| “This site contains affiliate links for which OEMDTC may be compensated” |
NUMBER: 11-153-15R
DATE: 01-22-15
REVISED: 05-27-15
| APPLICABILITY: | 2011-15MY Forester N/A Models |
| SUBJECT: | Reprogramming File Availability for Extended Engine Cranking |
INTRODUCTION
This bulletin announces availability of reprogramming files to address customer concerns of extended cranking time before the engine starts.
PACK FILE APPLICABILITY
| MODEL YEAR/ MODEL | TRANSMISSION | PAK FILE NAME | NEW ECM PART NUMBER | OLD ECM PART NUMBER | EMISSION SPEC. | NEW CID NUMBER |
|---|---|---|---|---|---|---|
| 2011MY | AT | 22765AB408.pak | 22765AB408 | 22765AB400 22765AB401 22765AB402 22765AB403 22765AB404 22765AB405 22765AB406 22765AB407 |
CAL | EP5DB00B |
| 22765AB428.pak | 22765AB428 | 22765AB420 22765AB421 22765AB422 22765AB423 22765AB424 22765AB425 22765AB426 22765AB427 |
FED | EP5DB00D | ||
| 2012MY | 22765AD395.pak | 22765AD395 | 22765AD390 22765AD391 22765AD392 22765AD393 22765AD394 |
CAL | EP5GC00b | |
| 22765AD414.pak | 22765AD414 | 22765AD410 22765AD411 22765AD412 22765AD413 |
FED | EP5GC00d | ||
| 2013MY | MT | 22765AE582.pak | 22765AE582 | 22765AE580 22765AE581 |
CAL | EP5H500a |
| AT | 22765AE572.pak | 22765AE572 | 22765AE570 22765AE571 |
CAL | EP5H500b | |
| MT | 22765AE602.pak | 22765AE602 | 22765AE600 22765AE601 |
FED | EP5H500c | |
| AT | 22765AE592.pak | 22765AE592 | 22765AE590 22765AE591 |
FED | EP5H500d | |
| 2014MY | CVT | 22765AE223.pak | 22765AE223 | 22765AE220 22765AE221 22765AE222 |
CAL | EA1M510B |
| MT | 22765AE213.pak | 22765AE213 | 22765AE210 22765AE211 22765AE212 |
EA1M510A | ||
| 2015MY | CVT | 22765AG753.pak | 22765AG753 | 22765AG750 22765AG751 22765AG752 |
EA1M810B | |
| MT | 22765AG743.pak | 22765AG743 | 22765AG740 22765AG741 22765AG742 |
EA1M810A |
SERVICE PROCEDURE / INFORMATION
NOTES:
SOA now highly recommends connecting the Midtronics GR8 Diagnostic Battery Charger to the vehicle and utilizing the Power Supply Mode feature anytime a vehicle control module is being reprogrammed. Once the GR8 is connected to the vehicle, as long as the battery is fully charged, it takes less than 3 minutes to boot-up the charger, select the Power Supply Mode, and have the battery voltage stabilized and ready for reprogramming.
VERY IMPORTANT: This information is applicable to the Midtronics GR8 Diagnostic Battery Charger ONLY. It does not apply to any other brand / type of “generic” battery charger 
whatsoever. ONLY the GR8 and its Power Supply Mode feature has been tested and approved by Subaru of America, Inc. (SOA).
- If the GR8 indicates the vehicle’s battery must be charged, charge the battery using the GR8 before proceeding to reprogram the vehicle while using the Power Supply Mode.
- Control module failures as a result of battery discharge during reprogramming are not a matter for warranty. Should any DTCs reset after the reprogramming update is performed, diagnose per the procedure outlined in the applicable Service Manual.
WARRANTY / CLAIM INFORMATION
For vehicles within the Basic New Car Limited and / or Emissions Warranty period, this repair may be submitted using the following claim information:
| LABOR DESCRIPTION | LABOR OPERATION # |
FAIL CODE |
LABOR TIME |
|---|---|---|---|
| MFI OBDII ECM Reprogramming | A455-288 | UPG-48 | 0.4 |
NOTE: The pack file listings provided in this bulletin are the latest available at the time of publishing. Updates are often released thereafter without revision to the original bulletin. For this reason, it is critical to always have the latest version of Select Monitor III software installed on your system. You can confirm if a later version is available by entering the CID listed in this bulletin into FlashWrite. If a newer CID is shown as available in FlashWrite, reprogram using that file.
REMINDER: SOA strongly discourages the printing and/or local storage of service information as previously released information and electronic publications may be updated at any time.
- Always refer to STIS for the latest service information before performing any repairs.
J2534 Reprogramming
Subaru reprogramming files using a generic (non-OEM) SAEJ2534 pass-thru vehicle programming device are available by contacting Service Technical Information Company toll free at 1-866-428-2278. The cost for the CD-ROM with all reprogramming files is $75.00 plus S/H and applicable state tax. Files will be updated four (4) times per year, in CD-ROM format, with all available reprogramming service information at the same above offered cost. Authorized Subaru Dealers are provided the same reprogramming information.
Before purchasing, the reprogramming details can be found in the following Reprogramming J-2534 Files chart. Click the link to view the PDF chart.
Subaru J2534 Reprogramming software meets the latest available J2534-1 specification. Our Reprogramming J2534 Files chart does not specify the Calibration Identification Number (CID); however, this information is included in our offered CD-Rom.
Note: The ECM or TCM
being reprogrammed may already contain some or all of the reprogramming files listed in the Reprogramming J2534 Files chart shown by release date. It is possible to damage the vehicles ECM/TCM during the reprogramming event. Once the reprogramming process has started, it is recommended not to interrupt the process until the event is completed. If you experience any problems, please contact your scan tool maker for further instructions.
Are all pre-2004MY Subaru vehicles compatible with J2534?
No. Subaru has no reprogramming capability for model years 1996-1998. Starting with our 1999 model year, please see our Reprogramming Pre-J2534 Files chart for affected model reprogramming information.
Both pre-J2534 reprogramming and J2534 pass thru reprogramming files are included in the offered HDS kit software for aftermarket service provider application.
