| “This site contains affiliate links for which OEMDTC may be compensated” |
Accessory Installation Guide
| 2022MY BRZ Exterior Graphics – Side | J121SCC000 |
Installation Instructions
PART NUMBER: J121SCC000
INSTALLATION INSTRUCTIONS
DESCRIPTION:
Exterior Graphics – Side
KIT CONTENTS:
1. Exterior Graphics – Side (2).
2. Squeegee (1).
3. Alcohol Wipes (2).
TOOLS REQUIRED:
Soft lint-free
Microfiber Cloth
32 ounce Spray Bottle
- Water
- 2ml Baby Shampoo
PREPARATION – BEFORE INSTALLATION:
1. This product should be installed with proper installation tools.
2. Install this product while observing all warnings and precautions stated in this instruction booklet.
3. VERY IMPORTANT: Thoroughly wash vehicle with Soap and Water.
4. Parts storage should be flat at room temperature and in a clean dry place. Care should be taken to avoid a dusty environment.
Notes to the Installer
1. Read the entire installation instructions prior to beginning the installation of the accessory.
2. Ensure that the vehicle is properly protected in the area that the accessory is to be installed.
3. To prevent vehicle damage, never place tools on top of painted surfaces, seats, dash pad, console or floor carpet / mat.
4. Always wear appropriate safety gear to include gloves and eye protection when required.
1
Alcohol
Thoroughly wash vehicle with a soft lint-free cloth. Wipe the panel where the Exterior Graphic will be installed with alcohol wipes.
Allow the area to dry completely.
2
Dry Fit
Align the Exterior Graphic into position using the handling tabs, door notches and panel edges as references.
3
Separate Liner
Remove liner from Exterior Graphic as shown. To prevent contamination, limit touching adhesive side of the Exterior Graphic by using handling tabs.
4
Spray Vehicle / Adhesive of Exterior Graphic
Spray the adhesive side of the Exterior Graphic with the soap and water solution. Then Spraying the vehicle surface where the Exterior Graphic will be installed.
5
Exterior Graphic Placement
While using the handling tabs align the Exterior Graphic into position. This allows the part to float on the surface until proper fit is achieved.
6
Spray Exterior Graphic Premask
Spray the top surface of the premask with the soap and water solution. This makes it possible for the squeegee to slide easily across the surface.
7
Squeegee Exterior Graphic
Use caution not to scratch the paint surface with the squeegee.
Using smooth even overlapping strokes squeegee the Exterior Graphic into position.
8
Squeegee Exterior Graphic
Use caution not to scratch the paint surface with the squeegee.
Working from the center out ensure each piece of the Exterior Graphic has been securely adhered to the vehicle surface.
9
Remove Premask
Carefully remove the premask from the Exterior Graphic by slowly lifting and pulling backward at an 180º angle as shown.
10
Inspect Exterior Graphic
If bubbles are present after premask carrier removal, wrap a towel around the squeegee and carefully attempt to push the bubble to the side of the Exterior Graphic. If the bubble cannot be moved, use a sewing needle to pierce the bubble and press the remaining solution from beneath the Exterior Graphic.
*(Repeat Steps 1-10 for the opposite side of vehicle.)
Care and Cleaning
Items to be Checked
After an Exterior Graphic installation has been completed, do not high pressure wash the vehicle for 72 hours.
Visual Check
Items to be Checked
Make sure all edges are firmly adhered.
ISSUE 00
DATE 4/27/21
J121SCC000
2022MY BRZ Exterior Graphics – Side
https://static.oemdtc.com/AccessoryInstallationGuide/J121SCC000.pdf
Loading...
Reload document 
Open in new tab
- 3-in-1 Ceramic formula that REPAIRS fine swirls and scratches, SEALS in protection giving a wet shine finish without the wax and actively REPELS water with the durable Ceramic Technology.
- The innovative Ceramic Technology and durability of a Sealant extends duration of water-beading and protection against water pooling and water damage up to one year*.
- Now with Ceramic Technology for more water beading and protection, Nu Finish The Once A Year Polish & Sealant still contains absolutely no wax.
- Our formula brings shine back to your paint, polishes chrome, and helps to remove fine swirls and scratches in just one amazing formula.
- Polishing power helps remove minor scratches, rejuvenates paint shine and polishes chrome.
- EXCEPTIONAL RESULTS: Advanced technology formula provides a deep gloss and rich, swirl-free results
- NO MORE SWIRLS: Permanently removes swirls and light defects from all paint
- STUNNING SHINE: Produces deep reflections and high gloss
- EASY TO USE: Smooth buffing feel, easy wipe-off, and fast clean-up
- MULTIPLE WAYS TO APPLY: Formulated for use by Hand, DA Polisher, or Rotary Buffer
- Nu Finish Liquid Car Polish keeps your car exterior looking new with only one application per year.Fit Type: Universal
- Delivers impressive shine and protection without rubbing or buffing
- As the only polish available with no wax, the Nu Finish formula is specifically made to protect your car’s paint and clear-coat finish
- Perfect for use on cars, fiberglass boats, RVs, and even chrome surfaces
- Apply polish with a damp cloth, let dry to a haze, and wipe off
- REMOVE PAINT DEFECTS: The ultimate product for removing oxidation, scratches, water spots, and blemishes without scratching
- BEST CAR SCRATCH REMOVER: Cuts as fast as harsh abrasives restoring surface clarity without scratching or swirling
- SAVES TIME: The clear coat safe formula dramatically reduces the time and effort to restore abused or neglected paint finishes
- STUNNING FINISH: Exclusive micro-abrasive technology leaves a "like new" finish and adds gloss in one easy step
- SAFE FOR CLEAR COAT: Safe and effective on clear coat and single stage paints, and can be applied by hand or dual action polisher like Meguiar's MT300 Dual Action Polisher
- EASY-TO-USE ONE STEP POLISH! - P4 Precision Paint Perfection Polish is the easy-to-use one step polish that removes fine swirls, scratches, towel marks, and corrects 2000 grit and finer sanding marks while leaving virtually no dusting or residue behind! .Fit Type: Universal Fit
- SAFE FOR ALL PAINTS! - Ultra-fine abrasives used in P4 are specially developed for all paints including ceramic coated vehicles to remove microscopic amounts of clear coat quickly and leave paint incredibly glossy, shiny, and haze-free!
- WORKS GREAT ON CERAMIC COATINGS! - P4 works great on ceramic coated cars to remove minor imperfections while maintaining the integrity of your coating to produce deep, rich reflections without damaging your protection!
- SHOW CAR SHINE & GLOSS! - Chemical Guys P4 gently removes fine swirls and scratches to deliver a truly perfect finish with a deep gloss and mirror-like finish as the final step in your polish! For even more comprehensive results, first apply C4 Clear Cut Correction Compound!
- PERFECT PREP FOR CERAMIC, SEALANT, AND WAX! - Prepping your car with P4 Polish ensures that your wax, sealant, or ceramic coating makes contact with a totally bare surface, maximizing coating adhesion and durability! Get a deep gloss and shine in no time!
- Heavy duty paste that cleans dull, oxidized finishes
- Quickly and easily penetrates through the oxidized surface to remove scratches, blemishes and stubborn stains
- Restores faded finishes
- Recommended for rubbing down between coats of newly sprayed lacquer and acrylic car finishes
- Easy to use formula
- DEFECT REMOVAL: Great for removing scratches, defects, acid rain and severe swirls/holograms
- ULTRA-FAST COMPOUNDING: Ultra-fast cutting removes 1200 grit or finer sanding marks
- SUPERIOR FINISH: Exclusive super micro-abrasive technology leaves best-in-class finish
- CLEAR COAT SAFE: Safe and effective on all glossy paint finishes including clear coats
- VERSATILE USE: Formulated for use by hand, dual action polisher or rotary buffer, and is body shop safe. Also available in 32 oz and 1 gallon sizes
- UNSURPASSED SLICKNESS – You simply have to touch it to believe how slick this finish is
- MAXIMUM GLOSS AND SHINE – Hands down the highest level of gloss and shine you will ever experience; Achieve mirror-like results in a simple application, right in your own driveway
- EXTREMELY HYDROPHOBIC – Cerakote's true ceramic technology repels water, road grime, mud and dirt making your car stay cleaner, longer!
- QUICK AND EASY TO APPLY - Simply wash and dry your vehicle as you normally would; Then evenly spray a light coat directly to a panel or small area of your vehicle;, then, just lightly buff the coating to an incredible shine! It really doesn't get any easier than this!
- CORRECT & PROTECT … 3D Speed is a premium all in one clear coat car polish & wax all in one bottle!
- BRING YOUR PAINT BACK TO LIFE … 3D Speed is an excellent scratch and swirl remover polish and sealant that deliver minor paint correction for small or large surface areas! Please note: Our products will not remove deep scratches or correct areas where paint may be missing.
- DEPTH AND GLOSS IN ONE … Restore your paint's color, depth and gloss while also adding a long lasting wax layer protection to the surface!
- EASY APPLICATION … You can easily apply 3D Speed by hand for smaller surface areas or with a polisher or buffer for larger areas with more imperfections.
- PROUDLY MADE IN THE USA ... We've been researching and creating exterior and interior car care products for over 25 years now. A quarter of a century of giving our customers uncompromising quality. Go ahead, experience a car polish and wax that's tried and trusted. Date on bottles reflect manufactured dates, not expiry dates.
- Advanced Formula 3-in-1. Our fortify quick coat is your all-in-one ceramic coating hydrophobic spray. Shine Armor Fortify Quick Coat ceramic car wax provides a waterless wash, coat, and shine, all-in-one convenient product.
- No Streaking, Smearing Or Scratching. Shine Armor Fortify Quick Coat premium formula ceramic car coating is a gentle and effective car polish for any vehicle! Get a clean, shiny finish without hurting your car's paint.
- Cuts Dirt, Grime & Grease. Our Quick Coat ceramic wax car sealant eliminates dirt, grime & grease instantly! Our signature 3-in-1 formula gives you a waterless car wash, coat and shine for a clean, showcase look.
- Safe For All Surfaces. Use this car wax spray-on automobiles, boats, motorbikes, RVs, four-wheelers and more! This spray wax is the perfect blend of surfactants and SiO2 ceramic-coating science.
- Superior Products. This means superior shine for your cars! Our ceramic quick coat also works as a sealer to give your vehicle a clear shield of protection while also providing a beautiful gloss. Our ceramic coat is the best hydrophobic car spray available!
Last update on 2024-03-31 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.
SEOCONTENT-START
ALCOHOL WIPE 1. Exterior Graphics – LH Side + RH Side 2. Squeegee (1) 3. Alcohol Wipes (2). Denotes instructional steps necessary to complete the process. Denotes quality processes to be checked prior to moving to the next step. Denotes safety equipment required to be used such as a mask, goggles, rubber gloves, and hearing protection. Denotes cautions to be taken to avoid physical injury or electronic component damage. Denotes warnings that may lead to serious physical injury or vehicle damage. Denotes specific tools that are necessary to complete the step. Denotes cautions to be taken to avoid vehicle and component damage. Mask Goggles Rubber Gloves Hearing Protection SUBARU OF AMERICA PAGE 1 / 4 ISSUE DATE 00 INSTALLATION INSTRUCTIONS PART NUMBER: J121SCC000 DESCRIPTION: Exterior Graphics – Side KIT CONTENTS: TOOLS REQUIRED: MEANING OF CHARACTERS: DESCRIPTION Exterior Graphics – Side Soft lint-free Microfiber Cloth 1. Exterior Graphics – Side (2). 2. Squeegee (1). 3. Alcohol Wipes (2). ALCOHOL WIPE Alcohol Soap & Water • Water • 2ml Baby Shampoo 32 ounce Spray Bottle 4/27/21 PREPARATION – BEFORE INSTALLATION: SUBARU OF AMERICA PAGE 2 / 4 ISSUE DATE 00 Remove liner from Exterior Graphic as shown. To prevent contamination, limit touching adhesive side of the Exterior Graphic by using handling tabs. 2 3 4 Notes to the Installer 1. Read the entire installation instructions prior to beginning the installation of the accessory. 2. Ensure that the vehicle is properly protected in the area that the accessory is to be installed. 3. To prevent vehicle damage, never place tools on top of painted surfaces, seats, dash pad, console or floor carpet / mat. 4. Always wear appropriate safety gear to include gloves and eye protection when required. 1. This product should be installed with proper installation tools. 2. Install this product while observing all warnings and precautions stated in this instruction booklet. 3. VERY IMPORTANT: Thoroughly wash vehicle with Soap and Water. 4. Parts storage should be flat at room temperature and in a clean dry place. Care should be taken to avoid a dusty environment. Dry Fit Thoroughly wash vehicle with a soft lint-free cloth. Wipe the panel where the Exterior Graphic will be installed with alcohol wipes. Allow the area to dry completely. 1 Alcohol Separate Liner Spray Vehicle / Adhesive of Exterior Graphic Align the Exterior Graphic into position using the handling tabs, door notches and panel edges as references. DESCRIPTION Exterior Graphics – Side Exterior Graphics – Side Spray the adhesive side of the Exterior Graphic with the soap and water solution. Then Spraying the vehicle surface where the Exterior Graphic will be installed. Exterior Graphic Liner Premask Premask / Handling Tab Exterior Graphic Liner WATER SOA & P WATER SOAP & 4/27/21 *(Repeat Steps 1-10 for the opposite side of vehicle.) SUBARU OF AMERICA PAGE 3 / 4 ISSUE DATE 00 Use caution not to scratch the paint surface with the squeegee. 6 7 Spray Exterior Graphic Premask While using the handling tabs align the Exterior Graphic into position.This allows the part to float on the surface until proper fit is achieved. Using smooth even overlapping strokes squeegee the Exterior Graphic into position. Working from the center out ensure each piece of the Exterior Graphic has been securely adhered to the vehicle surface. 5 Exterior Graphic Placement Squeegee Exterior Graphic Spray the top surface of the premask with the soap and water solution. This makes it possible for the squeegee to slide easily across the surface. DESCRIPTION Exterior Graphics – Side Use caution not to scratch the paint surface with the squeegee. 8 Squeegee Exterior Graphic 9 Remove Premask Carefully remove the premask from the Exterior Graphic by slowly lifting and pulling backward at an 180º angle as shown. 10 Inspect Exterior Graphic If bubbles are present after premask carrier removal, wrap a towel around the squeegee and carefully attempt to push the bubble to the side of the Exterior Graphic. If the bubble cannot be moved, use a sewing needle to pierce the bubble and press the remaining solution from beneath the Exterior Graphic. Exterior Graphic Premask 4/27/21 WATE S R OAP & Results of the Check Care and Cleaning Items to be Checked Results of the Check Visual Check Items to be Checked After an Exterior Graphic installation has been completed, do not high pressure wash the vehicle for 72 hours. Make sure all edges are firmly adhered. SUBARU OF AMERICA ISSUE DATE PAGE 00 DESCRIPTION Exterior Graphics – Side 4/27/21 4 / 4 ALCOHOL WIPE 1. Graphique extérieur – LH Côté + RH Côté 2. Racloir (1) 3. Lingettes Alcoolisées (2). SUBARU OF AMERICA PAGE 1 / 4 ISSUE DATE 00 INSTRUCTIONS D’INSTALLATION DESCRIPTION: Graphique Extérieur – Côté 1. Graphique extérieur – Côté (2). 2. Racloir (1) 3. Lingettes Alcoolisées (2). LINGETTE ALCOOLISÉE • L’eau 4/27/21 NUMÉRO DE PIÈCE :J121SCC000 OUTILS REQUIS: Linge en microfibre doux et non pelucheux • 2 ml de shampooing pour bébé Flacon pulvérisateur de 946 ml (32 oz) d’alcool shampoo & d’eau SIGNIFICATION DES SYMBOLES: Indique la marche à suivre pour compléter le processus. Indique les vérifications de qualité à effectuer avant de passer à la prochaine étape. Indique l’équipement de sécurité requis et devant être utilisé, comme un masque, des lunettes de sécurité, des gants en caoutchouc et des dispositifs de protection antibruit. Indique les précautions à prendre pour éviter les blessures ou les dommages aux composants électroniques. Indique les avertissements de possibilité de blessure grave ou de dommages au véhicule. Indique les outils nécessaires pour compléter une étape. Indique les précautions à prendre pour éviter les dommages au véhicule et aux composants. Masque Lunettes de sécurité Gants en caoutchouc Dispositif de protection antibruit DESCRIPTION Graphique Extérieur – Côté CONTENU DE LA TROUSSE : SUBARU OF AMERICA PAGE 2 / 4 ISSUE DATE 00 2 3 4 1. Ce produit doit être installé avec les outils d’installation adéquats. 2. Installez ce produit tout en respectant toutes les mises en garde et précautions signalées dans ce livret d’instructions. 3. TRÈS IMPORTANT : Bien laver le véhicule avec du savon et de l’eau. 4.Les pièces doivent être entreposées à plat et à température ambiante dans un endroit propre et sec. Il faut veiller à éviter tout environnement poussiéreux. 1 Alcool Ajustement à sec Retrait de la pellicule protectrice Vaporisation du véhicule / du côté adhésif du graphique extérieur DESCRIPTION Graphique Extérieur – Côté Graphique Extérieur – Côté Prémasque / Languette de manipulation Prémasque / Languette de manipulation Graphique extérieur Graphique extérieur Pellicule protectrice 4/27/21 Laver soigneusement le véhicule avec un linge doux et non pelucheux. Essuyer le panneau à l’endroit où le graphique extérieur sera posé à l’aide de lingettes imbibées d’alcool. Laisser la surface sécher complètement. Aligner le graphique extérieur en position en utilisant les languettes de manipulation, les encoches de porte et les bords du panneau comme références. Retirer la pellicule protectrice du graphique extérieur, comme illustré. Pour éviter toute contamination, limiter les contacts avec le côté adhésif du graphique extérieur en utilisant les languettes de manipulation. Vaporiser le côté adhésif du graphique extérieur avec la solution d’eau savonneuse. Vaporiser ensuite la surface du véhicule à l’endroit où le graphique extérieur sera posé. PRÉPARATION – AVANT L’INSTALLATION: 1. Lisez l’ensemble des instructions d’installation avant de commencer l’installation de l’accessoire. 2. Assurez-vous que la zone du véhicule est bien protégée là où l’accessoire doit être installé. 3. Pour éviter tout dommage au véhicule, ne jamais poser d’outils sur les surfaces peintes, les sièges, le dessus du tableau de bord, la console ou les tapis de sol. 4. Portez toujours les équipements de protection appropriés, y compris des gants et des lunettes de protection pour les yeux au besoin. Remarques à l’intention de l’installateur D’EAU SAVON & D’EAU SAVO & N *(Répéter les étapes 1 à 10 sur le côté opposé du véhicule.) SUBARU OF AMERICA PAGE 3 / 4 ISSUE DATE 00 Attention à ne pas rayer la surface de la peinture avec le racloir. 6 7 5 Positionnement du graphique extérieur Vaporisation du prémasque du graphique extérieur Utilisation du racloir sur le graphique extérieur Attention à ne pas rayer la surface de la peinture avec le racloir. 8 Utilisation du racloir sur le graphique extérieur 9 Retrait du prémasque 10 Inspection du graphique extérieur Si des bulles sont présentes après le retrait du prémasque, envelopper le racloir d’une serviette et tenter soigneusement de pousser la bulle sur le côté du graphique extérieur. S’il est impossible de déplacer la bulle, utiliser une aiguille à coudre pour percer la bulle et extraire la solution restante se trouvant sous le graphique extérieur. 4/27/21 En exerçant une pression ferme et uniforme et en effectuant des mouvements qui se chevauchent, passer le racloir sur le graphique extérieur afin de le positionner. En travaillant du centre vers l’extérieur, s’assurer que chaque partie du graphique extérieur est bien collée à la surface du véhicule. Retirer délicatement le prémasque du graphique extérieur en le soulevant lentement puis en le tirant vers l’arrière à un angle de 180°, comme illustré. Vaporiser la surface supérieure du prémasque avec la solution d’eau savonneuse. Cela permet au racloir de glisser facilement sur la surface. Aligner le graphique extérieur en position en utilisant les languettes de manipulation. Cela permet à la pièce de glisser sur la surface jusqu’à ce qu’elle soit correctement positionnée. Graphique extérieur Pellicule protectrice DESCRIPTION Graphique Extérieur – Côté D’EAU SAVON & Résultats de la vérification Nettoyage Et Entretien Éléments à vérifier Éléments à vérifier Résultats de la vérification Vérification Visuelle Vérifier que tous les bords sont bien collés. SUBARU OF AMERICA ISSUE DATE PAGE 00 4/27/21 4 / 4 Une fois l’installation d’un graphique extérieur terminée, ne pas laver le véhicule à haute pression pendant 72 heures. DESCRIPTION Graphique Extérieur – Côté
**************************************************************************************************************
SEOCONTENT-END