“This site contains affiliate links for which OEMDTC may be compensated” |
Owner Manual
2020MY Outback Owner’s Manual
MSA5M2004A
Table of Contents
Introduction | 1 | |
Illustrated Index | 13 | |
Seat, Seatbelt and SRS Airbags | 27 | Chapter 1 |
Keys and Doors | 111 | Chapter 2 |
Instruments and Controls | 163 | Chapter 3 |
Climate Control | 271 | Chapter 4 |
Audio | 291 | Chapter 5 |
Interior Equipment | 295 | Chapter 6 |
Starting and Operating | 315 | Chapter 7 |
Driving Tips | 409 | Chapter 8 |
In Case of Emergency | 439 | Chapter 9 |
Appearance Care | 463 | Chapter 10 |
Maintenance and Service | 471 | Chapter 11 |
Specifications | 519 | Chapter 12 |
Consumer Information and Reporting Safety Defects | 539 | Chapter 13 |
Index | 555 | Chapter 14 |
MSA5M2004A
https://techinfo.subaru.com/stis/doc/ownerManual/MSA5M2003A-2004A_STIS.pdf
https://static.oemdtc.com/OwnerManual/MSA5M2004A.pdf
- 【Buy with Confidence】 As a America's No.1 diagnostic tool brand, Innova stands for innovation, quality, and accessibility in the automotive diagnostic industry. We are known for developing cutting-edge diagnostic tools that are user-friendly, reliable, and made for US by Americans.
- 【Unleash Your Drive's Potential】Much more than a car code reader, the 6100P scanner effectively reads and erases engine, ABS, SRS, and transmission codes for popular US car makes such as Ford, Chevy, Dodge, GM, etc. When the traction light is constantly on, the ability to really detect where the problem is concerning brakes and airbags enables you to make sure all safety measures in place before putting yourself in harm's way.
- 【Your Car's Health Doctor】Easily view procedures or send commands for oil change, mileage or driving time reset for most 1996 and newer OBD2 vehicles. It also monitors your oil level and oil life status, ensuring optimal vehicle health.
- 【alternator Test】The Innova 6100P scanner is perfect for assessing the performance of the alternator in your hybrid, car, SUV, minivan, or light truck diesel as well. During rough winters and scorching summers, this diagnostic tool will be invaluable when trying to root out start-up issues.
- 【Drive with Confidence and Peace】Quickly identify if your vehicle needs immediate attention with our Code Severity Levels function. This feature helps you understand whether you need to fix an issue immediately or if it can wait until you get home, keeping warning lights at bay.
- 5 IN 1 DIAGNOSTIC SCANNER: This is an OBDII scanner and 4 systems diagnostic tool. The AUTOPHIX 3210 PRO Bluetooth Auto Scanner not only has OBDII diagnostic function, but can also be used as an ABS/SRS/transmission scanner and check engine code reader. When it is an OBD2 scanner, you can use it to check if your car is ready for annual test via I/M preparation menu. In addition, the built-in DTC library, live data stream, data playback, performance testing and many more such functions are supported by it.
- RELIABLE CAR HEALTH MONITOR: Are you confused when the ABS/SRS/Transmission/Check Engine warning light is blinking? The AUTOPHIX 3210 PRO Bluetooth Scanner will help you to do a thorough scanning and inspecting of your car and find out the root cause, which saves your time and money. Tip:The warning light will be turned off after the problem is solved. Airbag crash/collision data cannot be cleared, even if you replace the airbag with a new one.
- QUICK DIAGNOSIS: The 3210 PRO is the newest 2024 Enhanced 4-System Bluetooth Code Reader that retrieves vehicle information, reads/clears trouble codes, and displays a 4-in-1 live data stream. You'll easily find out what's wrong with your car. In just a few minutes, you'll be in control of your car!
- EXCLUSIVE APP: Are you tired of the following with third party apps? For example: 1.need to download different apps for different cars? 2. require extra download fees? 3. only support a few functions? 4. can only use one of Android and iOS? Now!One AUTOPHIX 3210 PRO Scanner is enough to solve all the above problems. The must-have wireless/bluetooth automotive diagnostic tool/code reader for today's car owners. iPhone iOS, iPad, Android can be downloaded for free without any additional subscription fees.
- ADVANCED DATA FLOW DISPLAY:AUTOPHIX 3210 PRO Bluetooth code reader allows you to graphically display your vehicle's data flow instead of boring text, including engine coolant temperature, engine RPM, vehicle speed, absolute throttle position, control module voltage, etc. You can view different parameter values corresponding to different times. The advanced data streams provide useful information for entry-level professionals and diyers who can troubleshoot vehicle problems quickly and efficiently.
- 🎄【Easy to Use--Work out of box】+【FOXWELL 2024 New Version】 FOXWELL NT604 Elite scan tool is the 2024 new version from FOXWELL, which is designed for those car owners who want to figure out the cause issue before fixing the car problem via scanning the most common systems like abs srs engine and transmission.The NT604 Elite diagnostic tool comes with latest software, which can be used out of box. No need to waste time to download the software first.
- 🎅【Affordable】+【Reliable Car Health Monitor】 Will you be confused what happen when the warning light of abs/srs/transmission/check engine flashes? Instead of taking your cars to dealership, this foxwell scanner will help you do a thorough scanning and detection for your cars and pinpoint the root cause. It will t-urn off the warning light car after the problem is fixed.👉TIPS: Airbag crash/collision data can NOT be cleared even you replace the new airbag.
- 🎄【5 in 1 Diagnostic Scanner】Compared with those auto scanners (50-100), NT604 Elite code scanner not only includes their OBDII diagnosis but also it can be an abs/srs scanner, transmission and check engine code reader. When it’s an odb2 scanner, you can use it to check if your car is ready for annual test through I/M readiness menu. In addition, live data stream, built-in DTC library, data play back and print, all these features are a big plus for it.
- 🎅【Fantastic AUTOVIN】+【No extra software fee】Through the AUTOVIN menu, this NT604 Elite car scanner allows you to get your V-IN and vehicle info rapidly, no need to take time to find your V-IN and input one by one. What's more, the NT604 Elite abs srs scanner supports 60+ car makes from worldwide (America/Asia/Europe). You don’t need to pay extra software fee.
- 🎄【Solid protective case KO plastic carrying bag】+ 【Lifetime update】Almost all same price-level obd scanner diagnostic tool only offers plastic bag to hold on the scanner.However, NT604 Elite automotive scanner is equipped with solid protective case, preventing your obd2 scanner from damage. Then you don’t need to pay extra money to buy a solid toolbox.
- 2024 Best Choice for ABS Bleeder Scan Tool - Was the brake pedal always slowly sinking down or becoming loose? This abs brake bleeding scan tool will bleed the brake system by cycling the pump and valves to achieve a tight brake pedal. It's the most affordable obd2 scanner with abs auto bleed function you can find. With the clear step by step instruction, even a beginner can use it. Coverage check on FOXWELL official site: Support- Diagnostic Coverage List.
- More Than a Entry Level OBD Scanner, Ideal for Home Mechanics - Based on the NT301 FOXWELL Scanner, NT630 Plus takes OBD diagnostics to the next level by customizing all functions for ABS and SRS systems. This srs abs scanner provides in-depth insights on error code diagnosis, wheel speed sensor live data, airbag circuits and cable connectors monitor, module activation and etc. It's an total game-changer in resolving ABS SRS issues.
- No More Higher End Service than You Needed - One NT630 Plus is enough! This obd2 scanner with abs and srs takes depth diagnosis on Anti-Lock Brake System & Supplemental Restraint System, and also performs daily required resetting services which same priced scanners cannot do. Like Airbag light reset/ SAS(Steering Angle Sensor) adjustment/ Oil light reset and EPB service functions. this car scanner will help the part to operate normally after the faults repaired.
- Also can Work like NT301 - The NT630 Plus abs code reader connect to the OBD2 port directly. It will diagnose all obd2 modules instantly, displays the live data, locates bad sensors and I/M readiness status before the annual inspection. Guides you to do the maintenance work, reduces the potential driving risk and keep a peak performance on the road.
- Complicate? Unreadable? - Intuitive LCD display with clear operate instructions, even a beginner can diagnose the car faults with the NT630 Plus. Ergonomic Touch with anti-collision and anti-slip cover design, comfortable for daily car diagnose work. Unique button press sound will provide the overall tactile and visual experience to notice you a task has been completed or a command has been executed.
- 🎁 New Elite Version🎁 Easy to Use--Work out of Box🎁Function as LAUNCH CRP123E 🎁 Lifetime Update🎁 5 YEARS Back Up.
- [Engine/ABS/SRS/Transmission Diagnostic Tool]----The crp123 obd2 scanner is perfect balance of power and affordability, providing the ability to view preset, or user defined, live data streams for ENGINE, AT, ABS and SRS data, the ability to graph, record, replay and print data, read and resets codes for engine/abs/srs/transmission system.(Note: Does not work for other System and does not have Special services!)
- [Full OBDII Test Code Reader]----LAUNCH CRP123 scan tool supports all 10 modes of OBDII standard to ensure complete, accurate, system diagnosis. Read and Clear DTCs, do smog tests , I/M readiness and O2 sensor tests, Mode 06 EVAP system test, Mode 08 on-board test component test. And OBDII Code lookup tool and acronym database to assist and speed diagnosis and repair time.
- [Live Data Stream + Advanced OBDII Scanner + Lifetime Update]---- Launch crp123 scanner support for Generic OBDII Codes (P0, P2, P3 and U0); manufacturer specific codes (P1, P3 and U1); pending codes; freeze frame data; monitor and I/M readiness; live PCM stream data; graphing functionality for up to four (4) live data streams include the Engine Coolant Temperature, Long&Short Fuel Trim, the change of Accelerator Pedal Position Sensor , Throttle valve position , Generator load signal,Fuel Tank Pressure , Engine RPM, Intake Ait Temperature and so on; clears DTC codes and turns off the MIL; resets monitors; provides Data Link Connector (DLC) location hints.
- [Extensive Vehicle Coverage + 10 Languages]--The LAUNCH CRP123 reads data from ENGINE, TRANSMISSION, ABS and SRS systems from Asian, US and European manufacturers. Coverage includes for Suzuki, for Honda, for Mitsubishi, for Nissan, for Toyota,for Mazda, for Hyundai,for Kia, for Subaru,for Infiniti, for Lexus, for Acura, for Isuzu, for Ford, for GM, for Chrysler, for Benz, for BMW, for VW, for Opel, for Volvo, for Fiat,for Land Rover, for Seat, for Skoda, for Audi,for Porsche, for Saab, for Jaguar and many others. Support 10 different languages.
- SIMPLIFYING CAR REPAIR - Our goal is to simplify your car repair process. Our device turns your smartphone into a powerful OBD2 scanner diagnostic tool, allowing you to quickly understand your vehicle's problem, view recommended fixes, and purchase the necessary parts for repair.
- EXPERIENCE PROFESSIONAL DIAGNOSTICS - BLCKTEC's enhanced vehicle diagnostics gives you access to advanced features typically found only on high-end scanners. With our car code reader you can read and clear engine codes, ABS (brakes), SRS (airbags), TPMS codes, and many more.
- RELIABLE AND ACCURATE RESULTS - Our car scanner utilizes the latest OBD2 technology to provide accurate and reliable diagnostic information, ensuring that you can trust the results you receive.
- COMPATIBLE WITH A WIDE RANGE OF VEHICLES - Our bluetooth OBD2 scanner works with most vehicles made after 1996, including cars, trucks, and SUVs, making it a versatile tool for any DIYer.
- USER-FRIENDLY APP - Our accompanying app is easy to use and navigate, with clear and concise information displayed in an easy-to-understand format. Available on IOS and Android.
- [ABS & SRS Scanner with Active Test] The ABS/ SRS diagnostic tool Read & clear DTCs, displays live data in a graph to locate the cause of faults and assists the home mechanic with repairs and clearing ABS and airbag warning lights. Active test sensors, valves or solenoids etc. and tracks any threats in real time. It is invaluable to have a diagnostic tool with Active Test feature that you will never find on similar ABS/ SRS scanners.
- 【3 HOP Reset Services 】Easy to set up 3 regular reset services for Oil Light, Battery Management System, and Steering Angle Position. With this obd2 scanner, you can reset the oil service light and reset pre-programmed mileage intervals for energy efficiency; adjust or reset the steering angle position to keep steering aligned; and clear the original low battery fault information. No need to leave home for shop-quality car maintenance.
- 【All OBD2 Test Modes 】 This ABS & SRS scan tool is also a full featured obd2 code reader, allowing a quick test of the engine system of OBD II vehicles, can Read/Clear engine light codes, Live Data, Freeze Frame, Retrieving I/M Readiness Status, O2 Monitor Test, On-Board Monitor Test, Evap Test, Read Vehicle Information, and help pass smog test for most post-1996 OBD2/CAN vehicles.
- [DTC LookUp Library] Can't read the code? Go to the DTC LookUp Library. The Topdon AL600 OBD2 scanner offers a wealth of code definitions so you don't have to look them up in a list or database, and the HELP function takes you to diagnostic tips for possible fixes, saving time searching for repair materials online. No other scan tool or code reader under $100 offers this level of assistance.
- [User-Oriented] You'll love the feel of this automotive scanner, with black rubber grips all around the outer edges for durability and to withstand accidental drops. With its easy access menu, you can operate all functions in minutes with just a few button presses. The 3-color LEDs give you a intuitive indication of the OBD2 test results in a second. 3 shortcut keys, one key to read/clear DTCs and a one-touch smoke status check make it easy to use even for beginners.
- 🎉【2024 Upgraded Ver. of AL519/ ML519/ ML619】Autel develops the brand-new AutoLink AL619 as the advanced ver. of Autel ML519, AL519, AL319, MS309. This AL619 OBD2 scanner can scan ABS & SRS systems, and support 10 Modes of OBD II Diagnostics Function on Worldwide Vehicles to read, erase codes and turn off the MIL, ABS, SRS warning lights so that you can better maintain your car when related malfunctions occur and make your vehicle ready for the annual test.
- 🎉【Accurate ABS/ SRS Diagnostics Functions】The ABS/ SRS diagnostic function is used to retrieve and clear codes from the ABS/ SRS systems. It can read and clear DTCs, show definitions of each code, display live data of multiple sensors in the graph to locate fault causes, and assist home mechanics to do the proper repair and clear ABS & Airbag warning lights. Diagnoses ABS/ SRS system codes on most 1996 and newer major vehicle models. Please email 📩 immoautel @ outlook. com 📩 for help.
- 🎉【All 10 Modes of OBD II Diagnostics Function】The OBD II Diagnostics function is a fast-access option that allows you to carry out a quick test on the engine system of OBD II vehicles. Read Codes, Erase Codes, Live Data, Freeze Frame, Retrieving I/M Readiness Status, O2 Monitor Test, On-Board Monitor Test, DTC Lookup, Component Test, Viewing Vehicle Information, Modules Present.
- 🎉【Live Data and Freeze Frame Data】With Live Data functions, Autel AL619 OBD2 diagnostic code reader allows you to view the live PID (Parameter Identification Data) of the vehicle's computer module(s) in text, graph to check the status of various sensors. And Freeze Frame Data enables you to view the vehicle's operating parameters at the moment a DTC is detected. These information will aid the technician by allowing the parameters to be duplicated for diagnostic and repair purposes.
- 🎉【DTC Lookup Feature】Besides showing you the code’s definition while you are reading the diagnostic trouble codes, AL619 features comparably user-friendly DTC Lookup Function which enables you to retrieve the definitions of any error codes from the large database of AL619, saving you from the hassle of wasting time searching definition of every code via Google.
- ABS/SRS OBD2 Scanner > Enjoy this ABS OBD2 code reader to reveal exact issues underlying in your brake, airbag, and engine systems, test individual ABS/SRS sensors, valves, or solenoids to quickly locate malfunctions (compatible with GM, Nissan, Fiat, Benz, Volvo, Land Rover, BMW, USA Ford, please reach us for details.), making sure critical safety systems work in perfect harmony together against accidents to be safe than sorry. NOTE: Only support upgrade on windows.
- 3 Most Needed Service Functions > This OBD2 scanner guides you through step by step procedures to reset oil service light and programmed mileage intervals for engine efficiency (Oil Reset); to calibrate steering wheel position for vehicle’s traveling in a straight line (SAS Reset); to clear the original low battery fault information against coming battery failures or damage (BMS Reset); saving your needless visits to mechanics. NOTE: Not suitable for all models, please reach us for compatibility.
- Full OBD2 Diagnostics > Say goodbye to the hassle of manual check-ups via this srs code reader. Quickly correct Check Engine Light warning on most OBD2/CAN compatible vehicles. Easily access to your smog status with one simple click I/M Readiness; and being filled with features for live data readings, freeze frame data, plus EVAP system, onboard monitor test means this scan tool checks all daily car care boxes.
- Work Easier > Red-Yellow-Green LEDs in this OBD2 scanner quickly show the overall DTC status without toggling through menu selections. HELP hotkey takes you directly to detailed descriptions/tips. Read/Erase DTC, I/M readiness shortcuts are added for optimized operation, along with DTC Lookup library for interpreting codes, designing the SRS OBD2 code reader a pleasure to use right out of the package even for beginners.
- Helpful Service > Get instant, free lifetime access to the most recent updates to add new car models and troubleshooting bugs making the OBD2 scanner a long-term investment for any home mechanics. The extended 1 years of quality assurance sweetens the worry-free deal even further. Multilingual Menu: EN, FR, ES, DE, IT, RU, PT, and JP. NOTE: Only support upgrade on windows.
- 🔧【PLUG AND PLAY - EASY TO USE】 : ANCEL FX2000 car scanner only takes 3 steps to connect to the car for diagnosis without cumbersome operations. The latest FX2000 scan tool is equipped with a one-key diagnosis function, which can automatically identify the model and year of your car, and automatically diagnose the car. Even beginners can use it to read the data and find out what the fault codes mean.
- 🚗【FULL OBD-LEVEL DIAGNOSTICS TOOL】: Quickly determines the cause of engine system faults, reads current, permanent and pending codes. After the repair, clears the codes and turns off the warning light. In addition, the FX2000 engine code reader also displays important OBD II advanced data such as fuel, live data and other manufacturer-specific parameters in real time to ensure that the engine ECU is operating correctly and safely, saving vehicle owners a lot of time and money in maintenance.
- 🚙【TRANSMISSION FAULT DIAGNOSTIC TOOL】: Some noises come from the transmission? Ancel obd2 scanner will read fault codes, display live transmission system data (fluid temperature, fluid pump, clutch actuation, pressure, etc.), and ensures transmission performance is optimal for vehicle speed and load. It provides detailed TCM data of the vehicle, so you can quickly and accurately find existing or potential problems.
- 🚐【FIND OUT SRS WRONG】: ANCEL FX2000 automotive scanner is able to read and clear fault codes in the SRS (airbag) and turn off the warning light to make sure the system is working correctly and safely. This odb2 scanner also displays a live graphical data stream of the supplemental restraint system (air bag), which allows you to analyze and verify that the air bag system is working properly.
- 🚌【ABS OBD2 SCANNER】:The FX2000 diagnostic scanner for all vehicles can read and clear the Diagnostic Trouble Codes (DTC) data stream transmitted from the ABS. By retrieving the ABS code data, the obd scanner can check the various brake components and accurately diagnose problems.
Last update on 2024-03-02 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.
SEOCONTENT-START
s11 11-1. Maintenance Schedule . 473 11-2. Maintenance Precautions . 473 Before Checking or Servicing in the Engine Compartment 474 When Checking or Servicing in the Engine Compartment 475 When Checking or Servicing in the Engine Compartment While the Engine Is Running . 475 11-3. Maintenance Tips 475 Removing and Reinstalling Clips 475 11-4. Engine Hood 477 11-5. Engine Compartment Overview . 479 2.5 L Models. 479 2.4 L Models. 480 11-6. Engine Oil 481 Engine Oil Consumption . 481 Checking the Oil Level 481 Changing the Oil and Oil Filter 483 Recommended Grade and Viscosity 483 Synthetic Oil. 483 11-7. Cooling System. 484 Cooling Fan, Hose and Connections . 484 Engine Coolant. 485 11-8. Air Cleaner Element 486 Replacing the Air Cleaner Element 486 11-9. Spark Plugs . 488 Recommended Spark Plugs 488 11-10. Drive Belts . 489 11-11. Continuously Variable Transmission Fluid . 489 11-12. Front Differential Gear Oil and Rear Differential Gear Oil 489 Recommended Grade and Viscosity . 489 11-13. Brake Fluid.490 Checking the Fluid Level 490 Recommended Brake Fluid. 490 11-14. Brake Booster 491 11-15. Brake Pedal491 11-16. Replacement of Brake Pad .491 11-17. Tires and Wheels .492 Types of Tires 492 Tire Pressure Monitoring System (TPMS) (U.S. Spec. Models) 492 Tire Inspection . 494 Tire Pressures and Wear 494 Wheel Balance . 496 Wear Indicators 497 Rotational Direction of Tires. 497 Tire Rotation 498 Tire Replacement . 498 Wheel Replacement 499 11-18. Alloy Wheels 500 11-19. Windshield Washer Fluid 500 11-20. Replacement of Wiper Blades 501 Windshield Wiper Blade Assembly . 502 Window Wiper Blade Rubber 503 Rear Window Wiper Blade Assembly (Outback) . 503 Rear Window Wiper Blade Rubber (Outback) 504 11-21. Battery 505 Maintenance and Service 11 Maintenance and Service 11-22. Fuses . 506 11-23. Installation of Accessories. 507 11-24. Replacing Bulbs 508 Headlights (Models with LED Headlights) 508 Front Turn Signal Light . 508 Rear Combination Lights 509 Backup Light 511 Dome Light. 513 Map Lights. 513 Door Step Light 513 Cargo Area Light (Outback) 513 Trunk Light (Legacy) 514 Other Bulbs . 514 11-25. Replacing Battery 514 Replacing Battery of Access Key Fob. 515 Replacing Battery of Transmitter 516 Maintenance and Service 11-1. Maintenance Schedule s11aa U.S. models The scheduled maintenance items required to be serviced at regular intervals are shown in the “Warranty and Maintenance Booklet.” For details, read the separate “Warranty and Maintenance Booklet.” Canada models The scheduled maintenance items required to be serviced at regular intervals are shown in the “Warranty and Service Booklet.” For details, read the separate “Warranty and Service Booklet.” Except for U.S. and Canada models Some items of your vehicle are required to be serviced at scheduled intervals. For details about your maintenance schedule, read the separate “Warranty and Maintenance Booklet.” 11-2. Maintenance Precautions s11ab When maintenance and service are required, it is recommended that all work be done by an authorized SUBARU dealer. If you perform maintenance and service by yourself, you should familiarize yourself with the information provided in this section on general maintenance and service for your SUBARU. Incorrect or incomplete service could cause improper or unsafe vehicle operation. Any problems caused by improper maintenance and service performed by you are not eligible for warranty coverage. WARNING . Testing of an All-Wheel Drive vehicle must NEVER be performed on a single two-wheel dynamometer or similar apparatus. Attempting to do so will result in transmission damage and in uncontrolled vehicle movement and may cause an accident or injuries to persons nearby. . Always select a safe area when performing maintenance on your vehicle. . Always be very careful to avoid injury when working on the vehicle. Remember that some of the materials in the vehicle may be hazardous if improperly used or handled, for example, battery acid. . Your vehicle should only be serviced by persons fully competent to do so. Serious personal injury may result to persons not experienced in servicing vehicles. . Always use the proper tools and make certain that they are well maintained. . Never get under the vehicle supported only by a jack. Always use safety stands to support the vehicle. . Never keep the engine running in a poorly ventilated area, such as a garage or other closed areas. . Do not smoke or allow open flames around the fuel or battery. This will cause a fire. . Because the fuel system is under pressure, replacement of the fuel filter should be performed only by your SUBARU dealer. – CONTINUED – Maintenance Schedule 473 11 Maintenance and Service . Wear adequate eye protection to guard against getting oil or fluids in your eyes. If something does get in your eyes, thoroughly wash them out with clean water. . Do not tamper with the wiring of the SRS airbag system or seatbelt pretensioner system, or attempt to take its connectors apart, as that may activate the system or it can render it inoperative. NEVER use a circuit tester for these wiring. If your SRS airbag or seatbelt pretensioner needs service, consult your nearest SUBARU dealer. . Check the inside of the engine compartment to see if there are any cloths and tools left. If they are left inside, they may be a cause of malfunction and fire. NOTE SUBARU does not endorse the use of non-SUBARU approved flushing systems and strongly advises against performing these services on a SUBARU vehicle. Non-SUBARU approved flushing systems use chemicals and/or solvents which have not been tested or approved by SUBARU. SUBARU warranties do not cover any part of the vehicle which is damaged by adding or applying chemicals and/or solvents other than those approved or recommended by SUBARU. & Before Checking or Servicing in the Engine Compartment s11ab01 WARNING . Always stop the engine and apply the parking brake to prevent the vehicle from moving. . Always let the engine cool down. Engine parts become very hot when the engine is running and remain hot for some time after the engine is stopped. . Do not spill engine oil, engine coolant, brake fluid or any other fluid on hot engine components. This may cause a fire. . When the ignition switch is in the “ON” position, the cooling fan may operate suddenly even when the engine is stopped. If your body or clothes come into contact with a rotating fan, that could result in serious injury. To avoid risk of injury, perform the following precautions. – Models with push-button start system: Always turn the push-button ignition switch to the “OFF” position and confirm that the operation indicator on the switch is turned off. Then take the access key fob out from the vehicle. – Models without push-button start system: Always remove the key from the ignition switch. . Before performing any servicing on a vehicle equipped with a remote engine start system temporarily place that system in the service mode to prevent it from unexpectedly starting the engine. 474 Maintenance Precautions & When Checking or Servicing in the Engine Compartment s11ab03 CAUTION . Do not contact the belt cover while checking the components in the engine compartment. Doing so may cause your hand to slip off the belt cover and result in an unexpected injury. . Do not touch the oil filter until the engine has cooled down completely. Doing so may result in a burn or other injury. Note that the oil filter becomes very hot when the engine is running and remains hot for some time after the engine has stopped. & When Checking or Servicing in the Engine Compartment While the Engine Is Running s11ab02 WARNING A running engine can be dangerous. Keep your fingers, hands, clothing, hair and tools away from the cooling fan, belts and any other moving engine parts. Removing rings, watches and ties is advisable. 11-3. Maintenance Tips s11bi Some clips and fender linings must be removed before replacing the air cleaner elements or specific bulbs. & Removing and Reinstalling Clips s11bi01 ! Removing clips s11bi0101 There are several types of clips used for your vehicle. ! Type A and D clips s11bi010107 Type A clips – CONTINUED – Maintenance Tips 475 11 Maintenance and Service Type D clips 1. Turn the clips counterclockwise using a flat-head screwdriver until the center portion of the clip is raised. 2. Remove the clips with a flat-head screwdriver using leverage. ! Type B clips s11bi010102 1. Pull out the center portion of the clip using a flat-head screwdriver as shown in the illustration. 2. Pull the protruded center portion to remove the entire body of the clip. ! Type C clips s11bi010103 1. Turn the clip counterclockwise using a Phillips screwdriver until the center portion of the clip is raised. 2. Remove the entire clip by pulling it up. 476 Maintenance Tips ! Reinstalling clips s11bi0102 Type A clips Type B clips Type C clips Type D clips Insert the clip without the center portion first and then push the center portion of the clip into the hole. 11-4. Engine Hood s11ac CAUTION . Be extremely careful not to catch fingers or other objects when closing the engine hood. . Do not push the hood forcibly to close it. It could deform the metal. . Be extremely careful opening the engine hood when the wind is strong. The engine hood could close suddenly, possibly causing injuries from slamming. . Do not install accessories other than genuine SUBARU parts to the engine hood. If the engine hood becomes too heavy, the stay may not be able to support holding it open. . Check that the end of the hood stay is inserted into the slot. If it is not inserted properly, the hood may drop and cause injury. – CONTINUED – Engine Hood 477 11 Maintenance and Service To open the hood: 1. If the wiper blades are lifted off the windshield, return them to their original positions. 2. Pull the hood release knob under the instrument panel. 3. Release the secondary hood lock by moving the lever between the front grille and the hood toward the left. 4. Lift up the hood, release the hood prop from its retainer and put the end of the hood prop into the slot in the engine compartment. To close the hood: 1. Lift the hood slightly and remove the hood prop from the slot in the engine compartment and return the prop to its retainer. 2. Lower the hood to a height of approximately 5.9 in (15 cm) above its closed position and then let it drop. 3. After closing the hood, be sure the hood is securely locked. If this does not close the hood, release it from a slightly higher position. WARNING Always check that the hood is properly locked before you start driving. If it is not, it might fly open while the vehicle is moving and block your view, which may cause an accident and serious bodily injury. 478 Engine Hood 11-5. Engine Compartment Overview s11ad & 2.5 L Models s11ad08 1) Brake fluid reservoir (page 490) 2) Main fuse box (page 506) 3) Battery (page 505) 4) Windshield washer tank (page 500) 5) Engine oil filler cap (page 481) 6) Engine coolant reservoir (page 485) 7) Radiator cap (page 485) 8) Engine oil filter (page 483) 9) Engine oil level gauge (page 481) 10) Air cleaner case (page 486) – CONTINUED – Engine Compartment Overview 479 11 Maintenance and Service & 2.4 L Models s11ad17 1) Brake fluid reservoir (page 490) 2) Main fuse box (page 506) 3) Battery (page 505) 4) Windshield washer tank (page 500) 5) Engine oil filler cap (page 481) 6) Engine coolant reservoir (page 485) 7) Radiator cap (page 485) 8) Engine oil filter (page 483) 9) Engine oil level gauge (page 481) 10) Air cleaner case (page 486) 480 Engine Compartment Overview 11-6. Engine Oil s11ae CAUTION . If the level gauge is not pulled out easily, twist the level gauge right and left, then pull it out. Otherwise, you may be injured accidentally straining yourself. . Use only engine oil with the recommended grade and viscosity. . Be careful not to spill engine oil when adding it. If oil touches the exhaust pipe, it may cause a bad smell, smoke, and/or a fire. If engine oil gets on the exhaust pipe, be sure to wipe it off. & Engine Oil Consumption s11ae07 Some engine oil will be consumed while driving. The rate of consumption can be affected by such factors as transmission type, driving style, terrain and temperature. Under the following conditions, oil consumption can be increased and thus require refilling between maintenance intervals: . When the engine is new and within the break-in period . When the engine oil is of lower quality . When the incorrect oil viscosity is used . When engine braking is employed (repeatedly) . When the engine is operated at high engine speeds (for extended periods of time) . When the engine is operated under heavy loads (for extended periods of time) . When towing a trailer (Outback) . When the engine idles for extended periods of time . When the vehicle is operated in stop and go and/or heavy traffic situations . When the vehicle is used under severe thermal conditions . When the vehicle accelerates and decelerates frequently Under these or similar conditions, you should check your oil at least every 2nd fuel fill-up and change your engine oil more frequently. Different drivers in the same car may experience different results. If your oil consumption rate is greater than expected, contact your authorized SUBARU retailer who may perform a test under controlled conditions. & Checking the Oil Level s11ae01 1. Park the vehicle on a level surface and stop the engine. If you check the oil level just after stopping the engine, wait a few minutes for the oil to drain back into the oil pan before checking the level. 2.5 L models 1) Oil level gauge 2) Oil filler cap 3) Oil filter – CONTINUED – Engine Oil 481 11 Maintenance and Service 2.4 L models 1) Oil level gauge 2) Oil filler cap 3) Oil filter CAUTION If the level gauge is not pulled out easily, twist the level gauge right and left, then pull it out. Otherwise, you may be injured accidentally straining yourself. 2. Pull out the level gauge, wipe it clean, and insert it again. 3. Be sure the level gauge is correctly inserted until it stops. 2.5 L models 1) Full level 2) Low level 3) Approximately 1.1 US qt (1.0 liter, 0.9 Imp qt) from low level to full level 2.4 L models 1) Full level 2) Low level 3) Approximately 1.1 US qt (1.0 liter, 0.9 Imp qt) from low level to full level 4. Pull out the oil level gauge again. 5. Check the oil level on the gauge. If the oil level is below the low level mark, add oil so that the full level is reached. CAUTION . Be careful not to touch the engine oil filter when removing the oil filler cap. Doing so may result in a burn, a pinched finger, or may cause some other injury. . Use only engine oil with the recommended grade and vis- 482 Engine Oil cosity. . Be careful not to spill engine oil when adding it. If oil touches the exhaust pipe, it may cause a bad smell, smoke, and/or a fire. If engine oil gets on the exhaust pipe, be sure to wipe it off. To add engine oil, remove the engine oil filler cap and slowly pour engine oil through the filler neck. After pouring oil into the engine, you must use the level gauge to confirm that the oil level is correct. NOTE . To prevent overfilling the engine oil, do not add any additional oil above the full level when the engine is cold. . The engine low oil level warning light may stay illuminated when the engine is started straight after topping up or changing the engine oil. In such cases, park the vehicle on a level surface and wait for more than a minute until the oil level settles, after which the warning light will turn off. Refer to “Engine Low Oil Level Warning Indicator” FP179. & Changing the Oil and Oil Filter s11ae02 Change the oil and oil filter according to the maintenance schedule in the “Warranty and Maintenance Booklet.” NOTE . Changing the engine oil and oil filter should be performed by a well-trained expert. Contact your SUBARU dealer for changing the engine oil and oil filter. Fully trained mechanics are on standby at a SUBARU dealer to utilize the special tools, spare parts and recommended oil for this work, and also, used oils are properly disposed of. . If performing oil replacement yourself, observe the local regulations and dispose of waste oil properly. & Recommended Grade and Viscosity s11ae03 CAUTION Use only engine oil with the recommended grade and viscosity. Refer to “Engine Oil” FP522. NOTE Engine oil viscosity (thickness) affects fuel economy. Oils of lower viscosity provide better fuel economy. However, in hot weather, oil of higher viscosity is required to properly lubricate the engine. & Synthetic Oil s11ae05 You should use synthetic engine oil that meets the same requirements given for conventional engine oil. When using synthetic oil, you must use oil of the same classification, viscosity and grade shown in this Owner’s Manual. Refer to “Engine Oil” FP522. Also, you must follow the oil and filter changing intervals shown in the Warranty and Maintenance booklet. NOTE Synthetic oil of the grade and viscosity noted in chapter 12 is the recommended engine oil for optimum engine performance. Conventional oil may be used if synthetic oil is unavailable. Engine Oil 483 11 Maintenance and Service 11-7. Cooling System s11af WARNING Never attempt to remove the radiator cap until the engine has been shut off and has cooled down completely. Since the coolant is under pressure, you may suffer serious burns from a spray of boiling hot coolant when the cap is removed. CAUTION . Vehicles are filled at the factory with SUBARU Super Coolant that does not require the first change for 11 years/137,500 miles (11 years/220,000 km). This coolant should not be mixed with any other brand or type of coolant during this period. Mixing with a different coolant will reduce the life of the coolant. Should it be necessary to top off the coolant for any reason, use only SUBARU Super Coolant. If the SUBARU Super Coolant is diluted with another brand or type, the maintenance interval is shortened to that of the mixing coolant. . Do not splash the engine coolant over painted parts. The alcohol contained in the engine coolant may damage the paint surface. & Cooling Fan, Hose and Connections s11af03 Your vehicle employs an electric cooling fan which is thermostatically controlled to operate when the engine coolant reaches a specific temperature. 1) Normal operating range If the radiator cooling fan does not operate even when the engine coolant temperature gauge exceeds the normal operating range, the cooling fan circuit may be defective. Refer to “Engine Coolant Temperature Gauge” FP173. Check the fuse and replace it if necessary. Refer to “Fuses” FP506 and “Fuses and Circuits” FP528. If the fuse is not blown, have the cooling system checked by your SUBARU dealer. If frequent addition of coolant is necessary, there may be a leak in the engine cooling system. It is recommended that the cooling system and connections be checked for leaks, damage, or looseness. 484 Cooling System & Engine Coolant s11af02 ! Checking the coolant level s11af0201 1) “FULL” level mark 2) “LOW” level mark Check the coolant level at each fuel stop. 1. Check the coolant level on the outside of the reservoir while the engine is cool. 2. If the level is close to or lower than the “LOW” level mark, add coolant up to the “FULL” level mark. If the reserve tank is empty, remove the radiator cap and refill coolant up to just below the filler neck as shown in the following illustration. 1) Fill up to this level. 3. After refilling the reserve tank and the radiator, reinstall the cap and check that the rubber gaskets inside the radiator cap are in the proper position. CAUTION . Be careful not to spill engine coolant when adding it. If coolant touches the exhaust pipe, it may cause a bad smell, smoke, and/or a fire. If engine coolant gets on the exhaust pipe, be sure to wipe it off. . Do not splash the engine coolant over painted parts. The alcohol contained in the engine coolant may damage the paint surface. ! Changing the coolant s11af0202 It may be difficult to change the coolant. Have the coolant changed by your SUBARU dealer if necessary. The coolant should be changed according to the maintenance schedule in the “Warranty and Maintenance Booklet.” Cooling System 485 11 Maintenance and Service 11-8. Air Cleaner Element s11ag WARNING Do not operate the engine with the air cleaner element removed. The air cleaner element not only filters intake air but also stops flames if the engine backfires. If the air cleaner element is not installed when the engine backfires, you could be burned. CAUTION When replacing the air cleaner element, use a genuine SUBARU air cleaner element. If it is not used, there is the possibility of causing a negative effect to the engine. The air cleaner element functions as a filter screen. When the element is perforated or removed, engine wear will be excessive and engine life shortened. The air cleaner element is a dry type. It is unnecessary to clean or wash the element. & Replacing the Air Cleaner Element s11ag01 Replace the air cleaner element according to the maintenance schedule in the “Warranty and Maintenance Booklet.” Under extremely dusty conditions, replace it more frequently. It is recommended that you always use genuine SUBARU parts. ! 2.5 L models s11ag0111 1) Clip 1. Unsnap the two clips holding the air cleaner case (rear). 2. Open the air cleaner case and remove the air cleaner element. CAUTION If the inside of the air cleaner case is extremely soiled (for example, by sand), contact a SUBARU dealer and have the air cleaner case cleaned. 3. If you find large foreign objects such as leaves inside the air cleaner case, remove the foreign objects. 486 Air Cleaner Element 4. Install a new air cleaner element in the way the longitudinal side and the transverse side face as shown in the illustration. 5. To install the air cleaner case (rear), insert the three projections on the air cleaner case (rear) into the slits on the air cleaner case (front). 6. Install in the reverse order of removal. ! 2.4 L models s11ag0112 1) Clips 1. Unsnap the two clips holding the air cleaner case (rear). 2. Open the air cleaner case and remove the air cleaner element. CAUTION If the inside of the air cleaner case is extremely soiled (for example, by sand), contact a SUBARU dealer and have the air cleaner case cleaned. 3. If you find large foreign objects such as leaves inside the air cleaner case, remove the foreign objects. – CONTINUED – Air Cleaner Element 487 11 Maintenance and Service 4. Install a new air cleaner element in the way the longitudinal side and the transverse side face as shown in the illustration. 5. To install the air cleaner case (rear), insert the three projections on the air cleaner case (rear) into the slits on the air cleaner case (front). 6. Install the removed parts in the reverse order of removal. 11-9. Spark Plugs s11ah It may be difficult to replace the spark plugs. It is recommended that you have the spark plugs replaced by your SUBARU dealer. The spark plugs should be replaced according to the maintenance schedule in the “Warranty and Maintenance Booklet.” & Recommended Spark Plugs s11ah01 Refer to “Electrical System” FP526. 488 Spark Plugs 11-10. Drive Belts s11ai It is unnecessary to check the deflection of the drive belt periodically because your engine is equipped with an automatic belt tension adjuster. However, replacement of the belt should be done according to the maintenance schedule in the “Warranty and Maintenance Booklet.” Consult your SUBARU dealer for replacement. If the belt is loose, cracked or worn, contact your SUBARU dealer. 11-11. Continuously Variable Transmission Fluid s11ay There is no fluid level gauge. It is unnecessary to check the continuously variable transmission fluid level. However, if necessary, consult your SUBARU dealer for inspection. 11-12. Front Differential Gear Oil and Rear Differential Gear Oil s11bl It is not necessary to check the gear oil level. Check that there are no cracks, damage or leakage. However, the oil inspection should be performed according to the maintenance schedule in the “Warranty and Maintenance Booklet.” Consult your SUBARU dealer for details. & Recommended Grade and Viscosity s11bl01 Each oil manufacturer has its own base oils and additives. Never use different brands together. For details, refer to “Front Differential and Rear Differential Gear Oil” FP524. CAUTION Using a differential gear oil other than the specified oil may cause a decline in vehicle performance. Drive Belts 489 11 Maintenance and Service 11-13. Brake Fluid s11ao & Checking the Fluid Level s11ao01 WARNING . Never let brake fluid contact your eyes because brake fluid can be harmful to your eyes. If brake fluid gets in your eyes, immediately flush them thoroughly with clean water. For safety, when performing this work, wearing eye protection is advisable. . Brake fluid absorbs moisture from the air. Any absorbed moisture can cause a dangerous loss of braking performance. . If the vehicle requires frequent refilling, there may be a leak. If you suspect a problem, have the vehicle checked at your SUBARU dealer. CAUTION . When adding brake fluid, be careful not to allow any dirt into the reservoir. . Never splash the brake fluid over painted surfaces or rubber parts. Alcohol contained in the brake fluid may damage them. . Be careful not to spill brake fluid when adding it. If brake fluid touches the exhaust pipe, it may cause a bad smell, smoke, and/or a fire. If brake fluid gets on the exhaust pipe, be sure to wipe it off. Visually check the brake fluid level of the reservoir monthly on the even surface. 1) “MAX” level line 2) “MIN” level line Be sure to check the brake fluid level from the outside of the reservoir. If the fluid level is below “MIN”, top up brake fluid to “MAX”. Use only brake fluid from a sealed container. & Recommended Brake Fluid s11ao02 Refer to “Fluids” FP525. CAUTION Never use different brands of brake fluid together. Also, avoid mixing DOT 3 and DOT 4 brake fluids even if they are the same brand. 490 Brake Fluid 11-14. Brake Booster s11aq The brake booster utilizes the vacuum produced by the engine manifold to reduce the force required to depress the brake pedal. The vacuum in the brake booster may be insufficient if the brake pedal is depressed when the engine is stopped or after the vehicle has been parked for a long period of time. It such cases, it is necessary to depress the brake pedal using greater force than usual. 11-15. Brake Pedal s11ar Check the brake pedal free play and reserve distance according to the maintenance schedule in the “Warranty and Maintenance Booklet”. 11-16. Replacement of Brake Pad s11at CAUTION . If you continue to drive despite the scraping noise from the audible brake pad wear indicator, it will result in the need for costly brake rotor repair or replacement. . It is recommended that you disconnect the vehicle battery before replacing the brake pad. However, it is dangerous to disconnect the vehicle battery. We recommend that you have your SUBARU dealer replace the brake pad. – CONTINUED – Brake Booster 491 11 Maintenance and Service The disc brakes have audible wear indicators on the brake pads. If the brake pads wear close to their service limit, the wear indicator makes a very audible scraping noise when the brake pedal is applied. If you hear this scraping noise each time you apply the brake pedal, have the brake pads serviced by your SUBARU dealer as soon as possible. 11-17. Tires and Wheels s11av & Types of Tires s11av01 You should be familiar with type of tires present on your vehicle. ! All season tires s11av0101 The factory-installed tires on your new vehicle are all season tires. All season tires are designed to provide an adequate measure of traction, handling and braking performance in year-round driving including snowy and icy road conditions. However all season tires do not offer as much traction performance as winter (snow) tires in heavy or loose snow or on icy roads. All season tires are identified by “ALL SEASON” and/or “M+S” (Mud & Snow) on the tire sidewall. ! Summer tires s11av0102 Summer tires are high-speed capability tires best suited for highway driving under dry conditions. Summer tires are inadequate for driving on slippery roads such as on snow-covered or icy roads. If you drive your vehicle on snow-covered or icy roads, we strongly recommend the use of winter (snow) tires. When installing winter tires, be sure to replace all four tires. ! Winter (snow) tires s11av0103 Winter tires are best suited for driving on snow-covered and icy roads. However winter tires do not perform as well as summer tires and all season tires on roads other than snow-covered and icy roads. & Tire Pressure Monitoring System (TPMS) (U.S. Spec. Models) s11av02 The tire pressure monitoring system provides the driver with a warning message by sending a signal from a sensor that is installed in each wheel when tire pressure is severely low. The tire pressure monitoring system will activate only when the vehicle is driven. Also, this system may not react immediately to a sudden drop in tire pressure (for example, a blow-out caused by running over a sharp object). If you adjust the tire pressures in a warm garage and will then drive the vehicle in cold outside air, the resulting drop in tire pressures may cause the low tire pressure warning light to illuminate. To avoid this problem when adjusting the tire pressures in a warm garage, inflate the tires to pressures higher than those shown on the tire placard. Specifically, inflate them by an extra 1 psi (6.9 kPa, 0.07 kgf/cm2) for 492 Tires and Wheels every difference of 108F (5.68C) between the temperature in the garage and the temperature outside. By way of example, the following table shows the required tire pressures that correspond to various outside temperatures when the temperature in the garage is 608F (15.68C). Example: Tire size: 225/55R17 97V, 225/50R18 95V Standard tire pressures: Front: 33 psi (230 kPa, 2.3 kgf/cm2) Rear: 32 psi (220 kPa, 2.2 kgf/cm2) Garage temperature: 608F (15.68C) Outside temperature Adjusted pressure [psi (kPa, kgf/cm2)] Front Rear 308F (−18C) 36 (250, 2.5) 35 (240, 2.4) 108F (−128C) 38 (265, 2.65) 37 (255, 2.55) −108F (−238C) 41 (280, 2.8) 39 (270, 2.7) Example: Tire size: 225/65R17 102H, 225/60R18 100H Standard tire pressures: Front: 35 psi (240 kPa, 2.4 kgf/cm2) Rear: 33 psi (230 kPa, 2.3 kgf/cm2) Garage temperature: 608F (15.68C) Outside temperature Adjusted pressure [psi (kPa, kgf/cm2)] Front Rear 308F (−18C) 38 (260, 2.65) 36 (250, 2.5) 108F (−128C) 40 (275, 2.8) 38 (265, 2.65) −108F (−238C) 42 (290, 2.95) 41 (280, 2.8) If the low tire pressure warning light illuminates when you drive the vehicle in cold outside air after adjusting the tire pressures in a warm garage, re-adjust the tire pressures using the method described above. Then, increase the vehicle speed to at least 20 mph (32 km/h) and check to see that the low tire pressure warning light goes off a few minutes later. If the low tire pressure warning light does not go off, the tire pressure monitoring system may not be functioning normally. In this event, go to a SUBARU dealer to have the system inspected as soon as possible. While the vehicle is driven, friction between tires and the road surface causes the tires to warm up. After illumination of the low tire pressure warning light, any increase in the tire pressures caused by an increase in the outside air temperature or by an increase in the temperature in the tires can cause the low tire pressure warning light to go off. System resetting is necessary when the wheels are changed (for example, a switch to snow tires) and new TPMS valves are installed on the newly fitted wheels. Have this work performed by a SUBARU dealer following wheel replacement. It may not be possible to install TPMS valves on certain wheels that are on the market. Therefore, if you change the wheels (for example, a switch to snow tires), use wheels that have the same part number as the standard-equipment wheels. Without four operational TPMS valve/sensors on the wheels, the TPMS will not fully function and the warning light in the instrument panel will illuminate steadily after blinking for approximately one minute. When a tire is replaced, adjustments are necessary to ensure continued normal operation of the tire pressure monitoring system. As with wheel replacement, therefore, you should have the work performed by a SUBARU dealer. WARNING If the low tire pressure warning light does not illuminate briefly after the ignition switch is turned ON or the light illuminates steadily after blinking for approximately one minute, – CONTINUED – Tires and Wheels 493 11 Maintenance and Service you should have your Tire Pressure Monitoring System checked at a SUBARU dealer as soon as possible. If this light illuminates while driving, never brake suddenly. Instead, perform the following procedure. Otherwise an accident involving serious vehicle damage and serious personal injury could occur. 1) Keep driving straight ahead while gradually reducing speed. 2) Slowly pull off the road to a safe place. If this light still illuminates while driving after adjusting the tire pressure, a tire may have significant damage and a fast leak that causes the tire to lose air rapidly. If you have a flat tire, replace it with a spare tire as soon as possible. When a spare tire is mounted or a wheel rim is replaced without the original pressure sensor/transmitter being transferred, the low tire pressure warning light will illuminate steadily after blinking for approximately one minute. This indicates the TPMS is unable to monitor all four road wheels. Contact your SUBARU dealer as soon as possible for tire and sensor replacement and/ or system resetting. If the light illuminates steadily after blinking for approximately one minute, promptly contact a SUBARU dealer to have the system inspected. & Tire Inspection s11av03 Check on a daily basis that the tires are free from serious damage, nails, and stones. At the same time, check the tires for abnormal wear. Contact your SUBARU dealer immediately if you find any problem. NOTE . When the wheels and tires strike curbs or are subjected to harsh treatment as when the vehicle is driven on a rough surface, they can suffer damage that cannot be seen with the naked eye. This type of damage does not become evident until time has passed. Try not to drive over curbs, potholes or on other rough surfaces. If doing so is unavoidable, keep the vehicle’s speed down to a walking pace or less, and approach the curbs as squarely as possible. Also, make sure the tires are not pressed against the curb when you park the vehicle. . If you feel unusual vibration while driving or find it difficult to steer the vehicle in a straight line, one of the tires and/or wheels may be damaged. Drive slowly to the nearest authorized SUBARU dealer and have the vehicle inspected. & Tire Pressures and Wear s11av04 Maintaining the correct tire pressures helps to maximize the tires’ service lives and is essential for good running performance. Check and, if necessary, adjust the pressure of each tire and the spare (if equipped) at least once a month and before any long journey. 494 Tires and Wheels Tire placard Check the tire pressures when the tires are cold. Use a pressure gauge to adjust the tire pressures to the values shown on the tire placard. The tire placard is located on the door pillar on the driver’s side. Driving even a short distance warms up the tires and increases the tire pressures. Also, the tire pressures are affected by the outside temperature. It is best to check tire pressure outdoors before driving the vehicle. When a tire becomes warm, the air inside it expands, causing the tire pressure to increase. Be careful not to mistakenly release air from a warm tire to reduce its pressure. NOTE . The air pressure in a tire increases by approximately 4.3 psi (30 kPa, 0.3 kgf/cm2) when the tire becomes warm. . The tires are considered cold when the vehicle has been parked for at least 3 hours or has been driven less than 1 mile (1.6 km). WARNING Do not let air out of warm tires to adjust pressure. Doing so will result in low tire pressure. Incorrect tire pressures detract from controllability and ride comfort, and they cause the tires to wear abnormally. . Correctly inflated tires (tread worn evenly) Roadholding is good, and steering is responsive. Rolling resistance is low, so fuel consumption is also lower. – CONTINUED – Tires and Wheels 495 11 Maintenance and Service . Under inflated tires (tread worn at shoulders) Rolling resistance is high, so fuel consumption is also higher. . Over inflated tires (tread worn in center) Ride comfort is poor. Also, the tire magnifies the effects of road surface bumps and dips, possibly resulting in vehicle damage. WARNING Driving at high speeds with excessively low tire pressures can cause the tires to deform severely and to rapidly become hot. A sharp increase in temperature could cause tread separation, and destruction of the tires. The resulting loss of vehicle control could lead to an accident. & Wheel Balance s11av05 Each wheel was correctly balanced when your vehicle was new, but the wheels will become unbalanced as the tires become worn during use. Wheel imbalance causes the steering wheel to vibrate slightly at certain vehicle speeds and detracts from the vehicle’s straight-line stability. It can also cause steering and suspension system problems and abnormal tire wear. If you suspect that the wheels are not correctly balanced, have them checked and adjusted by your SUBARU dealer. Also have them adjusted after tire repairs and after tire rotation. CAUTION Loss of correct wheel alignment causes the tires to wear on one side and reduces the vehicle’s running stability. 496 Tires and Wheels Contact your SUBARU dealer if you notice abnormal tire wear. NOTE The suspension system is designed to hold each wheel at a certain alignment (relative to the other wheels and to the road) for optimum straight-line stability and cornering performance. & Wear Indicators s11av06 1) New tread 2) Worn tread 3) Tread wear indicator Each tire incorporates a tread wear indicator, which becomes visible when the depth of the tread grooves decreases to 0.063 in (1.6 mm). A tire must be replaced when the tread wear indicator appears as a solid band across the tread. WARNING When a tire’s tread wear indicator becomes visible, the tire is worn beyond the acceptable limit and must be replaced immediately. With a tire in this condition, driving at high speeds in wet weather can cause the vehicle to hydroplane. The resulting loss of vehicle control can lead to an accident. NOTE For safety, inspect the tire tread regularly and replace the tires before their tread wear indicators become visible. & Rotational Direction of Tires s11av11 Example of rotational direction marked on the sidewall 1) Front If the tires have specific rotational direction, refer to the arrow marked on the side wall. The arrow should be pointing forward direction when the wheels are fitted. – CONTINUED – Tires and Wheels 497 11 Maintenance and Service & Tire Rotation s11av07 Vehicles equipped with 4 nonunidirectional tires 1) Front Vehicles equipped with unidirectional tires 1) Front Tire wear varies from wheel to wheel. Move the tires to the positions shown in the illustration each time they are rotated. For the tire rotation schedule, refer to the “Warranty and Maintenance Booklet.” Replace any damaged or unevenly worn tire at the time of rotation. After tire rotation, adjust the tire pressures and make sure the wheel nuts are correctly tightened. After driving approximately 600 miles (1,000 km), check the wheel nuts again and retighten any nut that has become loose. & Tire Replacement s11av08 The wheels and tires are important and integral parts of your vehicle’s design; they cannot be changed arbitrarily. The tires fitted as standard equipment are optimally matched to the characteristics of the vehicle and were selected to give the best possible combination of running performance, ride comfort, and service life. It is essential for every tire to have a size and construction matching those shown on the tire placard and to have a speed symbol and load index matching those shown on the tire placard. Using tires of a non-specified size detracts from controllability, ride comfort, braking performance, speedometer accuracy and odometer accuracy. It also creates incorrect body-to-tire clearances and inappropriately changes the vehicle’s ground clearance. All four tires must be the same in terms of manufacturer, brand (tread pattern), construction, and size. You are advised to replace the tires with new ones that are identical to those fitted as standard equip- 498 Tires and Wheels ment. For safe vehicle operation, SUBARU recommends replacing all four tires at the same time. WARNING . When replacing or installing tire(s), all four tires must be the same for the following items. (a) Size (b) Speed symbol (c) Load index (d) Circumference (e) Construction (f) Manufacturer (g) Brand (tread pattern) (h) Degrees of wear For items (a) to (c), you must obey the specification that is printed on the tire placard. The tire placard is located on the driver’s door pillar. If all four tires are not the same in items (a) to (h), serious mechanical damage could be caused to the drivetrain of the car, and affect the followings. – Ride – Handling – Braking – Speedometer/Odometer calibration – Clearance between the body and the tires It also may be dangerous and lead to loss of vehicle control, and it can lead to an accident. . Use only radial tires. Do not use radial tires together with belted bias tires and/or bias-ply tires. Doing so can dangerously reduce controllability, resulting in an accident. & Wheel Replacement s11av09 When replacing wheels due, for example, to damage, make sure the replacement wheels match the specifications of the wheels that are fitted as standard equipment. Replacement wheels are available from SUBARU dealers. WARNING Use only those wheels that are specified for your vehicle. Wheels not meeting specifications could interfere with brake caliper operation and may cause the tires to rub against the wheel well housing during turns. The resulting loss of vehicle control could lead to an accident. Tires and Wheels 499 11 Maintenance and Service 11-18. Alloy Wheels s11bm Alloy wheels can be scratched and damaged easily. Handle them carefully to maintain their appearance, performance, and safety. . When any of the wheels is removed and replaced for tire rotation or to change a flat, always check the tightness of the wheel nuts after driving approximately 600 miles (1,000 km). If any nut is loose, tighten it to the specified torque. . Never apply oil to the threaded parts, wheel nuts, or tapered surface of the wheel. . Never let the wheel rub against sharp protrusions or curbs. . When wheel nuts, balance weights, or the center cap is replaced, be sure to replace them with genuine SUBARU parts designed for alloy wheels. 11-19. Windshield Washer Fluid s11ax Windshield washer fluid warning light When there is only a small amount of washer fluid remaining, the windshield washer fluid warning light will appear. When this occurs, refill the washer fluid as follows. 1) “FULL” mark Remove the washer tank filler cap, then add fluid until it reaches the “FULL” mark on the tank. Use windshield washer fluid. If windshield washer fluid is unavailable use clean water. In areas where water freezes in winter, use an anti-freeze type windshield washer fluid. CAUTION Never use engine coolant as washer fluid because it could cause paint damage. If you fill the windshield washer tank with a fluid with a different concentration from the 500 Alloy Wheels one used previously, purge the old fluid from the piping between the windshield washer tank and washer nozzles by operating the washer for a certain period of time. Otherwise, if the concentration of the fluid remaining in the piping is too low for the outside temperature, it may freeze and block the nozzles. CAUTION . Adjust the washer fluid concentration appropriately for the outside temperature. If the concentration is inappropriate, sprayed washer fluid may freeze on the windshield and obstruct your view, and the fluid may freeze in the windshield washer tank. . State or local regulations on volatile organic compounds may restrict the use of methanol, a common windshield washer antifreeze additive. Washer fluids containing non-methanol antifreeze agents should be used only if they provide cold weather protection without damaging your vehicle’s paint, wiper blades or washer system. 11-20. Replacement of Wiper Blades s11az Grease, wax, insects, or other materials on the windshield or the wiper blade results in jerky wiper operation and streaking on the glass. If you cannot remove the streaks after operating the windshield washer or if the wiper operation is jerky, clean the outer surface of the windshield (or rear window) and the wiper blades using a sponge or soft cloth with a neutral detergent or mild abrasive cleaner. After cleaning, rinse the windshield and wiper blades with clean water. The windshield is clean if beads do not form when you rinse the windshield with water. CAUTION . Do not clean the wiper blades with gasoline or a solvent, such as paint thinner or benzine. This will cause deterioration of the wiper blades. . When you wish to raise the passenger- side wiper arm, first raise the driver-side wiper arm. Otherwise, the passenger-side wiper assembly and driver-side wiper assembly will touch each other, possibly resulting in scratches. . Return the passenger-side wiper arm to its original position before returning the driver-side wiper arm to its original position. Otherwise, the passenger-side wiper assembly and driver-side wiper assembly will touch each other, possibly resulting in scratches. . When returning the raised wipers to the original positions, return the wipers slowly on the windshield by hand. Returning the wipers from the detached positions by the spring operation might change the shape of the wiper arm or scratch the windshield. . While removing the wiper blades from the wiper arms, do not return the wiper arms to the original positions. Otherwise, the windshield surface may be scratched. If you cannot eliminate the streaking even after following this method, replace the wiper blades using the following procedures. – CONTINUED – Replacement of Wiper Blades 501 11 Maintenance and Service & Windshield Wiper Blade Assembly s11az01 NOTE Do not lower the wiper arm while the wiper blade assembly is removed. 1. Raise the wiper arm off the windshield. First raise the driver’s side wiper arm and then raise the front passenger’s side wiper arm. CAUTION Hold the wiper arm when replacing the wiper blade. Holding the wiper blade, may result in blade deformation. 1) Lock knob 2. Hold the wiper blade connection by hand, push the lock knob to release the lock, and then pull out the wiper blade assembly. NOTE Do not use a hard object to push the lock knob. The lock knob may be scratched. 3. When installing the wiper blade assembly, align it with the wiper arm connection part and then slide it in the opposite direction of removal to install. After installing the wiper blade assembly, check that the connection part is locked completely. 4. Hold the wiper arm by hand and slowly lower it in position. 502 Replacement of Wiper Blades & Window Wiper Blade Rubber s11az05 Replace the wiper blade rubber according to the following procedure. 1. Pull the wiper blade rubber until the slit on the underside of the wiper blade is in the removal position, as shown in the illustration, so that it can be removed. 2. Pull the end of the wiper blade rubber through the slit to remove it. 3. To install a new wiper blade rubber, perform the removal procedure in the reverse order. After installation, check that the tip of the wiper rubber has reached the end of the cap. NOTE It may be difficult to perform the wiper blade rubber replacement. We recommend that you contact your SUBARU dealer for wiper blade rubber replacement if necessary. & Rear Window Wiper Blade Assembly (Outback) s11az03 1. Raise the wiper arm off the rear window. 2. Turn the wiper blade assembly counterclockwise. – CONTINUED – Replacement of Wiper Blades 503 11 Maintenance and Service 3. Pull the wiper blade assembly toward you to remove it from the wiper arm. & Rear Window Wiper Blade Rubber (Outback) s11az04 1. Pull out the end of the blade rubber assembly to unlock it from the plastic support. 2. Pull the blade rubber assembly out of the plastic support. 1) Metal spines 3. If the new blade rubber is not provided with two metal spines, remove the metal spines from the old blade rubber and install them in the new blade rubber. 4. Align the claws of the plastic support with the grooves in the blade rubber assembly, then slide the blade rubber assembly into place. 504 Replacement of Wiper Blades Securely retain both ends of the rubber with the stoppers on the plastic support ends. If the rubber is not retained properly, the wiper may scratch the rear window glass. 5. Install the wiper blade assembly to the wiper arm. Make sure that it locks in place. 6. Hold the wiper arm by hand and slowly lower it in position. 11-21. Battery s11ba WARNING . Before beginning work on or near any battery, be sure to extinguish all cigarettes, matches, and lighters. Never expose a battery to an open flame or electric sparks. Batteries give off a gas which is highly flammable and explosive. . For safety, in case an explosion does occur, wear eye protection or shield your eyes when working near any battery. Never lean over a battery. . Do not let battery fluid contact eyes, skin, fabrics, or paint because battery fluid is a corrosive acid. If battery fluid gets on your skin or in your eyes, immediately flush the area with water thoroughly. Seek medical help immediately if acid has entered the eyes. If battery fluid is accidentally swallowed, immediately drink a large amount of milk or water, and seek medical attention immediately. . To lessen the risk of sparks, remove rings, metal watchbands, and other metal jewelry. Never allow metal tools to contact the positive battery terminal and anything connected to it WHILE you are at the same time in contact with any other metallic portion of the vehicle because a short circuit will result. . Keep everyone including children away from the battery. . Charge the battery in a wellventilated area. . Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Batteries also contain other chemicals known to the State of California to cause cancer. Wash hands after handling. CAUTION Never use more than 10 amperes when charging the battery because it will shorten battery life. – CONTINUED – Battery 505 11 Maintenance and Service It is unnecessary to periodically check the battery fluid level or periodically refill with distilled water. 11-22. Fuses s11bb CAUTION Never replace a fuse with one having a higher rating or with material other than a fuse because serious damage or a fire could result. The fuses are designed to melt during an overload to prevent damage to the wiring harness and electrical equipment. The fuses are located in two fuse boxes. One is located under the instrument panel behind the fuse box cover on the driver’s seat side. To remove the cover, pull it out. 1) Spare fuses 2) Fuse puller The other one (main fuse box) is housed in the engine compartment. Also, the spare fuses and fuse puller are stored in the fuse box cover. Pinch the upper part of the fuse puller when removing it from the main fuse box. 506 Fuses 1) Good 2) Blown If any lights, accessories or other electrical controls do not operate, inspect the corresponding fuse. If a fuse has blown, replace it. 1. Turn the ignition switch to the “LOCK”/ “OFF” position and turn off all electrical accessories. 2. Remove the fuse box cover. 3. Determine which fuse may be blown. Look at the back side of each fuse box cover and refer to “Fuses and Circuits” FP528. 4. Pull out the fuse with the fuse puller. 5. Inspect the fuse. If it has blown, replace it with a spare fuse of the same rating. 6. If the same fuse blows again, this indicates that its system has a problem. Contact your SUBARU dealer for repairs. 11-23. Installation of Accessories s11bd Always consult your SUBARU dealer before installing fog lights or any other electrical equipment in your vehicle. Such accessories may cause the electronic system to malfunction if they are incorrectly installed or if they are not suited for the vehicle. We recommend that you install only genuine SUBARU accessories on your vehicle. Installation of Accessories 507 11 Maintenance and Service 11-24. Replacing Bulbs s11be WARNING Bulbs may become very hot while illuminated. Before replacing bulbs, turn off the lights and wait until the bulbs cool down, Otherwise, there is the risk of sustaining a burn injury. CAUTION Replace any bulb only with a new bulb of the specified wattage. Using a bulb of different wattage could result in a fire. For the specified wattage of each bulb, refer to “Bulb Chart” FP532. For replacement, contact your SUBARU dealer. & Headlights (Models with LED Headlights) s11be18 The LED headlight warning light illuminates if the LED headlights malfunction. Have your vehicle inspected at a SUBARU dealer as soon as possible. & Front Turn Signal Light s11be03 Right-hand side Left-hand side 1. Turn the socket counterclockwise and pull it out. 508 Replacing Bulbs 2. Pull out the bulb from the socket and replace the bulb with a new one. & Rear Combination Lights s11be05 ! Legacy s11be0501 NOTE It may be difficult to replace the bulbs. We recommend that you have the bulbs replaced by your SUBARU dealer if necessary. 1. Undo the clips. For the method to undo the clips, refer to “Type C clips” FP476. 2. Remove the side cover. 3. Remove the upper and lower screws. 4. Slide the rear combination light assembly straight rearward and remove it from the vehicle. 1) Rear turn signal light 5. Remove the bulb holder from the rear combination light assembly by turning it – CONTINUED – Replacing Bulbs 509 11 Maintenance and Service counterclockwise. 6. Pull the bulb out of the bulb holder and replace it with a new one. 7. Set the bulb holder into the rear combination light assembly and turn it clockwise until it locks. 8. Reinstall the rear combination light assembly by sliding the two-pronged part of the combination light assembly securely to each holder of the vehicle side. 9. Tighten the upper and lower screws. 10. Reinstall the side cover. ! Outback s11be0502 1. Undo the clips. For the method to undo the clips, refer to “Type C clips” FP476. 2. Remove the side cover. 3. Remove the upper and lower screws. 510 Replacing Bulbs 4. Slide the rear combination light assembly straight rearward and remove it from the vehicle. 1) Rear turn signal light 2) Rear side marker light 5. Remove the bulb holder from the rear combination light assembly by turning it counterclockwise. 6. Pull the bulb out of the bulb holder and replace it with a new one. 7. Set the bulb holder into the rear combination light assembly and turn it clockwise until it locks. 8. Reinstall the rear combination light assembly by sliding the two-pronged part of the combination light assembly securely to each holder of the vehicle side. 9. Tighten the upper and lower screws. 10. Reinstall the side cover. & Backup Light s11be06 ! Legacy s11be0601 NOTE It may be difficult to replace the bulbs. We recommend that you have the bulbs replaced by your SUBARU dealer if necessary. 1. Open the trunk. – CONTINUED – Replacing Bulbs 511 11 Maintenance and Service 2. Remove the trunk trim lining by removing the clips indicated in the illustration. 3. Turn the bulb socket counterclockwise and remove it. 4. Pull the bulb out of the bulb socket and replace it with a new one. 5. Install the bulb socket by turning it clockwise. 6. Reconnect the electrical connector. 7. Reinstall the trunk trim lining. ! Outback s11be0602 1. Apply a flat-head screwdriver to the light cover as shown in the illustration, and pry the light cover off from the rear gate trim. 2. Turn the bulb socket counterclockwise and remove it. 3. Pull the bulb out of the bulb socket and replace it with a new one. 4. Install the bulb socket by turning it clockwise. 512 Replacing Bulbs 5. Install the light cover on the rear gate. & Dome Light s11be08 1. Remove the lens by prying the edge of the lens with a flat-head screwdriver. 2. Turn the bulb until the flat surfaces at its ends are aligned vertically. 3. Pull the bulb straight downward to remove it. 4. Install a new bulb. 5. Reinstall the lens. & Map Lights s11be09 CAUTION Replacing the bulb could cause burns since the bulb may be very hot. Have the bulb replaced by your SUBARU dealer. & Door Step Light s11be10 CAUTION Replacing the bulb could cause a short circuit. Have the bulb replaced by your SUBARU dealer. & Cargo Area Light (Outback) s11be11 1. Remove the lens by prying the edge of the lens with a flat-head screwdriver. 2. Pull the bulb out of the socket. 3. Install a new bulb. – CONTINUED – Replacing Bulbs 513 11 Maintenance and Service 4. Reinstall the lens. & Trunk Light (Legacy) s11be12 CAUTION Replacing the bulb could cause burns since the bulb may be very hot. Have the bulb replaced by your SUBARU dealer. & Other Bulbs s11be29 It may be difficult to replace the bulbs. We recommend that you have the bulbs replaced by your SUBARU dealer if necessary. 11-25. Replacing Battery s11bk The access key fob/transmitter battery may be discharged under the following conditions. . The operation of the keyless access function is unstable . The operating distance of the remote keyless entry system is unstable . The transmitter does not operate properly when used within the standard distance Replace the battery with a new one. CAUTION . Do not let dust, oil or water get on or in the access key fob/transmitter when replacing battery. . Be careful not to damage the printed circuit board in the access key fob/transmitter when replacing the battery. . Be careful not to allow children to touch the battery and any removed parts; children could swallow them. . There is a danger of an explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type of the battery. . Batteries shall not be exposed to excessive heat such as bright sunlight, fire or the like. NOTE . Replace only with the same or equivalent type of battery recommended by the manufacturer. . Dispose of used batteries according to the local laws. . Mount the battery in the correct orientation to prevent fluid leakage. Be careful not to bend the terminals. It may result in a malfunction. . It is recommended that the battery should be replaced by a SUBARU dealer. . Use a new battery. . After replacing the battery, confirm that the access key fob/transmitter functions properly. 514 Replacing Battery & Replacing Battery of Access Key Fob s11bk01 CAUTION . When removing or fitting the access key fob cover, make sure that the plastic part does not come off or become misaligned. . Before replacing the battery, remove any static electricity. Battery: Button battery CR2032 or equivalent 1) Release button 2) Emergency key 1. Take out the emergency key. 2. Wrap a flat-head screwdriver with vinyl tape or a cloth, and insert it in the gap to remove the cover. 3. Take out the battery using a flat-head screwdriver with vinyl tape or a cloth. 4. Insert a new battery with its positive (+) side facing upward as shown in the figure. 5. Attach the cover to the access key fob by fitting the projections and recesses together. – CONTINUED – Replacing Battery 515 11 Maintenance and Service & Replacing Battery of Transmitter s11bk02 CAUTION Before replacing the battery, remove any static electricity. Battery: Button battery CR1620 or equivalent 1. Open the key head using a flat-head screwdriver. 2. Remove the transmitter case from the key head. 3. Open the transmitter case by releasing the hooks. 1) Negative (−) side facing up 4. Replace the old battery with a new battery (type CR1620 or equivalent) making sure to install the new battery with the negative (−) side facing up. 5. Put together the transmitter case by fitting the hooks on the case. 6. Reinstall the transmitter case in the key head. 7. Refit the removed half of the key head. After the battery is replaced, the transmitter must be synchronized with the remote keyless entry system’s control unit. Press either the “ ” or “ ” button six times to synchronize the unit. 516 Replacing Battery s12 12-1. Specifications . 520 Dimensions 520 Engine 521 Fuel 521 Engine Oil 522 Front Differential and Rear Differential Gear Oil. 524 Fluids . 525 Engine Coolant. 525 Electrical System 526 Tires. 526 Brake Pedal 527 Brake Disc 527 Brake Pad. 527 12-2. Fuses and Circuits 528 Fuse Panel Located in the Passenger Compartment . 528 Main Fuse Panel Located in the Engine Compartment . 530 12-3. Bulb Chart532 Safety Precautions . 532 Bulb Chart . 533 12-4. Vehicle Identification.535 12-5. Function Settings 536 Function Settings and Adjustments on the Center Information Display . 536 Individual Settings and Adjustments Excluding Center Information Display . 536 Function Settings and Adjustments Performed by a Dealer 536 Specifications 12 Specifications 12-1. Specifications s12aa These specifications are subject to change without notice. & Dimensions s12aa01 in (mm) Item Legacy Outback 2.5 L 2.4 L 2.5 L 2.4 L Drive system AWD Transmission type CVT Overall length 190.6 (4,840) 191.3 (4,860) Overall width 72.4 (1,840) 73.0 (1,855) Overall height 59.1 (1,500) 66.1 (1,680) Wheelbase 108.3 (2,750) 108.1 (2,745) Tread Front 62.2 (1,580) 61.8 (1,570) Rear 63.4 (1,610) 62.8 (1,595) Ground clearance*1 5.9 (150) 8.7 (220) *1: Measured with vehicle empty CVT: Continuously variable transmission AWD: All-Wheel Drive 520 Specifications & Engine s12aa02 Engine model FB25 (2.5 L, DOHC, non-turbo) FA24 (2.4 L, DOHC, turbo) Engine type Horizontally opposed, liquid cooled 4 cylinder, 4 stroke direct injection gasoline engine Horizontally opposed, liquid cooled 4 cylinder, 4-stroke direct injection gasoline engine Displacement cu-in (cc) 152 (2,498) 146 (2,387) Bore 6 Stroke in (mm) 3.70 6 3.54 (94.0 6 90.0) 3.70 6 3.39 (94.0 6 86.0) Compression ratio 12.0 : 1 10.6 : 1 Firing order 1 – 3 – 2 – 4 1 – 3 – 2 – 4 & Fuel s12aa08 Fuel requirement Fuel tank capacity Unleaded gasoline with 87 AKI (90 RON) or higher 18.5 US gal (70 liters, 15.4 Imp gal) – CONTINUED – Specifications 521 12 Specifications & Engine Oil s12aa12 For the checking, adding and replacing procedure or other details, refer to “Engine Oil” FP481. NOTE The procedure for changing the engine oil and oil filter should be performed by a properly-trained expert. It is recommended that you have this service performed by your SUBARU dealer. ! Approved engine oil s12aa1201 Always use the SUBARU approved engine oil. For further details, please contact your SUBARU dealer. If the approved engine oil is unavailable, use the alternative engine oil described on the next page. ! Alternative engine oil s12aa1202 If the SUBARU approved oil is unavailable, the following alternative oil can be used. NOTE . Each quantity indicated is only a guideline. The necessary quantity for replacement may differ slightly depending on the temperature and other factors. . In choosing an oil, you want the proper quality and viscosity, as well as one that will enhance fuel economy. Oils of lower viscosity provide better fuel economy. However, in hot weather, oil of higher viscosity is required to properly lubricate the engine. The following table lists the recommended viscosities and applicable temperatures. . When adding oil, different brands may be used together as long as they are the same API classification and SAE viscosity as those recommended by SUBARU. 522 Specifications Oil grade SAE viscosity No. and applicable temperature Engine oil capacity API (American Petroleum Institute) classification SN with the words “RESOURCE CONSERVING” or SN PLUS with the words “RESOURCE CONSERVING” or ILSAC (International Lubricant Specification Advisory Committee) GF-5, which can be identified with the ILSAC certification mark (Starburst mark) 0W-20 synthetic oil is the required oil for optimum engine performance and protection. Conventional oil may be used if synthetic oil is unavailable. *: If 0W-20 synthetic oil is not available, 5W-30 conventional oil may be used if you need to add oil. However, you should change to 0W-20 synthetic oil at the next oil change. 2.5 L models – Adding the oil from low level to full level: 1.1 US qt (1.0 liter, 0.9 Imp qt) – Changing the oil and oil filter: 4.4 US qt (4.2 liters, 3.7 Imp qt) 2.4 L models – Adding the oil from L to F level: 1.1 US qt (1.0 liter, 0.9 Imp qt) – Changing the oil and oil filter: 4.8 US qt (4.5 liters, 4.0 Imp qt) – CONTINUED – Specifications 523 12 Specifications & Front Differential and Rear Differential Gear Oil s12aa13 Oil Front differential gear oil Rear differential gear oil Oil grade . SUBARU Extra MT*3 . API classification GL-5 (75W-90)*4 2.5 L models and 2.4 L for Legacy: SUBARU Extra MT*3 or API classification GL-5 (75W-90*4) 2.4 L for Outback: API classification GL-5 (75W-90*3 or 90*4) SAE viscosity No. and applicable temperature . 75W-90* . 90 *: Recommended Oil capacity*1 1.3 US qt (1.2 liters, 1.1 Imp qt) 0.8 US qt (0.8 liters, 0.7 Imp qt) Remarks*2 “Front Differential Gear Oil and Rear Differential Gear Oil” FP489 “Front Differential Gear Oil and Rear Differential Gear Oil” FP489 *1: The indicated oil quantity is only a guideline. The necessary quantity for replacement may differ slightly depending on the temperature and other factors. After refilling the gearbox with oil, the oil level should be checked. *2: For more details about maintenance and service, refer to the indicated section. *3: The vehicle is filled at the factory with this type of differential gear oil. *4: You may use this type of differential gear oil. However, using this type of oil will detract from fuel efficiency. 524 Specifications & Fluids s12aa10 Fluid Fluid type*1 Fluid capacity*2 Remarks*3 Continuously variable transmission fluid Consult your SUBARU dealer. 2.5 L models: · Legacy: 11.9 US qt (11.3 liters, 9.9 Imp qt) · Outback: 12.4 US qt (11.7 liters, 10.3 Imp qt) 2.4 L models: · Legacy: 12.3 US qt (11.6 liters, 10.2 Imp qt) · Outback: 12.6 US qt (11.9 liters, 10.5 Imp qt) “Continuously Variable Transmission Fluid” FP489 Brake fluid FMVSS No. 116, DOT 3 or DOT 4 brake fluid “Brake Fluid” FP490 *1: Use one of the indicated types of fluid. *2: The indicated fluid quantity is only a guideline. The necessary quantity for replacement may differ slightly depending on the temperature and other factors. *3: For more details about maintenance and service, refer to the indicated section. & Engine Coolant s12aa11 Vehicle model Coolant capacity Coolant type 2.5 L models 9.5 US qt (9.0 liters, 7.9 Imp qt) SUBARU Super Coolant 2.4 L models 9.2 US qt (8.7 liters, 7.7 Imp qt) The indicated coolant quantity is only a guideline. The necessary quantity for replacement may differ slightly depending on the temperature and other factors. For more details about maintenance and service, refer to “Cooling System” FP484. – CONTINUED – Specifications 525 12 Specifications & Electrical System s12aa03 Battery type LN2 Alternator 2.5 L models: 12 V-150 A 2.4 L models: 12 V-190 A Spark plugs 2.5 L models DILKAR7Q8 (NGK) 2.4 L models SILKFR8A6 (NGK) & Tires s12aa05 Item Legacy Outback Tire size 225/55R17 97V 225/50R18 95V 225/65R17 102H 225/60R18 100H Wheel size 17 6 7J 17 6 7 1/2J 18 6 7 1/2J 17 6 7J 18 6 7J Pressure Front 33 psi (230 kPa, 2.3 kgf/cm2) 35 psi (240 kPa, 2.4 kgf/cm2) Rear 32 psi (220 kPa, 2.2 kgf/cm2) 33 psi (230 kPa, 2.3 kgf/cm2) Temporary spare tire/ Conventional tire Size T155/70 D17 110M T155/80 D17 101M*2 225/60 R18 100H*3 Pressure 60 psi (420 kPa, 4.2 kgf/cm2) 60 psi (420 kPa, 4.2 kgf/cm2)*2 Front: 35 psi (240 kPa, 2.4 kgf/cm2)*3 Rear: 33 psi (230 kPa, 2.3 kgf/cm2)*3 Wheel nut tightening torque 88.5 lbf·ft (120 N·m, 12.2 kgf·m)*1 *1: This torque is equivalent to applying approximately 88 to 110 lbf (40 to 50 kgf) at the end of the wheel nut wrench. If you have tightened the wheel nuts by yourself, have the tightening torque checked at the nearest automotive service facility as soon as possible. For the wheel nut tightening procedure, refer to “Changing a Flat Tire” FP444. *2: Models with temporary spare tire *3: Models with conventional tire 526 Specifications & Brake Pedal s12aa27 in (mm) Pedal clearance 2.68 (68)* Pedal free play 0.02 – 0.11 (0.5 – 2.7) *: Minimum value when pedal is operated with a force of 110 lbf (490 N, 50 kgf) & Brake Disc s12aa18 If you need information on the usage limit value of brake discs and the method for measuring them, we recommend that you consult your SUBARU dealer. & Brake Pad s12aa28 in (mm) Brake pad wear limit 0.06 (1.5) Specifications 527 12 Specifications 12-2. Fuses and Circuits s12ab & Fuse Panel Located in the Passenger Compartment s12ab01 Fuse panel Fuse rating Circuit 1 Empty 2 20 A CIGAR 3 7.5 A IG A-1 4 15 A AUDIO NAVI 5 10 A IG B-2 6 7.5 A METER IG (DCDC) 7 20 A 12 V SOCKET 8 10 A A/C IG 9 7.5 A ACC 10 7.5 A IG B-1 11 7.5 A EYE SIGHT (DCDC) 12 Empty 13 7.5 A IG A-3 14 Empty 15 Empty 16 7.5 A UNIT IG (DCDC) 17 7.5 A MIRROR ACC 18 Empty 19 10 A IG A-2 528 Fuses and Circuits Fuse panel Fuse rating Circuit 20 10 A SRS AIR BAG 21 7.5 A A/C IG (DCDC) 22 10 A EYE SIGHT 23 7.5 A IG A-4 24 7.5 A A/C ACC (DCDC) 25 7.5 A UNIT +B (DCDC) 26 10 A BACK UP 27 15 A SEAT HTR R 28 20 A TRAIL R.FOG 29 Empty 30 7.5 A BACK UP (DCDC) 31 7.5 A SMT (DCDC) 32 15 A MIRROR +B 33 7.5 A KEY SW A 34 Empty 35 7.5 A ILLUMI (DCDC) 36 7.5 A KEY SW B 37 15 A UNIT +B1 38 7.5 A UNIT +B2 – CONTINUED – Fuses and Circuits 529 12 Specifications & Main Fuse Panel Located in the Engine Compartment s12ab02 Fuse panel Fuse rating Circuit 1 Empty 2 7.5 A OBD 3 7.5 A STOP 4 10 A MB-B 5 7.5 A PU B/UP 6 30 A JB-B2 7 7.5 A M/B-IG1 8 7.5 A M/B-IG2 9 10 A M/B-IG3 10 7.5 A M/B-IG4 11 7.5 A HORN1 12 7.5 A HORN2 13 10 A TAIL 14 15 A HAZARD 15 20 A D/L 16 20 A F/P 17 Empty 18 Empty 19 10 A AVCS 530 Fuses and Circuits Fuse panel Fuse rating Circuit 20 15 A ETC 21 15 A TCU 22 7.5 A CVT SSR 23 10 A E/G2 24 15 A IG COIL 25 20 A O2 HTR 26 20 A DI 27 15 A E/G1 28 25 A MAIN FAN 29 15 A DEICER 30 30 A VDC SOL 31 15 A F-END 32 30 A F.WIP 33 25 A R.DEF 34 30 A BACKUP 35 20 A HTR 36 25 A SUB FAN 37 15 A R.WIP 38 20 A BLOWER 39 20 A BLOWER 40 10 A MB-A 41 Empty Fuses and Circuits 531 12 Specifications 12-3. Bulb Chart s12ac & Safety Precautions s12ac03 WARNING Bulbs may become very hot while illuminated. Before replacing bulbs, turn off the lights and wait until the bulbs cool down. Otherwise, there is a risk of sustaining a burn injury. CAUTION Replace any bulb only with a new bulb of the specified wattage. Using a bulb of different wattage could result in a fire. 532 Bulb Chart & Bulb Chart s12ac04 NOTE Lights A, B, C, D, E, F, G, H, I, J and K are the LED (Light Emitting Diode) type. Consult your SUBARU dealer for replacement. – CONTINUED – Bulb Chart 533 12 Specifications Wattage Bulb No. 1) Front turn signal lights 12 V-28 W 7444NA 2) Dome light 12 V-8 W 3) Vanity mirror lights 14 V-1.4 W HTU 4) Door step lights (if equipped) 12 V-5 W W5W 5) Cargo area light (Outback) 12 V-13 W SAE #912 6) Rear side marker lights (Outback) 12 V-5 W W5W 7) Backup lights 12 V-16 W W16W 8) Rear turn signal lights 12 V-21 W WY21W 9) Trunk light (Legacy) 12 V-3.8 W SAE #194 A) Front position lights Daytime running lights B) Map lights C) Low and high beam headlights D) Front fog lights (if equipped) E) Front side marker lights F) Side turn signal lights (if equipped) G) High-mounted stop light H) Tail lights (if equipped) I) License plate lights J) Tail and stop lights K) Rear side marker lights (Legacy) 534 Bulb Chart 12-4. Vehicle Identification s12ad 1) Emission control label 2) Certification and bar code label 3) Tire inflation pressure label (tire placard) 4) Vehicle identification number plate 5) Model number label 6) Fuel label 7) Air conditioner label Vehicle Identification 535 12 Specifications 12-5. Function Settings s12ag & Function Settings and Adjustments on the Center Information Display s12ag01 Setting adjustments can be manually changed within the center information display to meet your personal requirements. Refer to “Center Information Display (CID)” FP205. & Individual Settings and Adjustments Excluding Center Information Display s12ag02 For setting adjustments to the following items, refer to the appropriate page for details. Item Function Available settings Factory default setting Page Alarm system Alarm system Operation/Non-operation Operation 142 Remote keyless entry system Audible signal Operation/Non-operation Operation 133 & Function Settings and Adjustments Performed by a Dealer s12ag03 Item Function Available settings Factory default setting Alarm system Monitoring start delay time (after closing doors) 0 seconds/30 seconds 30 seconds Map lights/Dome light/Cargo area light (Outback) illumination ON/OFF OFF Keyless access with push-button Audible signal volume*2 Level 1 to 7 Level 5 Trunk open without key (Legacy) ON/OFF ON Remote keyless entry system Audible signal volume*2 Level 1 to 7 Level 5 Remote trunk open/power rear gate open function*1 Operation of trunk opening/power rear gate opening by remote transmitter/access key fob Non-operation/Pressing twice/Pressing and holding Pressing and holding Key lock-in prevention Key lock-in prevention Operation/Non-operation Operation Battery drainage prevention function Battery drainage prevention function Operation/Non-operation Operation 536 Function Settings Item Function Available settings Factory default setting Auto dimmer cancel Sensitivity of the operation of the auto dimmer cancel OFF/Min/Low/Mid/Hi/Max Mid High beam assist function*1 High beam assist function Operation/Non-operation Operation Reverse gear interlocked rear wiper*1 Reverse gear interlocked rear wiper operation Operation/Non-operation U.S.-spec. models: Non-operation Other models: Operation *1: If equipped *2: The audible signal volume cannot be set under level 5 for the warning chime. Function Settings 537 12 Specifications s13 13-1. For U.S.A. 540 13-2. Tire Information 540 Tire Labeling 540 Recommended Tire Inflation Pressure. 542 Glossary of Tire Terminology 543 Tire Care – Maintenance and Safety Practices . 547 Vehicle Load Limit – How to Determine . 548 Determining Compatibility of Tire and Vehicle Load Capacities 551 Adverse Safety Consequences of Overloading on Handling and Stopping and on Tires 551 Steps for Determining Correct Load Limit. 552 13-3. Uniform Tire Quality Grading Standards.552 TREADWEAR . 553 TRACTION AA, A, B, C . 553 TEMPERATURE A, B, C 553 13-4. Reporting Safety Defects (USA).554 Consumer Information and Reporting Safety Defects 13 Consumer Information and Reporting Safety Defects 13-1. For U.S.A. s13aa The following information has been compiled according to Code of Federal Regulations “Title 49, Part 575”. 13-2. Tire Information s13ab & Tire Labeling s13ab01 Many markings (e.g. Tire size, Tire Identification Number or TIN) are placed on the sidewall of a tire by tire manufacturers. These marking can provide you with useful information on the tire. ! Tire size s13ab0101 Your vehicle comes equipped with P-Metric tire size. It is important to understand the sizing system in selecting the proper tire for your vehicles. Here is a brief review of the tire sizing system with a breakdown of its individual elements. ! P Metric s13ab010101 With the P-Metric system, Section Width is measured in millimeters. To convert millimeters into inches, divide by 25.4. The Aspect Ratio (Section Height divided by Section Width) helps provide more dimensional information about the tire size. Example: (1) P = Certain tire type used on light duty vehicles such as passenger cars (2) Section Width in millimeters (3) Aspect Ratio (= section height 7 section width). (4) R = Radial Construction (5) Rim diameter in inches ! Load and Speed Rating Descriptions s13ab010102 The load and speed rating descriptions will appear following the size designation. They provide two important facts about the tire. First, the number designation is its load index. Second, the letter designation indicates the tire’s speed rating. 540 For U.S.A. Example: (6) Load Index: A numerical code which specifies the maximum load a tire can carry at the speed indicated by its speed symbol, at maximum inflation pressure. For example, “91” means 1,356 lbs (615 kg), “90” means 1,323 lbs (600 kg), “89” means 1,279 lbs (580 kg) WARNING Load indices apply only to the tire, not to the vehicle. Putting a load rated tire on any vehicle does not mean the vehicle can be loaded up to the tire’s rated load. (7) Speed Rating: An alphabetical system describing a tire’s capability to travel at established and predetermined speeds. For example, “V” means 149 mph (240 km/h) WARNING . Speed ratings apply only to the tire, not to the vehicle. Putting a speed rated tire on any vehicle does not mean the vehicle can be operated at the tire’s rated speed. . The speed rating is void if the tires are worn out, damaged, repaired, retreaded, or otherwise altered from their original condition. If tires are repaired, retreaded, or otherwise altered, they may not be suitable for original equipment tire designed loads and speeds. ! Tire Identification Number (TIN) s13ab0102 Tire Identification Number (TIN) is marked on the intended outboard sidewall. The TIN is composed of four groups. Here is a brief review of the TIN with a breakdown of its individual elements. (1) Manufacturer’s Identification Mark (2) Tire Size (3) Tire Type Code (4) Date of Manufacture The first two figures identify the week, starting with “01” to represent the first full week of the calendar year; the second two figures represent the year. For example, 0101 means the 1st week of 2001. ! Other markings s13ab0103 The following makings are also placed on the sidewall. ! Maximum permissible inflation pressure s13ab010301 The maximum cold inflation pressure to which this tire may be inflated. For example, “350 kPa (51 PSI) MAX. PRESS” – CONTINUED – Tire Information 541 13 Consumer Information and Reporting Safety Defects ! Maximum load rating s13ab010302 The load rating at the maximum permissible weight load for this tire. For example, “MAX. LOAD 615 kg (1,356 LBS) @ 350 kPa (51 PSI) MAX. PRESS.” WARNING Maximum load rating applies only to the tire, not to the vehicle. Putting a load rated tire on any vehicle does not mean the vehicle can be loaded up to the tire’s rated load. ! Construction type s13ab010303 Applicable construction of this tire. For example, “TUBELESS STEEL BELTED RADIAL” ! Construction s13ab010304 The generic name of each cord material used in the plies (both sidewall and tread area) of this tire. For example, “PLIES: TREAD 2 STEEL + 2 POLYESTER + 1 NYLON SIDEWALL 2 POLYESTER” ! Uniform Tire Quality Grading (UTQG) s13ab010305 For details, refer to “Uniform Tire Quality Grading Standards” FP552. & Recommended Tire Inflation Pressure s13ab02 ! Recommended cold tire inflation pressure s13ab0201 For the recommended cold tire inflation pressure for your vehicle’s tires, refer to “Tires” FP526. ! Vehicle placard s13ab0202 The vehicle placard is affixed to the driver’s side B-pillar. Example: 542 Tire Information The vehicle placard shows original tire size, recommended cold tire inflation pressure on each tire at maximum loaded vehicle weight, seating capacity and loading information. ! Adverse safety consequences of under-inflation s13ab0203 Driving at high speeds with excessively low tire pressures can cause the tires to flex severely and to rapidly become hot. A sharp increase in temperature could cause tread separation, and failure of the tire(s). Possible resulting loss of vehicle control could lead to an accident. ! Measuring and adjusting air pressure to achieve proper inflation s13ab0204 Check and, if necessary, adjust the pressure of each tire (including the spare) at least once a month and before any long journey. Check the tire pressures when the tires are cold. Use a pressure gauge to adjust the tire pressures to the specific values. Driving even a short distance warms up the tires and increases the tire pressures. Also, the tire pressures are affected by the outside temperature. It is best to check tire pressure outdoors before driving the vehicle. When a tire becomes warm, the air inside it expands, causing the tire pressure to increase. Be careful not to mistakenly release air from a warm tire to reduce its pressure. & Glossary of Tire Terminology s13ab03 . Accessory weight The combined weight (in excess of those standard items which may be replaced) of automatic transmission, power steering, power brakes, power windows, power seats, radio, and heater, to the extent that these items are available as factory-installed equipment (whether installed or not). . Bead The part of the tire that is made of steel wires, wrapped or reinforced by ply cords and that is shaped to fit the rim. . Bead separation A breakdown of the bond between components in the bead. . Bias ply tire A pneumatic tire in which the ply cords that extend to the beads are laid at alternate angles substantially less than 90 degrees to the centerline of the tread. . Carcass The tire structure, except tread and sidewall rubber which, when inflated, bears the load. . Chunking The breaking away of pieces of the tread or sidewall. . Cold tire pressure The pressure in a tire that has been driven less than 1 mile or has been standing for three hours or more. . Cord The strands forming the plies in the tire. – CONTINUED – Tire Information 543 13 Consumer Information and Reporting Safety Defects . Cord separation The parting of cords from adjacent rubber compounds. . Cracking Any parting within the tread, sidewall, or inner liner of the tire extending to cord material. . Curb weight The weight of a motor vehicle with standard equipment including the maximum capacity of fuel, oil and coolant, and if so equipped, air conditioning and additional weight optional engine. . Extra load tire A tire designed to operate at higher loads and higher inflation pressure than the corresponding standard tire. . Groove The space between two adjacent tread ribs. . Innerliner The layer(s) forming the inside surface of a tubeless tire that contains the inflating medium within the tire. . Innerliner separation The parting of the innerliner from cord material in the carcass. . Intended outboard sidewall (1) The sidewall that contains a whitewall, bears white lettering or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same molding on the other sidewall of the tire, or (2) The outward facing sidewall of an asymmetrical tire that has a particular side that must always face outward when mounting on a vehicle. . Light truck (LT) tire A tire designated by its manufacturer as primarily intended for use on lightweight trucks or multipurpose passenger vehicles. . Load rating The maximum load that a tire is rated to carry for a given inflation pressure. . Maximum inflation pressure The maximum cold inflation pressure to which a tire may be inflated. . Maximum load rating The load rating for a tire at the maximum permissible inflation pressure for that tire. . Maximum loaded vehicle weight The sum of: (a) Curb weight (b) Accessory weight (c) Vehicle capacity weight (d) Production options weight . Maximum permissible inflation pressure The maximum cold inflation pressure to which a tire may be inflated. . Measuring rim The rim on which a tire is fitted for physical dimension requirements. . Normal occupant weight 150 lbs (68 kg) times the number of occupants specified in the second column of Table 1 that is appended to the end of this section. . Occupant distribution Distribution of occupants in a vehicle as specified in the third column of Table 1 that is appended to the 544 Tire Information end of this section. . Open splice Any parting at any junction of tread, sidewall, or innerliner that extends to cord material. . Outer diameter The overall diameter of an inflated new tire. . Overall width The linear distance between the exteriors of the sidewalls of an inflated tire, including elevations due to labeling, decorations, or protective bands or ribs. . Passenger car tire A tire intended for use on passenger cars, multipurpose passenger vehicles, and trucks, that have a gross vehicle weight rating (GVWR) of 10,000 lbs (4,535 kg) or less. . Ply A layer of rubber-coated parallel cords. . Ply separation A parting of rubber compound between adjacent plies. . Pneumatic tire A mechanical device made of rubber, chemicals, fabric and steel or other materials, that, when mounted on an automotive wheel, provides the traction and contains the gas or fluid that sustains the load. . Production options weight The combined weight of those installed regular production options weighing over 5.1 lbs (2.3 kg) in excess of those standard items which they replace, not previously considered in curb weight or accessory weight, including heavy duty brakes, ride levelers, roof rack, heavy duty battery, and special trim. . Radial ply tire A pneumatic tire in which the ply cords that extend to the beads are laid at substantially 90 degrees to the centerline of the tread. . Recommended inflation pressure The cold inflation pressure recommended by a vehicle manufacturer. . Reinforced tire A tire designed to operate at higher loads and at higher inflation pressures than the corresponding standard tire. . Rim A metal support for a tire or a tire and tube assembly upon which the tire beads are seated. . Rim diameter Nominal diameter of the bead seat. . Rim size designation Rim diameter and width. . Rim type designation The industry of manufacturer’s designation for a rim by style or code. . Rim width Nominal distance between rim flanges. . Section width The linear distance between the exteriors of the sidewalls of an inflated tire, excluding elevations due to labeling, decoration, or protective bands. – CONTINUED – Tire Information 545 13 Consumer Information and Reporting Safety Defects . Sidewall That portion of a tire between the tread and bead. . Sidewall separation The parting of the rubber compound from the cord material in the sidewall. . Snow tire A tire that attains a traction index equal to or greater than 110, compared to the ASTM E-1136 Standard Reference Test Tire, when using the snow traction test as described in ASTM F-1805-00, Standard Test Method for Single Wheel Driving Traction in a Straight Line on Snow-and Ice-Covered Surfaces, and which is marked with an Alpine Symbol “ ” on at least one sidewall. . Test rim The rim on which a tire is fitted for testing, and it may be any rim listed as appropriate for use with that tire. . Tread That portion of a tire that comes into contact with the road. . Tread rib A tread section running circumferentially around a tire. . Tread separation Pulling away of the tread from the tire carcass. . Treadwear indicators (TWI) The projections within the principal grooves designed to give a visual indication of the degrees of wear of the tread. . Vehicle capacity weight The rated cargo and luggage load plus 150 lbs (68 kg) times the vehicle’s designated seating capacity. . Vehicle maximum load on the tire Load on an individual tire that is determined by distributing to each axle its share of the maximum loaded vehicle weight and dividing by two. . Vehicle normal load on the tire Load on an individual tire that is determined by distributing to each axle its share of the curb weight, accessory weight, and normal occupant weight (distributed in accordance with Table 1 that is appended to the end of this section) and dividing by 2. . Wheel-holding fixture The fixture used to hold the wheel and tire assembly securely during testing. 546 Tire Information Table 1 Occupant loading and distribution for vehicle normal load for various designated seating capacities Designated seating capacity, number of occupants Vehicle normal load, number of occupants Occupant distribution in a normally loaded vehicle 2 through 4 2 2 in front. 5 through 10 3 2 in front, 1 in second seat. 11 through 15 5 2 in front, 1 in second seat, 1 in third seat, 1 in fourth seat. 16 through 22 7 2 in front, 2 in second seat, 2 in third seat, 1 in fourth seat. & Tire Care – Maintenance and Safety Practices s13ab04 . Check on a daily basis that the tires are free from serious damage, nails, and stones. At the same time, check the tires for abnormal wear. . Inspect the tire tread regularly and replace the tires before their tread wear indicators become visible. When a tire’s tread wear indicator becomes visible, the tire is worn beyond the acceptable limit and must be replaced immediately. With a tire in this condition, driving at even low speeds in wet weather can cause the vehicle to hydroplane. Possible resulting loss of vehicle control can lead to an accident. – CONTINUED – Tire Information 547 13 Consumer Information and Reporting Safety Defects . To maximize the life of each tire and ensure that the tires wear uniformly, it is best to rotate the tires every 6,000 miles (10,000 km). Rotating the tires involves switching the front and rear tires on the righthand side of the vehicle and similarly switching the front and rear tires on the left-hand side of the vehicle. (Each tire must be kept on its original side of the vehicle.) Replace any damaged or unevenly worn tire at the time of rotation. After tire rotation, adjust the tire pressures and make sure the wheel nuts are correctly tightened. For information about the tightening torque and tightening sequence for the wheel nuts, refer to “Flat Tires” FP444. & Vehicle Load Limit – How to Determine s13ab05 The load capacity of your vehicle is determined by weight, not by available cargo space. The load limit of your vehicle is shown on the vehicle placard attached to the driver’s side B-pillar. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs” on your vehicle’s placard. The vehicle placard also shows seating capacity of your vehicle. The total load capacity includes the total weight of driver and all passengers and their belongings, any cargo, any optional equipment such as a trailer hitch, roof rack or bike carrier, etc., and the tongue load of a trailer. Therefore cargo capacity can be calculated by the following method. Cargo capacity = Load limit − (total weight of occupants + total weight of optional equipment + tongue load of a trailer (if applicable)) For towing capacity information and weight limits, refer to “Trailer Towing (Outback)” FP430. ! Calculating total and load capacities varying seating configurations s13ab0501 Calculate the available load capacity as shown in the following examples: Example 1A Vehicle capacity weight of the vehicle is 800 lbs (363 kg), which is indicated on the vehicle placard with the statement “The combined weight of occupants and cargo should never exceed 363 kg or 800 lbs”. For example, if the vehicle has one 548 Tire Information occupant weighing 154 lbs (70 kg) plus cargo weighing 551 lbs (250 kg). 1. Calculate the total weight. 2. Calculate the available load capacity by subtracting the total weight from the vehicle capacity weight of 800 lbs (363 kg). 3. The result of step 2 shows that a further 95 lbs (43 kg) of cargo can be carried. Example 1B For example, if a person weighing 176 lbs (80 kg) now enters the same vehicle (bringing the number of occupants to two), the calculations are as follows: 1. Calculate the total weight. 2. Calculate the available load capacity. 3. The total weight now exceeds the capacity weight by 81 lbs (37 kg), so the cargo weight must be reduced by 81 lbs (37 kg) or more. Example 2A (Outback only) CAUTION Legacy: Your vehicle is neither designed nor intended to be used for trailer towing. Therefore, never tow a trailer with your vehicle. – CONTINUED – Tire Information 549 13 Consumer Information and Reporting Safety Defects Vehicle capacity weight of the vehicle is 800 lbs (363 kg), which is indicated on the vehicle placard with the statement “The combined weight of occupants and cargo should never exceed 363 kg or 800 lbs”. For example, the vehicle has one occupant weighing 165 lbs (75 kg) plus cargo weighing 265 lbs (120 kg). In addition, the vehicle is fitted with a trailer hitch weighing 22 lbs (10 kg), to which is attached a trailer weighing 1,764 lbs (800 kg). 10% of the trailer weight is applied to the trailer tongue (i.e. Tongue load = 176 lbs (80 kg)). 1. Calculate the total weight. 2. Calculate the available load capacity. 3. The result of step 2 shows that a further 172 lbs (78 kg) of cargo can be carried. Example 2B (Outback only) CAUTION Legacy: Your vehicle is neither designed nor intended to be used for trailer towing. Therefore, never tow a trailer with your vehicle. For example, if a person weighing 143 lbs (65 kg) and a child weighing 40 lbs (18 kg) now enter the same vehicle (bringing the number of occupants to three), and a child restraint system weighing 11 lbs (5 kg) is installed in the vehicle for the 550 Tire Information child to use, the calculations are as follows: 1. Calculate the total weight. 2. Calculate the available load capacity. 3. The total weight now exceeds the capacity weight by 22 lbs (10 kg), so the cargo weight must be reduced by 22 lbs (10 kg) or more. & Determining Compatibility of Tire and Vehicle Load Capacities s13ab06 The sum of four tires’ maximum load ratings must exceed the maximum loaded vehicle weight (“GVWR”). In addition, sum of the maximum load ratings of two front tires and of two rear tires must exceed each axle’s maximum loaded capacity (“GAWR”). Original equipment tires are designed to fulfill those conditions. The maximum loaded vehicle weight is referred to Gross Vehicle Weight Rating (GVWR). And each axle’s maximum loaded capacity is referred to Gross Axle Weight Rating (GAWR). The GVWR and each axle’s GAWR are shown on the vehicle certification label affixed to the driver’s door. The GVWR and front and rear GAWRs are determined by not only the maximum load rating of tires but also loaded capacities of the vehicle’s suspension, axles and other parts of the body. Therefore, this means that the vehicle cannot necessarily be loaded up to the tire’s maximum load rating on the tire sidewall. & Adverse Safety Consequences of Overloading on Handling and Stopping and on Tires s13ab07 Overloading could affect vehicle handling, stopping distance, vehicle and tire as shown in the following. This could lead to an accident and possibly result in severe personal injury. . Vehicle stability will deteriorate. . Heavy and/or high-mounted loads could increase the risk of rollover. . Stopping distance will increase. . Brakes could overheat and fail. . Suspension, bearings, axles and other parts of the body could break or experience accelerated wear that – CONTINUED – Tire Information 551 13 Consumer Information and Reporting Safety Defects will shorten vehicle life. . Tires could fail. . Tread separation could occur. . Tire could separate from its rim. & Steps for Determining Correct Load Limit s13ab08 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined weight of the driver and passengers from XXX kg or XXX lbs. 4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if the “XXX” amount equals 1,400 lbs (635 kg) and there will be five 150 lbs (68 kg) passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (1,400 − 750 (5 6 150) = 650 lbs). 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. 13-3. Uniform Tire Quality Grading Standards s13ac This information indicates the relative performance of passenger car tires in the area of treadwear, traction, and temperature resistance. This is to aid the consumer in making an informed choice in the purchase of tires. Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: TREADWEAR 200 TRACTION AA TEMPERATURE A The quality grades apply to new pneumatic tires for use on passenger cars. However, they do not apply to deep tread, winter type snow tires, space-saver or temporary use spare tires, tires with nominal rim diameters of 12 inches or less, or to some limited production tires. All passenger car tires must con- 552 Uniform Tire Quality Grading Standards form to Federal Safety Requirements in addition to these grades. & TREADWEAR s13ac02 The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1- 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate. & TRACTION AA, A, B, C s13ac03 The traction grades, from highest to lowest, are AA, A, B and C. Those grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. WARNING The traction grade assigned to this tire is based on straightahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. & TEMPERATURE A, B, C s13ac04 The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law. WARNING The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure. Uniform Tire Quality Grading Standards 553 13 Consumer Information and Reporting Safety Defects 13-4. Reporting Safety Defects (USA) s13ah If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Subaru of America, Inc. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer, or Subaru of America, Inc. To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1- 888-327-4236 (TTY: 1-800-424- 9153); go to http://www.safercar. gov; or write to: Administrator, NHTSA, 1200 New Jersey Avenue, SE, West Building, Washington, DC 20590. You can also obtain other information about motor vehicle safety from http://www.safercar. gov. 554 Reporting Safety Defects (USA) s14 Index 14 Index 1 11.6-inch display models. P206 A Abbreviation P4 ABS (Anti-lock Brake System) . P346 Warning light . P181 Access key P113 Warning indicator. P187 Accessories P507 Accessory power outlet P302 Adjustable storage net P313 Air cleaner element P486 Air conditioner Automatic climate control P279 Manual climate control system P281 Air filtration system P287 Airflow selection P281 Alarm system P140 All-Wheel Drive warning light. P185 Alloy wheel . P500 Cleaning . P465 Antenna P292 Anti-lock Brake System (ABS) . P346 Arming the system . P140 Armrest P45 Assist grip. P305 AT OIL TEMP warning light . P180 Audio Antenna P292 Set. P292 Auto on/off headlights . P242 Sensor P243 Auto Start Stop system . P361 Indicator light . P195 OFF indicator light P194 Warning light . P194 Auto Vehicle Hold. P357 Auto Vehicle Hold function. P357 ON indicator light . P184 Operation indicator light P185 Auto Vehicle Hold ON . P184 Auto Vehicle Hold operation. P185 Automatic headlight beam leveler Warning light . P194 Automatic Locking Retractor/Emergency Locking Retractor (ALR/ELR) P47 B Battery Drainage prevention function . P139 Jump starting. P449 Replacement (access key) P515 Replacement (remote engine start transmitter) P334 Replacement (transmitter) . P516 Vehicle battery . P505 Booster seat P66 Bottle holder P301 Brake Assist . P345 Booster . P345, P491 Disc P527 556 Index Fluid P490, P525 Parking. P355 Pedal . P491 System . P345 Brake pad . P527 Brake system P345 Warning light . P182 Braking. P344 Tips P344 BSD/RCTA P374 Approach indicator light/warning buzzer P377 OFF indicator P195, P200, P379 Warning indicator. P195, P200, P380 Bulb Chart P532 Replacing . P508 C Camera Front View Monitor. P366 Rear view camera P369 Cargo area Cover . P308 Light P297, P513 Tie-down hooks . P312 Catalytic converter P411 Center Console P299 Center information display P468 Center information display (CID) 11.6-inch display models. P206 Dual 7.0-inch display models . P227 Changing Coolant . P485 Flat tire . P444 Oil and oil filter P483 Charge warning light. P179 CHECK ENGINE warning light/Malfunction indicator light . P178 Checking Coolant level . P485 Fluid level (brake fluid) P490 Fluid level (washer fluid) . P500 Oil level (engine oil) P481 Child restraint systems P57 Installation of a booster seat. P66 Installation with ALR/ELR seatbelt. P62 Lower and top tether anchorages P67 Top tether anchorages . P72 Child safety P5 Locks P143 Chime Key P167 Light . P241 Seatbelt P175 Cleaning Alloy wheels P465 Interior P467 Ventilation grille P286 Climate control system P273 Automatic P279 Manual . P281 Index 557 14 Index Clock P239 Coat hook . P306 Combination meter display (color LCD) P197 Console P299 Continuously variable transmission (CVT). P336 Fluid P489, P525 Oil temperature warning light (AT OIL TEMP) P180 Coolant P485, P525 Cooling system P484 Corrosion protection. P466 Crossbars . P424 Cup holder P300 Front passenger’s P300 Rear passenger’s P301 D Daytime running light system P247 Defogger P254 Defrosting . P285 Deicer P254 Differential gear oil Front . P489, P524 Rear P489, P524 Dimensions . P520 Disarming the alarm system P141 Disc brake pad wear warning indicators . P345 Dome light . P296, P513 Door Locks . P136 Open indicator light P185 Step light P513 Unlock selection function. P122 Double trip meter P172 Drive belts . P489 Driver Forcus . P394 Driver Monitoring System P394 Driving All-Wheel Drive warning light . P185 AWD vehicles P413 Drinking . P7 Drugs P7 Foreign countries . P412 Off road P414 Pets. P8 Snowy and icy roads P418 Tips . P341, P410, P413 Tired or sleepy P8 Winter. P416 Dual 7.0-inch display models . P227 E Electrical system P526 Electronic Brake Force Distribution (EBD) system P346 Warning P183 Electronic parking brake P355 Automatic release function by accelerator pedal P357 Indicator light . P183 Warning P183, P360 Emergency Locking Retractor (ELR). P47 Engine Compartment overview . P479 Coolant . P485, P525 558 Index Exhaust gas (carbon monoxide) . P6, P410 Hood P477 Low oil level warning indicator. P179 Oil. P481, P522 Overheating P451 Starting & stopping . P324, P327 Event data recorder . P10 Exterior care . P464 F Flat tires . P444 Floor mat P307 Fluid level Brake . P490 Continuously variable transmission P489 Fog light Bulb . P532 Indicator light. P194 Switch P249 Folding mirror switch P265 Front Differential gear oil P489, P524 Seatbelt pretensioners P54 Turn signal light . P508 View Monitor . P366 Front seats P28 Forward and backward adjustment P30 Head restraint adjustment . P36 Memory function P33 Power seat P31 Reclining P31 Seat heater and ventilation P284 Seat height adjustment (driver’s seat) P31 Front View Monitor . P366 Fuel P317 Consumption indicator P201 Economy hints . P410 Filler door and cap . P319 Filler lid and cap P319 Gauge P172 Requirements P317, P521 Fuses P506 Fuses and circuits P528 G GAWR (Gross Axle Weight Rating). P422 Glove box P299 GVWR (Gross Vehicle Weight Rating) P422 H Hands-free Power Rear Gate function. P157 Hazard warning flasher . P170, P440 Head restraint adjustment Front seat P36 Rear seat . P44 Headlight. P242 Beam leveler . P249 Bulb wattage . P532 Control switch P241 Flasher . P244 Indicator light . P194 Welcome lighting function P243 Index 559 14 Index Heated Steering Wheel system . P267 High beam assist function. P244 Indicator light. P193 High beam indicator light P193 High/low beam change (dimmer) . P244 Hill descent control P351 Indicator . P195 Hook Coat. P306 Convenient tie-down P312 Shopping bag P306 Towing and tie-down P452 Horn. P268 Hose and connections P484 I Ignition switch . P166 Light. P167 Illumination brightness control . P173 Immobilizer . P130 Indicator light (security indicator light). P192 Indicator light Auto Start Stop. P194, P195 Auto Start Stop OFF P194 Auto Vehicle Hold ON P184 Auto Vehicle Hold operation P185 BSD/RCTA OFF P195 Door open. P185 Driver Monitoring System OFF P196 Driver Monitoring System operation (green) P196 Driver Monitoring System temporary stop . P196 Electronic parking brake P183 Front fog light P194 Front passenger’s frontal airbag ON and OFF . P177 Headlight. P194 High beam P193 High beam assist . P193 Hill descent control. P195 Immobilizer P192 Security P192 Select lever/Gear position . P193 SI-DRIVE P193 Sonar audible alarm OFF P197 Turn signal P193 Vehicle Dynamics Control OFF P187 Vehicle Dynamics Control operation . P187 X-MODE . P195 Inside mirror P256 Interior lights P296 Internal trunk lid release handle . P147 J Jack-up point . P444 Jump starting . P449 K Key. P113 Number. P113 Reminder chime. P167 Replacement . P130 Keyless access with push-button start system . P113 Disabling keyless access functions. P125 560 Index Locking and unlocking doors P118 Warning chimes and warning indicator . P187 When access key does not operate properly. P456 Keyless entry system . P132 L Lap belt pretensioner . P55 LCA . P375 Leather seat materials P467 Lifting Cargo Cover P308 Light Backup P511 Cargo area P297, P513 Control switch . P241 Daytime running P247 Dome P296, P513 Door step P513 Front fog. P249 Front side marker P242 Ignition switch . P167 Map P296, P513 Rear combination. P509 Rear side marker light P509 Rear turn signal. P509 Trunk P514 Turn signal P250, P508, P509 Vanity mirror P298 Loading your vehicle P420 Low fuel warning light. P185 Low tire pressure warning light P180 Lower and top tether anchorage P67 M Maintenance Precautions . P473 Schedule. P473 Seatbelt . P53 Tips P475 Tools P441 Malfunction indicator light (check engine warning light) P178 Manual Climate control. P281 Climate control system P281 Mode (continuously variable transmission) P340 Seat P30 Map light . P296, P513 Maximum load limits . P430 Meters and gauges. P171 Mirror defogger P254 Mirrors P256 Moonroof. P159 N New vehicle break-in driving P410 O Odometer P171 Off road driving P414 Oil filter . P483 Oil level Engine P481 Warning light . P179 Index 561 14 Index Oil pressure warning light . P179 On-road and off-road driving . P9 Outside Mirror defogger P254 Mirrors P264 Overhead console P299 Overheating engine P451 P Parking. P355 Brake . P355 Tips P360 Periodic inspections . P412 Petrol fuel . P317 PIN code Access . P122 Power Outlets . P302 Outside mirrors. P264, P265 Rear gate . P150 Seat . P31 Steering P343 Steering warning light. P186 Windows. P143 Precautions against vehicle modification P56, P107 Preparing to drive P324 Push-button Ignition switch . P168 Starting and stopping engine. P327 R RAB (Reverse Automatic Braking) OFF indicator. P196 ON/OFF setting P392 Warning indicator . P196 RCTA P375 Rear Combination lights P509 Differential gear oil . P489, P524 Gate . P149 Turn signal light . P509 View camera . P369 Rear seat P40 Armrest P45 Folding down P41 Head restraint adjustment P44 Reclining P40 Rear view camera P369 Rear window Defogger. P254 Wiper and washer switch P253 Wiper blades . P503 Recommended Brake fluid. P525 Continuously variable transmission fluid P525 Engine oil P522 Front differential gear oil . P524 Rear differential gear oil P524 Spark plugs . P526 Refueling. P319 562 Index Remote engine start system P330 Remote keyless entry system P132 Replacement Brake pad and lining P491 Wiper blades . P501 Replacing Access key battery. P515 Air cleaner element P486 Battery of access key fob . P515 Lost transmitters (remote keyless entry system) P135 Remote engine start transmitter battery P334 Remote keyless entry transmitter battery P516 Replacing bulbs P508, P532 Backup light . P511 Cargo area light. P513 Dome light P513 Door step light. P513 Front turn signal light . P508 Headlight P508 LED headlight . P508 Map light P513 Rear combination light P509 Rear side marker light P509 Rear turn signal light P509 Trunk light. P514 Reverse Automatic Braking System . P383 Rocking the vehicle P420 Roof molding and crossbar . P422 Roof rails with integrated cross bars P424 S Safety Precautions when driving . P5 Symbol P4 Warnings P3 Seat Fabric . P467 Front . P28 Heater . P38 Height adjustment . P31 Memory function . P33 Power P31 Rear P40 Ventilation P39 Seatbelt. P5, P46 Fastening . P47 Maintenance. P53 Pretensioners . P54 Safety tips P46 Warning light and chime P175 Security Alarm system. P140 Immobilizer P130 Indicator light . P192 Select lever Position indicator P193 Shift lock function. P339 Shopping bag hook. P306 Shoulder pretensioners . P55 Index 563 14 Index SI-DRIVE P342 Indicator . P193 Indicator light. P193 SI-DRIVE mode. P342 Snow tires P419, P492 Snowy and icy roads P418 Sounding a panic alarm P134 Spark plugs P488, P526 Specifications P520 Speedometer. P171 SRS Curtain airbag . P98 Side airbag . P98 SRS airbag (Supplemental Restraint System airbag). P5, P75 SRS airbag system Monitors . P105 Servicing P106 Warning light . P177 Starting & stopping engine . P324, P327 State emission testing (U.S. only) P322 Steering Responsive Headlight P248 Steering wheel Lock P326, P329 Power. P343 Tilt/telescopic P267 Stop light P533 Storage compartment . P298 Sun shade P160 Sun visors. P297 Supplemental Restraint System airbag (SRS) P75 Synthetic leather upholstery. P468 T Tachometer P171 Temperature gauge. P173 Temperature warning light AT OIL TEMP P180 Temporary spare tire. P440 Tether (child restraint system) P67, P72 Tie-down hooks P452 Tire. P492, P526 Chains P420 Inspection . P494 Pressures and wear . P494 Replacement . P498 Rotation P498 Size and pressure P526 Types . P492 Tire pressure monitoring system (TPMS) . P353, P447, P492 Warning light . P180 Tires and wheels P492 Tools. P441 Top tether anchorages P67, P72 Towing P452 All wheels on the ground. P455 Flat-bed truck P455 Hooks . P452 Weight P430 564 Index Trailer Connecting . P428 Hitch (Outback) P427, P433 Towing (Legacy) P430 Towing (Outback). P430 Towing tips P435 Trip meter . P172 Trunk lid . P146 Release handle . P147 Trunk light. P514 Turn signal Indicator lights . P193 Lever P250 U Under-floor storage compartment. P313 USB power supply . P304 V Valet mode P142 Vanity mirror P298 Vehicle Capacity weight . P421 Identification P535 Symbols . P5 Vehicle Dynamics Control OFF indicator light . P187 Operation indicator light P186 System . P347 Warning light . P186 Ventilator P272 W Warning and indicator lights. P175 Warning chimes Keyless access with push-button start system . P187 Seatbelt P175 Warning light ABS P181 Access key P187 All-Wheel Drive P185 AT OIL TEMP P180 Auto Start Stop P194 Automatic headlight beam leveler. P194 Brake system. P182 BSD/RCTA P195 Charge . P179 CHECK ENGINE P178 Driver Monitoring System warning light (yellow) . P196 Engine hood open P185 Engine low oil level P179 Keyless access with push-button start system . P187 LED headlight P194 Low fuel P185 Low tire pressure . P180 Oil pressure. P179 Power steering. P186 Seatbelt P175 SRS airbag system P177 Steering Responsive Headlight P194 Vehicle Dynamics Control . P186 Windshield washer fluid P185 Warranties P2 Index 565 14 Index Warranties and maintenance. P430 Washing . P464 Waxing and polishing . P465 Wear indicators . P497 Welcome lighting function . P243 Wheel Alloy. P500 Balance P496 Nut tightening torque P526 Replacement . P499 Windows. P143 Windshield Washer fluid P500 Wiper and washer switches P252 Wiper blades . P502 Wiper deicer P254 Winter Driving P416 Tires P419, P492 Wiper and washer P251 Wiper deicer P254 X X-MODE. P350 Indicator . P195 566 Index GAS STATION REFERENCE S99AA & Fuel S99AA01 Use only unleaded gasoline with an octane rating of 87 AKI (90 RON) or higher. & Fuel octane rating S99AA02 ! RON S99AA0201 This octane rating is the Research Octane Number. ! AKI S99AA0202 This octane rating is the average of the Research Octane and Motor Octane numbers and is commonly referred to as the Anti Knock Index (AKI). & Limit of ethanol content S99AA09 2.5 L models: no more than 10% 2.4 L models: no more than 15% & Fuel tank capacity S99AA03 18.5 US gal (70 liters, 15.4 Imp gal) & Engine oil S99AA04 Always use the SUBARU approved engine oil. For further details, please contact your SUBARU dealer. If the approved engine oil is unavailable, use the alternative engine oil described as follows. . API classification SN with the words “RESOURCE CONSERVING” or SN PLUS with the words “RESOURCE CONSERVING” . or ILSAC GF-5, which can be identified with the ILSAC certification mark (Starburst mark) For the complete viscosity requirements, refer to “Engine Oil” FP522. & Engine oil capacity S99AA05 2.5 L models: 4.4 US qt (4.2 liters, 3.7 Imp qt) 2.4 L models: 4.8 US qt (4.5 liters, 4.0 Imp qt) The indicated oil quantity is only a guideline and is estimated based on a case when the engine oil is changed with an oil filter. After refilling the engine with oil, the oil level should be checked using an oil level gauge. For more details about maintenance and service, refer to “Engine Oil” FP481. & Cold tire pressure S99AA06 Refer to “Tires” FP526.
SEOCONTENT-END