Loose Fitting A-Pillar – Design Change – 2019-2021 Subaru Forester

NHTSA ID Number: 10201808

Manufacturer Communication Number: 12-225-21

Summary

This bulletin announces the design changes made to the A-pillar trim panels and their associated retaining (tether) clips.

 


NUMBER: 12-225-21
DATE:
  09/24/21

 

INTRODUCTION:

This bulletin announces the design changes made to the A-pillar trim panels and their associated retaining (tether) clips. The trim panel has been enhanced to work in conjunction with a new twopiece retaining clip. These changes were introduced to address some concerns of the A-pillar trim panel coming loose. If this concern is experienced, replace the trim panel(s) along with the associated retaining clip(s).

 

PRODUCTION CHANGE INFORMATION

These changes were introduced into production starting with VIN MH519540.

 

PART INFORMATION:

 

REMINDER: Always order the most up-to-date replacement parts based on the specific VIN being repaired.

Part DescriptionPart Number
TRIM PANEL-A PILLAR, UPPER RIGHT94010SJ001ME
TRIM PANEL-A PILLAR, UPPER LEFT94010SJ011ME
CLIP909150050

 

SERVICE PROCEDURE / INFORMATION:

REMINDER:  Customer satisfaction and retention starts with performing quality repairs.

The service procedures for the A-pillar remain unchanged.  Always refer to the applicable Service Manual and review the full requirements of the repair being performed.  The Service Manual procedures contain information critical to performing an effective repair the first time, every time.  This includes but is not limited to important SAFETY precautions, proper inspection criteria, necessary special tools, required processes and related one-time-use parts needed for a complete and lasting repair.

Refer to the applicable Service Manual: Body & Electrical/WIRING SYSTEM > EXTERIOR/INTERIOR TRIM > Upper Inner Trim

NOTES:

  • If the tether clip is damaged in away it must be replaced with a new clip.
  • Refer to the applicable Service Manual and review: General Description > Repair Contents > Action required before & after Battery Disconnect. Additionally, record any stored seat position(s) before proceeding. Relearn any seat position memory after work is complete. If the power rear gate (PRG) height has been customized, that position must also be noted and relearned.
  • Whenever reconnecting the ground cable terminal to the battery sensor, torque to 7.5Nm (5.5ft.lbs. or 66inch-lbs.) while supporting the sensor with the other hand as outlined in the applicable Service Manual under: STARTING/CHARGING SYSTSEMS > Battery Sensor.

 


3 Affected Products

Vehicle

MAKEMODELYEAR
SUBARUeBay logoFORESTER2019-2021

 


1 Associated Document

Manufacturer Communications

NUMBER: 12-225-21
DATE: 09/24/21

MC-10201808-0001.pdf 1098.137KB

 


 

SaleBestseller No. 1
GOOACC 100PCS 7mm 8mm 10mm Compatible with Subaru Push Type Retainer Fasteners Rivets Clips OEM Upgrade for 90914-0007, 90913-0067 & 90914-0051 + Bonus Fastener Remover
  • 40pcs 90914-0007 Bumper, Engine Cover, Fender & Grille Push-Type Retainer for SubarueBay logo Baja, Forester, Impreza, Legacy, Outback & Tribeca 2011 - 2000
  • 30pcs 90913-0067 Engine Cover and Fender Liner for SubarueBay logo B9, Forester, Legacy, Outback & Tribeca 2005 -
  • 30pcs 90914-0051 Front Bumper & Quarter Panel Push-Type Retainer for SubarueBay logo Impreza, Legacy, Outback & Tribeca 2011 - 2005
  • FITS VARIOUS SUBARUeBay logo MODELS - The clips fit selected SubarueBay logo as well some other car brands.
  • Premium OEM Upgraded Quality and Durable —Made of Premium Auto Grade Nylon:PA66(Not Ordinary Cheap Nylon),solid like metal.
Bestseller No. 2
121pcs 7mm 8mm 9mm 10mm for Subaru Push-Type Bumper Fender Retainers Clips
  • 30Pcs 90914-0007 Push-type clip replace for Ascent, B9 Tribeca, Baja, BRZ, Crosstrek, Forester, Impreza, Legacy, Outback, Tribeca, WRXeBay logo, WRXeBay logo STIeBay logo, XV Crosstrek work on Bumper, Engine Cover, Fender & Grille
  • 30Pcs 90914-0065 body clips replace for Ascent, BRZ, Crosstrek, Forester, Impreza, Legacy, Outback, WRXeBay logo, WRXeBay logo STIeBay logo, XV Crosstrek work on Front Fender Liner, Engine Cover, Hood & Quarter Panel
  • 30Pcs 90914-0051 Front bumper & quarter panel push-type retainer compatible with BRZ, Legacy, Outback, Tribeca, Head Diameter: 20mm, Hole Size: 7mm, Stem Length: 9mm
  • 30Pcs MR200300 Rocker molding push-type retainer compatible with Ascent, Crosstrek, Forester, Impreza, Legacy, Outback, Tribeca, WRXeBay logo, WRXeBay logo STIeBay logo, XV Crosstrek, Fits Into 9mm Hole
  • 4 different sizes in the bag each one came in handy and it came with 1 tool, exact match for the factory clips. also must have for most Japanese cars repair or upgrade like honda & nissan and toyota
Bestseller No. 3
Niteguy 390Pcs Subaru Car Plastic Rivets Fasteners Push Retainer Kit,18 Most Popular Sizes Auto Push Pin Rivets, for Subaru Toyota Body Interior and Exterior Retainer Fastener Clip
  • 【18 Most Popular Sizes】390Pcs auto push retainer Clips,Includes 18 Sizes of SubarueBay logo Body Interior and Exterior Retainer Fastener Clip, These Are Reliable Replacement for the Original Part That had Missing or Failed Due to Fatigue.This push clip is suitable for most SubarueBay logo Forester, BRZ, Impreza, Legacy, Outback, WRXeBay logo, Baja, Tribeca etc.
  • 【High Quality Material】Retainer clips are made of heavy-duty nylon material, anti-wear, vibration resistant, anti-corrosion, would not break or crack easily. Comes with a plastic box for organized storage. Compact size, convenient to store or carry with in your car.Allows to freely DIY your vehicle accessories at anytime you wanted.
  • 【Extra Car Fastener Remover】The kit comes with extra different models of removers. Enables you to quickly and easily remove door panel trim clips and trim clips without damaging them. Easy access to restricted areas.
  • 【Applicable Scene】 The SubarueBay logo auto push clips are widely used for front fender liner, engine cover, door trim clips, bumper clips,interior accessories and splash shield retainers replacement.All the necessary retainers for exact replacement of old and broken retainer.
  • 【Customer Service】100% SATISFACTION:If you are not satisfied with our car body clips and trim removal tools,please contact us,we will try our best to solve your problem.
Bestseller No. 4
OAUTOO 190pcs for Subaru Body Interior and Exterior Retainer Fastener Clip Assortment 19 Most Popular Sizes & Applications
  • 🔧 Multiple Solutions- Includes 19 Sizes of SubarueBay logo Body Interior and Exterior Retainer Fastener Clip, Total 190 Pieces. These Are Reliable Replacement for the Original Part That had Missing or Failed Due to Fatigue.
  • ✅ Durable Construction - These Clips are Made from Quality Nylon Materials to Ensure Reliable Performance and Long Service Life.
  • 🚗 Fits Most SubarueBay logo Models, Including Hood Insulation Retainer, Front & Rear Bumper Push-Type Retainer, Front Fender, Bumper & Quarter Panel Push-Type Retainer, Front Fender Liner, Engine Cover, Hood & Quarter Panel Push-Type Retainer, Nylon Nut, Fender Liner, Duct & Lower Moulding Push-Type Retainer, Garnish Moulding Retainer, Cowl Vent Push-Type Retainer, Trim Board Retainer, Engine Cover and Fender Liner Retainer, Screw Grommet with Sealer, Cowl Panel Vent Cap.
  • ✉ Part Number: SubarueBay logo 🔷 1 #OE: 909140059; 🔷 2 #OE: 909130013; 🔷 3 #OE: 46064AE000; 🔷 4 #OE: 59130AA000; 🔷 5 #OE: 909140065; 🔷 6 #OE: 661179000; 🔷 7 #OE: 909140068; 🔷 8 #OE: 909130051; 🔷 9 #OE: 909130146; 🔷 10 #OE: 909140063; 🔷 11 #OE: 909130115; 🔷 12 #OE: 909130067; 🔷 13 #OE: 909130074; 🔷 14 #OE: 91084AA010; 🔷 15 #OE: 909140055; 🔷 16 #OE: 91486KJ010, 91486-FL020; 🔷 17 #OE: 57728AC090; 🔷 18 #OE: 909140007.
  • ☺ Please Check the Part Number and Installation Position Information on the Picture Before Purchase.
Bestseller No. 5
Rexka 40pcs 10mm Hole Bumper Engine Cover Fender & Grille Clips Compatible with Subaru 909140007 Baja Forester Impreza Legacy Outback Tribeca 2011-2000

 


This product presentation was made with AAWP plugin.

Leave a Comment

Share to...