“This site contains affiliate links for which OEMDTC may be compensated” |
NHTSA ID Number: 10163525
Manufacturer Communication Number: 06-68-19R
Summary
This Service Information bulletin announces instruction for application of additional lubrication between the brake caliper support and pad clips. This will prevent the pad from dragging due to corrosion buildup which may result in uneven or premature wear of the replacement brake pads. This additional instruction applies to all models with brake pads using the upper and lower pad clips and has been added to the brake pad installation procedures found in the related Service Manuals.
![Subaru Logo](/Uploads/Subaru-Logo.webp)
NUMBER: 06-68-19R
DATE: 01/25/19
REVISED: 07/11/19
APPLICABILITY: | Legacy / Outback- All Models Impreza- All Models Crosstrek- All Models WRX- All Models Forester- All Models BRZ- All Models Tribeca- All Models |
SUBJECT: | Proper Grease Application during Brake Pad Installation |
INTRODUCTION:
This Service Information bulletin announces instruction for application of additional lubrication between the brake caliper support and pad clips. This will prevent the pad from dragging due to corrosion buildup which may result in uneven or premature wear of the replacement brake pads. This additional instruction applies to all models with brake pads using the upper and lower pad clips and has been added to the brake pad installation procedures found in the related Service Manuals.
PART INFORMATION:
Use either p.n. K0777YA010, Molykote AS-880N Brake Grease or the equivalent supplied in the replacement brake pad kit.
NOTES:
- Part quantity 1 of K0777YA010 contains enough grease to repair 10 vehicles.
- Use p.n. SOA635318 (qty. 1) when submitting a related Warranty claim.
SERVICE PROCEDURE / INFORMATION:
REMINDER: Customer satisfaction and retention starts with performing quality repairs.
The EXAMPLE illustration shown below for reference is from a 2019MY Forester. The procedure below is applicable when replacing either FRONT or REAR brake pads.
- Before installing new brake pads, remove the pad clips and thoroughly clean the caliper support of any dirt, rust or corrosion, paying close attention to the areas where the clips are attached / seated.
REMINDER: Always support removed calipers and NEVER allow them to hang by the brake hose.
- Apply a thin coating of brake grease to the caliper support then refit the pad clips to the support.
- Apply a thin coating of brake grease to the ends of the new brake pads where they contact the pad clips.
- Follow the remainder of the service procedure for reassembly as provided in the applicable Service Manual.
138 Affected Products
Vehicles
MAKE | MODEL | YEAR |
SUBARU | B9 TRIBECA | 2006-2011 |
SUBARU | BRZ | 2013-2019 |
SUBARU | CROSSTREK | 2012-2019 |
SUBARU | FORESTER | 1995-2019 |
SUBARU | IMPREZA | 1995-2019 |
SUBARU | LEGACY | 1995-2019 |
SUBARU | OUTBACK | 1995-2019 |
SUBARU | WRX | 2002-2006, 2008-2019 |
1 Associated Document
Manufacturer Communications
NUMBER: 06-68-19R
DATE: 01/25/19
REVISED: 07/11/19
https://www.nhtsa.gov/recalls?nhtsaId=10163525
MC-10163525-0001.pdf 439.766KB
NHTSA ID Number: 10154419
Manufacturer Communication Number: 06-68-19
Summary
This Service Information bulletin announces instruction for application of additional lubrication between the brake caliper support and pad clips. This will prevent the pad from dragging due to corrosion buildup which may result in uneven or premature wear of the replacement brake pads. This additional instruction applies to all models with brake pads using the upper and lower pad clips and has been added to the brake pad installation procedures found in the related Service Manuals.
1 Associated Document
Manufacturer Communications
NUMBER: 06-68-19
DATE: 01/25/19
https://www.nhtsa.gov/recalls?nhtsaId=10154419
MC-10154419-9999.pdf 431.383KB
“This site contains affiliate links for which OEMDTC may be compensated” |
- 100% synthetic formula with ceramic solids forming a premium quality brake lubricant
- Resistant to moisture, corrosion and contaminants - will not wash out
- Silences brake noise across a much wider temperature range and maintains lubricant integrity
- Lasts longer and easily outperforms ordinary caliper greases and traditional disc brake quiet products
- Suggested applications include disc brake caliper hardware, pistons, brushings, rubber sleeves and seals
- Entire Brake Assembly Protection: Sil-Glyde Brake Lubricant is crafted for the complete brake assembly, ensuring compatibility with both plastic and rubber (EPDM & Nitrile), safeguarding various components effectively.
- Noise-Free, Smooth Operations: Experience the serenity of noise-free brake installation. This lubricant ensures smooth and easy disassembly, enhancing your vehicle's maintenance process without any hassles.
- Banish Disc Brake Squeal: Say goodbye to annoying disc brake squeal. Our brake lubricant works effectively to eliminate noise, ensure smooth operations, and augment your driving experience significantly.
- Ultimate Corrosion and Rust Protection: Elevate the longevity of your brake parts. This formula protects parts against corrosion and rust, while dampening vibrations between contact points, assuring extended and robust performance.
- Resilient in Extreme Conditions: Rely on a moisture-proof and heat-resistant solution, capable of withstanding temperatures over 425°F (218°C). Ensure your vehicle's optimal functionality even under harsh conditions with our robust lubricant.
- Enjoy compatibility with both plastic and rubber with our silicone-based brake assembly lubricant, ensuring versatile use and superior convenience in every application.
- Minimize unwanted noise and wear with our brake assembly lubricant that effectively dampens vibrations between various contact points within the brake system.
- Benefit from a moisture-proof solution; our brake lubricant resists heat up to a substantial 425 degrees Fahrenheit, ensuring optimal performance in various conditions.
- Perfect for entire brake assembly usage, ensuring enhanced compatibility and performance with both plastic and rubber components, making brake maintenance effortless.
- Conveniently packaged in a 4-ounce brush top can, our silicone-based brake assembly lubricant allows for precise application, ensuring that every part is adequately protected.
- Superior Lubrication: Brake caliper grease provides exceptional lubrication for brake guide pins, minimizing friction and wear. This results in smoother brake operation and extended component lifespan, contributing to safer driving conditions.
- High Temperature Resistance: Brake grease is formulated to withstand the extreme temperatures encountered in braking systems. Whether you're driving in stop-and-go traffic or descending steep slopes, brake grease lubricant maintains its integrity, preventing brake fade and ensuring consistent performance. Temperature Range: -20℃ to 600℃.
- Water and corrosion resistance: In harsh environmental conditions, brake grease protects brake guide pins from rust and corrosion. This prolongs the life of your braking components and reduces the risk of premature failure.
- Easy Application: Brake grease comes in a user-friendly packaging with brush designed for precise and effortless application. Simply apply a thin, even coat of brake caliper grease to the brake guide pins during routine maintenance to ensure peak performance. Do not mix with other grease.
- Customer Service Guaranteed - If you are not satisfied with our brake grease and pin grease, please contact us in your free time. You will get our sincere and positive response. Our job is to ensure that our customers are satisfied with their shopping.
- Contains molybdenum, PTFE and graphite for an extreme temperature range of -30F to 600F
- Use on every brake job
- Not VOC Compliant for California & OTC
- Synthetic grease prevents caliper binding, vibration and corrosion
- Synthetic grease prevents caliper binding, vibration and corrosion.
- Contains molybdenum, PTFE and graphite for an extreme temperature range of -40°F to 400°F.
- Resists moisture and will not washout.
- Plastic & rubber safe.
- Use on metal to metal contact points and sliding surfaces.
- Non-melting formula fortified with ceramic solids for maximum protection
- Ultra high temperature range of -50 F to 3000 F (-46 C to 1649 C)
- Long lasting protection that outperforms existing Caliper Grease and Disc Brake Quiet products
- Smoothes out operation for silent performance at all speeds
- Prevent seizing and galling of critical brake components
- Protects all moving caliper hardware, mating surfaces and backing plates.
- Contains the latest rust, oxidation and anti-wear additives.
- Provides lasting protection against friction, wear and corrosion.
- Ideal for high performance or racing applications.
- Works in extreme temp ranges from -50 to 3000°F
- Heat Resistant: SIL-Glyde 8 oz Tube is a high temp brake grease that can withstand extreme temperatures, making it a reliable brake parts lubricant for both DIYers and professional mechanics.
- Rust and Corrosion Protector: SIL-Gylde brake lube is more than just a brake caliper grease. It is a rust and corrosion protector that shields your brake system from damaging elements.
- Silicone Brake Lubricant: SIL-Glyde is a silicone brake lubricant that outperforms other brake greases on the market.
- Eliminate Brake Squeal: Say goodbye to annoying brake noises. Our brake lubricant grease works as a disc brake quiet that effectively eliminates brake squeal for a smoother and quieter drive.
- Moisture Proof: The SIL-Glyde 8 oz Tube is not just a brake and caliper grease. It is also moisture-proof, ensuring that your brake system is protected from moisture-related damage.
- High Temp Copper Anti-seize Grease For Threaded Fittings Bolts & Nuts; Brush Top Applicator Included!
- Reduces Galling, Seizing, Welding & Carbon Fusion Providing A Dry-Film of Protective Solids On Threads; Reducing Total Amount of Torque Needed For Easier Disassembly
- Calcium Sulfonate Thickened Grease; Copper Fortified Grease Compound Unaffected By Severe Temperatures, Vibration, Expansion And Contraction
- Excellent Brake Lube Antiseize For Brake Pins and Brake Cam Assemblies Subject To Extreme Conditions: Water, Steam, Chemicals, Extreme Pressure, Rust & Corrosion
- Protects: Nuts, Bolts, Screws, Sprockets, Chains, Spark Plugs, Gaskets, Valve Assemblies, Splines, Gears & Conveyors
Last update on 2024-06-08 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.
SEOCONTENT-START
Bulletin Number: 06-68-19R; Revised: 07/11/19 Page 1 of 2 Continued… NUMBER: 06-68-19R DATE: 01/25/19 REVISED: 07/11/19 APPLICABILITY: Legacy / Outback- All Models Impreza- All Models Crosstrek- All Models WRX- All Models Forester- All Models BRZ- All Models Tribeca- All Models SUBJECT: Proper Grease Application during Brake Pad Installation CAUTION: VEHICLE SERVICING PERFORMED BY UNTRAINED PERSONS COULD RESULT IN SERIOUS INJURY TO THOSE PERSONS OR TO OTHERS. Subaru Service Bulletins are intended for use by professional technicians ONLY. They are written to inform those technicians of conditions that may occur in some vehicles, or to provide information that could assist in the proper servicing of the vehicle. Properly trained technicians have the equipment, tools, safety instructions, and know-how to do the job correctly and safely. If a condition is described, DO NOT assume that this Service Bulletin applies to your vehicle, or that your vehicle will have that condition. Subaru of America, Inc. is ISO 14001 Compliant ISO 14001 is the international standard for excellence in Environmental Management Systems. Please recycle or dispose of automotive products in a manner that is friendly to our environment and in accordance with all local, state and federal laws and regulations. Continued… INTRODUCTION: This Service Information bulletin announces instruction for application of additional lubrication between the brake caliper support and pad clips. This will prevent the pad from dragging due to corrosion buildup which may result in uneven or premature wear of the replacement brake pads. This additional instruction applies to all models with brake pads using the upper and lower pad clips and has been added to the brake pad installation procedures found in the related Service Manuals. PART INFORMATION: Use either p.n. K0777YA010, Molykote AS-880N Brake Grease or the equivalent supplied in the replacement brake pad kit. NOTES: • Part quantity 1 of K0777YA010 contains enough grease to repair 10 vehicles. • Use p.n. SOA635318 (qty. 1) when submitting a related Warranty claim. SERVICE PROCEDURE / INFORMATION: REMINDER: Customer satisfaction and retention starts with performing quality repairs. SERVICE INFORMATION BULLETIN ATTENTION: GENERAL MANAGER q PARTS MANAGER q CLAIMS PERSONNEL q SERVICE MANAGER q IMPORTANT – All Service Personnel Should Read and Initial in the boxes provided, right. © 2019 Subaru of America, Inc. All rights reserved. Bulletin Number: 06-68-19R; Revised: 07/11/19 Page 2 of 2 The EXAMPLE illustration shown below for reference is from a 2019MY Forester. The procedure below is applicable when replacing either FRONT or REAR brake pads. • Before installing new brake pads, remove the pad clips and thoroughly clean the caliper support of any dirt, rust or corrosion, paying close attention to the areas where the clips are attached / seated. REMINDER: Always support removed calipers and NEVER allow them to hang by the brake hose. • Apply a thin coating of brake grease to the caliper support then refit the pad clips to the support. • Apply a thin coating of brake grease to the ends of the new brake pads where they contact the pad clips. • Follow the remainder of the service procedure for reassembly as provided in the applicable Service Manual. IMPORTANT REMINDERS: • SOA strongly discourages the printing and/or local storage of service information as previously released information and electronic publications may be updated at any time. • Always check for any open recalls or campaigns anytime a vehicle is in for servicing. • Always refer to STIS for the latest service information before performing any repairs.
**************************************************************************************************************
SEOCONTENT-END