| “This site contains affiliate links for which OEMDTC may be compensated” |
Accessory Installation Guide
| 2024MY+ WRX (all trims) – Auto-Dimming Mirror with Compass and HomeLink | H501SVC000 |
Installation instructions
Instructions d’installatiion
Part number: H501SVC000
Numéro de piéce:
Vehicle: WRX
Véhicule:
1
Disconnect battery. If equipped disconnect eyelet cable only.
Déconnectez la batterie. Si elle en est équipée, déconnectez le câble de l’oeillet uniquement.
2
Remove original mirror by pulling on tab away from windshield and sliding mirror up and off the windshield mirror mount.
Retirez le rétroviseur d’origine en tirant sur la languette pour l’éloigner du pare-brise et en faisant glisser le rétroviseur vers le haut pour le sortir du support
3
1 – Remove cover with trim tool starting from the front.
1 – Retirez le couvercle à l’aide de l’outil pour garniture en commençant par l’avant.
4
1 – Remove two screws.
1 – Retirer les deux vis.
5
Gently pull down cover to release clips.
Tirez doucement le couvercle vers le bas pour libérer les attaches.
6
Disconnect harnesses from maplight/cover assembly.
Débrancher faisceaux de la lampe de lecture ou du couvercle.
7
Install auto-dimming mirror by sliding mirror down onto the base. Tighten set screw with T-20 Torx bit to 13.3 – 17.7 in-lbs.
Installer le rétroviseur intérieur à atténuation automatique en le faisant glisser vers le bas sur la base. Serrer la vis de pression avec un embout Torx T-20 à 13,3 à 17,7 po-lb
8
Route wire harness through Eyesight cover opening.
Faire passer le faisceau de câblage à travers l’ouverture du couvercle Eyesight.
9
Route harness between sheet metal and plastic headliner/bracket.
Faites passer le harnais entre la tôle en métal et le revêtement de toit/le support en plastique.
10
Connect mirror harness to pre-arranged vehicle harness.
Brancher le faisceau du rétroviseur au faisceau du véhicule préinstallé.
11
Install mirror harness cover.
Poser le couvercle du faisceau de rétroviseur.
12
Secure wire harness with wire tie.
Fixer le faisceau de câblage avec une attache autobloquante.
13
Reinstall map light/cover assembly.
Réinstaller la lampe de lecture ou le couvercle.
14
Reconnect battery. If equipped reconnect eyelet cable. Tighten bolt to 66 in-lbs.
Rebranchez la batterie. Si elle en est équipée, rebranchez le câble de l’oeillet. Serrez les boulons à 66 po-lb.
15
Using dark cloth or cardboard, completely cover forward-looking sensor.
Avec un linge sombre ou un carton, couvrez complètement le capteur pointé vers l’avant.
16
To calibrate compass reference mirror user guide.
Pour étalonne la boussole, reportez-vous au manuel du rétroviseur.
https://techinfo.subaru.com/stis/doc/accInstallGuide/H501SVC000_WRX_MY2024_IxI_2-6-24.pdf
Loading...
Reload document 
Open in new tab
- Car Auto Dimming Rear View Mirror, Germid auto-dimming rearview mirror utilizes 3rd generation electrochromic material and dual photoelectric sensors to automatically adjust the dimming level and eliminate glare, giving you a safer and more comfortable driving experience.
- Original Factory Style & Universal Fitness, With its sleek and modern design, our mirror complements your vehicle's original factory style. Its replaceable rearview mirror bracket with double-jointed ball provides adjustable visibility and universal fit for most car models.
- High Quality Material-4.0 mm Thickness Glass, Germid mirror is made with factory OEM quality 4.0 mm glass, which meets vehicle safety standards and offers high reflectance for a clear and crisp image.
- Easy for Installation, Included with the mirror is a Door Clip Panel Trim Removal Tool, making it easy to hide the wire during installation. Moreover, our patent replaceable rearview mirror bracket allows for easy installation and replacement.
- These mirrors eliminate the glare of headlights behind you for safer nighttime
- Mirror automatically dims as it detects glare
- The brighter the glare, the more the mirror dims
- Dimensions - 12 x 6.5 x 4.75 in.
- Gentex Auto-Dimming Rear View Mirrors
- 👍【Latest Upgrade】- Upgraded uniform and glare-free LED light bars more natural and soft, bright but not dazzling, protecting your eyes.The light is even on your face,so you can see more realistically how your makeup looks. No more makeup disaster!
- 🪞【Dimmable Bicolor Led Lights】- The led car mirror has 64 white lights and 16 yellow lights , which is 50% brighter and use 60% less energy than normal bulbs. Short press the two sensor switches to switch between three light colors: white, yellow, white and yellow. Long press for dimming according to what you need. 2500-6500K color temperature is equivalent to outdoor sunlight, so your makeup will look naturally flawless.
- 👆【Touch-Sensitive Control】- The car vanity mirror has highly sensitive touch control, simply touch one of the touch switches to turn it on and off. You can switch between two colors of lights (cool white,warm yellow).Long press to adjust the brightness of the lights. The mirror also has a memory function that remembers brightness and color when you last settings.
- 🔋【Rechargeable Lithium Battery】- Built-in 2000mAh lithium battery, which can be charged through the socket, computer, mobile power.2 interface design, Comes with 10ft USB cable, long enough, free to use the car visor mirror at anywhere and anytime. It can last 8 hours if 100% brightness while always on mode.
- ❤️【Universal Size Design】- The size of car makeup mirror is 10.2(L)*5.2(W)*0.4(H) inches, which suits for most of the sun visor of cars. Ultra-thin,making it easy to install and use without taking up extra space in your car. With adjustable lanyard, easy to install and use.Vanmirr is responsible for every customer, You will get MORE RESULTS than you expect when you contact us if you are disappointed with our car light mirror.
- Auto-Dimming
- Homelink integration
- Frameless Auto Dimming Mirror
- Wiring harness is included.
- Wire cover included
- International products have separate terms, are sold from abroad and may differ from local products, including fit, age ratings, and language of product, labeling or instructions.
- 【BUY NOTE】Check the vehicles modle and year to confirm the compatibility before purchase.
- 【Compatible With Toyota】Automatic Dimming Rearview mirror compatible with Toyota 2007-2012 Camry, 2007-2012 Solara, 2009-2013 Matrix, Corolla, 2010-2013 Prius, 2010-2012 4Runner
- 【Excellent Qualtiy Interior Mirrors】OEM Factory Production, High Quality Rear View Mirror, is constructed of premium material for long lasting durability and reliability
- 【Compatible With Lexus】Automatic Dim Interior Rear view mirror Compatible With Lexux Vehicles 2007-2012 ES350, 2006-2008 IS250, IS350, 2006-2010 GS300 GS350 GS430, 2007-2009 LS460
- 【OEM Factory Qualtiy】This automotive rear view mirror is an excellent safety feature that can help drivers better see rear of vehicle and reduce the danger posed by blind spots.
- ??High Quality Material??100% high quality material.The Car Rearview Mirror made of high quality and material.Good quality not only can provide a safer guarantee for your life,but also good materials can increase product life.
- ??After-sales Guarantee??If you have any questions about the product,or you encounter problems with your use,you can contact us directly.We will provide you with a solution in good time.No need worry about after-sale services.
- ??High Quality Material??100% high quality material.The Car Rearview Mirror made of high quality and material.Good quality not only can provide a safer guarantee for your life,but also good materials can increase product life.
- ??High Quality Material??100% high quality material.The Car Rearview Mirror made of high quality and material.Good quality not only can provide a safer guarantee for your life,but also good materials can increase product life.
- ??High Quality Material??100% high quality material.The Car Rearview Mirror made of high quality and material.Good quality not only can provide a safer guarantee for your life,but also good materials can increase product life.
- Automotive auto dimming rearview mirror
Last update on 2024-06-17 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.
SEOCONTENT-START
Installation instructions
Instructions d’installatiion
Auto dimming mirror
Tetroviseur antieblouissement
Tools required
Outils requis
Part number:
Numéro de piéce:
Kit contents Contenu de la trousse
H501SVC000
Description: Auto dimming mirror
Description: Tetroviseur antieblouissement
ISSUE
B
PAGE
1/5
DATE
2/6/2024 SUBARU OF AMERICA
A
T-20
Panel removal tool
Outil de dépose du panneau
Vehicle: WRX
Véhicule:
10 mm
12 mm
8 mm
B C D
Wire harness cover
Couvre-faisceau de câblage Wire Tie
Attache autobloquante
Foam Tape
Ruban mousse
PART NUMBER
H501SVC000
Wire Snips
ISSUE
B SUBARU OF AMERICA PART NUMBER
H501SVC000
DATE
2/6/2024
1
Disconnect battery. If equipped disconnect eyelet cable only.
Déconnectez la batterie. Si elle en est équipée, déconnectez
le câble de l’oeillet uniquement.
PAGE
2/5
10 mm
12 mm
3
1 – Remove cover with trim tool starting from the front.
1 – Retirez le couvercle à l’aide de l’outil pour garniture en
commençant par l’avant.
2
Remove original mirror by pulling on tab away from windshield
and sliding mirror up and off the windshield mirror mount.
Retirez le rétroviseur d’origine en tirant sur la languette pour
l’éloigner du pare-brise et en faisant glisser le rétroviseur vers
le haut pour le sortir du support
4
1 – Remove two screws.
1 – Retirer les deux vis.
ISSUE
B SUBARU OF AMERICA PART NUMBER
H501SVC000
DATE
2/6/2024
PAGE
3/5
5
Gently pull down cover to release clips.
Tirez doucement le couvercle vers le bas pour libérer les attaches.
6
Disconnect harnesses from maplight/cover assembly.
Débrancher faisceaux de la lampe de lecture ou du couvercle.
7
Install auto-dimming mirror by sliding mirror down onto the
base. Tighten set screw with T-20 Torx bit to 13.3 – 17.7 in-lbs.
Installer le rétroviseur intérieur à atténuation automatique en
le faisant glisser vers le bas sur la base. Serrer la vis de pression
avec un embout Torx T-20 à 13,3 à 17,7 po-lb
8
Route wire harness through Eyesight cover opening.
Faire passer le faisceau de câblage à travers l’ouverture du
couvercle Eyesight.
ISSUE
B SUBARU OF AMERICA PART NUMBER
H501SVC000
DATE
2/6/2024
PAGE
4/5
9
Route harness between sheet metal and plastic headliner/
bracket.
Faites passer le harnais entre la tôle en métal et le revêtement
de toit/le support en plastique.
10
Connect mirror harness to pre-arranged vehicle harness.
Brancher le faisceau du rétroviseur au faisceau du véhicule
préinstallé.
11 12
Install mirror harness cover.
Poser le couvercle du faisceau de rétroviseur.
Secure wire harness with wire tie.
Fixer le faisceau de câblage avec une attache autobloquante.
ISSUE
B SUBARU OF AMERICA PART NUMBER
H501SVC000
DATE
2/6/2024
PAGE
5/5
13
Reinstall map light/cover assembly.
Réinstaller la lampe de lecture ou le couvercle.
14
Reconnect battery. If equipped reconnect eyelet cable. Tighten
bolt to 66 in-lbs.
Rebranchez la batterie. Si elle en est équipée, rebranchez le
câble de l’oeillet. Serrez les boulons à 66 po-lb.
10 mm
12 mm
15
16
Using dark cloth or cardboard, completely
cover forward-looking sensor.
Avec un linge sombre ou un carton, couvrez
complètement le capteur pointé vers
l’avant.
To calibrate compass reference mirror user guide.
Pour étalonne la boussole, reportez-vous au manuel du rétroviseur.
**************************************************************************************************************
**************************************************************************************************************
SEOCONTENT-END
