Accessory Installation Guide
| 2024MY Crosstrek Lower Door Cladding (Door Under Garnish) | J1010FN800 |
Installation Manual
This manual describes how to install the Door Under Garnish.
Request
Before installing this product, please ensure to read this manual and carry out proper installation.
Precautions
1. When installing this product on a car, park the car on a flat place and securely apply the parking brake before carrying out the work.
2. Before starting the installation work, use a neutral detergent (or degreasing agent) and waste cloth to remove dirt adhering to the car’s surfaces to which the door under garnish are to be attached, and completely dry the surfaces. Moreover, if sand or mud adheres to the back of the clip insertion holes, etc., then clean the contaminated sections.
3. Install the door under garnish before applying a car body coating treatment. When installing them on a coated car, remove the coating in the areas where the double-sided tape is to be applied before carrying out the installation work.
4. During the installation work, pay careful attention not to damage the car with tools, etc.
5. The purpose of this document is to illustrate explanations common to installation work on the left and right sides. Check the shape of the components to be installed before carrying out the work.
6. When the air temperature is 15℃ or lower, use a dryer to warm up this product and the surfaces of the car where the double-sided tape is to be applied to 30℃ to 50℃ or thereabouts. Avoid using an industrial dryer.
7. The double-sided tape attached to this product does not adhere to the surfaces unless it is adequately pressed. Moreover, reattaching the product significantly reduces the adhesive strength of the tape; therefore, properly position the product before attaching it to the car.
8. The adhesive strength of the double-sided tape gradually increases after it is applied to the car. Avoid washing the car within 24 hours after attachment . When washing and waxing the car are necessary on the day of the attachment, leave the car as is for at least one hour and subsequently cover the door under garnish guards with tape, etc. to prevent water from penetrating into areas where the double-sided tape i s applied. Further, be careful not to apply an excessive force to the guards.
9. When blowing air on this product after it is attached to the car, maintain a distance of at least 300 mm between the exhaust port of the blower and the product. Insufficient distance may cause this product to peel.
10. When a car has undergone a body coating treatment including glass coating, this product cannot exhibit its original adhesive performance. Please confirm whether or not a body coating treatment is applied to the car. Moreover, ensure to remove dirt, oil, grease, etc. adhering to the surface on which the product is to be attached, and also ensure to adequately pressure bond it to the car.
<<How to remove a body coating film and confirm the removal>>
– Use a fine-grained compound agent (so as not to affect the car’s paint) to rub the coating film off the area on which the product is to be attached.
– After polishing the area, spray water on it. You can confirm that the coating film has been removed when there is no repelling of water on the area.
Door Under Garnish
Genuine Part Number : J1010FN800
Applicable Model : 2024MY～CROSSTREK
Installation procedure
1. Cleaninng/Degreasing
(1) Clean, degreas, and dry the shaded area of the Door Panel with a degreasing agent.
Caution
If rainwater is attached, wipe it dry with a dry cloth.
Insufficient wiping and drying can cause the product to come off.
2. Preparing to install the Door Under Garnish RR
(1) Part of the double-sided tape liners on the ④ Door Under Garnish RR LH is peeled off and fixed with masking tape. ( ▼ 6 places )
Caution
Do not peel off the double-sided tape liner more than necessary.
Double-sided tape clings to the vehicle, which hinders positioning.
3. Install the Door Under Garnish RR
(1) Open the front door and temporarily fix the ④ Door Under Garnish RR LH with masking tape according to the rear door shape, referring to the figure on the left.
(2) Pull out the double-sided tape liner in the order of to referring to the figure on the left, and crimp it.
Caution
Please follow the order of removing the release paper. The position may shift during installation.
Caution
To crimp the double-sided tape, press it with a force of 49N(5kgf) for about 10 seconds.
4. Preparing to install the Door Under Garnish FR
(1) Apply masking tape to the top of the ④ Door Under Garnish and cut at the split position of the door.
Caution
Apply masking tape straight.
(2) Part of the double-sided tape liners on the ③ Door Under Garnish FR LH is peeled off and fixed with masking tape. ( ▼ 6 places )
5. Install the Door Under Garnish FR
(1) Open the front door and temporarily fix the ③ Door Under Garnish FR LH with masking tape according to the front door shape, referring to the figure on the left.
(2) Pull out the double-sided tape liner in the order of to referring to the figure on the left, and crimp it.
Caution
Please follow the order of removing the release paper. The position may shift during installation.
Caution
To crimp the double-sided tape, press it with a force of 49N(5kgf) for about 10 seconds.
This is the end of the work.
Inspection procedure
Make sure the clips are attached, the adhesion of the double-sided tape, and make sure that there is no rattling.
Make sure there are no scratches or stains.
There shall be no significant gaps or separation.
J1010FN800
2022/08/01
- PREPS SURFACE: Pre-waxing glaze that prepares the surface for wax while offering deep reflections and high gloss.
- BEST CAR GLOSS: Conditioning oils add depth of color and maximum gloss prior to waxing, especially on dark colored cars
- REMOVE SWIRLS: Quickly and gently removes fine swirls and towel marks for mirror-like reflections
- SAFE FOR CLEAR COATS: Safe and on all glossy paints, including clear coats
- FLEXIBLE APPLICATION: Safe and effective by hand or dual action polisher like Meguiar's MT300 Dual Action Polisher
- BUFF OUT IMPERFECTIONS: Meguiar's Ultimate Compound removes scratches, swirls & oxidation for a clear, perfect finish
- SHOWROOM SHINE: Advanced car compound removes scratches, swirls, oxidation & water spots and restores color & clarity for a showroom shine in minutes
- CLEAR COAT SAFE: Auto compound safely removes scratches and other defects without hazing on clear coats & all gloss paints. Easy DIY fix by hand or da polisher
- LIKE-NEW SHINE: Meguiar's exclusive micro-abrasive technology quickly removes scratches & restores clarity and shine for a stunning, swirl-free finish.
- FAST & FLAWLESS: Meguiar's Ultimate Compound cuts fast, removes scratches and swirls without hazing, leaving a pro-detailer finish.
- One 16 oz bottle of Nu Finish The Once A Year Car Polish
- Automotive polish that is made up of a series of zinc cross-linking polymer emulsions that help it last longer than any other polish on the market
- Nu Finish car polish can be applied anywhere, even in direct sunlight
- Also an ideal boat polish, motorcycle polish and chrome polish
- The only auto polish tough enough to be called "The Once A Year Car Polish”
- [Gift for Detail-Oriented Car Lovers]: Nu Finish Once a Year Polish and Sealant - advanced ceramic technology that repairs, seals, and protects car's paint for an entire year with just one application
- REPAIRS SCRATCHES AND RENEWS SHINE: Long-lasting auto polish that helps repair fine swirls, scuffs and scratches while renewing the shine on paint and chrome, leaving a glossy, wet finish without any wax
- PREVENTS FUTURE SCRATCHES: Innovative Ceramic Technology forms an effective, durable protective barrier that helps prevent future scratches from forming and delivers extreme water beading for easier maintenance
- NO RUBBING OR BUFFING: Unique liquid polish that requires no rubbing or buffing and can even be applied in direct sunlight, unlike conventional car wax
- THE ONCE A YEAR CAR POLISH AND SEALANT: With just one application, you can polish and protect your car’s paint for an entire year* (*Based on U.S. average automatic car washes per year)
- EASY SCRATCH and SWIRL REPAIR - If your car has light scratches, swirls, or other marks - you can easily fix that with our Scratch & Swirl Remover Kit! Using the included buffer pad, our specially formulated compound will allow you to easily remove and "erase" years of wear and tear from your vehicles paint and overall appearance!
- ULTIMATE PAINT REPAIR- Not only will this remove swirls and scratches, it will restore the gloss and shine of your paint and bring it back to its original brilliance! The special rubbing compound will remove water spots, oxidation and other contaminants from your paint!
- PREMIUM CHEMICALS - We formulate all our products to ensure they are the best! Professional grade, but easy enough for anyone to use! We use only the absolute best chemicals and ensure there are no unnecessary color dyes or scents!
- ADVANCED SOLUTION FOR ALL PAINT TYPES - Car paint scratch repair is safe to use on all paints and colors. You can safely use it on any clearcoat, single stage, or multi stage paint!
- REVOLUTIONARY PRODUCT - This scratch remover for vehicles provides an effortless and secure way to remove scratches.
SEOCONTENT-START
This manual describes how to install the Door Under Garnish. ！ Precautions 1. When installing this product on a car, park the car on a flat place and securely apply the parking brake before carrying out the work. 2. Before starting the installation work, use a neutral detergent (or degreasing agent) and waste cloth to remove dirt adhering to the car’s surfaces to which the door under garnish are to be attached, and completely dry the surfaces. Moreover, if sand or mud adheres to the back of the clip insertion holes, etc., then clean the contaminated sections. 3. Install the door under garnish before applying a car body coating treatment. When installing them on a coated car, remove the coating in the areas where the double-sided tape is to be applied before carrying out the installation work. 4. During the installation work, pay careful attention not to damage the car with tools, etc. 5. The purpose of this document is to illustrate explanations common to installation work on the left and right sides. Check the shape of the components to be installed before carrying out the work. 6. When the air temperature is 15℃ or lower, use a dryer to warm up this product and the surfaces of the car where the double-sided tape is to be applied to 30℃ to 50℃ or thereabouts. Avoid using an industrial dryer. 7. The double-sided tape attached to this product does not adhere to the surfaces unless it is adequately pressed. Moreover, reattaching the product significantly reduces the adhesive strength of the tape; therefore, properly position the product before attaching it to the car. 8. The adhesive strength of the double-sided tape gradually increases after it is applied to the car. Avoid washing the car within 24 hours after attachment . When washing and waxing the car are necessary on the day of the attachment, leave the car as is for at least one hour and subsequently cover the door under garnish guards with tape, etc. to prevent water from penetrating into areas where the double-sided tape i s applied. Further, be careful not to apply an excessive force to the guards. 9. When blowing air on this product after it is attached to the car, maintain a distance of at least 300 mm between the exhaust port of the blower and the product. Insufficient distance may cause this product to peel. 10. When a car has undergone a body coating treatment including glass coating, this product cannot exhibit its original adhesive performance. Please confirm whether or not a body coating treatment is applied to the car. Moreover, ensure to remove dirt, oil, grease, etc. adhering to the surface on which the product is to be attached, and also ensure to adequately pressure bond it to the car. <<How to remove a body coating film and confirm the removal>> – Use a fine-grained compound agent (so as not to affect the car’s paint) to rub the coating film off the area on which the product is to be attached. – After polishing the area, spray water on it. You can confirm that the coating film has been removed when there is no repelling of water on the area. Request Before installing this product, please ensure to read this manual and carry out proper installation. Door Under Garnish Installation Manual -1- Δ00 Distributor Co., Ltd. SUBARU
-2- Genuine Part Number : J1010FN800 Door Under Garnish ① ② 1 ③ ④ ⑤ 1 1 1 1 Door Under Garnish FR RH Cross section gauge Components Tools Installation Completion Illustration ※ Left side of the vehicle No. Part Name Qty ● Masking tape ● Clean cloth ● Dryer ● Scale ● Degreasing agent (recommended nonane) Door Under Garnish RR RH Door Under Garnish FR LH Door Under Garnish RR LH ② ① ③ ④ ⑤ ＦＲ ＲＲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ③ Door Under Garnish FR LH ④ Door Under Garnish RR LH Applicable Model : 2024MY～ CR O S ST R EK -3- ▼ ▼ ▼ ▼ ▼ ▼ Ｂ Ａ Ｃ 10mm Push ＦＲ ＲＲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ Installation procedure Cleaning and degreasing (1) Clean, degreas, and dry the shaded area of the Door Panel with a degreasing agent. 1. Cleaninng/Degreasing If rainwater is attached, wipe it dry with a dry cloth. Insufficient wiping and drying can cause the product to come off. ！ Caution ！ 3. Install the Door Under Garnish RR (1) Open the front door and temporarily fix the ④ Door Under Garnish RR LH with masking tape according to the rear door shape, referring to the figure on the left. 【Part C details】 Do not peel off the double-sided tape liner more than necessary. Double-sided tape clings to the vehicle, which hinders positioning. 2. Preparing to install the Door Under Garnish RR (1) Part of the double-sided tape liners on the ④ Door Under Garnish RR LH is peeled off and fixed with masking tape. ( ▼ 6 places ) ④ Door Under Garnish RR LH 【Back side】 【Surface side】Masking tape ( ▼ 6 places ) ※ This manual shows the LH side. Do the same for the RH side. 【Part A details】 Masking tape ④ Door Under Garnish RR LH 【Part B details】 Match the shape of the broken line to a certain gap. Front door Rear door ④ Door Under Garnish RR LH D D 【Cross section D-D】 Rear door ⑤ Cross section gauge Door shaped R-end Align the cross section gauge with the rear door. Press the Door Under Garnish to determine the position. ※ For work on the RH side, turn the Cross section gauge over and use it. Caution -4- ▼ ▼ ▼ ▼ ▼ ▼ （1） （2） （3） （6） （4） （5） (2) Pull out the double-sided tape liner in the order of to referring to the figure on the left, and crimp it. (1) (6) 4. Preparing to install the Door Under Garnish FR ！ To crimp the double-sided tape, press it with a force of 49N(5kgf) for about 10 seconds. (2) Part of the double-sided tape liners on the ③ Door Under Garnish FR LH is peeled off and fixed with masking tape. ( ▼ 6 places ) 【Back side】 ( ▼ 6 places ) 【Surface side】 Masking tape ③ Door Under Garnish FR LH ④ Door Under Garnish RR LH Front door Masking tape Rear door ④ Door Under Garnish RR LH ！ Please follow the order of removing the release paper. The position may shift during installation. (1) Apply masking tape to the top of the ④ Door Under Garnish and cut at the split position of the door. ！ Apply masking tape straight. Cut Caution Caution Caution -5- This is the end of the work. （1） （3）（2） （6） （4） （5） Ｅ Ｆ Make sure the clips are attached, the adhesion of the double-sided tape, and make sure that there is no rattling. Make sure there are no scratches or stains. There shall be no significant gaps or separation. ！ Inspection procedure ！ To crimp the double-sided tape, press it with a force of 49N(5kgf) for about 10 seconds. ！ 5. Install the Door Under Garnish FR (1) Open the front door and temporarily fix the ③ Door Under Garnish FR LH with masking tape according to the front door shape, referring to the figure on the left. 【Details of the rear end of the front door】 Please follow the order of removing the release paper. The position may shift during installation. (2) Pull out the double-sided tape liner in the order of to referring to the figure on the left, and crimp it. (1) (6) 【Part E details】【Part F details】 Match the shape of the broken line to a certain gap. Masking tape Masking tape ③ Door Under Garnish FR LH ③ Door Under Garnish FR LH Align the top edge with the masking tape. 10mm Front door Rear door ③ Door Under Garnish FR LH G G 【Cross section G-G】 ⑤ Cross section gauge Door shaped R-end Align the cross section gauge with the front door. Press the Door Under Garnish to determine the position. ※ For work on the RH side, turn the Cross section gauge over and use it. Push ＦＲ ＲＲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ Front door △ Initial release Revision History Description Date 00 2022/08/01 Caution Caution
**************************************************************************************************************
**************************************************************************************************************
SEOCONTENT-END
This product presentation was made with AAWP plugin.