Accessory Installation Guide
| 2024MY Impreza and Crosstrek Rear Gate Assistance Handle | F6010FN000 |
Installation Manual
Genuine Part Number: F6010FN000
Applicable Model: CROSSTREK (GU) Type A~
This manual describes how to install the Rear Gate Assistance Handle.
Precautions
1. Turn the ignition switch off and securely apply the parking brake before installing this product.
2. During the installation work, be careful to avoid being injured by vehicle edges.
3. Be sure to disconnect the (−) terminal of the battery during the installation work.
4. Apply anti-scratch tape to the outer edges of the vehicle parts and the tools to prevent scratches.
Tools
Clip remover, center punch, Phillips-head screwdriver, electric drill, drill bit (3mm), hole saw (30mm), diagonal cutting pliers, end cutting pliers, curing tape, degreaser, cloth tape, rag
Installation
1. Removal of vehicle parts
(1) Open the rear gate and remove the vehicle parts in numerical order.
❶Rear Gate Upper Panel Trim
❷Rear Gate Upper Panel Side Trim
(Right-hand, Left-hand)
(2) Remove the vehicle parts in numerical order.
❸Rear Gate Lower Cap
(For vehicles with a light, disconnect the connector)
❹Rear Gate Trim Lower Fixing Clips
Caution
- Use a Phillips-head screwdriver for removal.
- Store the removed clips carefully as they will be reused.
❺Rear Gate Lower Trim
2. Preparation of vehicle parts
(1) Remove the clip in the position shown in the figure on the left behind the Rear Gate Lower Trim.
Caution
- There is a SUBARU engraving near the clip to be removed.
Be careful not to mistake the position. - Do not reuse the removed clip; please discard it.
(2) ut the ribs of the clip hole with diagonal/end cutting pliers.
(3) Mark the center of the clip hole with a center punch.
(4) Drill a hole at the position marked in (3) using an electric drill (3mm).
Caution
- To avoid unnecessary drilling, wrap the drill bit with cloth tape to limit the hole depth to 5mm.
- The drill should be aligned perpendicular to the drilling surface.
(5) Widen the hole drilled in (4) on the front side of the Rear Gate Lower Trim using a hole saw (30mm).
Caution
- To avoid unnecessary cutting, wrap the drill bit with cloth tape to limit hole depth to 5mm.
- The hole saw should be aligned perpendicular to the cutting surface.
(6) Remove the burrs around the hole with end cutting pliers.
Caution
- Be sure to remove any burrs. If burrs are not sufficiently removed, the ②Cap or ③Retainer may not attach correctly due to gaps or looseness.
(7) Attach the ②Cap and ③Retainer to the Rear Gate Lower Trim.
Caution
- Once the ②Cap and ③Retainer are attached, they cannot be removed.
- When attaching, use 2 notches as reference. If it does not go in, check that the ②Cap does not rotate.
3.Installing the grip
(1) Referring to the figure on the left and after degreasing the mounting position of the ⑤Bracket, remove the film from the double-sided tape for the ⑤Bracket, align the positions of the vehicle panel hole and the ⑤Bracket hole and attach them together.
(2) Attach the ①Grip into the ⑤Bracket hole using a SEMS bolt.
Caution
- Attach so that the front side of the eyelet is on the SEMS bolt side.
- Refer to the figure on the left and mount the ① Grip, paying attention to its orientation.
(3) Move the Rear Gate Lower Trim closer and pull the ①Grip out through the slot in the ②Cap to restore it to its original position.
Caution
- When restoring the Rear Gate Lower Trim, be careful that the ①Grip does not get caught in it.
Restore vehicle parts
Refit the removed vehicle parts back to their original position.
F6010FN000
2022/9/1
2024MY Crosstrek and Impreza Rear Gate Assist Handle User Manual
F6010FN000_OM
F6010FN000
REAR GATE ASSISTANCE HANDLE
User Manual
To customers
Thank you for purchasing the Subaru Genuine Rear Gate Assistance Handle.
Request
1. Read this manual before use and always use the product correctly.
2. Always keep this manual available for reference.
3. In order to avoid improper installation, please request that the installation work be performed by Subaru Distributor or a seller designated by a Subaru Distributor.
Precautions
1. If the rear gate assistance handle becomes dirty, wipe it with a cloth moistened with water and then dry it with a soft cloth.
2. This product is an auxiliary item used to help with closing the back door of the vehicle. Hanging from it or hanging objects from it can not only damage it, but can also lead to vehicle damage and accidents.
To installers
This manual describes how to use the Rear Gate Assistance Handle.
Request
1. This manual must be given to the customer.
F6010FN000_OM
- [Easy to Use—Work Out of the Box] + [FOXWELL 2026 New Version] FOXWELL NT604 Elite scan tool is the 2026 new version from FOXWELL, designed for car owners who want to figure out the cause of issues before fixing car problems by scanning common systems like ABS, SRS, engine, and transmission. The NT604 Elite obd2 scanner diagnostic tool comes with the latest software—no need to waste time downloading software first. Plug the scanner into the OBDII port with OBDII cable to start the diagnosis.
- [Affordable] + [Reliable Car Health Monitor] Will you be confused what happens when the warning light of ABS/SRS/transmission/check engine flashes? Instead of taking your cars to dealership, this FOXWELL scanner will help you do a thorough scanning and detection for your cars and pinpoint the root cause. Note：The device is a diagnostic tool, not a repair tool. To turn off a warning light, you must first physically repair the issue causing it. Only then can the scanner be used to clear the corresponding fault code.
- [5 in 1 Car Diagnostic Scanner] Compared with obd scanners (50-100), NT604 Elite code scanner not only includes their OBDII diagnosis but also serves as ABS/SRS scanner, transmission and check engine code reader. When it’s an odb2 scanner, you can use it to check if your car is ready for annual test through I/M readiness menu. In addition, live data stream, built-in DTC library, data play back and print, all these features are a big plus for it. Note: doesn't support maintenance functions like reset or relearn. For the SRS system, NT604 Elite can read and clear common fault codes not caused by a crash, but crash/collision data cannot be cleared.
- [Fantastic AUTOVIN] + [No extra software fee] Through the AUTOVIN menu, this NT604 Elite car scanner allows you to get your V-IN and vehicle info rapidly, no need to take time to find your V-IN and input one by one. What's more, the NT604 Elite ABS SRS scanner supports 60+ car brands from worldwide (America/Asia/Europe). You don’t need to pay extra software fee. AUTOVIN may not work on some older vehicles or certain vehicle brands. If AUTOVIN fails, please input the vin code manually or go to the Diagnostic Menu to select your vehicle model.
- [Solid protective case KO plastic carrying bag] + [Lifetime update] Almost all same price-level car scanner diagnostic tool only offers plastic bag to hold the scanner.However, NT604 Elite automotive scanner is equipped with solid protective case, preventing your obd2 scanner from damage. Then you don’t need to pay extra money to buy a solid toolbox.
- 【Reset ABS/SRS/Transmission/Engine Lights】 More than an check engine code reader, OBDMATE OM901 obd2 scanner performs comprehensive diagnostics for the 4 most-used systems (ABS/SRS/Engine/Transmission). It quickly clears fault codes, turns off warning lights, read data stream and auto VIN.
- 【3.5" Handheld Scanner with 4 System Diagnose】 3.5" Super large TFT screen equipped displays an intuitive menu and clear readings of various sensors from ABS, SRS, ECM and TCM
systems. It arrived with a silicone protective case and hard-shell carrying case, ensuring long-lived durability and drop resistance. The car diagnostic tool is plug-to-play designed, plug it and get diagnosis started without any batteries or updates required. - 【One-Click I/M Readines&Full OBD2 Functions】 Press F1 to get an intuitive corloured form about whether various emissions-related systems on the vehicle are operating properly. Help you get smog-check ready quickly. OM901 car scanner supports all essential OBD2 functions you need: read & clear codes, view freeze frame, read I/M readiness, retrieve VIN, live data stream (with graphing display), O2 sensor test, onboard monitoring mode, and EVAP leak test.
- 【Battery Voltage Check&DLC Pin Test】 It allows you to monitor battery health by testing current battery voltage. Plus, this obd2 diagnostic tool features DLC 16-PIN test to check current voltage of every pin.
- 【Automotive Scanner Diagnostic Kit】 The package comes with 1 car scanner, 1 USB-type c cable, 1 hard storage bag and 1 user manual(en). Free to update without any hidden fees. 5 languanges available in setting including English, French, Italian, German and Espanish. Valuable and Portable, making it a great tool kit for car owners, DIY enthusiasts, and professional mechanics.
systems. It arrived with a silicone protective case and hard-shell carrying case, ensuring long-lived durability and drop resistance. The car diagnostic tool is plug-to-play designed, plug it and get diagnosis started without any 
- [Diagnose Like a Pro] BlueDriver Pro is a professional OBD2 scanner and diagnostic tool that helps you scan, understand, and clear vehicle trouble codes with confidence. Turn your phone into a powerful car diagnostic scanner—no guesswork, no unnecessary repairs.
- [Read and Clear More Codes Than Ever] Read and clear more codes than basic car code readers. Access enhanced diagnostics for Check Engine, ABS, SRS, Airbag, TPMS, Transmission.
- [Verified Fixes and Real-Time Data] Get unlimited, technician-verified repair reports matched to your VIN, with definitions, causes, and confirmed fixes. Monitor live vehicle data as you drive, view freeze frames, check smog readiness, and analyze Mode 6 test results.
- [Wireless & Bluetooth Enabled] - Say goodbye to wires. BlueDriver connects with Bluetooth via your phone/tablet to a sensor that plugs into your car's OBDII port. Get all of the capabilities of an expensive code reader & scan tool without any annoying wires.
- [Broad Make & Model Coverage] Strong support for GM, Ford, Stellantis (RAM, Jeep, Chrysler), Toyota, Honda, Nissan, Mazda, Subaru, Hyundai, Mercedes-Benz, BMW, and VW.
- ✔️【Professional SRS Reset for 1994-2003 BMW】 Designed specifically for classic BMW models (1994-2003). This B800 scanner reads & clears SRS airbag fault codes, turns off the warning light, and saves you a costly dealer visit. Confirmed compatible with: E36, E46 (EXCEPT 2001 330i), E34, E38, E39, Z3, and X5 (E53). NOT compatible with any BMW built before 1994 or after 2003.
- ✔️【Important: Two Different Connection Ports – Read Before Use】 To avoid “not working” issues, please note: For 1994–2000 BMWs (most E36, E34, Z3, early E39), the SRS diagnostic port is a round 20-pin connector under the hood. You MUST use the included 16-pin to 20-pin adapter cable. For 2000–2003 models (late E46, E39, X5), use the standard OBD-II port inside the cabin. Incorrect connection is the #1 reason for “incompatibility” reports.
- ✔️【Read & Clear Fault Codes in Minutes】 Quickly diagnose why your SRS light is on. The scanner accurately reads fault codes from airbag and seatbelt pretensioner systems. With one button press, clear the codes and reset the SRS warning light in seconds. No expensive dealer tools needed.
- ✔️【User-Friendly for DIYers – No Mechanic Required】 Easy operation with an intuitive button layout: ‘Enter’ to confirm, ‘Scroll’ to navigate. The clear LCD screen shows results instantly. Includes a step-by-step manual (revised for clarity) to guide you through the entire reset process.
- ✔️【Reliable Support with 1-Year Warranty】 We stand behind the quality of our B800 scanner. It comes with a 1-Year Hassle-Free Warranty. If you have any questions or need support, please contact us with your Order ID, and our dedicated team will assist you promptly.
- OBD2 SCANNER FOR ALL SYSTEMS – The INNOVA SD35 is a tablet-based OBD2 scanner designed for advanced diagnostics. Read and clear check engine light, ABS, SRS, and TPMS codes, plus test your car battery and alternator to prevent unexpected failures. Vehicle coverage may vary. Please use Innova’s Coverage Checker to verify compatibility.
- ALL-SYSTEM DIAGNOSTICS & LIVE DATA – Unlike basic code readers, this OBD2 scanner for all vehicles scans engine, transmission, ABS, SRS, and more. Get real-time live data, including RPM, fuel trims, temperature readings, and oxygen sensor performance.
- OBD2 TABLET WITH USER-FRIENDLY INTERFACE – This automotive scan tool features a high-resolution display, making vehicle diagnostics faster and easier.
- ADVANCED TPMS, OIL RESET & SERVICE FUNCTIONS – Perform TPMS sensor checks, oil light reset, and other service resets with ease This professional diagnostic tool provides comprehensive vehicle maintenance capabilities in one device.
- WIDE VEHICLE COVERAGE (1996 & NEWER CARS & TRUCKS) – This OBD2 scanner Bluetooth tablet is compatible with Toyota, Ford, Honda, Chevrolet, Nissan, Dodge, and more. However, feature coverage may vary. Please use Innova's Coverage Checker to verify coverage.
SEOCONTENT-START
１ ① ② ③ ④ ⑤ ① № Part Name ② ③ Grip Cap Retainer 1 １ １ ④ SEMS bolt (M6×20) １ This manual describes how to install the Rear Gate Assistance Handle. 1. Turn the ignition switch off and securely apply the parking brake before installing this product. 2. During the installation work, be careful to avoid being injured by vehicle edges. 3. Be sure to disconnect the (−) terminal of the battery during the installation work. 4. Apply anti-scratch tape to the outer edges of the vehicle parts and the tools to prevent scratches. REAR GATE ASSISTANCE HANDLE Installation Manual To installers Components Tools Clip remover, center punch, Phillips-head screwdriver, electric drill, drill bit (3mm), hole saw (30mm), diagonal cutting pliers, end cutting pliers, curing tape, degreaser, cloth tape, rag Precautions 1. Before installing this product, please ensure to read this manual and carry out proper installation. Request △00 Qty. ⑤ Bracket (with double-sided tape) １ Distributor Co., Ltd. 2022/9/1 D e t a i l s D a t e : Revision History △ △00 Created Double-sided tape Genuine Part Number: F6010FN000 Applicable Model: CROSSTREK (GU) Type A~ ２ 1. Removal of vehicle parts 2.Preparation of vehicle parts (1) Remove the clip in the position shown in the figure on the left behind the Rear Gate Lower Trim. (2) ut the ribs of the clip hole with diagonal/end cutting pliers. (3) Mark the center of the clip hole with a center punch. (2) Remove the vehicle parts in numerical order. ❸Rear Gate Lower Cap (For vehicles with a light, disconnect the connector) ❹Rear Gate Trim Lower Fixing Clips (1) Open the rear gate and remove the vehicle parts in numerical order. ❶Rear Gate Upper Panel Trim ❷Rear Gate Upper Panel Side Trim (Right-hand, Left-hand) Caution ・There is a SUBARU engraving near the clip to be removed. Be careful not to mistake the position. ・Do not reuse the removed clip; please discard it. Caution ・Use a Phillips-head screwdriver for removal. ・Store the removed clips carefully as they will be reused. Installation ❺Rear Gate Lower Trim ❸ ❺ ❷ ❶ ❷ [Fig.2] [Fig.1] SUBARU engraving marking Clip Rib cut [Fig.3] Rear Gate Lower Trim ❹Clip ❹Clip Back side of Rear Gate Lower Trim :Claw position :Claw position :Clip position ３ (6) Remove the burrs around the hole with end cutting pliers. (5) Widen the hole drilled in (4) on the front side of the Rear Gate Lower Trim using a hole saw (30mm). (7) Attach the ②Cap and ③Retainer to the Rear Gate Lower Trim. (4) Drill a hole at the position marked in (3) using an electric drill (3mm). Caution ・Be sure to remove any burrs. If burrs are not sufficiently removed, the ②Cap or ③Retainer may not attach correctly due to gaps or looseness. Caution ・Once the ②Cap and ③Retainer are attached, they cannot be removed. ・When attaching, use 2 notches as reference. If it does not go in, check that the ②Cap does not rotate. Caution ・To avoid unnecessary drilling, wrap the drill bit with cloth tape to limit the hole depth to 5mm. ・The drill should be aligned perpendicular to the drilling surface. Caution ・To avoid unnecessary cutting, wrap the drill bit with cloth tape to limit hole depth to 5mm. ・The hole saw should be aligned perpendicular to the cutting surface. Back side of Rear Gate Lower Trim Front side of Rear Gate Lower Trim Front side of Rear Gate Lower Trim ②Cap ②Cap Burr ③Retainer ③Retainer 2 notches Hole saw (30mm) Drilled hole Crosssectional view [Fig.5] [Fig.6] [Fig.7] Electric drill (3mm) Marking position [Fig.4] Back side of Rear Gate Lower Trim Drill Stopper (cloth tape) 5mm Hole saw tip Hole saw Stopper (cloth tape) 5mm ４ Caution ・When restoring the Rear Gate Lower Trim, be careful that the ①Grip does not get caught in it. (3) Move the Rear Gate Lower Trim closer and pull the ①Grip out through the slot in the ②Cap to restore it to its original position. Caution ・Attach so that the front side of the eyelet is on the SEMS bolt side. ・Refer to the figure on the left and mount the ① Grip, paying attention to its orientation. (2) Attach the ①Grip into the ⑤Bracket hole using a SEMS bolt. Refit the removed vehicle parts back to their original position. Restore vehicle parts 3.Installing the grip (1) Referring to the figure on the left and after degreasing the mounting position of the ⑤Bracket, remove the film from the double-sided tape for the ⑤Bracket, align the positions of the vehicle panel hole and the ⑤Bracket hole and attach them together. ⑤Bracket ⑤Bracket (Double-sided tape) ⑤Bracket (Attaching position) Vehicle panel hole ①Grip ②Cap Pull the ①Grip out through the slot in the ②Cap Trim rear gate lower Vehicle panel (opening) Rear gate [Fig.8] [Fig.10] ⑤Bracket (Mounting hole) Eyelet front side ①Grip ④SEMS bolt [Fig.9]
**************************************************************************************************************
**************************************************************************************************************
SEOCONTENT-END
This product presentation was made with AAWP plugin.