“This site contains affiliate links for which OEMDTC may be compensated” |
Accessory Installation Guide
2023MY Solterra – Door Edge Guard | PS936-42230-XX |
INSTALLATION
INSTRUCTIONS
PART NUMBER: PS936-42230-XX
DESCRIPTION: Solterra Door Edge Guard
PS936-42230-XX
https://static.oemdtc.com/AccessoryInstallationGuide/PS936-42230-XX.pdf
“This site contains affiliate links for which OEMDTC may be compensated” |
- 【PROTECT YOUR CAR DOORS WITH NO GLUE EDGE GUARDS】Prevent dings in crowed parking lot. Protect against paint chips/door dings. No glue, no messy. Protects your car doors edges as well as those cars parked next to you. 32-4/5Ft is long enough to be installed on 4 doors(vertically and horizontally)on most cars. Packaged in 1 roll so you can Custom Length and reduce wasting strips. Great gift for your families or friends.Open and close doors as usual, also helps reducing some wind/road noise.
- 【UNIVERSAL FIT MULTI-FUNCTIONS EDGE TRIM GUARDS】Fits most of Sedans, Trucks, SUV, ATV, UTV, Boats. Could be used as Truck Fender Fares, ATV edge guard, Boats edge seals, trailer door entry guard, automotive door entry guard, UTV edge guard, storage container seals, tool cart trim and decorative trim seals. Could be installed on front doors, back doors, back hatch door, bonnet edge. Make your cars look more sporty.
- 【BUILD IN METAL CLIPS, PERFECT TIGHTLY FITMENT】The two rubber fingers grip the door edge while the U-shaped aluminum pieces provide rigidity. Never drop even going through car washes and could hold the color over time.
- 【MADE WITH SUPER FLEXIBLE MATERIAL&QUICK AND EASY INSTALLATION】Made with flexible rubber material. Easily bends along the contours of your doors. Recommend to measure length of your doors before install, then use scissors to cut the edge guards. Could be installed in 15 minutes, much easier if you tap lightly with rubber mallet(not included).
- 【BACKED UP WITH SUPPORT FROM BRAND Winunite】FITS MOST OF CARS. NOT suitable for too thick door edges or those cars equipped with rubber strips. Please refer to our directions, recommend to tap lightly with rubber mallet(NOT included)for easier installation. Do remember to remove both ends of exposed metal clips before installing. If you have any question while using the product, please contact our customer service for help.
- GENUINE SUBARU DOOR EDGE GUARDS FOR YOUR 2019 2020 2021 2022 2023 SUBARU ASCENT.
- They help preserve the appearance of your Subaru while seamlessly blending into the door design.
- Help protect your door edges from dings and chips with custom-fit, body color-matched Door Edge Guards
- AVAILABLE IN MANY COLORS.
- Please send vin if you would like to check color code.
- 【PLEASE NOTE】❄It is cold in winter. Before use, you can use a hot air blower to heat the Clear door trim guard for better adhesion!⛄ High quality TPO rubber material, heat resistance, abrasion resistance, anti-aging, waterproof & UV resistance.
- 【EASY TO INSTALL】🧡 UNIVERSAL FIT!Just push on the Car Door Edge Guards above the install place.Could be installed in 15 minutes, much easier if you tap lightly with rubber mallet(not included).Attention to truck/van owners, please ensure your door edge thickness prior to purchase.😁
- 【TO CARE YOUR CAR】👍ADHESIVE: Built-in strong double-sided adhesive tape and does not melt under hot weather, no glue needed.They helps fit tightly and won't damage your door paint. No drop down even going through car washes. Open and close your doors easily.😁
- 【INVISIBLE DESIGN】🧡After installation, it is integrated with the door, and the hidden design protects your car door edge,almost invincible after installation.
- 【100% RISK-FREE WARRANTY】🤝One Year Warranty. Contact seller directly if any issues, EYTOOL Service Team will respond you within 24 hours during working days.😀
- Refuse nervous about opening the car door: SYOAUTO black car door edge guards can take out the worry of kids or other passengers accidentally hitting another car and scratching it up, even in the tight garage or narrow parking
- Your car door edge needs long-term protection: The door edge guard no need adhesive, reinforced with metal clips inside the rubber, won't scratch car paint. Always holds on tight even through direct sunlight, hard storms, or several car washes, never fall off
- 10-min quick installation: Snap to measure, cut, push onto door edge(much easier with a rubber mallet). The door trim has smooth edges, clean lines. fits like a glove. Opening and closing the door is still smooth. A good investment to save your paint
- A must-have to protect your car: This car door protector is flexible and hugs all curves easily. No adhesive melts in the heat, and no fading or cracking. Never worry about the car door edge scratching
- Textured black trim can blend in every color: Don't hesitate, the car door guard stays and look like part of any car door edge. An affordable method to protect car doors. It beats paying the extra cost for the factory version and install
- DON'T CHANGE THE APPEARANCE OF YOUR BEAUTIFUL CAR!!! PROTECT THE DOOR EDGES BUT DON'T RUIN HIS BEAUTY USING THOSE UGLY PLASTIC STRIPS !!!!! Our product virtually disappear while is still strongly protecting your car!!!
- THIS IS THE FAMOUS DOOR EDGE GUARD CLEAR PAINT PROTECTION FILM Easy to install: Installation can be done in 20 minutes. (Instructions included) Clear: Matches all paint colors. Maintain your car OEM appearance: Once installed, virtually disappear.
- Resistant: Heavy duty Urethane. Wash and wax resistant. UV Resistant: Stay clear for years. No yellowing or staining. Strong: Created for the Aeronautic industry. Effective: Protect from chips and abrasion.
- Professional results: The same product sells in dealers for much more. Durability: Lifetime of the car. Easy to remove: Just search for a corner and peel off. Maintenance: No special care is needed.
- 3M Clear Door Edge Guard Paint Protection Film Roll,3M's written instructions included.
- GENUINE SUBARU DOOR EDGE GUARDS FOR YOUR 2019 2020 FORESTER
- They help preserve the appearance of your Subaru while seamlessly blending into the door design.
- Help protect your door edges from dings and chips with custom-fit, body color-matched Door Edge Guards
- AVAILABLE IN MANY COLORS.
- Please send vin if you would like to check color code.
- High quality PVC natural rubber anti-collision strip, embedded with stainless steel framework, is wear-resistant and corrosion-resistant, effectively protecting your door from accidental opening and being worn by the walls and vehicles around you.
- There are five colors and two sizes for you to choose from, depending on your body type. They are installed on the four doors of most cars, such as cars, SUVs, trucks, etc. After installation, you can easily open and close the door without affecting the door.
- In the package, you will receive 16.4 feet (5M) or 33 feet (10M) crash strip and hammer; During installation, use scissors to cut the exposed iron sheet at both ends, clamp the anti-collision strip along the door edge, and then use a hammer to lock the rubber strip.
- The anti-collision strip can be used not only for doors, but also for sealing edges of ships, family doors and windows, computer tables, metal plates, shelf covers and other items that need to be protected.
- If you have any questions about the product and installation steps, please contact us via email, and we will provide a satisfactory solution.
- [Good Quality] The door edge protector is made of high-quality TPO rubber material, waterproof and moisture-proof. It is also flame retardant and heat insulating. When you drive in extreme weather conditions, it always holds tightly and won't fall off. After several car washes, this product remains in good condition.
- [Cuttable] The door edge decorative rubber sealing protective device is 16 feet long, and the material is soft, which can be easily bent along the door contour. It is recommended to measure the length of the door before installation, and then cut it to the length you need with scissors.
- [Self Adhesive] The U-shaped door protection device is equipped with strong double-sided adhesive tape, which can be easily bonded without glue. It's very cold. Before use, you can use the hot-air blower to heat the transparent door trim cover to obtain better adhesion!
- [Installation Method] Before installation, you need to clean the door edge to ensure that it is dry and clean. Then measure the size of your door and cut the edge guard with scissors. Finally, tap it with your hand to make it fit perfectly with the door. After installation, you can still open and close the door easily.
- [Function] Our door guards are applicable to most cars, SUVs, trucks and cars, and can be installed on the front door, rear door, rear hatch and engine hood edge. It can provide comprehensive protection for your vehicle, help maintain the vehicle condition, prevent the door from making noises and dents when opening and closing the door, and will not damage the door paint. Please pay attention to the truck/truck owner and ensure the thickness of the door edge before purchasing.
- ✔️ FLEXIBLE, SELF-ADHESIVE Edge Trim Adds Clear Protection Or A Colorful Lining To Your Car Door Edges
- ✔️ VEHICLE ACCESSORY This Versatile Door Guard Trim Adds A Touch Of Style To Vehicle Hoods And Trunks Too
- ✔️ CUSTOMIZE YOUR RIDE With A Vehicle Edge Accessory In Red, White, Silver, Orange, Blue And More Color Options
- ✔️ MADE IN THE USA From Strong Material That Easily Bends To Follow The Vehicle’s Curves And Bonds Quickly
- ✔️ UNIVERSAL FIT Edge Trim Is Enough For 2 Doors (10 Ft), Simple To Cut, And Installs In Minutes
- Car Door Sill Sticker: The door sill protector film is made of premium quality carbon fiber, sturdy and wear-resistant, durable and long lasting. Car door protector sill can be adjusted to fit most cars.
- Provide Full Protection: Car door edge sticker prevent door scratches, after install carbon door sill protector the rear/front door will not be scratches when loading and unloading, and Cover up existing scratches and prevent wear and tear, scratches, etc. , makes your car look unique and elegant.
- Verious Adventage: Car door edge entry guard film is waterproof and dirt-repellent, easy to clean with water, super waterproof and fire retardant, Stretchable with heat, good for non-slip on rainy days, making it more waterproof, more durable and more practical.
- Self-Adhesive: Easy to Peel and stick. Prevent the surface from dust and make sure it is always clean and new. Self-Adhesive Carbon fiber anti-scratch sticker is super sticky and can be stuck to any car and can be removed at any time without leaving any residue.
- Customer Service: Please feel free to contact us through Amazon Message Center If you have any issues with this car door sill protectors, we will give you a satisfying solution as soon as possible.
Last update on 2024-04-16 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.
SEOCONTENT-START
INSTALLATION INSTRUCTIONS PART NUMBER: PS936-42230-XX DESCRIPTION: Solterra Door Edge Guard KIT CONTENTS: TOOLS REQUIRED: Lint-Free Towel Painter’s Tape Scissors MEANING OF CHARACTERS: : CAUTION – A process that must be carefully observed in order to reduce the risk of damage to the accessory/vehicle and to ensure a quality installation. : STOP – Damage to the vehicle may occur. Do not proceed until process has been complied with. : TOOLS & EQUIPMENT – Specific Tools and equipment recommended for this process. STEP ONE: Prepare the Door’s Surface PART NUMBER: PS936-42230-XX DATE: 04-07-2022 SUBARU OF AMERICA PAGE 1/7 Isopropyl Alcohol ISOPROPYL ALCOHOL *Vaughan 12 oz. Rubber Mallet (or any 12 oz. Rubber Mallet) *Sealant Adjustment Tool Part #: SOA801AT100 It is strongly recommended that this product be installed by your Subaru Retailer. NOTE: If installing Body Side Moldings along with Door Edge Guards, the Body Side Moldings must be installed first. This is required for proper positioning of the two accessories. If the vehicle has Body Side Moldings previously installed and the distance between the edge of the Body Side Molding and edge of the door is less than 5mm, the Door Edge Guards will not be able to be installed due to spacing issues. 1a Before installation, confirm there is sufficient clearance between the door edge and the sealant bead for proper seating of the Door Edge Guard. ONLY USE THE TOOL IN THE AREA THE DOOR EDGE GUARD WILL BE INSTALLED Nylon Removal Tool SUFFICIENT CLEARANCE INSUFFICIENT CLEARANCE Looking Down the Door Edge ADJUSTING To adjust the seam sealer clearance when less than 2 mm exists between the door edge and the seam sealer, align the “green arrow” on the Sealant Adjustment Tool with the inside of the door’s edge. Place the pushing edge in the crease where door sealant bead and metal meet on the inside of the door (Figure C). Lightly push sealant adjustment tool in order to move sealant for preparation of install. It is critical that close attention be paid to the first 18mm of the sealant bead going down from the top where the Door Edge Guard starts and the last 18mm at the bottom where the Door Edge Guard ends for proper Door Edge Guard retention Door Edge Guard 4 pc. Paper Installation Templates (Pages 4 – 7) ISSUE: REV. – A Figure A Figure B Figure C CHECK SEALANT IN AREAS INDICATED BY GREEN LINE. STEP TWO: Installing the Door Edge Guards 2a 2b ENSURE MALLET HEAD IS PERPENDICULAR TO THE EDGE OF THE DOOR. HOLD MALLET AS SHOWN. HOLDING DOOR EDGE GUARD IN PROPER ALIGNMENT WITH ONE HAND, DIRECTLY & DELIBERATELY PERFORM INITIAL STRIKE AT STRIKE POINT #1. PART NUMBER: PS936-42230-XX DATE: 04-07-2022 SUBARU OF AMERICA PAGE 2/7 1b x4 DRY ALL DOOR EDGES ROTATE TOWEL AFTER EACH WIPE SQUEAK RESISTANCE MUST BE FELT & “SQUEAKY CLEAN” SOUND HEARD WHILE DRYING ***IMPORTANT*** PREP ALL DOOR EDGES WITH ISOPROPYL ALCOHOL TO REMOVE ALL SURFACE WAX ISOPRO ALCOH START !! CUT OUT PAPER TEMPLATES ON PAGES 4 – 7. FIT THE NOTCH OF THE TEMPLATE AROUND DOOR HANDLE. ALIGN TAB FLUSH WITH DOOR EDGE. TAPE PAPER TEMPLATE TO DOOR. ALIGN USE SOFT SIDE OF RUBBER MALLET ONLY ALIGN TOP EDGE OF DOOR EDGE GUARD WITH LOWER EDGE OF TEMPLATE ALIGNMENT NOTCH. ISSUE: REV. – A DATE: 04-07-2022 PART NUMBER: PS936-42230-XX SUBARU OF AMERICA PAGE 3/7 2c CONTINUE WITH FIRM TAPPING MOVING UPWARD BETWEEN STRIKE POINTS #1 & 4 AT ½ INCH INTERVALS. VISUALLY ENSURE DOOR EDGE GUARD IS FULLY ENGAGED, THEN START BACK AT STRIKING POINT #1 TAPPING DOWNWARD ENTIRE LENGTH OF DOOR EDGE GUARD. Door Edge Guard Removal THE DOOR EDGE GUARDS ARE MEANT FOR PERMANENT INSTALLATION AND ARE NOT TO BE REMOVED. IF A DOOR EDGE GUARD IS REMOVED FOR ANY REASON, IT CANNOT BE REINSTALLED. A NEW DOOR EDGE GUARD KIT MUST BE USED. ~½” ~½” STARTING FROM EITHER THE TOP OR BOTTOM OF DOOR EDGE GUARD, LIGHTLY TAP NYLON REMOVAL TOOL ALONG GUARD EDGE IN ½” INTERVALS MOVING DOWN OR UP UNTIL ~2” OF DOOR EDGE GUARD IS DISENGAGED. REPEAT THIS PROCESS AT OTHER END. ONCE ~2” OF BOTH TOP AND BOTTOM OF DOOR EDGE GUARD IS DISENGAGED, CONTINUE UP OR DOWN ENTIRE DOOR EDGE GUARD LENGTH UNTIL REMOVAL IS COMPLETE. ~½” ~½” = 2d THUD 2c ~1” THUD REPEAT ALL DOORS ONCE FULLY ENGAGED, PROGRESSIVELY TAP UP ENTIRE LENGTH OF DOOR EDGE GUARD. IF FULLY SEATED, A SOLID “THUD” SHOULD BE HEARD. IF NOT HEARD, REPEAT STEP 2c. ISSUE: REV. – A Front Driver Door Template: Retailer Installation Note: To ensure correct print sizing, set Page Size to “Legal” under Printer Properties and “Actual size” under Page Sizing and Handling. Check above scale to ensure it is 1:1. Adjust on photocopier if it is not to scale. PART NUMBER: PS936-42230-XX DATE: 04-07-2022 SUBARU OF AMERICA PAGE 4/7 ISSUE: REV. – A P/N BZ423-0003 Solterra Front Driver Door Door Edge GuardMounting Template Front Passenger Door Template: Retailer Installation Note: To ensure correct print sizing, set Page Size to “Legal” under Printer Properties and “Actual size” under Page Sizing and Handling. Check above scale to ensure it is 1:1. Adjust on photocopier if it is not to scale. PART NUMBER: PS936-42230-XX DATE: 04-07-2022 SUBARU OF AMERICA PAGE 5/7 ISSUE: REV. – A P/N BZ423-0003 1111 111111 Solterra Front Passenger Door Door Edge GuardMounting Template Rear Driver Door Template: Retailer Installation Note: To ensure correct print sizing, set Page Size to “Legal” under Printer Properties and “Actual size” under Page Sizing and Handling. Check above scale to ensure it is 1:1. Adjust on photocopier if it is not to scale. PART NUMBER: PS936-42230-XX DATE: 04-07-2022 SUBARU OF AMERICA PAGE 6/7 ISSUE: REV. – A P/N BZ423-0003 Solterra Rear Driver Door Door Edge Guard Mounting Template Rear Passenger Door Template: Retailer Installation Note: To ensure correct print sizing, set Page Size to “Legal” under Printer Properties and “Actual size” under Page Sizing and Handling. Check above scale to ensure it is 1:1. Adjust on photocopier if it is not to scale. PART NUMBER: PS936-42230-XX DATE: 04-07-2022 SUBARU OF AMERICA PAGE 7/7 ISSUE: REV. – A P/N BZ423-0003 Solterra Rear Passenger Door Door Edge Guard Mounting Template : ARRÊT – Risque d’endommagement au véhicule. Ne pas continuer avant d’avoir complété la procédure précédente. INSTRUCTIONS D’INSTALLATION NUMÉRO DE PIÈCE : PS936-42230-XX DESCRIPTION : Protection de bord de porte Solterra CONTENU DU NÉCESSAIRE : OUTILS REQUIS : Ruban-cache Serviette non pelucheuse Ciseaux *Maillet de caoutchouc Vaughan 12 onces (ou tout maillet de caoutchouc de 12 onces) SIGNIFICATION DES SYMBOLES : : AVERTISSEMENT – Procédé qui doit être rigoureusement suivi afin de réduire le risque d’endommagement de l’accessoire / du véhicule et pour assurer une installation de qualité. : OUTILS ET ÉQUIPEMENT – Outils et équipements spécifiques recommandés pour ce travail. PREMIÈRE ÉTAPE : Préparer la surface de la porte NUMÉRO DE PIÈCE : PS936-42230-XX DATE : 04-07-2022 SUBARU OF AMERICA PAGE 1/7 Alcool isopropylique ALCOOL ISOPROPYLIQUE Protection de bord de porte (4 unités) *Outil d’ajustement pour l’étanchéité – No de pièce : SOA801AT100 Il est fortement recommandé de faire installer ce produit par votre concessionnaire Subaru. REMARQUE : Si vous installez les baguettes de flanc avec les bords de portes protégés, les baguettes de flanc doivent être installées en premier. Cela est nécessaire pour un positionnement approprié des deux accessoires. Si des baguettes de flanc ont été précédemment posées sur le véhicule et que la distance entre le rebord des baguettes de flanc et la porte est inférieure à 5 mm, la protection de bord de porte ne pourra pas être installée en raison du manque d’espace. 1a Avant l’installation, confirmez qu’il y a un dégagement suffisant entre le bord de la porte et le bourrelet d’étanchéité pour veiller au bon positionnement de la protection de bord de porte. UTILISEZ SEULEMENT L’OUTIL DANS LA ZONE OÙ LA PROTECTION DE BORD DE PORTE SERA INSTALLÉE Gabarits pour l’installation (pages 4 et 7) Outil de dépose en nylon DÉGAGEMENT SUFFISANT DÉGAGEMENT INSUFFISANT Vue de dessus du bord de la porte Pour régler le dégagement du produit d’étanchéité lorsqu’il y a moins de 2 mm entre le rebord de la portière et le produit d’étanchéité, alignez la « flèche verte » sur l’outil de réglage du produit d’étanchéité avec l’intérieur du rebord de la portière. Placez le rebord poussant dans la nervure, là où le cordon du produit d’étanchéité de la portière et le métal se rencontrent à l’intérieur de la portière (Figure C). Poussez légèrement l’outil de réglage du produit d’étanchéité afin de le déplacer en vue de la préparation de l’installation. Il est essentiel de porter une attention particulière aux premiers 18 mm du cordon du produit d’étanchéité qui descendent du haut où commence le protège-rebords de portière et aux derniers 18 mm au bas où il s’arrête afin de garantir une retenue adéquate. Figure A AJUSTEMENT VÉRIFIEZ L’ÉTANCHÉITÉ DANS LES ZONES INDIQUÉES PAR UNE LIGNE VERTE. VERSION: REV. – A Figure B Figure C DEUXIÈME ÉTAPE : Installation de la protection de bord de porte NUMÉRO DE PIÈCE : PS936-42230-XX DATE : 04-07-2022 SUBARU OF AMERICA PAGE 2/7 2b S’ASSURER QUE LA TÊTE DU MAILLET EST PERPENDICULAIRE AU BORD DE PORTE. TENIR LE MAILLET COMME SUR L’ILLUSTRATION. MAINTENIR EN PLACE LA PROTECTION DE BORD DE PORTE AVEC LA MAIN ET FRAPPER DIRECTEMENT ET FERMEMENT AU POINT DE FRAPPE NO 1. EXTÉRIEUR INTÉRIEUR 2a ALIGNER DÉCOUPER LE GABARIT AUX PAGES 4 ET 7, PUIS L’AJUSTER AUTOUR DE LA POIGNÉE DE PORTE. ALIGNER L’ONGLET POUR QU’IL AFFLEURE LE BORD DE LA PORTE. FIXER LE GABARIT SUR LA PORTE AVEC DU RUBAN-CACHE. UTILISER UNIQUEMENT LE CÔTÉ MOU DU MAILLET DE CAOUTCHOUC ALIGNER L’EXTRÉMITÉ SUPÉRIEURE DE LA PROTECTION DE BORD DE PORTE AVEC LA DÉCOUPE SUR LA PARTIE INFÉRIEURE DE L’ONGLET DU GABARIT. 1b 4 X SÉCHER TOUS LES BORDS DE PORTE INVERSER LA SERVIETTE APRÈS CHAQUE PASSAGE COUIC VOUS DEVEZ SENTIR UNE RÉSISTANCE ET ENTENDRE UN BRUIT DE « COUINEMENT » AU MOMENT DU SÉCHAGE ***IMPORTANT*** NETTOYER TOUS LES BORDS DE PORTES AVEC DE L’ALCOOL ISOPROPYLIQUE POUR ENLEVER LA CIRE ALCOOL ISOPRO POINT DE DÉPART Point de frappe VERSION: REV. – A DATE : 04-07-2022 NUMÉRO DE PIÈCE : PS936-42230-XX SUBARU OF AMERICA PAGE 3/7 2c CONTINUER EN FRAPPANT FERMEMENT VERS LE HAUT ENTRE LE POINT DE FRAPPE NO1 ET 4 À ½ PO D’INTERVALLE. S’ASSURER QUE LA PROTECTION DE BORD DE PORTE EST COMPLÈTEMENT ENFONCÉE, PUIS FRAPPER EN REMONTANT VERS LE HAUT DE LA PROTECTION DE BORD DE PORTE. LA PROTECTION DE BORD DE PORTE EST UN ACCESSOIRE FIXE QUI NE DOIT PAS ÊTRE ENLEVÉ. SI UNE PROTECTION DE PORTE EST RETIRÉE POUR QUELQUE RAISON QUE CE SOIT, ELLE NE POURRA PAS ÊTRE INSTALLÉE DE NOUVEAU. IL FAUDRA ALORS EN UTILISER UNE NOUVELLE. Dépose du protecteur de bord de porte ~½” ~½” EN COMMENÇANT PAR LE HAUT OU LE BAS DU PROTECTEUR DE BORD DE PORTE, FRAPPER LÉGÈREMENT L’OUTIL DE DÉPOSE EN NYLON LE LONG DU BORD DU PROTECTEUR À INTERVALLE DE 1/2 PO EN LE DÉPLAÇANT VERS LE HAUT OU VERS LE BAS JUSQU’À CE LE PROTECTEUR DE BORD DE PORTE SOIT DÉGAGÉ D’ENVIRON 2 PO. RÉPÉTER LA MÊME PROCÉDURE DE L’AUTRE CÔTÉ. DÈS QU’UNE PORTION D’ENVIRON 2 PO DU HAUT ET DU BAS EST DÉGAGÉE, CONTINUER À PROCÉDER PAR MOUVEMENT VERTICAL VERS LE HAUT OU VERS LE BAS SUR TOUTE LA LONGUEUR DU PROTECTEUR JUSQU’À SON RETAIT COMPLET. BRUIT SOURD = 2d 2c ~1 po BRUIT SOURD RÉPÉTER SUR TOUTES LES PORTES UNE FOIS LA PROTECTION BIEN ENGAGÉE, MARTELER VERS LE HAUT SUR TOUTES LA LONGUEUR. LORSQUE LA PROTECTION EST ENFONCÉE CORRECTEMENT, UN BRUIT SOURD SE FAIT ENTENDRE. DANS LE CAS CONTRAIRE, RECOMMENCER L’ÉTAPE 2c. ~½ po ~½ po VERSION: REV. – A Gabarits de portes avant du côté du conducteur : NUMÉRO DE PIÈCE : PS936-42230-XX DATE : 04-07-2022 SUBARU OF AMERICA PAGE 4/7 Directive d’installation au concessionnaire : Pour assurer des dimensions d’impression appropriées, réglez la dimension de page à « Légal » dans l’onglet des propriétés de l’imprimante et « Taille réelle » dans l’onglet des dimensions et du traitement de la page. Vérifier que l’échelle est exacte à 1:1. Dans le cas contraire, régler le photocopieur. VERSION: REV. – A Solterra Porte avant côté conducteur Point de frappe initiaI 111111111111111 1 Gabarits de portes avant du côté du passager : NUMÉRO DE PIÈCE : PS936-42230-XX DATE : 04-07-2022 SUBARU OF AMERICA PAGE 5/7 Directive d’installation au concessionnaire : Pour assurer des dimensions d’impression appropriées, réglez la dimension de page à « Légal » dans l’onglet des propriétés de l’imprimante et « Taille réelle » dans l’onglet des dimensions et du traitement de la page. Vérifier que l’échelle est exacte à 1:1. Dans le cas contraire, régler le photocopieur. VERSION: REV. – A côté parallèle à la ligne de carrosserie Solterra Porte avant côté passager Point de frappe initial Gabarit de montage de la protection de bord de porte Nº de pièce BZ423-0001 Brevet É.-U. no 8,709,180 NUMÉRO DE PIÈCE : PS936-42230-XX DATE : 04-07-2022 SUBARU OF AMERICA PAGE 6/7 Gabarits de portes arrière du côté du conducteur : Directive d’installation au concessionnaire : Pour assurer des dimensions d’impression appropriées, réglez la dimension de page à « Légal » dans l’onglet des propriétés de l’imprimante et « Taille réelle » dans l’onglet des dimensions et du traitement de la page. Vérifier que l’échelle est exacte à 1:1. Dans le cas contraire, régler le photocopieur. VERSION: REV. – A Solterra Porte arrière côté conducteur conducteur NUMÉRO DE PIÈCE : PS936-42230-XX DATE : 04-07-2022 SUBARU OF AMERICA PAGE 7/7 Gabarits de portes arrière du côté du passager : Directive d’installation au concessionnaire : Pour assurer des dimensions d’impression appropriées, réglez la dimension de page à « Légal » dans l’onglet des propriétés de l’imprimante et « Taille réelle » dans l’onglet des dimensions et du traitement de la page. Vérifier que l’échelle est exacte à 1:1. Dans le cas contraire, régler le photocopieur. VERSION: REV. – A Solterra Porte arrière côté passager
SEOCONTENT-END