| “This site contains affiliate links for which OEMDTC may be compensated” |
Accessory Installation Guide
| 2024MY Crosstrek Door Edge Guard | SOA801P091 |
INSTALLATION
INSTRUCTIONS
PART NUMBER: SOA801P091-XX
DESCRIPTION: Crosstrek Door Edge Guard
It is strongly recommended that this product be installed by your Subaru
Retailer.
NOTE: If installing Body Side Moldings along with Door Edge Guards, the Body Side Moldings must be installed This is require d for proper positioning of the two accessories. If the vehicle has Body Side Moldings previously installed and the distance between the edge of the Body Si de Molding and edge of the door is less than 5mm, the Door Edge Guards will not be able to be installed due to spacing issues.
Before installation, confirm there is sufficient clearance between the door edge and the sealant bead for proper seating of the Door Edge Guard.
ONLY USE THE TOOL IN THE AREA THE DOOR EDGE GUARD WILL BE INSTALLED
To adjust the seam sealer clearance when less than 2 mm exists between the door edge and the seam sealer, align the “green arrow ” on the Sealant Adjustment Tool with the inside of the door’s edge. Place the pushing edge in the crease where door sealant bead and metal meet on the inside of the door (Figure C). Lightly push sealant adjustment tool in order to move sealant for preparation of install. It is critical that close attention be paid to the first 18mm of the sealant bead going down from the top where the Door Edge Guard starts and the last 18mm at the bottom where the Door Edge Guard ends for proper Door Edge Guard retention
SOA801P091
ISSUE: REV. A
DATE: 11-01 2022
Loading...
Reload document 
Open in new tab
| “This site contains affiliate links for which OEMDTC may be compensated” |
- 【No Glue Required. Protect Against Paint Chips/Door Dings】You don't need to worry about hitting or denting neighboring cars after installing the edge guard strips. Protects your car doors edges as well as those cars parked next to you. Gives you the confidence to open your car doors in tight parking lot. No glue, No messy. Came with microfiber cloth. It helps you to clean door edges before installation
- 【Fits Most Cars. Multi-Functions Edge Trim Guards】Fits most of Sedans, Trucks, SUV. Could be used as Truck Fender Fares, Could be installed on front doors, back doors, back hatch door, bonnet edge
- 【Build in Metal Clips. Tightly Fitment】The two rubber fingers grip the door edge while the U-shaped aluminum pieces provide rigidity. Rarely Falls Off When Washing the Car and it could hold the color over time
- 【Made with Flexible Material. Quick and Easy Install】Made with flexible rubber material. Easily bends along the contours of your doors. Recommend to refer to our directions and measure length of your doors before install
- 【Backed Up with Support from Brand Winunite】Fits most of cars. NOT suitable for too thick(5mm or greater) door edges or those cars equipped with pre-installed sealing strips. If you have any question while using the product, please contact our customer service for help
- 【Durable】 Waterproof, Isolator Noise, Corrosion Resistance, High-Temperature Resistance, Wear Resistance, Anti-Aging, Uv Resistance.
- 【High Versatility】 The package include 2 roll of car door edge guards, total 33Ft(10M) long. Edge Thickness: 2Mm( 0.78"). Product Specifications As Shown In Figure. These Door Edge Guards Will Protect Your Vehicle From Nicks, Chips and Scratches, For Most Universal Car.
- 【No Drop Off】 Car door edge guard with 4 fixed slices, completely tightly fit, no drop-off.
- 【The Install Place】 1.In The Metal Edge Of The Car Body Between The Car Door And Car Body. In The External Edge Of The Car Door And More. 2. Also Can Be Use In The Window Above The Car. Window Panel Minibus. Border Heavy Equipment. Covering The Edge Of The Sharp Metal. Vinyl Window Decoration Boat.
- 【Easy To Install】 Just press the rubber seal on the car door edge and it can hold it tight, adhesive-free keeps your door edge clean when you take it off. (Attention To Truck/Van Owners, Please Ensure Your Door Edge Thickness Prior To Purchase.)
- Genuine Subaru
Door Edge Guards for Your 2025 Forester - They help preserve the appearance of your Subaru while seamlessly blending into the door design.
- Help protect your door edges from dings and chips with custom-fit, body color-matched Door Edge Guards
- AVAILABLE IN MANY COLORS.
- Please send vin if you would like to check color code.
- 【PLEASE NOTE】❄It is cold in winter. Before use, you can use a hot air blower to heat the Clear door trim guard for better adhesion!⛄ High quality TPO rubber material, heat resistance, abrasion resistance, anti-aging, waterproof & UV resistance.
- 【EASY TO INSTALL】🧡 UNIVERSAL FIT!Just push on the Car Door Edge Guards above the install place.Could be installed in 15 minutes, much easier if you tap lightly with rubber mallet(not included).Attention to truck/van owners, please ensure your door edge thickness prior to purchase.😁
- 【TO CARE YOUR CAR】👍ADHESIVE: Built-in strong double-sided adhesive tape and does not melt under hot weather, no glue needed.They helps fit tightly and won't damage your door paint. No drop down even going through car washes. Open and close your doors easily.😁
- 【INVISIBLE DESIGN】🧡After installation, it is integrated with the door, and the hidden design protects your car door edge,almost invincible after installation.
- 【100% RISK-FREE WARRANTY】🤝One Year Warranty. Contact seller directly if any issues, EYTOOL Service Team will respond you within 24 hours during working days.😀
- Refuse nervous about opening the car door: SYOAUTO black car door edge guards can take out the worry of kids or other passengers accidentally hitting another car and scratching it up, even in the tight garage or narrow parking
- Your car door edge needs long-term protection: The door edge guard no need adhesive, reinforced with metal clips inside the rubber, won't scratch car paint. Always holds on tight even through direct sunlight, hard storms, or several car washes, never fall off
- 10-min quick installation: Snap to measure, cut, push onto door edge(much easier with a rubber mallet). The door trim has smooth edges, clean lines. fits like a glove. Opening and closing the door is still smooth. A good investment to save your paint
- A must-have to protect your car: This car door protector is flexible and hugs all curves easily. No adhesive melts in the heat, and no fading or cracking. Never worry about the car door edge scratching
- Textured black trim can blend in every color: Don't hesitate, the car door guard stays and look like part of any car door edge. An affordable method to protect car doors. It beats paying the extra cost for the factory version and install
- GENUINE SUBARU DOOR EDGE GUARDS FOR YOUR 2019 2020 2021 2022 2023 2024 FORESTER
- They help preserve the appearance of your Subaru while seamlessly blending into the door design.
- Help protect your door edges from dings and chips with custom-fit, body color-matched Door Edge Guards
- AVAILABLE IN MANY COLORS.
- Please send vin if you would like to check color code.
- Genuine Subaru Door Edge Guards for your 2023-2025 Outback or 2022-2025 Outback Wilderness.
- They help preserve the appearance of your Subaru while seamlessly blending into the door design.
- Help protect your door edges from dings and chips with custom-fit, body color-matched Door Edge Guards
- Available In Many Colors
- Please send vin if you would like to check color code.
- Genuine Subaru Door Edge Guards for your 2020-2022 Outback & 2020-2025 Legacy
- They help preserve the appearance of your Subaru while seamlessly blending into the door design.
- Help protect your door edges from dings and chips with custom-fit, body color-matched Door Edge Guards
- Avalibable In Many Colors Non Wilderness Outback
- Please send vin if you would like to check color code.
- High quality PVC natural rubber anti-collision strip, embedded with stainless steel framework, is wear-resistant and corrosion-resistant, effectively protecting your door from accidental opening and being worn by the walls and vehicles around you.
- There are five colors and two sizes for you to choose from, depending on your body type. They are installed on the four doors of most cars, such as cars, SUVs, trucks, etc. After installation, you can easily open and close the door without affecting the door.
- In the package, you will receive 16.4 feet (5M) or 33 feet (10M) crash strip and hammer; During installation, use scissors to cut the exposed iron sheet at both ends, clamp the anti-collision strip along the door edge, and then use a hammer to lock the rubber strip.
- The anti-collision strip can be used not only for doors, but also for sealing edges of ships, family doors and windows, computer tables, metal plates, shelf covers and other items that need to be protected.
- If you have any questions about the product and installation steps, please contact us via email, and we will provide a satisfactory solution.
- Premium Car Door Edge Guard Trim: Cowles Products offers high-quality car door edge guard trim that provides superior protection for your vehicle. Say goodbye to cracks and hello to durable door protection that stays in place, thanks to the reliable automotive grade hot melt glue adhesives.
- Enhance the Look of Your Vehicle: Choose from our wide range of options, including black door edge guard, carbon fiber style car door protectors, or chrome door edge trim. These stylish choices not only safeguard your car, truck, or SUV but also add an aesthetic appeal to your vehicle's appearance.
- Versatile Protection for Various Areas: Our car door edge trim is not limited to protecting only the doors. It can also be effectively used to safeguard the edges of hoods and trunks from chips and nicks that may lead to rust over time. Give your entire vehicle the protection it deserves.
- Easy Installation and Customizable Length: Installing our door edge guard trim is a breeze. It is designed to be easily installed by anyone. Additionally, the trim is flexible around edges, allowing for a seamless fit. You can also trim or cut it to your desired length, ensuring a perfect fit for your specific vehicle.
- Universal Fit for All Vehicles: Cowles Products' Car Door Edge Guard Trim is designed to have a universal fit, making it compatible with almost all types of vehicles. Whether you have a car, truck, SUV, or any other vehicle, our trim will provide the protection you need without compromising on quality or style.
Last update on 2025-04-17 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.
SEOCONTENT-START
PART NUMBER: SOA801P091-XX DESCRIPTION: Crosstrek Door Edge Guard KIT CONTENTS: TOOLS REQUIRED: Lint-Free Towel cissors Painter’s Tape n MEANING OF CHARACTERS: : CAUTION – A process that must be carefully observed in order to reduce the risk of damage to the accessory/vehicle and to ensure a quality installation. : STOP – Damage to the vehicle may occur. Do not proceed until process has been complied with. : TOOLS & EQUIPMENT – Specific Tools and equipment recommended for this process. STEP ONE: Prepare the Door’s Surface PART NUMBER: SOA801P091-XX . – A DATE: 11-01-2022 SUBARU OF AMERICA PAGE ISOPROPYL ALCOHOL *Sealant Adjustment ghan 12 oz. Tool Part #: SOA801AT100 Pages 4 – 7) (or any 12 oz. Rubber Mallet) moval Tool It is strongly recommended that this product be installed by your Subaru Retailer. NOTE: If installing Body Side Moldings along with Door Edge Guards, the Body Side Moldings must be installed first. This is required for proper positioning of the two accessories. If the vehicle has Body Side Moldings previously installed and the distance between the edge of the Body Side Molding and edge of the door is less than 5mm, the Door Edge Guards will not be able to be installed due to spacing issues. 1a Before installation, confirm there is sufficient clearance between the door edge and the sealant bead for proper seating of the Door Edge Guard. ONLY USE THE TOOL IN THE AREA THE DOOR EDGE GUARD WILL BE INSTALLED SUFFICIENT CLEARANCE INSUFFICIENT CLEARANCE Looking Down the Door Edge ADJUSTING To adjust the seam sealer clearance when less than 2 mm exists between the door edge and the seam sealer, align the “green arrow” on the Sealant Adjustment Tool with the inside of the door’s edge. Place the pushing edge in the crease where door sealant bead and metal meet on the inside of the door (Figure C). Lightly push sealant adjustment tool in order to move sealant for preparation of install. It is critical that close attention be paid to the first 18mm of the sealant bead going down from the top where the Door Edge Guard starts and the last 18mm at the bottom where the Door Edge Guard ends for proper Door Edge Guard retention Door Edge Guard 4 pc. Figure A Figure B Figure C CHECK SEALANT IN AREAS INDICATED BY GREEN LINE. 1b ISOPRO ALCOH ***IMPORTANT*** PREP ALL DOOR EDGES WITH ISOPROPYL ALCOHOL TO REMOVE ALL SURFACE WAX ROTATE TOWEL AFTER EACH WIPE DRY ALL DOOR EDGES RESISTANCE MUST BE FELT & “SQUEAKY CLEAN” SOUND HEARD WHILE DRYING SQUEAK STEP TWO: Installing the Door Edge Guards 2a ALIGN USE SOFT SIDE OF RUBBER MALLET ONLY CUT OUT PAPER TEMPLATES ON PAGES 4 – 7. FIT THE NOTCH OF THE TEMPLATE AROUND DOOR HANDLE. ALIGN TAB FLUSH WITH DOOR EDGE. TAPE PAPER TEMPLATE TO DOOR. ALIGN TOP EDGE OF DOOR EDGE GUARD WITH LOWER EDGE OF TEMPLATE ALIGNMENT NOTCH. 2b ENSURE MALLET HEAD IS PERPENDICULAR TO THE EDGE OF THE DOOR. HOLD MALLET AS SHOWN. START !! HOLDING DOOR EDGE GUARD IN PROPER ALIGNMENT WITH ONE HAND, DIRECTLY & DELIBERATELY PERFORM INITIAL STRIKE AT STRIKE POINT #1. PART NUMBER: SOA801P091-XX ISSUE: REV. – A DATE: 11-01-2022 SUBARU OF AMERICA PAGE 2/7 2c ~½” ~½” CONTINUE WITH FIRM TAPPING MOVING UPWARD BETWEEN STRIKE POINTS #1 & 4 AT ½ INCH INTERVALS. VISUALLY ENSURE DOOR EDGE GUARD IS FULLY ENGAGED, THEN START BACK AT STRIKING POINT #1 TAPPING DOWNWARD ENTIRE LENGTH OF DOOR EDGE GUARD. 2d ~1” THUD = REPEAT ALL DOORS THUD 2c ONCE FULLY ENGAGED, PROGRESSIVELY TAP UP ENTIRE LENGTH OF DOOR EDGE GUARD. IF FULLY SEATED, A SOLID “THUD” SHOULD BE HEARD. IF NOT HEARD, REPEAT STEP 2c. Door Edge Guard Removal THE DOOR EDGE GUARDS ARE MEANT FOR PERMANENT INSTALLATION AND ARE NOT TO BE REMOVED. IF A DOOR EDGE GUARD IS REMOVED FOR ANY REASON, IT CANNOT BE REINSTALLED. A NEW DOOR EDGE GUARD KIT MUST BE USED. ~½” ~½” STARTING FROM EITHER THE TOP OR BOTTOM OF DOOR EDGE GUARD, LIGHTLY TAP NYLON REMOVAL TOOL ALONG GUARD EDGE IN ½” INTERVALS MOVING DOWN OR UP UNTIL ~2” OF DOOR EDGE GUARD IS DISENGAGED. REPEAT THIS PROCESS AT OTHER END. ONCE ~2” OF BOTH TOP AND BOTTOM OF DOOR EDGE GUARD IS DISENGAGED, CONTINUE UP OR DOWN ENTIRE DOOR EDGE GUARD LENGTH UNTIL REMOVAL IS COMPLETE. PART NUMBER: SOA801P091-XX ISSUE: REV. – A DATE: 11-01-2022 SUBARU OF AMERICA PAGE 3/7 Retailer Installation Note: To ensure correct print sizing, set Page Size to “Legal” under Printer Properties and “Actual size” under Page Sizing and Handling. Check above scale to ensure it is 1:1. Adjust on photocopier if it is not to scale. Retailer Installation Note: To ensure correct print sizing, set Page Size to “Legal” under Printer Properties and “Actual size” under Page Sizing and Handling. Check above scale to ensure it is 1:1. Adjust on photocopier if it is not to scale. Rear Driver Door Template: MY24 Subaru Impreza / Crosstrek / Crosstrek Wilderness Rear Driver Door Retailer Installation Note: To ensure correct print sizing, set Page Size to “Legal” under Printer Properties and “Actual size” under Page Sizing and Handling. Check above scale to ensure it is 1:1. Adjust on photocopier if it is not to scale. PART NUMBER: SOA801P091-XX ISSUE: DATE: REV. – A 11-01-2022 SUBARU OF AMERICA PAGE 6/7 Rear Passenger Door Template: MY24 Subaru Impreza / Crosstrek / Crosstrek Wilderness Rear Passenger Door Retailer Installation Note: To ensure correct print sizing, set Page Size to “Legal” under Printer Properties and “Actual size” under Page Sizing and Handling. Check above scale to ensure it is 1:1. Adjust on photocopier if it is not to scale. PART NUMBER: SOA801P091-XX ISSUE: REV. – A DATE: 11-01-2022 SUBARU OF AMERICA PAGE 7/7 NUMÉRO DE PIÈCE : SOA801P091-XX INSTRUCTIONS D’INSTALLATION CONTENU DU NÉCESSAIRE : DESCRIPTION : Protection de bord de porte Crosstrek OUTILS REQUIS : Protection de bord de porte (4 unités) *Outil d’ajustement pour l’étanchéité – No de pièce : SOA801AT100 ALCOOL ISOPROPYLIQUE Alcool isopropylique Serviette non pelucheuse Ciseaux Gabarits pour l’installation (pages 4 et 7) Ruban-cache *Maillet de caoutchouc Vaughan 12 onces (ou tout maillet de caoutchouc de 12 onces) Outil de dépose en nylon Il est fortement recommandé de faire installer ce produit par votre concessionnaire Subaru. REMARQUE : Si vous installez les baguettes de flanc avec les bords de portes protégés, les baguettes de flanc doivent être installées en premier. Cela est nécessaire pour un positionnement approprié des deux accessoires. Si des baguettes de flanc ont été précédemment posées sur le véhicule et que la distance entre le rebord des baguettes de flanc et la porte est inférieure à 5 mm, la protection de bord de porte ne pourra pas être installée en raison du manque d’espace. SIGNIFICATION DES SYMBOLES : : AVERTISSEMENT – Procédé qui doit être rigoureusement suivi afin de réduire le risque d’endommagement de l’accessoire / du véhicule et pour assurer une installation de qualité. : ARRÊT – Risque d’endommagement au véhicule. Ne pas continuer avant d’avoir complété la procédure précédente. : OUTILS ET ÉQUIPEMENT – Outils et équipements spécifiques recommandés pour ce travail. PREMIÈRE ÉTAPE : Préparer la surface de la porte 1a VÉRIFIEZ L’ÉTANCHÉITÉ DANS LES ZONES INDIQUÉES PAR UNE LIGNE VERTE. Avant l’installation, confirmez qu’il y a un dégagement suffisant entre le bord de la porte et le bourrelet d’étanchéité pour veiller au bon positionnement de la protection de bord de porte. UTILISEZ SEULEMENT L’OUTIL DANS LA ZONE OÙ LA PROTECTION DE BORD DE PORTE SERA INSTALLÉE Vue de dessus du bord de la porte DÉGAGEMENT SUFFISANT DÉGAGEMENT INSUFFISANT AJUSTEMENT Figure A Figure B Figure C Pour régler le dégagement du produit d’étanchéité lorsqu’il y a moins de 2 mm entre le rebord de la portière et le produit d’étanchéité, alignez la « flèche verte » sur l’outil de réglage du produit d’étanchéité avec l’intérieur du rebord de la portière. Placez le rebord poussant dans la nervure, là où le cordon du produit d’étanchéité de la portière et le métal se rencontrent à l’intérieur de la portière (Figure C). Poussez légèrement l’outil de réglage du produit d’étanchéité afin de le déplacer en vue de la préparation de l’installation. Il est essentiel de porter une attention particulière aux premiers 18 mm du cordon du produit d’étanchéité qui descendent du haut où commence le protège-rebords de portière et aux derniers 18 mm au bas où il s’arrête afin de garantir une retenue adéquate. NUMÉRO DE PIÈCE : VERSION: DATE : SUBARU OF AMERICA PAGE SOA801P091-XX REV. – A 11-01-2022 1/7 1b ALCOOL ISOPRO ***IMPORTANT*** NETTOYER TOUS LES BORDS DE PORTES AVEC DE L’ALCOOL ISOPROPYLIQUE POUR ENLEVER LA CIRE INVERSER LA SERVIETTE APRÈS CHAQUE PASSAGE SÉCHER TOUS LES BORDS DE PORTE VOUS DEVEZ SENTIR UNE RÉSISTANCE ET ENTENDRE UN BRUIT DE « COUINEMENT » AU MOMENT DU SÉCHAGE COUIC DEUXIÈME ÉTAPE : Installation de la protection de bord de porte 2a ALIGNER UTILISER UNIQUEMENT LE CÔTÉ MOU DU MAILLET DE CAOUTCHOUC DÉCOUPER LE GABARIT AUX PAGES 4 ET 7, PUIS L’AJUSTER AUTOUR DE LA POIGNÉE DE PORTE. ALIGNER L’ONGLET POUR QU’IL AFFLEURE LE BORD DE LA PORTE. FIXER LE GABARIT SUR LA PORTE AVEC DU RUBAN-CACHE. ALIGNER L’EXTRÉMITÉ SUPÉRIEURE DE LA PROTECTION DE BORD DE PORTE AVEC LA DÉCOUPE SUR LA PARTIE INFÉRIEURE DE L’ONGLET DU GABARIT. 2b EXTÉRIEUR INTÉRIEUR S’ASSURER QUE LA TÊTE DU MAILLET EST PERPENDICULAIRE AU BORD DE PORTE. TENIR LE MAILLET COMME SUR L’ILLUSTRATION. Point de frappe POINT DE DÉPART MAINTENIR EN PLACE LA PROTECTION DE BORD DE PORTE AVEC LA MAIN ET FRAPPER DIRECTEMENT ET FERMEMENT AU POINT DE FRAPPE NO 1. NUMÉRO DE PIÈCE : VERSION: SOA801P091-XX REV. – A DATE : 11-01-2022 SUBARU OF AMERICA PAGE 2/7 2c ~½ po ~½ po CONTINUER EN FRAPPANT FERMEMENT VERS LE HAUT ENTRE LE POINT DE FRAPPE NO1 ET 4 À ½ PO D’INTERVALLE. S’ASSURER QUE LA PROTECTION DE BORD DE PORTE EST COMPLÈTEMENT ENFONCÉE, PUIS FRAPPER EN REMONTANT VERS LE HAUT DE LA PROTECTION DE BORD DE PORTE. 2d ~1 po BRUIT SOURD RÉPÉTER SUR TOUTES LES PORTES BRUIT SOURD 2c UNE FOIS LA PROTECTION BIEN ENGAGÉE, MARTELER VERS LE HAUT SUR TOUTES LA LONGUEUR. LORSQUE LA PROTECTION EST ENFONCÉE CORRECTEMENT, UN BRUIT SOURD SE FAIT ENTENDRE. DANS LE CAS CONTRAIRE, RECOMMENCER L’ÉTAPE 2c. Dépose du protecteur de bord de porte LA PROTECTION DE BORD DE PORTE EST UN ACCESSOIRE FIXE QUI NE DOIT PAS ÊTRE ENLEVÉ. SI UNE PROTECTION DE PORTE EST RETIRÉE POUR QUELQUE RAISON QUE CE SOIT, ELLE NE POURRA PAS ÊTRE INSTALLÉE DE NOUVEAU. IL FAUDRA ALORS EN UTILISER UNE NOUVELLE. ~½” ~½” EN COMMENÇANT PAR LE HAUT OU LE BAS DU PROTECTEUR DE BORD DE PORTE, FRAPPER LÉGÈREMENT L’OUTIL DE DÉPOSE EN NYLON LE LONG DU BORD DU PROTECTEUR À INTERVALLE DE 1/2 PO EN LE DÉPLAÇANT VERS LE HAUT OU VERS LE BAS JUSQU’À CE LE PROTECTEUR DE BORD DE PORTE SOIT DÉGAGÉ D’ENVIRON 2 PO. RÉPÉTER LA MÊME PROCÉDURE DE L’AUTRE CÔTÉ. DÈS QU’UNE PORTION D’ENVIRON 2 PO DU HAUT ET DU BAS EST DÉGAGÉE, CONTINUER À PROCÉDER PAR MOUVEMENT VERTICAL VERS LE HAUT OU VERS LE BAS SUR TOUTE LA LONGUEUR DU PROTECTEUR JUSQU’À SON RETAIT COMPLET. NUMÉRO DE PIÈCE : SOA801P091-XX VERSION: REV. – A DATE : 11-01-2022 SUBARU OF AMERICA PAGE 3/7 Nº de pièce SOA801T090 Brevet É.-U. no 8,709,180 Directive d’installation au concessionnaire : Pour assurer des dimensions d’impression appropriées, réglez la dimension de page à « Légal » dans l’onglet des propriétés de l’imprimante et « Taille réelle » dans l’onglet des dimensions et du traitement de la page. Vérifier que l’échelle est exacte à 1:1. Dans le cas contraire, régler le photocopieur. Nº de pièce SOA801T090 Brevet É.-U. no 8,709,180 Directive d’installation au concessionnaire : Pour assurer des dimensions d’impression appropriées, réglez la dimension de page à « Légal » dans l’onglet des propriétés de l’imprimante et « Taille réelle » dans l’onglet des dimensions et du traitement de la page. Vérifier que l’échelle est exacte à 1:1. Dans le cas contraire, régler le photocopieur. Gabarits de portes arrière du côté du conducteur : Point de frappe initial MY24 Subaru Impreza / Crosstrek / Crosstrek Wilderness Porte arrière côté conducteur Gabarit de montage de la protection de bord de porte Directive d’installation au concessionnaire : Pour assurer des dimensions d’impression appropriées, réglez la dimension de page à « Légal » dans l’onglet des propriétés de l’imprimante et « Taille réelle » dans l’onglet des dimensions et du traitement de la page. Vérifier que l’échelle est exacte à 1:1. Dans le cas contraire, régler le photocopieur. NUMÉRO DE PIÈCE : SOA801P091-XX VERSION: REV. – A D5TE : 11-01-2022 SUBARU OF AMERICA PAGE 6/7 NUMÉRO DE PIÈCE : SOA801P091-XX TE : SUBARU OF AMERICA PAGE 7/7 Directive d’installation au concessionnaire : Pour assurer des dimensions d’impression appropriées, réglez la dimension de page à « Légal » dans l’onglet des propriétés de l’imprimante et « Taille réelle » dans l’onglet des dimensions et du traitement de la page. Vérifier que l’échelle est exacte à 1:1. Dans le cas contraire, régler le photocopieur. VERSION: REV. – A Gabarits de portes arrière du côté du passager : PPooiinntt ddee ffrraappppee iinniittiiaall MY24 Subaru Impreza / Crosstrek / Crosstrek Wilderness Porte arrière côté passager Gabarit de montage de la protection de bord de porte
**************************************************************************************************************
**************************************************************************************************************
SEOCONTENT-END
