| “This site contains affiliate links for which OEMDTC may be compensated” |
NUMBER: 16-99-16
DATE: 02/29/16
| APPLICABILITY: | 2015-16MY Legacy and Outback 2.5L Models |
| SUBJECT: | TCM Reprogramming for RPM Flare and CruiseControl Operation |
INTRODUCTION
This bulletin announces availability of reprogramming files to optimize transmission control module (TCM) operation and address the following customer concerns:
- Engine RPM “flare” (sharp RPM increase when CVT “downshifts”) when using cruise control on uphill grades
- Cancellation of cruise control as a result of rpm flare (driver must reset desired vehicle speed).
This new logic changes the cruise control system operation to avoid unexpected cancellation.
PRODUCTION CHANGE INFORMATION:
This new logic was incorporated into vehicle production starting with the following VINs:
PACK FILE APPLICABILITY:
| MODEL | PAK FILE NAME | NEW TCM PART NUMBER |
OLD TCM PART NUMBERS |
DECRYPTION KEYWORD | NEW TCM CID NUMBER |
|---|---|---|---|---|---|
| 2015MY Legacy | 30919AD322.pak | 30919AD322 | 30919AD320 30919AD321 |
AC016EC2 | F4F20081 |
| 2015MY Outback | 30919AD332.pak | 30919AD332 | 30919AD330 30919AD331 |
7B8A7BF1 | F4F24081 |
| 2016MY Legacy | 30919AF031.pak | 30919AF031 | 30919AF030 | E1BDFCCA | E5F20080 |
| 2016MY Outback | 30919AF041.pak | 30919AF041 | 30919AF040 | 6B7EF5D6 | E5F24080 |
SERVICE PROCEDURE / INFORMATION
NOTES:
SOA now highly recommends connecting the Midtronics GR8 Diagnostic Battery Charger to the vehicle and utilizing the Power Supply Mode feature anytime a vehicle control module is being reprogrammed. Once the GR8 is connected to the vehicle, as long as the battery is fully charged, it takes less than 3 minutes to boot-up the charger, select the Power Supply Mode, and have the battery voltage stabilized and ready for reprogramming.
VERY IMPORTANT: This information is applicable to the Midtronics GR8 Diagnostic Battery Charger ONLY. It does not apply to any other brand / type of “generic” battery charger 
whatsoever. ONLY the GR8 and its Power Supply Mode feature has been tested and approved by Subaru of America, Inc. (SOA).
- If the GR8 indicates the vehicle’s battery must be charged, charge the battery using the GR8 before proceeding to reprogram the vehicle while using the Power Supply Mode.
- Control module failures as a result of battery discharge during reprogramming are not a matter for warranty. Should any DTCs reset after the reprogramming update is performed, diagnose per the procedure outlined in the applicable Service Manual.
WARRANTY / CLAIM INFORMATION
For vehicles within the Basic New Car Limited or Powertrain Warranty period or covered by a Subaru Added Security Powertrain, Classic or Gold plan, this repair may be submitted using the following claim information:
| LABOR DESCRIPTION | LABOR OPERATION # |
LABOR TIME |
FAIL CODE |
|---|---|---|---|
| TCM Reprogramming |
A860-737 | MJZ-48 | 0.4 |
IMPORTANT: The NEW Calibration Identification number (CID) for any newly-installed programming (as confirmed from the actual control module AFTER installation) MUST be noted on the repair order as this information is required for claim submission.
NOTE: The pack file listings provided in this bulletin are the latest available at the time of publishing. Updates are often released thereafter without revision to the original bulletin. For this reason, it is critical to always have the latest version of Select Monitor software installed on your system. You can confirm if a later version is available by entering the CID listed in this bulletin into FlashWrite. If a newer CID is shown as available in FlashWrite, reprogram using that file.
IMPORTANT REMINDERS:
- SOA strongly discourages the printing and/or local storage of service information as previously released information and electronic publications may be updated at any time.
- Always check for any open recalls or campaigns anytime a vehicle is in for servicing.
- Always refer to STIS for the latest service information before performing any repairs.
J2534 Reprogramming
Subaru reprogramming files using a generic (non-OEM) SAEJ2534 pass-thru vehicle programming device are available by contacting Service Technical Information Company toll free at 1-866-428-2278. The cost for the CD-ROM with all reprogramming files is $75.00 plus S/H and applicable state tax. Files will be updated four (4) times per year, in CD-ROM format, with all available reprogramming service information at the same above offered cost. Authorized Subaru Dealers are provided the same reprogramming information.
Before purchasing, the reprogramming details can be found in the following Reprogramming J-2534 Files chart. Click the link to view the PDF chart.
Subaru J2534 Reprogramming software meets the latest available J2534-1 specification. Our Reprogramming J2534 Files chart does not specify the Calibration Identification Number (CID); however, this information is included in our offered CD-Rom.
Note: The ECM or TCM being reprogrammed may already contain some or all of the reprogramming files listed in the Reprogramming J2534 Files chart shown by release date. It is possible to damage the vehicles ECM/TCM during the reprogramming event. Once the reprogramming process has started, it is recommended not to interrupt the process until the event is completed. If you experience any problems, please contact your scan tool maker for further instructions.
Are all pre-2004MY Subaru vehicles compatible with J2534?
No. Subaru has no reprogramming capability for model years 1996-1998. Starting with our 1999 model year, please see our Reprogramming Pre-J2534 Files chart for affected model reprogramming information.
Both pre-J2534 reprogramming and J2534 pass thru reprogramming files are included in the offered HDS kit software for aftermarket service provider application.
