Accessory Installation Guide
| 2022MY WRX with SPT (Subaru Performance Transmission) – Auto Dimming Mirror | H501SVC000 |
2022MY WRX Interior Auto Dimming Compass Mirror with HomeLink Port Installation Instructions
With EyeSight
Part Number: H501SVC000
Without EyeSight
Part Number: H501SVC100
6MT
Required Tools and Supplies
– Torque screwdriver with (in. lbs.) with Torx T20 Bit and #2 Phillips Bit
– #2 Phillips Head Screwdriver
– ¼” torque wrench
– ¼” drive ratchet with 10mm and 8mm sockets
– ¼” drive 6” extension
– Nylon trim tool
– Clean towels
– Window Glass Cleaner (Optional)
– Dash protection
– Masking tape
Interior Auto Dimming Compass Mirror with HomeLink on models with EyeSight™
Part Number: H501SVC000
Inspect the EyeSight Interior Mirror Kit parts to ensure no missing parts or part defects:
Kit Contents
A) AD Mirror
B) Wire Harness Cover
C) Wire Tie
D) Foam Tape
E) Owner’s User Guide
Open the hood and use the prop rod to hold the hood in the open position. While holding the battery sensor in place with one hand, use a ¼” drive ratchet and 10mm socket to remove the negative battery cable from the negative battery stud. Do not remove negative cable from the battery post. Position / protect the negative cable so it cannot accidentally touch body ground or the negative the battery terminal. Allow (60) seconds before the next installation step to ensure the airbag power supply is discharged.
Carefully remove the negative battery cable from the battery stud only. Do not allow the negative cable accidentally ground during the accessory installation.
While disconnecting the negative battery cable from the stud, hold the battery sensor in place with one hand while loosening the 10mm hex nut that secures the cable to the sensor. This will help support the sensor to prevent damage and also prevent the assembly from rotating on the battery post causing a poor connection.
Preparation
1. Place protection over the RH or LH side sill/door jam when preparing to perform work inside vehicle.
Note: If you are working on the LF side apply the same protection.
2. Place protection center dash and shifter plate trim.
Remove the Factory Mirror
1. Remove the O.E. factory installed Interior Mirror by using a trim stick and carefully dislodge the plastic mirror base cover away from the windshield to expose the tab that retain the O.E. Mirror to the windshield.
2. Carefully pull out on the tab and pull up on the O.E. mirror to remove it from the windshield mirror button.
3. Inspect the mirror button for damages.
4. Properly recycle/ dispose O.E. mirror.
Never remove the OE mirror by pulling directly off the windshield under any circumstances. Not following the Manufacturers OEM mirror removal process will result in windshield damage.
Preparation W/EyeSight
1. Apply masking tape to the overhead console along the retaining bolt access cover.
2. Using a nylon trim tool, carefully remove the retaining screw access cover on the overhead console.
3. Using a #2 Phillips screwdriver, Remove the (2) screws securing the overhead console to the headliner. (Save the screws for reinstallation)
Preparation W/EyeSight
1. Carefully insert your fingers between the headliner and the overhead console. Disengage the rear retaining clips by applying light downward pressure.
2. Lower the overhead console and disconnect the (4) electrical connectors. Set the overhead console aside on a clean protected surface.
Installation W/EyeSight
1. Install the A/D Compass Mirror in place by pushing the mirror down in place over the windshield mirror button.
2. Tighten the T20 Torx screw by using a Torque Screwdriver set to 15.0-inch lbs.
3. Carefully Feed the mirror jumper harness through the right side opening of the EyeSight camera cover.
Installation W/EyeSight
1. Carefully pull down on the headliner trim while feeding the mirror connector overtop.
2. Plug the mirror harness connector into the OE mirror connector in the location shown. (Confirm connection with push-pull method)
3. Pull down slightly on the Eyesight cover and move the mirror harness from the right side opening to the center opening.
4. Ensure the mirror harness is routed inside one of the (2) interior cover “L” hooks to prevent the wire from resting on the EyeSight Camera.
Reassemble W/EyeSight
1. Ensure the wire harness is routed properly in the center headliner trim to avoid any pinch / crush risk during overhead console installation.
2. While holding the overhead console in one hand, reconnect the (4) OE connectors. (Confirm proper connection with push-pull method)
3. Align the (2) rear console clips and carefully push up on the clip locations to re-seat the overhead console to the headliner.
Reassemble W/EyeSight
1. Reinstall the (2) screws previously removed. (Do not overtighten.)
2. Reinstall the bolt cover panel by inserting the (3) tabs facing the rear of the vehicle first, then push up to engage the front of the cover panel to secure it in place.
3. Remove masking tape from overhead console.
➢ Instructions continue on Slide #22
Interior Auto Dimming Compass Mirror with HomeLink on models without EyeSight™
Manuel Transmission Models without EyeSight Only
Inspect the Non-EyeSight AD Compass Mirror with HomeLink to ensure no damage or part defects:
Part Number: H501SVC100
Note: The Non-EyeSight AD Compass Mirror with HomeLink utilizes a high beam assist sensor incorporated into the mirror assembly.
Battery Terminal Stud Removal
Open the hood and use the prop rod to hold the hood in the open position. While holding the battery sensor in place with one hand, use a ¼” drive ratchet and 10mm socket to remove the negative battery cable from the negative battery stud. Do not remove negative cable from the battery post. Position / protect the negative cable so it cannot accidentally touch body ground or the negative battery terminal. Allow (60) seconds before the next installation step to ensure the airbag power supply is discharged.
Carefully remove the negative battery cable from the battery stud only. Do not allow the negative cable accidentally ground during the accessory installation.
While disconnecting the negative battery cable from the stud, hold the battery sensor in place with one hand while loosening the 10mm hex nut that secures the cable to the sensor. This will help support the sensor to prevent damage and also prevent the assembly from rotating on the battery post causing a poor connection.
Preparation
1. Place protection over the RH or LH side sill/door jam when preparing to perform work inside vehicle.
Note: If you are working on the LF side apply the same protection.
2. Place protection center dash and shifter plate trim.
Preparation W/O EyeSight
1. Using a nylon trim tool, carefully remove the wiring upper trim cover from the compass mirror.
2. To separate and remove the lower trim covers, carefully insert a nylon trim tool on an angle where the cover halves meet at the bottom seam. Gently pry apart to disengage the lower retaining claw. Continue to separate the remaining cover claws and remove the covers. Set aside for reinstallation.
Preparation W/O EyeSight
1. Unplug the OE compass mirror.
2. Firmly grab the OE compass mirror and remove by rotating and pulling away simultaneously from the windshield mounting button. (Properly recycle/dispose O.E. mirror)
Installation W/O EyeSight
1. Apply protective masking tape on the High Beam Assist sensor.
2. Install the A/D Compass Mirror with HomeLink by aligning the mirror retention clips with the windshield mirror button and pressing against the mirror to seat the mirror.
3. Rotate the mirror until properly aligned with the reference notch shown.
4. Plug in the AD Compass Mirror with HomeLink. (Confirm connection with push-pull method)
Installation W/O EyeSight
1. Remove protective tape from high beam assist sensor.
2. Reinstall lower mirror trim covers and ensure all claws fully engaged.
3. Reinstall the upper mirror trim cover. Ensure trim cover is fully seated.
Reassemble
1. Remove vehicle protection.
2. Place mirror operation information document in glove box.
Re-connect the negative cable by reinstalling the saved 10mm nut on the stud. Use a ¼” drive torque wrench and a 10mm socket, tighten the cable nut to 66 Inch Lbs. while holding the sensor to prevent damage and prevent the assembly from rotating on the battery post.
Carefully reinstall the negative battery cable to the battery stud only.
While connecting the negative battery cable to the stud, hold the battery sensor in place with one hand while torqueing the 10mm hex nut that secures the cable to the sensor. This will help support the sensor to prevent damage and prevent the assembly from rotating on the battery post causing a poor connection.
Torque mark the battery stud
Function Check
using dark cloth or cardboard, completely cover forward-looking sensor.
Check Your Work
- Ensure the mirror is properly tightened to the windshield (CVT Models). Torque value 15.0-inch lbs. (13.3 – 17.7-inch lbs. ).
- Ensure the battery negative terminal cable is properly reconnected. (Negative battery stud nut torque 5.5ft-lbs (66 in-lbs.).
- Ensure the Bolt / Screw access cover is properly re-installed with no gaps around the panel (CVT Models).
- Ensure the overhead console cover is properly re-installed with no gaps at the headliner with no damage or chipped edges (CVT Models).
- Ensure the wiring cover (CVT Models) and mirror trim covers (6MT Models) are properly installed, seated properly at the mirror base and around the mirror connector.
- Turn the Ignition to the “ON” position and cover the interior mirror light sensor and ensure the interior mirror dims accordingly.
- With your foot on the brake pedal, put the gear selector in “R” mode and ensure the mirror un-dims.
- Ensure map lights turn on and off, door switch functions on and off and telematics illuminates (w/a).
- Ensure no soil marks or smudges are present in the installation area, etc. Clean as required.
- Ensure the mirror glass and windshield glass around the installation area is clean and the factory sticker is left in place on the mirror.
- Auto-Dimming Electrochromic Technology — Automatically darkens when bright headlights hit the rearview mirror, eliminating blinding glare instantly. No more flipping a manual tab. Safer night driving in one upgrade.
- True Universal Fit — Comes with a sliding metal bracket that adapts to most OEM button-style mounts. If your original mount doesn't match, simply swap to the included alternative metal base. Extended cable provides extra length for trucks, vans, and SUVs.
- Premium Frameless Design — Ultra-slim, sleek edge-to-edge glass with no plastic bezel. Looks OEM-pro and gives your interior a modern, clean finish
- DIY Installation (2 Options) — If your vehicle has a pre-wired plug , simply connect the plug-and-play harness and you're done. No plug? No problem — use the included extended cable and wiring kit to hardwire to your ACC fuse or dome light. Everything included: mirror, sliding bracket kit, alternative base, extended cable, wire ties, trim cover, and wrench.
- Why Upgrade from a auto dimming rear view mirror? — A basic rearview mirror costs $20-40 and does nothing. For a few dollars more, your auto-dimming mirror actively works for you every night — reducing eye strain, improving reaction time, and making every drive safer. Fits most vehicles from 2000 to present day.
- These mirrors eliminate the glare of headlights behind you for safer nighttime
- Mirror automatically dims as it detects glare
- The brighter the glare, the more the mirror dims
- Dimensions - 12 x 6.5 x 4.75 in.
- Gentex Auto-Dimming Rear View Mirrors
- AUTO_DIMMING: Automatically darkens to eliminate glare
- FRAMELESS DESIGN: Enhanced aesthetics to complement any vehicle interior
- CAR_TO_HOME AUTOMATION: Control garage doors, gates, home lighting, and more
- INTEGRATED HOMELINK 5: 99% compatibility with garage door openers and security gates
- COMPATIBILITY: Compatible with any wedge mount vehicle along with others using adapters (GENMM1, GENMM2, GENMM3)
- 1.【4.3-inch screen】: Our car rearview mirror display is a 4.3-inch color screen with a resolution of 480*272 and a 16:9 display format; the brightness of 500 cd/m2 ensures clear visibility even in bright sunlight.
- 2.【Auto-dimming function】: The HD is equipped with an automatic dimming function, which can adjust the brightness according to the ambient light conditions and automatically turn on the rearview camera screen when reversing. With an accurate distance scale line display, it can park and reverse correctly, making parking and reversing more convenient and .
- 3.【ABS shell】Our interior rear view mirror made of high-quality and materials. ABS shell, not only ensures its service life, but also adds a stylish and modern feel to your car interior.
- 4.【Practicality】Our 4.3-inch rearview mirror automatic dimming display is designed to provide high-definition and automatic dimming reversing images, solving the problem of poor rearview effect of the car and ensuring a safer parking and reversing experience.
- 5. 【Package List】The package contains 1 car rearview mirror monitor, 1 video cable and power cable, 1 extra cable cover, 1 English manual, 1 bracket and 5 screws, providing everything you need for easy and worry- installation.
- Auto-Dimming
- Integrated Compass
- Homelink integration
- Back Lit Buttons
SEOCONTENT-START
3/16/2022 1 2022MY WRX Interior Auto Dimming Compass Mirror with HomeLink Port Installation Instructions Ensure the VIN matches the workorder and the vehicle date is in the lock period and there are no “Holds” on the vehicle for any reason. Ensure the vehicle calls for the accessory installation. AQA Work instruction 2022MY WRX Interior Mirror A/D with Home Link Release Date: 1/11/2022 Revision: B CAUTION: ACCESSORY INSTALLATIONS PERFORMED BY UNTRAINED PERSONS COULD RESULT IN SERIOUS INJURY TO THOSE PERSONS OR TO OTHERS. Subaru Work Instructions are intended for use by professional accessory installers ONLY. They are written to provide step by step accessory installation instruction for a fast-paced production environment. Properly trained accessory installers have the equipment, tools , safety instructions and know-how to do the job correctly and safely. Included in this information are the use of “special” accessory installation fixtures and templates that are not available to the Retailers or general public. Please refer to the Retailer Installation Instructions found in Subaru Tech Info System (STIS). Without EyeSight Part Number: H501SVC100 With EyeSight Part Number: H501SVC000 6MT CVT 2 – Torque screwdriver with (in. lbs.) with Torx T20 Bit and #2 Phillips Bit – #2 Phillips Head Screwdriver – ¼” torque wrench – ¼” drive ratchet with 10mm and 8mm sockets – ¼” drive 6” extension – Nylon trim tool – Clean towels – Window Glass Cleaner (Optional) – Dash protection – Masking tape Required Tools and Supplies AQA Work instruction 2022MY WRX Interior Mirror A/D with Home Link Release Date: 1/11/2022 Revision: B 3/16/2022 2022MY WRX Interior Auto Dimming Compass Mirror Port Installation Instructions 3/16/2022 AQA Work instruction 2022MY WRX Interior Mirror A/D with Home Link Release Date: 1/11/2022 Revision: B 3 Interior Auto Dimming Compass Mirror with HomeLink on models with EyeSight™ Slides 3-13 2022MY WRX Interior Auto Dimming Compass Mirror Port Installation Instructions Part Number: H501SVC000 4 Inspect the EyeSight Interior Mirror Kit parts to ensure no missing parts or part defects: AQA Work instruction 2022MY WRX Interior Mirror A/D with Home Link Release Date: 1/11/2022 Revision: B 3/16/2022 Kit Contents A) AD Mirror B) Wire Harness Cover C) Wire Tie D) Foam Tape E) Owner’s User Guide 2022MY WRX Interior Auto Dimming Compass Mirror Port Installation Instructions CVT Models with EyeSight Only A Part Number: H501SVC000 E Carefully remove the negative battery cable from the battery stud only. Do not allow the negative cable accidentally ground during the accessory installation. Open the hood and use the prop rod to hold the hood in the open position. While holding the battery sensor in place with one hand, use a ¼” drive ratchet and 10mm socket to remove the negative battery cable from the negative battery stud. Do not remove negative cable from the battery post. Position / protect the negative cable so it cannot accidentally touch body ground or the negative the battery terminal. Allow (60) seconds before the next installation step to ensure the airbag power supply is discharged. While disconnecting the negative battery cable from the stud, hold the battery sensor in place with one hand while loosening the 10mm hex nut that secures the cable to the sensor. This will help support the sensor to prevent damage and also prevent the assembly from rotating on the battery post causing a poor connection. AQA Work instruction 2022MY WRX Interior Mirror A/D with Home Link Release Date: 1/11/2022 Revision: B 3/16/2022 5 2022MY WRX Interior Auto Dimming Compass Mirror Port Installation Instructions 6 1. Place protection over the RH or LH side sill/door jam when preparing to perform work inside vehicle. Note: If you are working on the LF side apply the same protection. 2. Place protection center dash and shifter plate trim. AQA Work instruction 2022MY WRX Interior Mirror A/D with Home Link Release Date: 1/11/2022 Revision: B 3/16/2022 Preparation LH RH 2022MY WRX Interior Auto Dimming Compass Mirror Port Installation Instructions 7 1. Remove the O.E. factory installed Interior Mirror by using a trim stick and carefully dislodge the plastic mirror base cover away from the windshield to expose the tab that retain the O.E. Mirror to the windshield. 2. Carefully pull out on the tab and pull up on the O.E. mirror to remove it from the windshield mirror button. 3. Inspect the mirror button for damages. 4. Properly recycle/ dispose O.E. mirror. Remove the Factory Mirror Never remove the OE mirror by pulling directly off the windshield under any circumstances. Not following the Manufacturers OEM mirror removal process will result in windshield damage. O.E. Mirror Dislodge the O.E. Mirror base cover Using a trim tool pry out on the locking tab Lift up on Mirror to remove Properly recycle/ dispose O.E. mirror. AQA Work instruction 2022MY WRX Interior Mirror A/D with Home Link Release Date: 1/11/2022 Revision: B 3/16/2022 2022MY WRX Interior Auto Dimming Compass Mirror Port Installation Instructions 8 1. Apply masking tape to the overhead console along the retaining bolt access cover. 2. Using a nylon trim tool, carefully remove the retaining screw access cover on the overhead console. 3. Using a #2 Phillips screwdriver, Remove the (2) screws securing the overhead console to the headliner. (Save the screws for reinstallation) AQA Work instruction 2022MY WRX Interior Mirror A/D with Home Link Release Date: 1/11/2022 Revision: B 3/16/2022 Preparation W/EyeSight 2022MY WRX Interior Auto Dimming Compass Mirror with HomeLink Port Installation Instructions 1 2 3 9 1. Carefully insert your fingers between the headliner and the overhead console. Disengage the rear retaining clips by applying light downward pressure. 2. Lower the overhead console and disconnect the (4) electrical connectors. Set the overhead console aside on a clean protected surface. AQA Work instruction 2022MY WRX Interior Mirror A/D with Home Link Release Date: 1/11/2022 Revision: B 3/16/2022 Preparation W/EyeSight Clip Locations 1 2 2022MY WRX Interior Auto Dimming Compass Mirror with HomeLink Port Installation Instructions 10 1. Install the A/D Compass Mirror in place by pushing the mirror down in place over the windshield mirror button. 2. Tighten the T20 Torx screw by using a Torque Screwdriver set to 15.0-inch lbs. 3. Carefully Feed the mirror jumper harness through the right side opening of the EyeSight camera cover. AQA Work instruction 2022MY WRX Interior Mirror A/D with Home Link Release Date: 1/11/2022 Revision: B 3/16/2022 Installation W/EyeSight 1 2 Torque T20 to 15.0-inch lbs. 3 2022MY WRX Interior Auto Dimming Compass Mirror with HomeLink Port Installation Instructions 11 1. Carefully pull down on the headliner trim while feeding the mirror connector overtop. 2. Plug the mirror harness connector into the OE mirror connector in the location shown. (Confirm connection with push-pull method) 3. Pull down slightly on the Eyesight cover and move the mirror harness from the right side opening to the center opening. 4. Ensure the mirror harness is routed inside one of the (2) interior cover “L” hooks to prevent the wire from resting on the EyeSight Camera. AQA Work instruction 2022MY WRX Interior Mirror A/D with Home Link Release Date: 1/11/2022 Revision: B 3/16/2022 Installation W/EyeSight 1 OE connector with Pink breakaway tape. 2 3 2022MY WRX Interior Auto Dimming Compass Mirror with HomeLink Port Installation Instructions 4 “L” Hooks 12 1. Ensure the wire harness is routed properly in the center headliner trim to avoid any pinch / crush risk during overhead console installation. 2. While holding the overhead console in one hand, reconnect the (4) OE connectors. (Confirm proper connection with pushpull method) 3. Align the (2) rear console clips and carefully push up on the clip locations to re-seat the overhead console to the headliner. Reassemble W/EyeSight AQA Work instruction 2022MY WRX Interior Mirror A/D with Home Link Release Date: 1/11/2022 Revision: B 3/16/2022 2022MY WRX Interior Auto Dimming Compass Mirror Port Installation Instructions 2 Clip Locations 3 1 13 1. Reinstall the (2) screws previously removed. (Do not overtighten.) 2. Reinstall the bolt cover panel by inserting the (3) tabs facing the rear of the vehicle first, then push up to engage the front of the cover panel to secure it in place. 3. Remove masking tape from overhead console. ➢ Instructions continue on Slide #22 AQA Work instruction 2022MY WRX Interior Mirror A/D with Home Link Release Date: 1/11/2022 Revision: B 3/16/2022 Reassemble W/EyeSight 2022MY WRX Interior Auto Dimming Compass Mirror Port Installation Instructions 1 Do Not Overtighten Screws 2 3 3/16/2022 AQA Work instruction 2022MY WRX Interior Mirror A/D with Home Link Release Date: 1/11/2022 Revision: B 14 Interior Auto Dimming Compass Mirror with HomeLink on models without EyeSight™ Slides 14-24 2022MY WRX Interior Auto Dimming Compass Mirror Port Installation Instructions 15 Inspect the Non-EyeSight AD Compass Mirror with HomeLink to ensure no damage or part defects: AQA Work instruction 2022MY WRX Interior Mirror A/D with Home Link Release Date: 1/11/2022 Revision: B 3/16/2022 Kit Contents A) AD Compass Mirror With HomeLink. Manuel Transmission Models without EyeSight Only Note: The Non-EyeSight AD Compass Mirror with HomeLink utilizes a high beam assist sensor incorporated into the mirror assembly. A 2022MY WRX Interior Auto Dimming Compass Mirror with HomeLink Port Installation Instructions Part Number: H501SVC100 Carefully remove the negative battery cable from the battery stud only. Do not allow the negative cable accidentally ground during the accessory installation. Open the hood and use the prop rod to hold the hood in the open position. While holding the battery sensor in place with one hand, use a ¼” drive ratchet and 10mm socket to remove the negative battery cable from the negative battery stud. Do not remove negative cable from the battery post. Position / protect the negative cable so it cannot accidentally touch body ground or the negative battery terminal. Allow (60) seconds before the next installation step to ensure the airbag power supply is discharged. While disconnecting the negative battery cable from the stud, hold the battery sensor in place with one hand while loosening the 10mm hex nut that secures the cable to the sensor. This will help support the sensor to prevent damage and also prevent the assembly from rotating on the battery post causing a poor connection. Battery Terminal Stud Removal AQA Work instruction 2022MY WRX Interior Mirror A/D with Home Link Release Date: 1/11/2022 Revision: B 3/16/2022 16 2022MY WRX Interior Auto Dimming Compass Mirror Port Installation Instructions 17 1. Place protection over the RH or LH side sill/door jam when preparing to perform work inside vehicle. Note: If you are working on the LF side apply the same protection. 2. Place protection center dash and shifter plate trim. AQA Work instruction 2022MY WRX Interior Mirror A/D with Home Link Release Date: 1/11/2022 Revision: B 3/16/2022 Preparation LH RH 2022MY WRX Interior Auto Dimming Compass Mirror Port Installation Instructions 3/16/2022 AQA Work instruction 2022MY WRX Interior Mirror A/D with Home Link Release Date: 1/11/2022 Revision: B 18 1. Using a nylon trim tool, carefully remove the wiring upper trim cover from the compass mirror. 2. To separate and remove the lower trim covers, carefully insert a nylon trim tool on an angle where the cover halves meet at the bottom seam. Gently pry apart to disengage the lower retaining claw. Continue to separate the remaining cover claws and remove the covers. Set aside for reinstallation. 2022MY WRX Interior Auto Dimming Compass Mirror Port Installation Instructions 1 Headliner side Lower Cover side 2 Preparation W/O EyeSight Claw Locations Or 3/16/2022 AQA Work instruction 2022MY WRX Interior Mirror A/D with Home Link Release Date: 1/11/2022 Revision: B 19 Preparation W/O EyeSight 1. Unplug the OE compass mirror. 2. Firmly grab the OE compass mirror and remove by rotating and pulling away simultaneously from the windshield mounting button. (Properly recycle/ dispose O.E. mirror) 2022MY WRX Interior Auto Dimming Compass Mirror Port Installation Instructions 1 2 Twist and pull to release 20 AQA Work instruction 2022MY WRX Interior Mirror A/D with Home Link Release Date: 1/11/2022 Revision: B 3/16/2022 Installation W/O EyeSight 1. Apply protective masking tape on the High Beam Assist sensor. 2. Install the A/D Compass Mirror with HomeLink by aligning the mirror retention clips with the windshield mirror button and pressing against the mirror to seat the mirror. 3. Rotate the mirror until properly aligned with the reference notch shown. 4. Plug in the AD Compass Mirror with HomeLink. (Confirm connection with push-pull method) 2022MY WRX Interior Auto Dimming Compass Mirror Port Installation Instructions 1 2 3 4 Top of mirror button 3/16/2022 AQA Work instruction 2022MY WRX Interior Mirror A/D with Home Link Release Date: 1/11/2022 Revision: B 21 1. Remove protective tape from high beam assist sensor. 2. Reinstall lower mirror trim covers and ensure all claws fully engaged. 3. Reinstall the upper mirror trim cover. Ensure trim cover is fully seated. 2022MY WRX Interior Auto Dimming Compass Mirror Port Installation Instructions Installation W/O EyeSight 2 1 3 Claw Locations 3/16/2022 AQA Work instruction 2022MY WRX Interior Mirror A/D with Home Link Release Date: 1/11/2022 Revision: B 22 Reassemble 1. Remove vehicle protection. 2. Place mirror operation information document in glove box. 2 1 RH RH LH 2022MY WRX Interior Auto Dimming Compass Mirror Port Installation Instructions Re-connect the negative cable by reinstalling the saved 10mm nut on the stud. Use a ¼” drive torque wrench and a 10mm socket, tighten the cable nut to 66 Inch Lbs. while holding the sensor to prevent damage and prevent the assembly from rotating on the battery post. . Torque mark the battery stud While connecting the negative battery cable to the stud, hold the battery sensor in place with one hand while torqueing the 10mm hex nut that secures the cable to the sensor. This will help support the sensor to prevent damage and prevent the assembly from rotating on the battery post causing a poor connection. Carefully reinstall the negative battery cable to the battery stud only. 3/16/2022 AQA Work instruction 2022MY WRX Interior Mirror A/D with Home Link Release Date: 1/11/2022 Revision: B 23 2022MY WRX Interior Auto Dimming Compass Mirror Port Installation Instructions 3/16/2022 AQA Work instruction 2022MY WRX Interior Mirror A/D with Home Link Release Date: 1/11/2022 Revision: B 24 2022MY WRX Interior Auto Dimming Compass Mirror Port Installation Instructions Function Check • Ensure the mirror is properly tightened to the windshield (CVT Models). Torque value 15.0-inch lbs. (13.3 – 17.7-inch lbs. ). • Ensure the battery negative terminal cable is properly reconnected. (Negative battery stud nut torque 5.5ft-lbs (66 in-lbs.). • Ensure the Bolt / Screw access cover is properly re-installed with no gaps around the panel (CVT Models). • Ensure the overhead console cover is properly re-installed with no gaps at the headliner with no damage or chipped edges (CVT Models). • Ensure the wiring cover (CVT Models) and mirror trim covers (6MT Models) are properly installed, seated properly at the mirror base and around the mirror connector. • Turn the Ignition to the “ON” position and cover the interior mirror light sensor and ensure the interior mirror dims accordingly. • With your foot on the brake pedal, put the gear selector in “R” mode and ensure the mirror un-dims. • Ensure map lights turn on and off, door switch functions on and off and telematics illuminates (w/a). • Ensure no soil marks or smudges are present in the installation area, etc. Clean as required. • Ensure the mirror glass and windshield glass around the installation area is clean and the factory sticker is left in place on the mirror. 25 AQA Work instruction 2022MY WRX Interior Mirror A/D with Home Link Release Date: 1/11/2022 Revision: B 3/16/2022 2022MY WRX Interior Auto Dimming Compass Mirror Port Installation Instructions Check Your Work 3/16/2022 26 Document History Revision Date Slide# Description Author A 1/11/2022 N/A Original Release RM B 3/16/2022 18, Multiple Slide 18: Improved mirror trim removal method on non-EyeSight models. Multiple: minor photo and verbiage updates. RM AQA Work instruction 2022MY WRX Interior Mirror A/D with Home Link Release Date: 1/11/2022 Revision: B 2022MY WRX Interior Auto Dimming Compass Mirror Port Installation Instructions
**************************************************************************************************************
SEOCONTENT-END
This product presentation was made with AAWP plugin.