone buttons cause your phone to power off.
- 【FOD Function & Case Friendly】The wireless charging technology and large coil maximize the charging output and efficiency making charging faster than standard car wireless charger. MOKPR car mount wireless charger supports charging through phone cases up to 4mm thick. FOD foreign body detection prevents abnormal charging of equipment, please remove metal/magnetic objects, credit cards or pop holders before charging.
- 2-in-1 Mounting for 99% Vehicles: This phone holder for car offers both dashboard and vent mounting options, giving first-time wireless car charger buyers more ways to find the right fit for their vehicle. The military-grade 3M dashboard base uses a dual-support structure and is tested through 4 environmental reliability tests from -40°F to 194°F, while the reinforced vent hook is extended by 60% to fit more air vents. Its compact charging head helps reduce windshield obstruction and avoids blocking airflow, making installation easier and lowering the risk of choosing the wrong mount.
- 15W Wireless Charging for Nonstop Driving: This LISEN MagSafe car mount charger combines a magnetic phone holder and 15W wireless car charger in one compact design, helping keep your phone powered throughout the trip. Just place your phone on the mount when you get in, and charging starts automatically; when you arrive, simply lift it off and go. Built for GPS, calls and music on long drives, it is especially useful for Uber, Lyft and delivery drivers who need steady power on the road.
- Strong Magnetic Hold, No Button Blocking: Built with 24 N52 magnets and up to 3800gf magnetic force, this car phone holder is tested to hold the weight of 8 phones at once for a more stable hold on bumpy roads and sharp turns. Its clamp-free magnetic design keeps side buttons accessible, so you can place your phone with one hand and use GPS, calls or music without extra adjustment.
- Ice Blue LED Glow for Interior Style: This magnetic car accessories mount charger features an ice blue LED light ring that adds a modern accent to your car interior at night. The soft glow helps you quickly locate the mount in low-light driving conditions, while the magnetic one-hand snap-on design makes phone placement easier during night drives, parking, commuting and GPS use.
- Wide Compatibility for Shared Family Cars: This MagSafe car mount charger works with iPhone18, iPhone 18 Pro, iPhone 18 Pro Max and iPhone 17/16/15/14/13/12 series, and also supports Samsung Galaxy S26/S25/S24 and Pixel 10/9 series when paired with a MagSafe-compatible case. Its magnetic alignment helps different phone brands stay securely attached and ready for wireless charging, so families who share one car do not need to switch mounts whenever a different person drives.
- 【Fast Wireless Car Charger】Buit-in upgraded chip, MOKPR wireless car charger mount intelligently identify and charges your device in safe. 15W Wireless Fast Charging for LG V50/V40/V30/G8/G7; 10W for Samsung Galaxy S23 Ultra/S23+/S23/S22 Ultra/S22/S21/S20+/S20/Note 10; 7.5W for iPhone 16 Pro Max Plus 15/14/14 plus/14 pro/14 pro max/13/13 Pro/12 Pro Max/12 Pro/12/11/X/XR/8; Note: 15W/10W/7.5W Fast Charging requires QC 3.0 car charger (Not Included), 5W standard wireless charging requires 5V/2A adapter.
- 【Stable & Flexible Viewing Angle】This carbon fiber car wireless charger with a 360-degree rotating and pivoting ball joint can help you get the most comfortable and safest viewing without neck or eye strain while charging your phone.(Please NOTICE that some Air Vent outlet not compatible)
- 【Arms and Foot Auto Clamping Together】The car phone holder mount wireless charging's arms and foot will auto-opening after connecting to power, and will auto clamping firmly once place your phone inside, don't need to manually adjust the foot to clamp the phone.
- 【Automatic Precise Alignment】This car phone mount is a built-in advanced sensor, just place your phone in after power on, it will intelligent identify and auto-adjusting the phone to the best charging area according to your phone model, no need to manually adjust the foot.
- 【Case Friendly & FOD FUNCTION】This car mount wireless charger supports charging through phone cases up to 4mm thick.FOD foreign body detection prevents abnormal charging of equipment, please remove metal/magnetic objects, credit cards or pop holders before charging.
SEOCONTENT-START
GENUINE PARTS
INSTALLATION INSTRUCTIONS
PART NUMBER: H671SXC203
DESCRIPTION: 2024 Ascent Wireless Charger
DESCRIPTION
2024 Ascent Wireless Charger
ISSUE
0.1
DATE
08/21/2023
SUBARU OF AMERICA PAGE
1 / 7
KIT CONTENTS:
Wireless Charging Assembly T-Harness Tie Wrap (Quantity=6)
Foam Tape (Quantity=2) Wireless Charging Information Card
TOOLS REQUIRED:
Philips Screwdriver Torque Wrench Panel Removal Tool 10mm socket and ratchet
Nipper
GENUINE PARTS
INSTALLATION INSTRUCTIONS
PART NUMBER: H671SXC203
DESCRIPTION: 2024 Ascent Wireless Charger
DESCRIPTION
2024 Ascent Wireless Charger
ISSUE
0.1
DATE
08/21/2023
SUBARU OF AMERICA PAGE
2 / 7
Engage Parking Brake.
Turn vehicle OFF.
Disconnect the negative battery terminal using a 10mm socket/ratchet.
NOTE: If equipped, disconnect eyelet cable only.
Use panel removal tool to remove rubber mat and plastic tray and discard.
Use panel removal tool to remove console cover. (Removing shift knob is optional.)
1
2
3
4
GENUINE PARTS
INSTALLATION INSTRUCTIONS
PART NUMBER: H671SXC203
DESCRIPTION: 2024 Ascent Wireless Charger
DESCRIPTION
2024 Ascent Wireless Charger
ISSUE
0.1
DATE
08/21/2023
SUBARU OF AMERICA PAGE
3 / 7
Disconnect console power connection.
Locate the pre-wired connector just below the USB outlets.
Using a wire hook or equivalent (not sharp), release the breakaway tape from the connector. Be careful not to damage any wires.
Gently pull the pre-wired connector up and out via the blank terminating connector loop.
5
6
7
8
GENUINE PARTS
INSTALLATION INSTRUCTIONS
PART NUMBER: H671SXC203
DESCRIPTION: 2024 Ascent Wireless Charger
DESCRIPTION
2024 Ascent Wireless Charger
ISSUE
0.1
DATE
08/21/2023
SUBARU OF AMERICA PAGE
4 / 7
Disconnect and discard the blank terminating connector.
Route the included harness down through the large opening and up around to the pre-wired connector.
Plug included harness into pre-wired connector.
Wrap connector in foam tape.
9
10
11
12
GENUINE PARTS
INSTALLATION INSTRUCTIONS
PART NUMBER: H671SXC203
DESCRIPTION: 2024 Ascent Wireless Charger
DESCRIPTION
2024 Ascent Wireless Charger
ISSUE
0.1
DATE
08/21/2023
SUBARU OF AMERICA PAGE
5 / 7
Tie up excess harness, trim the tie wrap, then tuck down in open cavity.
Tuck excess harness back in the cubby hole.
Leave about 4 inches of harness out.
Reconnect console power connector.
14
15
16
13
GENUINE PARTS
INSTALLATION INSTRUCTIONS
PART NUMBER: H671SXC203
DESCRIPTION: 2024 Ascent Wireless Charger
DESCRIPTION
2024 Ascent Wireless Charger
ISSUE
0.1
DATE
08/21/2023
SUBARU OF AMERICA PAGE
6 / 7
Reinstall console cover.
(NOTE: Wireless Charger will not seat without this cover back in place.)
Connect wireless charger.
Align tabs and push down on Wireless Charger to seat.
Place operation manual in glove box.
18
19
20
17
GENUINE PARTS
INSTALLATION INSTRUCTIONS
PART NUMBER: H671SXC203
DESCRIPTION: 2024 Ascent Wireless Charger
DESCRIPTION
2024 Ascent Wireless Charger
ISSUE
0.1
DATE
08/21/2023
SUBARU OF AMERICA PAGE
7 / 7
After all the connections are complete, re-connect the vehicle’s negative battery cable. Using a 10mm socket/torque wrench, tighten the 10mm nut to 7.5 Nm +/- 2 Nm (0.76 Kgf-m +/- 0.2 Kgf-m, 5.5 ft-lbs +/- 1.5 ft-lbs).
Function Check
Place car in ACC or ON mode.
Ensure wireless charger indicator light illuminates in white.
22
21
**************************************************************************************************************
PIÈCES D’ORIGINE
INSTRUCTIONS D’INSTALLATION
NUMÉRO DE PIÈCE : H671SXC203
DESCRIPTION : Chargeur sans fil pour Ascent 2024
DESCRIPTION
Chargeur sans fil pour Ascent 2024
VERSION
0.1
DATE
2023-08-21
SUBARU OF AMERICA PAGE
1 / 7
CONTENU DE LA TROUSSE :
Ensemble de recharge sans fil Faisceau en T Attache autobloquante (quantité = 6)
Ruban mousse (quantité = 2) Carte d’information sur la recharge sans fil
OUTILS REQUIS :
Tournevis cruciforme Clé dynamométrique Outil de retrait des panneaux Douille de 10 mm avec clé à
cliquet
Pince coupante
PIÈCES D’ORIGINE
INSTRUCTIONS D’INSTALLATION
NUMÉRO DE PIÈCE : H671SXC203
DESCRIPTION : Chargeur sans fil pour Ascent 2024
DESCRIPTION
Chargeur sans fil pour Ascent 2024
VERSION
0.1
DATE
2023-08-21
SUBARU OF AMERICA PAGE
2 / 7
Serrez le frein de stationnement.
Coupez le contact.
Débranchez la borne négative de la batterie à
l’aide d’une douille de 10 mm et d’une clé à
cliquet.
REMARQUE : le cas échéant, débranchez
uniquement le câble à oeillet.
Utilisez l’outil de retrait des panneaux pour
retirer le tapis en caoutchouc et le plateau en
plastique et les mettre au rebut.
Utilisez l’outil de retrait des panneaux pour
retirer le couvercle de la console. (Le retrait du
pommeau de levier de vitesses est facultatif.)
1 2
3 4
PIÈCES D’ORIGINE
INSTRUCTIONS D’INSTALLATION
NUMÉRO DE PIÈCE : H671SXC203
DESCRIPTION : Chargeur sans fil pour Ascent 2024
DESCRIPTION
Chargeur sans fil pour Ascent 2024
VERSION
0.1
DATE
2023-08-21
SUBARU OF AMERICA PAGE
3 / 7
Débranchez la connexion d’alimentation de la console.
Repérez le connecteur précâblé juste en dessous des prises USB.
À l’aide d’un crochet à câble ou d’un outil équivalent (non tranchant), dégagez le ruban Breakaway du connecteur. Veillez à ne pas endommager les câbles.
Tirez doucement le connecteur précâblé vers le haut et vers l’extérieur par la boucle du cache du connecteur.
5
6
7
8
PIÈCES D’ORIGINE
INSTRUCTIONS D’INSTALLATION
NUMÉRO DE PIÈCE : H671SXC203
DESCRIPTION : Chargeur sans fil pour Ascent 2024
DESCRIPTION
Chargeur sans fil pour Ascent 2024
VERSION
0.1
DATE
2023-08-21
SUBARU OF AMERICA PAGE
4 / 7
Débrancher et mettre au rebut le cache du connecteur.
Acheminez le faisceau inclus vers le bas dans la grande ouverture, puis vers le haut jusqu’au connecteur précâblé.
Branchez le faisceau inclus dans le connecteur précâblé.
Enveloppez le connecteur de ruban mousse.
9
10
11
12
PIÈCES D’ORIGINE
INSTRUCTIONS D’INSTALLATION
NUMÉRO DE PIÈCE : H671SXC203
DESCRIPTION : Chargeur sans fil pour Ascent 2024
DESCRIPTION
Chargeur sans fil pour Ascent 2024
VERSION
0.1
DATE
2023-08-21
SUBARU OF AMERICA PAGE
5 / 7
Attachez l’excédant de câble, coupez l’attache
autobloquante, puis enfoncez le tout dans le
compartiment.
Enfoncez l’excédent de câble dans l’autre
compartiment.
Laissez environ 4 pouces de câble sorti.
Rebranchez le connecteur d’alimentation de la
console.
14
15 16
13
PIÈCES D’ORIGINE
INSTRUCTIONS D’INSTALLATION
NUMÉRO DE PIÈCE : H671SXC203
DESCRIPTION : Chargeur sans fil pour Ascent 2024
DESCRIPTION
Chargeur sans fil pour Ascent 2024
VERSION
0.1
DATE
2023-08-21
SUBARU OF AMERICA PAGE
6 / 7
Réinstaller le couvercle de la console.
(REMARQUE : le chargeur sans fil ne peut pas être installé si le couvercle n’est pas en place.)
Branchez le chargeur sans fil.
Alignez les languettes et poussez le chargeur sans fil vers le bas pour l’installer.
Placez le manuel d’utilisation dans la boîte à gants.
18
19
20
17
PIÈCES D’ORIGINE
INSTRUCTIONS D’INSTALLATION
NUMÉRO DE PIÈCE : H671SXC203
DESCRIPTION : Chargeur sans fil pour Ascent 2024
DESCRIPTION
Chargeur sans fil pour Ascent 2024
VERSION
0.1
DATE
2023-08-21
SUBARU OF AMERICA PAGE
7 / 7
Une fois toutes les connexions terminées,
rebranchez le câble négatif de la batterie du
véhicule. À l’aide de la clé à rochet et d’une
douille de 10 mm, serrez l’écrou de 10 mm au
couple de 7,5 +/- 2 Nm (0,76 +/- 0,2 kgf-m,
5,5 +/- 1,5 lb-pi).
Vérification du fonctionnement
Placez le contact en mode ACC (accessoire) ou
ON (démarrage).
Assurez-vous que le témoin du chargeur sans fil
s’allume en blanc.
22
21
**************************************************************************************************************
SEOCONTENT-END
This product presentation was made with AAWP plugin.





