2022 Subaru WRX Center Console Lid – ULTRASUEDE

SEOCONTENT-START

CENTER CONSOLE LID – ULTRASUEDE Installation Manual Component Part No. CENTER CONSOLE LID – ULTRASUEDE 1 No. ① ！ J1310VC623 Applicable Model ： WRX （2022MY～） Genuine Part Number ： Component Part Advice For Installation Operator Precautions Tools to be used Completion drwing Quantity 1. For your safety, stop the vehicle on a flat place, turn off the engine switch and ensure that the parking brake is applied before starting the installation process. 2. Since connector to be detached and attached, make sure to disconnect the power cord of battery (-) negative side before handling electrical components such as the connector. Follow the instructions in the latest service manual for removing and installing the cord of (-) negative side. 3. 4. This document uses the mark to indicate items to be followed and useful tips for the products. This manual describes how to install and handle the INPANE PANEL. Please make sure to read this manual before installation for the correct installation. Please hand this manual to the customer after the installation. ・ Handy remover ・ Phillips screwdriver ・ Box wrench （M10） When installing, be careful not to damage the vehicle and the Center Console Lid parts with tools. Follow the items described using Caution mark in the “Installation procedure” on the following pages for installation. Advice １ △00 Ultrasuede is a registered trademark of Toray Industries, Inc. ①CENTER CONSOLE LID – ULTRASUEDE Manufacturer CORPORATION ２ Installation procedure Installation of Console Lid 1. Remove the Cover ASSY Front. （1）Remove the Tray ASSY Center Lower. （2）Remove the shift knob according to the procedure shown in the figure below. （3）Open the Console Lid, pull up the Cover ASSY Front, and disengage the clips（18 places）. （4）Remove each connector and remove the Cover ASSY Front. Tray ASSY Center Lower consists of Mat and base material. Be careful not to remain the base material on the vehicle. Tip portion of the base material is inserted into the Instrument Panel. Shift knob ④ ③ ② Tray ASSY Center Lower Fitting portion in front – back diction Cover ASSY Front Tray ASSY Center Lower Console Lid ① Release the shift lock using a screwdriver, etc.Shift the select bar to “N range”. ② Push the shift boot downward to remove it. ③ Pull out the pin. ④ Pull out the shift knob upward. Protective tape Caution ： Since connector to be detached and attached, make sure to disconnect the power cord of battery (-) negative side before handling electrical components such as the connector. Reference ： Set the select lever to the “N” position before removing the negative terminal of the battery. For vehicles with a power seat, move the seat to the front most position before removing the negative terminal of the battery. Caution Please pull the Cover ASSY Front upward from the rear end of cup holder and rotate it as shown by the arrow in the illustration to disengage the clip. Since the Instrument Panel is overlapped, pull it out backward after the clips are disengaged. Tip of the Cover ASSY Front is engaged with the Instrument Panel in the front-rear direction, so pulling the tip straight up may damage parts. （Notes in the illustration） Caution Advice 3 SCREW Harness Connector Duct Console R SCREW Console Box R Duct Joint SCREW Cap 2. Remove the Console Box ASSY from the vehicle. 3. Remove the connector of the harness on the vehicle side, which is connected to the Console Box ASSY, and remove the Console Box ASSY. Then, remove the screws （2places）and remove the Duct Console R. （1）Remove the screws（2places）at the front end of the Console Box ASSY. （2）Remove the cap on the side of the Console Box ASSY and remove the bolts. （3）Pull up the tip of the Console Box ASSY and remove the clip engagement（2 places）. （1）Pull the Console Box R backward, and remove the clip engagement（6places）. （2）Remove the harness, which is connected to the SW, and remove the Console Box R. （4）Pull out the Console Box ASSY backward and remove it from the vehicle. The duct attached to the Console Box ASSY is on the vehicle side.（ in the illustration） The duct can be bent slightly, but keep the clip engagement to the minimum when pulling up the tip. Caution Be careful not to pull the Console Box ASSY too much before removing the harness as it may damage the harness. Caution 4. Remove the Console Box R from the Console Box ASSY. 5．Remove the screws（4places）and remove the Console Lid from the Console Box ASSY. 6．①Attach it to the Console Box ASSY in the reverse order of removing the Console Lid. A harness is connected to the SW of the Console Box R. Be careful not to damage the harness when removing. Caution Please keep the removed screw in a safe place as it will be used when assembling. Caution The clips on the Console Box R are engaged in an oblique direction, so pull them diagonally upward to remove them. Advice 4 Console Box R Duct Console R Duct on the vehicle side Duct Joint 7. Attach it to the Console Box ASSY in the reverse order of removing the Console Box R. Be careful not to forget to connect the harness to Switches. Caution 8. Attach it to the Console Box ASSY in the reverse order of removing the Duct Console R. Make sure to insert the Duct Console R into the duct of the Console Box R. Caution 9．Restore the Console Box ASSY in the reverse order of removal. When restoring, be sure to insert the duct of the Console Box ASSY into the duct on the vehicle side. Be careful not to forget to connect the harness. Caution 10. Restore the Cover ASSY Front in the reverse order of removing. 11. Restore the Tray ASSY Center Lower in the reverse order of removing. Pay attention to the positions of the circles and triangles markings on the mat and base material of the Tray ASSY Center Lower. Caution 5 FRONT 12. The work is completed by restoring the Shift Knob work in the reverse order of removing. 13. Make sure that there are no assembly mistakes or scratches on the removed and restored vehicle parts. 14. Connect the removed battery terminal to the battery. 15. After confirming the operation of each electrical component to which the connector has been attached and detached, the work is completed. If the setting is back to a default by removing the battery terminal or the data is lost, please re-enter the data. Caution Guide （2places）｠ Hook（2places）｠

**************************************************************************************************************

SEOCONTENT-END