Side Under Spoiler – 2022 Subaru BRZ STI

“This site contains affiliate links for which OEMDTC may be compensated”

Accessory Installation Guide

2022MY BRZ STI Side Under Spoiler E2610CC000

 

Installation Instructions

 


STI Side Under Spoiler

Installation Manual

 

Genuine part number : E2610CC000

Applicable model : BRZ (ZD),A Type~

 

– This manual describes how to install and handle the STI Side Under Spoiler.

– Read this manual carefully before work and make sure to install it correctly.

 

Precautions

– Install the STI Side Under Spoiler by reading the Installation Manual carefully.

– Handle the STI Side Under Spoiler with care and do not let it fall.

– Do not install or use this product in any way other than described in this manual.

– We do not assume any responsibility for any trouble arising from failure to comply with the instructions in this manual.

– Double-sided tape is used to attach the STI Side Under Spoiler. Attach it with care as once it is attached, it is extremely difficult to remove.

 

Before Work

– When installing this product, park the car on a level ground and apply the parking brake.

– When installing this product, be sure not to damage the car body.

– Before installing this product, wipe off any dirt or oil film from the Spoiler ASSY-Side attachment surface with a soft waste cloth dampened in a neutral detergent. Then, let it dry completely before work.

– The adhesive strength is weakened significantly when the temperature is 15℃ or lower. In this case, use a dryer to warm up the double-sided tape before attachment.(Do not warm up excessively as doing so may result in deformation.)

– Be extremely careful not to let this product get wet by washing, etc. for 24 hours after attaching it. Dosing so may cause the product to come off.

– To protect yourself from burns, make sure to stop the engine and let it cool completely before work

– When jacking up the vehicle, be sure to keep the ground level and a hard place where the jack does not bite, and be sure to support it with a rigid rack before carrying out the work.

 

Remove the Rear tires

1. Refer to the service manual and remove the rear tires from the vehicle.

(1 places each for RH and LH, 2 places in total)

 

Drilling holes in the Spoiler ASSY-Side

1. As shown in Fig. 2, apply a drill to the center of the Spoiler ASSY-Side bottom locator, make pilot holes in the order of 3 mm and 6 mm, and finally make a 9.5 mm hole (2 places for each of RH and LH, 4 places in total)

Before drilling, make a stopper with cloth adhesive tape at a point about 5 mm from the tip of the drill so that the drill does not interfere with it.

 

2. Insert the ② Well Nut into the 9.5 mm hole.

(2 places each for RH and LH, 4 places in total)

 

Degrease the Spoiler ASSY-Side

1. Degrease the shaded area in Fig. 4.

 

Sticking the Sponge

1. As shown in Fig. 5, attach masking tape to a height of 110 mm from the lower end of the Spoiler ASSY-Side to mark it.

 

2. Insert the sponge into the back of the Spoiler ASSY-Side, determine the height position using masking tape as a guide, and attach it so that it does not protrude from the R END of the broken line.

(1 places each for RH and LH, 2 places in total)

 

3. Peel off the attached Masking tape.

 

4. Insert the ⑤ BRKT into the ④ Sponge as shown in Fig. 6.

(1 places each for RH and LH, 2 places in total)

Insert ⑤ BRKT firmly as far as it will go.

 

Installing the STI Side Under Spoiler

1. Peel off the double sided tape release paper of the ① STI Side Under Spoiler by about 30 mm and fix it on the front side with masking tape.

(1 places each for RH and LH, 2 places in total)

Do not remove the release paper more than necessary.

The double-sided tape clings to the peripheral parts, which makes it difficult to position them.

 

2. As shown in Fig. 8, apply ① STI Side Under Spoiler and temporarily fix it with ③ Bolt. Determine the position by aligning the broken line R in the same way as arrow c.

(2 places each for RH and LH, 4 places in total)

 

3. As shown in Fig. 9, fix the ① STI Side Under Spoiler to ⑤ BRKT with ⑥ Screw.

(2 places each for RH and LH, 4 places in total) Reference tightening torque : 1.0 N ・ m (0.1 kgf ・ m).

⑥ Screw cannot be reused because they use screw lock material.

 

4. As shown in Fig. 10, crimp the double-sided tape part while slowly pulling it out in the direction of the arrow so that the paper pattern does not break in the middle.

If the release paper is difficult to pull out, slowly pull it out using radio pliers.

When pulling out the paper pattern, make sure that the Protecter does not turn over.

 

5. Fully re-bond the double-sided tape with 49N or more.

 

Install the Rear tires

1.Refer to the service manual and Install the rear tires on the vehicle.

(1 places each for RH and LH, 2 places in total)

 

This is the end of work.

 


https://techinfo.subaru.com/stis/doc/accInstallGuide/E2610CC000_STI%20Side%20Under%20Spoiler.pdf

https://static.oemdtc.com/AccessoryInstallationGuide/E2610CC000.pdf

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [2.73 MB]

 


 

“This site contains affiliate links for which OEMDTC may be compensated”
SaleBestseller No. 1
KUAFU Side Skirt Rocker Panels Guard Compatible with 2012-2021 Subaru BRZ Toyota 86 Scion FR-S Extension Replacement Spoiler Body Kit Black ABS
  • FITMENT - Our Side Skirts are compatible with 2012-2021 Subaru BRZ; compatible with 2012-2021 Toyota 86; compatible with 2012-2021 Scion FR-S. Please make sure that if your car is compatible with our products.
  • IMPROVED AERODYNAMICS - Side skirts reduce the body's ground clearance above the road, creating less air pressure under the car, improving road-holding and allowing the car to be driven safely at higher speeds.
  • ENHANCE APPEARANCE - The side skirts are also a design element that adds to the sporty feel of the car's design and enhances its visual appeal. Made from ABS for strength and durability.
  • ADDITIONAL PROTECTION - The side skirts are fitted to the sides of the car to provide a degree of protection against the splashing of stones and debris from the road, which can scratch the surface of your car.
  • INSTALLATION & PACKAGE INCLUDED - Screws help hold it in place and 3M tape makes it more securely mounted on your car. You will receive 1 Pair of side skirts and mounting hardware. No instructions.
Bestseller No. 2
Xotic Tech Front Bumper Lip Spoiler + Side Skirt Splitter + Rear Bumper Lip Wrap Splitter Canard,Compatible with Subaru BRZ Impreza WRX STI (Black)
  • Package includes:1 set of Front Bumper Lip Chin Spoiler Guard Body Kits (3pcs) + Side Skirt Splitter (2pcs) + Rear Bumper Lip Wrap Splitter Canard (2pcs)
  • Material:Made of updated durable and sturdy ABS, no deformation in long-term use,waterproof and never fade.
  • Function:Provide an elegant and personalized appearance, provide anti-collision protective experience to your original bumper, protect from scrapes from driveways, speed bumps and curbs, alleviate the damage
  • Compatibility:Perfect compatible with Subaru BRZ Impreza WRX STI,It won't scrape the paint off or damage the original equipment. Enjoy the super cool and exquisite appearance of your car after installing.
  • Note:1.Please measure the position you are going to install the package, and make sure these splitters will fit your vehicle before purchase 2.Professional installation is highly recommended 3.Product may require drilling holes and use the screws to permanently secure.
Bestseller No. 3
Miytsya 2 PCS Rear Bumper Canard Diffuser Splitter Protector Universal Rear Bumper Lip Body Kit Rear Side Skirt Valence Spoiler (Carbon Fiber Black)
  • ★ Exquisite Workmanship: Premium quality ABS carbon fiber material in great finished, light, anti-corrosion, rust resistant and never fade. High temperature resistant, ensures maximum strength and durability for long lasting usage.
  • ★ Function: The rear bumper diffuser can absorb impacts and prevents scratches, smooth and delicate cross-section, effectively protects the bumper from bump damages or scratch when stopping or parking.
  • ★ Fitment: Universal for most of car models, fluid curve surface, only use on rear bumper, gives your car exterior a more luxury and glamorous look in a minutes.
  • ★ Easy to Install: Clean the installation location, it can be mounted on screw or stick with double side adhesive tape. Product may require drilling holes and apply bolts to attach to your bumper.
  • ★ After Sale: If you have any question on use, kindly contact us at any time directly, we will solve the problem for you within 24 hours on weekdays.
Bestseller No. 4
Car Rear Spoiler Roof Lip Kit, Carbon Fiber 3D Rubber Trunk Spoiler Trim Strip Cool Car Decoration, Universal Punch-Free Vehicle Exterior Accessory Sticker (Black)
  • 【Dimensions】:57.75 inches long and 1.45 inches wide. GM Rubber Spoiler is very flexible and cuttable, it fits perfectly in any car trunk or roof. Fits any car, truck, SUV.
  • 【High Quality Material】:The rear spoiler is made of high-quality rubber with a smooth and shiny surface that is smooth and glossy in the sun. It has excellent flexibility while maintaining a degree of hardness for reliability and durability.
  • 【Comprehensive Body Protection】:This spoiler wing can protect multiple parts of your car, such as front and rear bumpers, front and rear lips, side skirts, and tailgate, keeping your car safe from scratches and collisions.It can be bent freely, adjustable according to the curvature, free fit and high fit.
  • 【Wide Applications】:A car rubber spoiler can be installed on the trunk, root wing, or hood of your car, adding a stylish and streamlined appearance. It not only decorates your car but also improves driving stability, fuel efficiency, and ride quality. The linear design enhances the performance of your car's engine and maximizes its overall performance.
  • 【Non Punching Installation】:The roof spoiler is fixed with a strong adhesive bottom. ①Measure the length required for installation and cut off the excess. ② Wipe the car adhesion area clean. ③Remove the protective film from the double-sided adhesive tape. Use a hot air blower to slightly heat the double-sided adhesive tape to make it stick tighter.
SaleBestseller No. 5
AUCELI Car Spoiler Canards Kit, 2 Pcs Universal Car Front Bumper Splitter, Fender Side Vents Stickers Soft Fins Spoiler Kit, Anti-Collision Decoration Strip for Car Body Hood Side Wing (Black)
  • 【Excellent Material】: Our car spoiler canards kit is made of high quality TPU material, exquisite workmanship, fine texture, soft and flexible, perfectly fits the curve of your car. Wear-resistant, not easy to age, can withstand long periods of wind and rain and sun exposure, very durable.
  • 【Vehicle Universal】: The size of the car spoiler is about 9.1 x 1.6 x 4.7 inches, which can be widely used in most vehicles. It is sticker mounted and can be applied anywhere you want, trunk, bumper, doors, and all over the body. You can use it whether it is for SUV, MPV, sedan, or truck.
  • 【Collision Protection】: This sticker can cover scratches well and make the car look like new and more beautiful. Stick it on both wings of the front bumper to protect the body paint and keep the car from being scratched by collisions when passing through narrow places or parking.
  • 【Fashionable and Cool】: You have 2 colors to choose from, black and carbon fiber, they bring dynamics and texture to the car, making it more fashionable and cool. The overall curved design fits the contour of the side wings, the surface is very smooth and refracts a faint bright light in the sunlight, very beautiful.
  • 【Easy to Install】: No other tools are needed. First clean the surface of the car, keep it dry and clean. Then tear off the protective film on the back of the car bumper sticker and stick the sticker on to complete installation. (Tip: In cold weather, use a hot hair dryer to heat properly, paste more firmly.)
Bestseller No. 6
Xotic Tech JDM Rear Bumper Canard Diffuser Splitter Valence Spoiler Fin Lip Trim Universal Fit (Carbon Fiber Pattern) 4.48"x17.63"
  • 🚘Pair of rear bumper lip wrap angle splitters with 6 pieces of mounting screws for both left and right sides.
  • 🚘Made of premium quality ABS material with carbon fiber pattern coating; light, anti-corrosion, rust resistant and never fade.
  • 🚘These lower bumper lip canards deflector will protect your car rear bumper from scratches and small damages, meanwhile, give your vehicle a racing sporty look.
  • 🚘You could drill holes and bolt them on to your car bumper or use double-sided tape to adhere them.
  • 🚘Designed for all cars, off-roads, SUVs, trucks.
Bestseller No. 7
146PCS Auto Body Clips Nylon Bumper Shield Retainer Clip, Fender Flar, Blind Rivet & Rocker Moulding Clips, with Fastener Remover
  • Compatible with Chrysler: 6033082, 6033840; Compatible with Ford: 390018-S for GM; Compatible with GM: 10121502
  • Plastic Rivet Fastener Compatible with Honda 0666-SA0-0030. Compatible with GM 411700
  • Compatible with Ford: N807721-S; Compatible with Chrysler: 6504043
  • Compatible with Chrysler: 6030441; Compatible with Ford: W705589-S300, 388577S; Compatible with GM: 1595864, 1605396
  • Double End X-Mas Tree Retainer Black Clips Cars Boats Trucks Compatible with Auveco A20866.
Bestseller No. 8
Ozukyn Front Bumper Lip Spoiler Side Body Kit Trim Protection Under Chin Spoiler for Subaru WRX STi Sedan 2015 2016~2018 2019 2020 3Pcs Gloss Black Color
  • 👍👍【Fit For】fits for Subaru WRX STi Sedan 2015 2016~2018 2019 2020 (Please check whether this item can fit on your car before purchasing)
  • 👍👍【 High Quality】Made of high quality ABS material .100% brand new and high quality guaranteed . ISO 9001 certification to ensure quality.
  • 👍👍【Advantage】Provide an elegant and personalized appearance, Front bumper guard anti-collision protective, protect from scrapes from driveways, speed bumps and curbs.
  • 👍👍【Easy Installation】Installation can be easily done, no modification required. Note : Package does not come with instructions. Professional installation is always recommended.
  • 👍👍【Intimate Customer Service】If you have any quality problems, please don't hesitate to contact us with e-mail.It is our pleasure to solve any problems for you .
Bestseller No. 9
Jawmoy 6 PCS Car Spoiler, Car Front Bumper Lip Splitter, Carbon Fiber Spoiler, Car Body Auto Anti Collision Strip Decoration, Car Sticker (Glossy Black)
  • Premium Material: Made of soft PVC material, the car spoiler is processed by exquisite workmanship, fine in texture, serviceable and reliable, well fit your car curves, resistant to wear, deformation, breakage and ageing. Meanwhile, it can protect the car body paint and keep the car from being scratched.
  • Perfect Protection: The bumper of the car is easy to scratch. This product is made for bumpers. It is exquisite and stylish. It not only protects the bumper of the car perfectly, but also effectively avoids the scratch of the car. Improve the grade of the car as a perfect decoration.
  • 3 Sizes: The spoilers for cars are in 3 sizes, respectively about 20 x 3.5cm/7.8 x 1.3 inches, 16.5 x 3cm/6.4 x 1.1inches, 13.5 x 2.5cm/5.3x0.9 inches, able to give your car body a sporty and beautiful appearance. The overall arc design is full and round, which realizes the protection of small objects.
  • Easy to Install: There is adhesive on the back of the bumper spoiler, which is very easy to install. Please clean the car before installation, make sure it is dry and dust-free, so that the adhesive will be more viscous. In cold weather, you can use a hot hair dryer to properly heat the adhesive, which will make it easier to stick firmly.
  • Enough to Use: The package contains 6pcs car bumper spoilers, which can meet your modification needs of the car. If you have any question on use, kindly contact us at any time directly, we will solve the problem for you within 24 hours on weekdays.
Bestseller No. 10
Car Front Bumper Lip Splitter, 2.5m/8.2ft Front Lip Spoiler, Self-Adhesive Waterproof Auto Side Skirt Protector Strip, Universal Exterior Soft Rubber Decoration Accessories for Cars (Black)
  • 【Durable and Sturdy Rubber】: High-quality rubber materials, carbon fiber texture surface, smooth and delicate, good flexibility. It adopts scientific design, lightweight foaming process, soft and not easy to deform. This car bumper crash strip fits perfectly into your bumper, is flexible to use, has excellent wear resistance, protects the car and reduces damage.
  • 【Soft Feeling】: Car front lip anti-collision strip is suitable for most cars, the size is 98.4 inches * 2.6 inches. You can glue it to the front and rear bumpers or side skirts of the car. This premium car bumper strip will not be affected by wet or cold weather, and has good scratch and decorative features. It makes the car look better as well as protecting it from scrapes.
  • 【DIY Easy to Install】: It can be bent and folded freely according to the shape and curvature of the car, and the shape is quickly restored. Clean the installation position, tear off the protective film on the back of the adhesive strip, and then press it for a while. If the curvature is large, you can cut out several triangles on the strip to fit your car. If you are worried about it falling off during driving, you can reinforce it with screws.
  • 【Carbon Fiber Decoration】: This personalized car sticker can be applied anywhere you want to make your car look more sporty, adding style and personality. Protect your car from collision, prevent the front bumper against lane scraping, speed bumps and stones on the side of the road. With this front bumper lip splitter you can have a safe driving.
  • 【Universal Fit】: This car crash strip is easy to bend, cut and fold. It can be attached to the front and rear bumpers, side skirts, rear wing and so on. The length can be adjusted to suit your car. It is suitable for vehicles other than SUVs, vans. It can withstand shocks and collisions during driving. If you have any questions, please feel free to let us know.

Last update on 2024-03-26 / Affiliate links / Images from Amazon Product Advertising API

This product presentation was made with AAWP plugin.

 


Leave a Comment

Share to...