“This site contains affiliate links for which OEMDTC may be compensated” |
Accessory Installation Guide
2022MY Forester Auto Dimming Mirror | H501SSJ000 |
Installation instructions
Instructions d’installatiion
Part number:
Numéro de piéce:
H501SSJ000
Description: Auto dimming mirror
Description: Tetroviseur antieblouissement
1
Disconnect battery. If equipped disconnect eyelet cable only.
Déconnectez la batterie. Si elle en est équipée, déconnectez le câble de l’oeillet uniquement.
2
Remove original mirror by pulling on tab away from windshield and sliding mirror up and off the windshield mirror mount.
Retirez le rétroviseur d’origine en tirant sur la languette pour l’éloigner du pare-brise et en faisant glisser le rétroviseur vers le haut pour le sortir du support
3
1 – Remove cover with trim tool starting from the front.
1 – Retirez le couvercle à l’aide de l’outil pour garniture en commençant par l’avant.
4
1 – For vehicles without Eyesight remove two screws.
1 – Pour les véhicules sans Eyesight, retirer les deux vis.
5
Gently pull down cover to release clips.
Tirez doucement le couvercle vers le bas pour libérer les attaches.
6
Disconnect three harnesses from maplight/cover assembly.
Débrancher les trois faisceaux de la lampe de lecture ou du couvercle.
7
Install auto-dimming mirror by sliding mirror down onto the base. Tighten set screw with T-20 Torx bit to 13.3 – 17.7 in-lbs.
Installer le rétroviseur intérieur à atténuation automatique en le faisant glisser vers le bas sur la base. Serrer la vis de pression avec un embout Torx T-20 à 13,3 à 17,7 po-lb
8
Route wire harness through Eyesight cover opening.
Faire passer le faisceau de câblage à travers l’ouverture du couvercle Eyesight.
9
Route harness between sheet metal and plastic bracket.
Faire passer le faisceau entre la tôlerie et le support en plastique.
10
Connect mirror harness to pre-arranged vehicle harness.
Brancher le faisceau du rétroviseur au faisceau du véhicule préinstallé.
11
Connect mirror harness to mirror.
Brancher le faisceau du rétroviseur au rétroviseur.
12
Install mirror harness cover.
Poser le couvercle du faisceau de rétroviseur.
13
Secure wire harness with wire tie.
Fixer le faisceau de câblage avec une attache autobloquante.
14
Secure wire harness to sheet metal using foam tape to ensure wire harness does not rest on Eyesight module.
Fixer le faisceau de câblage à la tôlerie à l’aide de ruban mousse pour s’assurer qu’il ne repose pas sur le module Eyesight.
15
Reinstall map light/cover assembly.
Réinstaller la lampe de lecture ou le couvercle.
16
Reconnect battery. If equipped reconnect eyelet cable. Tighten bolt to 66 in-lbs.
Rebranchez la batterie. Si elle en est équipée, rebranchez le câble de l’oeillet. Serrez les boulons à 66 po-lb.
17
Using dark cloth or cardboard, completely cover forward-looking sensor.
Avec un linge sombre ou un carton, couvrez complètement le capteur pointé vers l’avant.
18
To calibrate compass reference mirror user guide.
Pour étalonne la boussole, reportez-vous au manuel du rétroviseur.
ISSUE
A
DATE
10/22/2021
H501SSJ000
2022MY Forester Auto Dimming Mirror
https://techinfo.subaru.com/stis/doc/accInstallGuide/H501SSJ000.pdf
https://static.oemdtc.com/AccessoryInstallationGuide/H501SSJ000.pdf
- Car Auto Dimming Rear View Mirror, Germid auto-dimming rearview mirror utilizes 3rd generation electrochromic material and dual photoelectric sensors to automatically adjust the dimming level and eliminate glare, giving you a safer and more comfortable driving experience.
- Original Factory Style & Universal Fitness, With its sleek and modern design, our mirror complements your vehicle's original factory style. Its replaceable rearview mirror bracket with double-jointed ball provides adjustable visibility and universal fit for most car models.
- High Quality Material-4.0 mm Thickness Glass, Germid mirror is made with factory OEM quality 4.0 mm glass, which meets vehicle safety standards and offers high reflectance for a clear and crisp image.
- Easy for Installation, Included with the mirror is a Door Clip Panel Trim Removal Tool, making it easy to hide the wire during installation. Moreover, our patent replaceable rearview mirror bracket allows for easy installation and replacement.
- These mirrors eliminate the glare of headlights behind you for safer nighttime
- Mirror automatically dims as it detects glare
- The brighter the glare, the more the mirror dims
- Dimensions - 12 x 6.5 x 4.75 in.
- Gentex Auto-Dimming Rear View Mirrors
- Auto-Dimming
- Homelink integration
- Frameless Auto Dimming Mirror
- Wiring harness is included.
- Wire cover included
- International products have separate terms, are sold from abroad and may differ from local products, including fit, age ratings, and language of product, labeling or instructions.
- UPGRADED STUNNING 4K UHD - With the front cam's resolution upgrading to 2160p from 1296p as of December 1, 2022, this G840S rear view mirror camera can record you 4K front images and 1080p rear images. The full rear display is 1.5 times larger than an ordinary rearview mirror, which has significantly reduced rearview blind spots.
- 12'' LARGER SCREEN & BROAD VIEW - Upgraded from most rearview mirror cameras, WOLFBOX 170° front, and 140° rear lens provide an ultra-wide view, minimizing the blind spots for safe driving/reversing. With the smart screen split function, you can observe a dual-lens display simultaneously. With a 2.5D curved screen, the body is more smooth and more suitable for the curvature of the human retina. Its OEM looking makes the mirror camera perfectly integrate with the existing mirror.
- CLEAR IMAGE & ENHANCED NIGHT VISION - With a built-in high-quality chip, the WOLFBOX mirror camera records 4K front and 1080P rear videos. The mirror dash camera applied an upgraded low-reflectivity LCD to reduce reflection during the day. With incorporated WDR&HDR tech balancing the lights, and the help of a starvis sensor and 6-glass lens to capture higher quality images, driving at night or in any challenging lighting situations should be more effortless.
- GPS TRACKING ALL THE TIME - With the external GPS antenna plugged in, you can view the GPS info on display while on the wheel. Playback recorded videos on GPS Player, not only can you check the double channel videos on one screen, but also accurately trace back all the GPS metrics.
- 24H PRECISE PARKING MONITOR - Aside from loop recording for safe driving, your car will still be in safe hands after being parked. The time-lapse mode is there to monitor at very low fps which saves power and capacity while having everything recorded.
- ??High Quality Material??100% high quality material.The Car Rearview Mirror made of high quality and durable material.Good quality not only can provide a safer guarantee for your life,but also good materials can increase product life.
- ??After-sales Guarantee??If you have any questions about the product,or you encounter problems with your use,you can contact us directly.We will provide you with a solution in good time.No need worry about after-sale services.
- ??High Quality Material??100% high quality material.The Car Rearview Mirror made of high quality and durable material.Good quality not only can provide a safer guarantee for your life,but also good materials can increase product life.
- ??High Quality Material??100% high quality material.The Car Rearview Mirror made of high quality and durable material.Good quality not only can provide a safer guarantee for your life,but also good materials can increase product life.
- ??High Quality Material??100% high quality material.The Car Rearview Mirror made of high quality and durable material.Good quality not only can provide a safer guarantee for your life,but also good materials can increase product life.
- Auto-Dimming
- Integrated Compass
- Homelink integration
- Back Lit Buttons
- Automotive auto dimming rearview mirror
- Make nightime driving safer with auto-dimming
- PathPoint compass system
- Outside temperature display
- Complete kit includes mirror, temperature sensor, wire harness
Last update on 2024-04-15 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.
SEOCONTENT-START
Installation instructions Instructions d’installatiion Auto dimming mirror Tetroviseur antieblouissement Tools required Outils requis Part number: Numéro de piéce: Kit contents Contenu de la trousse H501SSJ000 Description: Auto dimming mirror Description: Tetroviseur antieblouissement ISSUE A PAGE 1/6 DATE 10/22/2021 SUBARU OF AMERICA A T-20 Panel removal tool Outil de dépose du panneau Forester Vehicle: Véhicule: 10 mm 12 mm 8 mm B C D E Wire harness cover Couvre-faisceau de câblage Wire harness Faisceau de câblage Wire Tie Attache autobloquante Foam Tape Ruban mousse PART NUMBER H501SSJ000 Wire Snips ISSUE A SUBARU OF AMERICA PART NUMBER H501SSJ000 DATE 10/22/2021 1 Disconnect battery. If equipped disconnect eyelet cable only. Déconnectez la batterie. Si elle en est équipée, déconnectez le câble de l’œillet uniquement. PAGE 2/6 10 mm 12 mm 3 1 – Remove cover with trim tool starting from the front. 1 – Retirez le couvercle à l’aide de l’outil pour garniture en commençant par l’avant. 2 Remove original mirror by pulling on tab away from windshield and sliding mirror up and off the windshield mirror mount. Retirez le rétroviseur d’origine en tirant sur la languette pour l’éloigner du pare-brise et en faisant glisser le rétroviseur vers le haut pour le sortir du support 4 1 – For vehicles without Eyesight remove two screws. 1 – Pour les véhicules sans Eyesight, retirer les deux vis. ISSUE A SUBARU OF AMERICA PART NUMBER H501SSJ000 DATE 10/22/2021 PAGE 3/6 5 Gently pull down cover to release clips. Tirez doucement le couvercle vers le bas pour libérer les attaches. 6 Disconnect three harnesses from maplight/cover assembly. Débrancher les trois faisceaux de la lampe de lecture ou du couvercle. 7 Install auto-dimming mirror by sliding mirror down onto the base. Tighten set screw with T-20 Torx bit to 13.3 – 17.7 in-lbs. Installer le rétroviseur intérieur à atténuation automatique en le faisant glisser vers le bas sur la base. Serrer la vis de pression avec un embout Torx T-20 à 13,3 à 17,7 po-lb 8 Route wire harness through Eyesight cover opening. Faire passer le faisceau de câblage à travers l’ouverture du couvercle Eyesight. ISSUE A SUBARU OF AMERICA PART NUMBER H501SSJ000 DATE 10/22/2021 PAGE 4/6 9 Route harness between sheet metal and plastic bracket. Faire passer le faisceau entre la tôlerie et le support en plastique. 10 Connect mirror harness to pre-arranged vehicle harness. Brancher le faisceau du rétroviseur au faisceau du véhicule préinstallé. 11 Connect mirror harness to mirror. Brancher le faisceau du rétroviseur au rétroviseur. 12 Install mirror harness cover. Poser le couvercle du faisceau de rétroviseur. ISSUE A SUBARU OF AMERICA PART NUMBER H501SSJ000 DATE 10/22/2021 PAGE 5/6 13 Secure wire harness with wire tie. Fixer le faisceau de câblage avec une attache autobloquante. 15 14 Secure wire harness to sheet metal using foam tape to ensure wire harness does not rest on Eyesight module. Fixer le faisceau de câblage à la tôlerie à l’aide de ruban mousse pour s’assurer qu’il ne repose pas sur le module Eyesight. Reinstall map light/cover assembly. Réinstaller la lampe de lecture ou le couvercle. 16 Reconnect battery. If equipped reconnect eyelet cable. Tighten bolt to 66 in-lbs. Rebranchez la batterie. Si elle en est équipée, rebranchez le câble de l’œillet. Serrez les boulons à 66 po-lb. 10 mm 12 mm ISSUE A SUBARU OF AMERICA PART NUMBER H501SSJ000 DATE 10/22/2021 PAGE 6/6 17 18 Using dark cloth or cardboard, completely cover forward-looking sensor. Avec un linge sombre ou un carton, couvrez complètement le capteur pointé vers l’avant. To calibrate compass reference mirror user guide. Pour étalonne la boussole, reportez-vous au manuel du rétroviseur.
**************************************************************************************************************
SEOCONTENT-END