“This site contains affiliate links for which OEMDTC may be compensated” |
NHTSA ID Number: 10185067
Manufacturer Communication Number: 12-305-20
Summary
This bulletin announces a design change made to the front hood air intake duct.
NUMBER: 12-305-20
DATE: 12/07/2020
APPLICABILITY: | 2015-20MY WRX and WRX STI |
SUBJECT: | Front Hood Intake Duct- Design Change |
INTRODUCTION:
This bulletin announces a design change made to the front hood air intake duct used on the models listed above. The new duct utilizes larger holes at the attachment points to facilitate the use of mounting bolts with a larger shoulder (boss) diameter as shown (in green) in the illustrations below. For this reason, the new mounting bolts are not interchangeable and cannot be used with the original style duct.
PRODUCTION CHANGE INFORMATION:
The new duct and mounting bolts were incorporated into production starting with VIN L9819487.
PART INFORMATION:
- New Mounting Bolt: 901020030
- New Duct-Inner Front Hood: 57253VA011
REMINDER: Always order the most up-to-date replacement parts based on the specific VIN being repaired.
SERVICE PROCEDURE / INFORMATION:
REMINDER: Customer satisfaction and retention starts with performing quality repairs.
The service procedures for hood duct replacement remain unchanged. Always refer to the applicable Service Manual and review the full requirements of the repair being performed. Service Manual procedures contain information critical to performing an effective repair the first time, every time. This includes but is not limited to important SAFETY precautions, proper inspection criteria, necessary special tools, required processes and related one-time-use parts needed for a complete and lasting repair.
12 Affected Products
Vehicles
MAKE | MODEL | YEAR |
SUBARU | WRX | 2015-2020 |
SUBARU | WRX STI | 2015-2020 |
1 Associated Document
Manufacturer Communications
NUMBER: 12-305-20
DATE: 12/07/2020
https://www.nhtsa.gov/recalls?nhtsaId=10185067
MC-10185067-0001.pdf 1110.067KB
“This site contains affiliate links for which OEMDTC may be compensated” |
- FITMENT - Compatible with 2015-2021 Subaru WRX, 2015-2021 Subaru WRX STI. Please make sure your car year and model before purchasing.
- EXTERIOR DESIGN - This is a full replacement that is held down with bolts in the front and 3M tape on the sides and rear. The set included mesh grille to match the scoop. It adds style to your car, personalize and upgrade your car, makes your car much more luxury looking.
- IMPROVE PERFORMANCE - Come with Carbon Fiber Style. The scoop helps the engine to dissipate heat, promote air circulation, maximize heat removal, and ensure the performance of the car.
- HIGH-DENSITY MATERIAL - Made of high density ABS Plastic for outdoor use. It has a good texture and is durable and impact resistant. It will not age or crack in a few months. To the maximum extent, ensure strength and durability for long lasting usage.
- PACKAGE INCLUDED - 1 x Hood Bonnet Scoop with Mesh Grille, Mounting Hardware (As Pictures) and Instruction. It is fixed with 3M double-sided tape, you need to apply the attached adhesive on the hood first, and then install the scoop firmly with 3M tape after drying.
- APPLICABLE MODELS: The hood air intake protection cover suitable for Subaru WRX 2022 2023 .
- QUALITY MATERIAL: The hood air intake cover is made of high quality stainless steel, not easy to aging, wear-resistant and durable, long service life.
- FUNCTION: The hood air intake protection cover is net design, which can protect the hood air intake, prevent leaves, stones, pieces of paper and other small objects from entering into the air intake, and also can decorate the car, enhance the appearance of the car, is your car looks cooler.
- EASY TO INSTALL: The size of the hood air intake protection cover is customized according to the original car, perfect fit, just install it directly, professional installation is recommended.
- RELIABLE AFTER-SALES SERVICE: If you have any questions about the product/installation problems, receive incorrect/damaged product, or the product does not fit your vehicle, please do not install and contact us, we will answer your questions/refund/exchange the product within 24 hours.
- Fitment: Compatible with Subaru WRX/ WRX STI 2015 2016 2017 2018 2019 2020 2021.
- Material: Plastic, Color: Carbon Fiber Style, Surface Finish: Carbon Fiber Printing.
- Feature: Made of high density ABS plastic, longer lifespan, better aging resistance, strong and beautiful. Make the vehicle offer more personalized, giving your vehicle a more stylish and luxurious glamorous look.
- Function: It provides additional cooling for the engine, promotes air circulation and ensures better ventilation and heat dissipation.
- Package including: Contain a hood scoop with mesh grille, a set of necessary assembly hardware shown in pictures, instructions. Easy to install, only requires bolts and 3M tape. You need to first stick the glue on the hood, and then use 3M tape to install the scoop after drying. At the same time, tighten the screws at the joints to ensure a firm installation.
- 🌿🌿【Compatible】Designed for Subaru WRX STI 2015-2018 / Levorg VM4/VMG 2014-2017, front hood scoop vent decor perfectly match the original car.
- 🌿🌿【Application】Comparison before and after installation, provides a high class and fashion decor style, change the ordinary interior design of the car and add unique colors. It can cover existing scratches and prevent your car from scratch and abrasion.
- 🌿🌿【High Quality】Made of high quality ABS Plastic, strict QC standard test, anti-corrosion and water proof. Has high temperatura resistance. Don't worry about it falling down while driving, improve your diving experience.
- 🌿🌿【Installation Method】1 pieces of a set, 3M tape at the back. Before installation, please keep the surface clean and dry, no sand/dust, remove the adhesive tape. Heat the tape with heat gun or use hair drier instead, and then press it almost 1 minute.
- 🌿🌿【Service】Our target is : 100% customer satisfaction and strive to provide you good shopping experience.If you have any question, Please feel free to contact us.
- GUARANTEED INCREASE IN HORSEPOWER & TORQUE: K&N cold air intake systems provide a less restrictive path for airflow, increasing the volume of cool, oxygen-rich air into your engine an estimated increase up to 7HP and up to 6 ft.lbs. of Torque
- HEAR THE GROWL: K&N’s intake systems allow your engine to breathe and sound as it should- your engine will growl on acceleration and return to quiet once at speed
- DYNO TESTING YOU CAN TRUST: K&N air intake horsepower/torque testing is performed on wheel-based dynamometers and the reports are include with each intake system
- FEATURING K&N’s SIGNATURE, REUSABLE AIR FILTER: Combines 4 layers of pleated, breathable cotton with K&N’s red filter oil to absorb dirt and dust particles, allowing clean air to continue flowing into your engine, only needs cleaning every 100,000 miles under normal highway driving conditions
- DURABLE ALUMINUM INTAKE TUBE & CUSTOM HEAT SHIELD: For a more custom look under the hood, a mandrel-bent and powder coated aluminum intake tube helps increase the volume of airflow to your engine, while the heat shield helps protect intake air from the high temperature of your engine bay
- 50 State C.A.R.B. Compliant
- C.A.R.B E0 # D-370-15
- Aluminum Piping, Mandrel bent
- Corrosion Resistant
- Reusable and Washable High Flow Air Filter
- Compatible with:For 2019 Subaru Forester Bumper Assembly; For 2020 Subaru Forester Bumper Assembly; For 2021 Subaru Forester Bumper Assembly
- Material: Plastic
- Placement on Vehicle: Front
- Quality Manufacturing of the Product Meets or Exceeds Oem Specifications.Bumper Grille Assembly Can Perfect Air Intake and Ventilation, Personalized Products Make Your Car Look More Beautiful.
- Warranty:We provide a one-year warranty.
Last update on 2024-03-07 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.
SEOCONTENT-START
Bulletin Number: 12-305-20; Date: 12/07/20 Page 1 of 2 Continued… CAUTION: VEHICLE SERVICING PERFORMED BY UNTRAINED PERSONS COULD RESULT IN SERIOUS INJURY TO THOSE PERSONS OR TO OTHERS. Subaru Service Bulletins are intended for use by professional technicians ONLY. They are written to inform those technicians of conditions that may occur in some vehicles, or to provide information that could assist in the proper servicing of the vehicle. Properly trained technicians have the equipment, tools, safety instructions, and know-how to do the job correctly and safely. If a condition is described, DO NOT assume that this Service Bulletin applies to your vehicle, or that your vehicle will have that condition. Subaru of America, Inc. is ISO 14001 Compliant ISO 14001 is the international standard for excellence in Environmental Management Systems. Please recycle or dispose of automotive products in a manner that is friendly to our environment and in accordance with all local, state and federal laws and regulations. NUMBER: 12-305-20 DATE: 12/07/2020 APPLICABILITY: 2015-20MY WRX and WRX STI SUBJECT: Front Hood Intake Duct- Design Change INTRODUCTION: This bulletin announces a design change made to the front hood air intake duct used on the models listed above. The new duct utilizes larger holes at the attachment points to facilitate the use of mounting bolts with a larger shoulder (boss) diameter as shown (in green) in the illustrations below. For this reason, the new mounting bolts are not interchangeable and cannot be used with the original style duct. PRODUCTION CHANGE INFORMATION: The new duct and mounting bolts were incorporated into production starting with VIN L9819487. PART INFORMATION: • New Mounting Bolt: 901020030 • New Duct-Inner Front Hood: 57253VA011 SERVICE BULLETIN ATTENTION: GENERAL MANAGER q PARTS MANAGER q CLAIMS PERSONNEL q SERVICE MANAGER q IMPORTANT – All Service Personnel Should Read and Initial in the boxes provided, right. © 2020 Subaru of America, Inc. All rights reserved. Bulletin Number: 12-305-20; Date: 12/07/20 Page 2 of 2 REMINDER: Always order the most up-to-date replacement parts based on the specific VIN being repaired. SERVICE PROCEDURE / INFORMATION: REMINDER: Customer satisfaction and retention starts with performing quality repairs. The service procedures for hood duct replacement remain unchanged. Always refer to the applicable Service Manual and review the full requirements of the repair being performed. Service Manual procedures contain information critical to performing an effective repair the first time, every time. This includes but is not limited to important SAFETY precautions, proper inspection criteria, necessary special tools, required processes and related one-time-use parts needed for a complete and lasting repair. WARRANTY / CLAIM INFORMATION: For vehicles within the Basic New Car Limited Warranty period, this repair may be submitted using the following claim information: Labor Description Labor Operation # Labor Time Fail Code HOOD GRILLE UPPER DUCT R&R A915-182 0.3 XIW-29 IMPORTANT REMINDERS: • SOA strongly discourages the printing and/or local storage of service information as previously released information and electronic publications may be updated at any time. • Always check for any open recalls or campaigns anytime a vehicle is in for servicing. • Always refer to STIS for the latest service information before performing any repairs.
**************************************************************************************************************
SEOCONTENT-END