Accessory Installation Guide
| 2025MY Forester Utility Hook Manual Rear Gate | F5510SL060 |
UTILITY HOOK MANUAL RR GATE KIT
Installation Manual
Genuine part number F5510SL060
Applicable car model FORESTER 2025MY ～
Installation Instructions
１．Remove the Trim caps of the rear gate with a flat blade screwdriver.
Caution
The removed trim caps will not be re-used. Place trim caps in glove box.
２．Fit the washer to the turn nut, and slightly insert it into the screw of the Utility hook.
３．Insert the Utility Hook to the rear gate and turn it clockwise by hand.
Caution
When fastening the Utility Hook, install it securely until it touches the vehicle trim and the hook does not rattle and turn.
Tip
Make sure that the screws are tightened before installing the hooks. If the hook spins freely, use a flathead screwdriver to correct the direction of the turn nut (1) and check it that the screws are tightened again (2). Turn nut will be pulled to downward by screwed bolt (3) if its position is correct.
４．Tie on the caution label to the installed utility hook.
Post-Installation Check
Check the followings;
・Make sure that there is no rattling or looseness of each Utility Hooks.
・Make sure that the Caution label is tied on to the Utility Hook.
5. Rear Gate Stopper Installation
Note
Please put the stopper in the Under-floor storage after installation check.
This stopper is only for RH side when rear gate is opening. It cannot be installed on the LH side or when rear gate closing.
（1）Hold the bottom end of the stopper with your right hand and hold it near the Bracket B.
Tip
Please make sure that do not scratch to vehicle body by the end of the stopper when installing.
（2）Run the band of upper side through the Bracket A as shown in the figure.
Then insert the tip of the holder into the gap between the Bracket A and rear gate panel.
（3）Properly fit a groove of the bottom end of the stopper to the Bracket B. There is a gently match point of the groove and the bracket edge.
（4）Fasten the button of the band of upper side.
Then wrap the band of the bottom side around the damper and fasten the button.
Caution
Please make sure that the button is fastened properly before use the hooks. There is a risk of breakdown or injury.
（5）Please do it in reverse order when remove the stopper.
F5510SL060
- Rear Trunk Cargo Hook Set
- Genuine Subaru
Part Number: F5510SL010 - Forester 2025 2026
- Outback 2026
- Positioned on the left and right sides of the cargo area to hang personal items and gear.
- Replacement Models: Our cargo area utility hooks fit for Subaru Forester 2025-2026/ Outback 2026, replace F5510SL010
- Core Function: Our trunk hooks utilize the unused vertical space in the trunk to secure and hang items, preventing them from swaying, tipping over, or scattering while driving. This also improves the trunk's space utilization
- Weight Capacity Notes: Our trunk hooks have a maximum weight limit of 6.6 pounds. Hanging excessively heavy items may cause the hooks to break or damage the headrest metal rod. Please do not hang too many or too heavy items
- High-Quality Materials: Our trunk hooks are made of high-quality ABS plastic and metal, featuring a sturdy structure, wear resistance, high temperature resistance, and resistance to deformation and aging. They are suitable for hanging medium-weight items for daily travel
- Easy Installation: Simply insert the hook into the pre-drilled circular hole on the side wall of the trunk and rotate to secure it. No tools are required for removal, making them suitable for frequent daily use or temporary storage needs
- Genuine Subaru Impreza Rear Trunk Cargo Hook
- Trunk Hook F551SFL100
- price is for 1 if you need 2 please order 2
- Conveniently helps to hold shopping bags upright. The hook folds out of the way when not in use. Each kit includes one hook.
- 2017-2023 Impreza Sedan
- 【Compatible With】This Cargo Area Utility Hooks fit for Subaru Forester 2025 2026 Outback 2026.
- 【Replace Part Number】F5510SL010 Please confirm whether your model is suitable before placing an order.
- 【Premium Quality】It is made of high-quality materials and is sturdy and durable, with a long service life. It will not deform even when carrying heavy loads for a long time.
- 【Save space】This car hook set helps organize items like bags and tools, preventing sliding and saving space. Ideal for commuting, shopping, or travel. Each set includes two hooks that can be mounted vertically to secure cargo nets or tool holders. The multi-angle snap ring allows easy hanging of gear such as backpacks or boots—practical and flexible.
- 【Service】If you have any questions,you can contact us at any time.Your satisfaction is our ultimate goal.
- OEM Part Number: F5510SL010.
- Compatibility With: Compatible with Subaru Forester 2025 2026, for Subaru Outback 2026.
- Features: Designed specifically for the 2025 Subaru Forester; Direct fit replacement for OEM Part **F5510SL010**; Helps organize cargo area and prevent items from shifting; Made from strong, durable 3D-printed material; Simple, tool-free installation.
- Package Included: Utility Hook 2 pack - F5510SL010.
- Notice: Please confirm the part number, fitment details and pictures listed are the same as your needs before purchasing.
SEOCONTENT-START
Installation Manual
△00
1
UTILITY HOOK MANUAL RR GATE KIT
Genuine part number
Applicable car model
F5510SL060
FORESTER 2025MY ～
Utility Hooks
Rear Gate Stopper
Rear Gate Stopper is for hanging stuff on the Utility Hooks when rear gate opening. Please put it in the Under-floor storage after installation check.
Note
Kit includes
No. Components Qty.
1 Utility Hooks 2 2 Turn Nuts
3 Washers
Caution Labels 2
2
1
※Instruction manuals are included in each one.
Marks
Part Number F5510SL050×1
※Instruction
manuals
5 Rear Gate Stopper
1 Part Number J2010SL200×1 ① ② ③ ④ ⑤ Installation Instructions １．Remove the Trim caps of the rear gate with a flat blade screwdriver.
Caution
The removed trim caps will not be re-used. Place trim caps in glove box. ２．Fit the washer to the turn nut, and slightly insert it into the screw of the Utility hook. ３．Insert the Utility Hook to the rear gate and turn it clockwise by hand.
Caution
When fastening the Utility Hook, install it securely until it touches the vehicle trim and the hook does not rattle and turn. Washer Turn Nut Trim Caps
Stop inserting when lightly touch to the bolt. Do not fully insert. Tip
Make sure that the screws are tightened before installing the hooks. If the hook spins freely, use a flathead screwdriver to correct the direction of the turn nut (1) and check it that the screws are tightened again (2). Turn nut will be pulled to downward by screwed bolt (3) if its position is correct. Utility Hook Utility Hook (1) Turn Nut (2) Hook (3) Flathead screwdriver ４．Tie on the caution label to the installed utility hook.
Tip
[Reference] How to tie on the caution label.
Utility Hook Caution Label Post-Installation Check
Check the followings;
・Make sure that there is no rattling or looseness of each Utility Hooks.
・Make sure that the Caution label is tied on to the Utility Hook. 2 Then wrap the band of the bottom side around
the damper and fasten the button.
3
Content
Revised Content
Date Δ00 Δ01 Δ02 Created New 2023.10.06
（1）
（2）
f upper side.
Please make sure that do not scratch to vehicle body by the end of the stopper
when installing.
end of the
stopper to the Bracket B. There is a gently match point of the groove and the bracket edge.
（3） right hand and hold it near the Bracket B. A as shown in the figure.
h the Bracket
（4）
Then insert the tip of the holder into the gap
between the Bracket A and rear gate panel.
Bottom end of
the stopper
BRKT B
Damper
Tip of the Stopper
Band
BRKT A
BRKT A RH
Bottom end
BRKT B
Button
Tip of the stopper
Band
Button
Holder body Damper
Band
5. Rear Gate Stopper Installation
Tip
Bracket A Bracket B
Tip of the
Stopper
Upper side
Upper side
Bottom side
Bottom side
Please make sure that the button is fastened properly before use the hooks. There is a risk of breakdown or injury.
Caution remove the stopper.
（5）
Please put the stopper in the Under-floor storage after installation check.
This stopper is only for RH side when rear gate is opening. It cannot be installed on the LH side or when rear gate closing.
Note
**************************************************************************************************************
**************************************************************************************************************
SEOCONTENT-END
This product presentation was made with AAWP plugin.