Accessory Installation Guide
| 2025MY Forester – LED Door Projector Light | H4610SL100 |
DOOR PROJECTOR LIGHT
FORESTER 2025MY ～
Installation Manual
PART NO．H4610SL100
For installers
Important
・ We recommend that this product should be installed by a Subaru
dealer. Damage and injury resulting from improper assembly will not be warranted.
・ When installing or removing vehicle parts, pay careful attention not to damage the parts.
・ Ensure that the harnesses are wired safely and properly so that a short circuit does not occur, for example, due to a contact with a sharp edge of a body panel.
・ For details on how to remove and install vehicle parts, refer to the service manual.
Warning・・・Be sure to observe the following for safety. Failure to observe these instructions could lead to danger to life or serious damage.
・ Perform this work in a suffi ciently spacious and fl at space while paying attention to safety. Also, perform this work with the shift knob in neutral or parking, the parking brake set, the engine stopped, and the key removed.
・ Avoid performing this work in an area exposed to rain, etc. Working with wet hands is very dangerous, as doing so could lead to an electric shock. Also, provide adequate ventilation and pay adequate attention to prevent accumulation of exhaust gas etc.
Caution・・・When using or installing this product, be sure to observe the following. Failure to observe these instructions could lead to product performance deterioration or property damage.
・ Before starting the work, be sure to disconnect the negative (-) battery terminals.
・ When disconnecting and connecting the connector, hold the connector and ensure to do so securely.
If the connector is not connected securely, the light may not come on.
・ When connecting the connector, secure the connector fi rmly by inserting it all the way.
・ Do not pull the harness with excessive force. Doing so may cause the terminal to come off , resulting in a contact failure. Also, wire the harness so that it is not caught in the moving part.
・ When removing or restoring the vehicle parts to their original states, follow the service manual.
・ When removing dirt on the product, wipe it off with sponge or other cloth dampened with neutral detergent.
Never use an organic solvent, such as thinner, or acid or alkaline cleaner.
H4610SL100
- 【Compatible Vehicles】Plug-and-play installation suitable for 2013-2017 Crosstrek ;2013-2025 Forester; 2012-2025 Outback;2022-2026 BRZ;2019-2022 Ascent; 2010-2021 Legacy.
- 【Bright & Clear Welcome Projection】 Built with a high-definition projection lens, these LED door welcome lights create a bright, sharp, and eye-catching pattern on the ground when the door is opened. A great upgrade for improving your vehicle’s appearance, adding a premium custom look, and making entry or exit more stylish at night.
- 【Long-Lasting Pattern, No Fading】 The projector light uses a durable optical structure and heat-resistant lens design to help keep the projected image clear and vivid over time. The pattern is made for stable light output and long service life, helping avoid dark, blurry, or faded projection after extended use.
- 【Plug & Play, No Batteries Needed】 No battery, no drilling, and no complicated wiring required. Simply remove the original door light, connect the factory-style plug, and snap the new projector light into place. The installation can usually be completed in about 3 minutes, making it an easy car lighting upgrade.
- 【 2-Year Support】 Package includes 2 pieces of Nammero door projector courtesy lights for left and right doors. Ideal for car styling, interior/exterior lighting upgrades, and personalized auto accessories. We provide 2-year after-sales support; please contact us if you have any installation or quality problems.
- 【Compatible for】Forester Fourth generation 2013-2017 SJ,Forester Fifth generation 2018-PRESENT SK
- 【Super cool 】When the door is opened, the Forester LOGO is illuminated onto the open door surface to provide a light to aid entry into and out of the vehicle.
- 【Easy to install】 Direct Replacement. No modifications required. No wire cutting. Please kindly confirm your original car door light can be powered before purchasing.
- 【Product Features】 High-brightness led door projection lamp, to show your car a bright, clear and color-fast logo projection
- 【After sale】 If there are any problems with our products, just feel free to contact us.
- Unique patterns: Personalized patterns add a unique charm to your car. Increase driving fun and create a stylish atmosphere. Best to surprise your family and friends.
- Customized Design: LED car door lights projector compatible with Forester 2013-present,Outback 2009-present, Ascent 2019-2022, Legacy 2010-2021 accessories. (Tip: Make sure your car has door lights before buying, and the lights will light up.)
- Material Description: The door lamp adopts a sturdy ABS flame retardant shell to prevent high temperature. The light is turned off regularly, which is safe and saves electricity.
- Easy Installation: Install in 4 steps. 1. Use a flat-blade screwdriver to pry off the original lamp; 2. Unplug the socket of the original lamp; 3. Insert our puddle lamp; 4. Put it back into the opening so that it is OK.
- Service Guarantee: Package includes: 2Pcs LED car door light, 1 Crowbar. If you have any questions, you can leave us a message. We'll get back to you in 24hours. We are happy to solve the problem for you!
- 【Compatibility】1.Forester Fourth generation 2013-2017 SJ Fifth generation 2018-PRESENT SK 2.Outback, 4th Gen/5th Gen 6th Gen 2009-2014 BR/BM, 2014-2019 BS, 2020-present BT 3.Ascent 2019-2022
- 2.【High Quality】Featuring high definition projection with a premium lens, these puddle lights offer a longer lifespan, brighter output, and lower power consumption. The high-brightness LED door projection lamp creates a bright and clear logo projection, making your car stand out.
- 【Easy to install】No modifications or wire cutting are required for installation. These car door logo lights are a direct replacement and require the car to have original door lights for compatibility.
- 【Super cool】When the door is opened, the logo is illuminated onto the open door surface for a super cool effect, making it a perfect choice for car enthusiasts who want to add a unique touch to their vehicle.
- 【After sale】We offer full after-sale support. If there are any problems with our products, please feel free to contact us.
- 【Compatible for】1.Forester Fourth generation 2013-2017 SJ Fifth generation 2018-PRESENT SK 2.Outback, 4th Gen/5th Gen 6th Gen 2009-2014 BR/BM, 2014-2019 BS, 2020-present BT
- 【Super cool 】When the door is opened, the Wilderness LOGO is illuminated onto the open door surface to provide a light to aid entry into and out of the vehicle.
- 【Easy to install】 Direct Replacement. No modifications required. No wire cutting. Please kindly confirm your original car door light can be powered before purchasing.
- 【Never fade 】Never fade high brightness Wilderness logo slides 2pcs set car door ghost shadow projector logo light ,High-brightness led door projection lamp, to show your car a bright, clear and color-fast logo projection
- 【After sale】 If there are any problems with our products, just feel free to contact us.
SEOCONTENT-START
-1-
PART NO．H4610SL100
DOOR PROJECTOR LIGHT
PKI-0095-2
△ 00
Warning・・・Be sure to observe the following for safety. Failure to observe these instructions could lead to danger to life or serious damage.
・ Perform this work in a suffi ciently spacious and fl at space while paying attention to safety. Also, perform this
work with the shift knob in neutral or parking, the parking brake set, the engine stopped, and the key removed.
・ Avoid performing this work in an area exposed to rain, etc. Working with wet hands is very dangerous, as doing
so could lead to an electric shock. Also, provide adequate ventilation and pay adequate attention to prevent
accumulation of exhaust gas etc.
For installers
Important
・ We recommend that this product should be installed by a Subaru dealer. Damage and injury resulting from
improper assembly will not be warranted.
・ When installing or removing vehicle parts, pay careful attention not to damage the parts.
・ Ensure that the harnesses are wired safely and properly so that a short circuit does not occur, for example, due
to a contact with a sharp edge of a body panel.
・ For details on how to remove and install vehicle parts, refer to the service manual.
Caution・・・When using or installing this product, be sure to observe the following. Failure to observe these instructions could lead to
product performance deterioration or property damage.
・ Before starting the work, be sure to disconnect the negative (-) battery terminals.
・ When disconnecting and connecting the connector, hold the connector and ensure to do so securely.
If the connector is not connected securely, the light may not come on.
・ When connecting the connector, secure the connector fi rmly by inserting it all the way.
・ Do not pull the harness with excessive force. Doing so may cause the terminal to come off , resulting in a
contact failure. Also, wire the harness so that it is not caught in the moving part.
・ When removing or restoring the vehicle parts to their original states, follow the service manual.
・ When removing dirt on the product, wipe it off with sponge or other cloth dampened with neutral detergent.
Never use an organic solvent, such as thinner, or acid or alkaline cleaner.
Installation Manual
FORESTER 2025MY ～
-2-
○○○○ R
A14930-2000
○○○○ L
A14930-1000
NO.
①
②
Part name
DOOR PROJECTOR LIGHT L
DOOR PROJECTOR LIGHT R
Quantity
1
１
① ②
● Waste cloth ● fl at head screwdriver
Completion drawing
Components
DOOR PROJECTOR LIGHT
“L” mark indicated
on the backside
“R” mark indicated
on the backside
Tools
-3-
Confi rm L/R side is correct. Connect the
DOOR PROJECTOR LIGHT to the courtesy
lamp connector.
● L side：DOOR PROJECTOR LIGHT L
● R side：DOOR PROJECTOR LIGHT R
1
3
2
Courtesy lamp
Flat head screwdriver
Courtesy lamp
connector
DOOR PROJECTOR LIGHT L
L side door
L side door
Front of the
car body
Installation procedure
（1）Turn off the ignition switch.
（2）Disconnect the negative (-) battery terminal.
（1）Apply a waste cloth on a fl at head
screwdriver. Remove the courtesy lamp
by inserting the fl at head screwdriver into
the vehicle’s front side of the courtesy
lamp.
（2）Remove the connector from the courtesy
lamp.
When removing the vehicle parts, follow the
service manual and be careful not to scratch
or damage them.
-4-
4
5
6
7
Insert
②
①
Tab
Connect the negative (-) battery terminal.
Open the door and confi rm the DOOR
PROJECTOR LIGHT’s image is correctly
projected.
Confi rm the DOOR PROJECTOR LIGHT unit is securely fi xed to the door trim.
Open/close the door and check the DOOR PROJECTOR LIGHT unit does not contact
with the door-sill, does not move, or fall off .
L side R side
Door trim
DOOR PROJECTOR
LIGHT
Front of the
car body
Insert the DOOR PROJECTOR LIGHT into
the door trim. Ensure the front side tab is
locked at the correct position.
Repeat Steps 2 － 4 for the R Side Door.
-5-
△ Description Date
Revision History
△ 00 ・Initial release August 31, 2023
**************************************************************************************************************
**************************************************************************************************************
SEOCONTENT-END
This product presentation was made with AAWP plugin.