| “This site contains affiliate links for which OEMDTC may be compensated” |
Accessory Installation Guide
| 2024MY Crosstrek (Wilderness Only) – REAR BUMPER COVER | E771SFN100 |
PART NUMBER: E771SFN100
INSTALLATION INSTRUCTIONS
DESCRIPTION: CROSSTREK WILDERNESS REAR BUMPER COVER
PREPARATION: Park vehicle in well lit area. Open rear gate. Unpack parts. Read the entire installation instruction prior to beginning.
STEP 1: Clean any dirt, oil or wax from attaching area of bumper with a clean cloth and rubbing alcohol. Then prepare the surface with the supplied alcohol pads.
STEP 2: Note: If the temperature is below 60°F (15°C), heat the double sided tape and bumper surface to a temperature of 80°F (27°C).
STEP 3: DO NOT REMOVE ANY TAPE AT THIS TIME. Place part on rear bumper and roughly align the rear gate’s latch striker with the center triangle on the part. Then look under the hatch’s weather stripping for molded-in triangles in the rear bumper and align with the outboard triangles on the part. See detailed illustration below. Inspect the gaps on all 4-sides and become familiar with the “home” position of this part.
STEP 4: While part is in the home position locate supplied left and right corner alignment templates. Using the part as a guide position the right then the left templates. Ensure templates are against back vertical wall and aligned with part profile, then tape down outside edges of templates.
STEP 5: Flip part over. Fold and crease the tape liners as shown in the illustration below. You may tape each liner to the top surface of the part (optional).
STEP 6: Reposition part onto rear bumper. Align again following STEP 3 and 4. Ensure each tape liner is positioned properly from STEP 5. Find the “home” position and inspect both sides of the part to ensure proper positioning then firmly hold in place.
STEP 7: While firmly holding the part with your left hand, use your right hand to gently pull the liner shown below by approximately 3″ (76mm) BUT DO NOT PRESS DOWN.
STEP 8: Press down on the part by a finger’s width only at the location shown below. Do not press down anywhere else but now lightly hold the part in place.
STEP 9: Gently pull the liner shown below by approximately 3″ (76mm) BUT DO NOT PRESS DOWN.
STEP 10: Carefully inspect and align (if necessary) the side of the part to the bumper and then press down on the part by a finger’s width only at the location shown below. Do not press down anywhere else.
STEP 11: Carefully and gently remove the entire tape liner section shown below. Pulling with too much force or too quickly can tear the tape liner. TIP: If liner tears, pull the other liner that is intact.
STEP 12: Use a towel and apply firm pressure (approximately 15lb. of force) to the area highlighted in yellow
STEP 13: Gently pull the liner shown below by approximately 3″ (76mm) BUT DO NOT PRESS DOWN.
STEP 14: Press down on the part by a finger’s width only at the location shown below. Do not press down anywhere else.
STEP 15: Gently pull the liner shown below by approximately 3″ (76mm). BUT DO NOT PRESS DOWN
STEP 16: Carefully inspect and align (if necessary) the side of the part to the bumper and then press down on the part by a finger’s width only at the location shown below. Do not press down anywhere else.
STEP 17: Carefully and gently remove the entire tape liner section shown below. Pulling with too much force or too quickly can tear the tape liner. TIP: If liner tears, pull the other liner that is intact.
STEP 18: Use a towel an apply firm pressure (approximately 15lbs. of force)
STEP 19: Carefully and gently remove the entire tape liner section shown below. Pulling with too much force or too quickly can tear the tape liner. TIP: If liner tears, pull the other liner that is intact.
STEP 20: Use a towel an apply firm pressure (approximately 15lbs. of force)
STEP 21: Carefully and gently remove the two tape liner sections shown below. Pulling with too much force or too quickly can tear the tape liner. TIP: If the liner tears, pull the same liner from the opposite direction. Then remove corner alignment templates.
STEP 22: Use a towel and apply firm pressure (approximately 15lbs of force) to the areas highlighted in yellow.
STEP 23: Inspect part for any areas not adhering to the bumper. Firmly pressed down as needed. Done.
E771SFN100
Loading...
Reload document 
Open in new tab
- Genuine Subaru
Rear Bumper Cover - helps protect the upper surface of the painted bumper from scratches and dings.
- Fits 2020-2025 Subaru Outback
- E771SAN100
- Does NOT fit Outback Wilderness Models
- Genuine Subaru Forester Rear Bumper Cover Protector
- E771SSJ000
- 2019-2024 Forester
- Helps protect the upper surface of the painted bumper from scratches and dings.
- Perfect Fit for 2025-2026 Subaru Forester: Specifically designed for the 2025-2026 Subaru Forester, this rear bumper protector ensures a precise and stylish fit, seamlessly blending with your vehicle’s design.
- Quick & Easy Installation: Simply clean the trunk door step, peel off the adhesive backing, and stick it on—no tools required. The strong adhesive ensures a secure and hassle-free installation.
- Scratch & Damage Protection: Shields your rear bumper from scratches, dents, and scuffs caused by loading and unloading items. It also covers existing marks, keeping your car looking new and well-maintained.
- Durable ABS Material: Made from high-quality ABS plastic, this bumper guard is corrosion-resistant, flexible, and long-lasting. It protects your car’s paint while maintaining a sleek appearance.
- 100% Satisfaction Service: At FormiPow, We offer a comprehensive one-year return and exchange policy, ensuring that your purchase is absolutely risk-free. Should you face any issues, don't hesitate to reach out via your Amazon account. We promise a resolution within 24 hours.
- 👍Fitment: Compatible with Subaru Outback 2021 2022 2023 2024 2025 2026
- 👍Install: Installed with 3M Double Sided tape, please ensure the surface is free of dirt and waxes before applying
- 👍Surface: Groove design, textured surface, molded pattern, Made of high quality silicone polymer material.
- 👍Attention: Installed with 3M Double Sided tape, please ensure the surface is free of dirt and waxes before applying
- 👍Function: Custom fit design for maximum coverage damage, Protect car rear bumper when loading or unloading luggages, groceries, tools box and so on
- 【Widely Application】 Exterior Rear Bumper Guard Protector fit for 2019-2024 Subaru Forester. Before place the order, please check the car.
- 【High-Quality Materials】Made of high quality ABS plastic material, which is excellent corrosion resistance and toughness. It can protect your car door panel from wear and tear, will not scratch the original car paint, even if it is frequently scraped, it will not be easily damaged.
- 【Easy Installation】 Wipe the trunk door sill clean and make sure the surface is clean and dry, Tear off the adhesive backing film, grasp the location where it needs to be pasted, stick the protection strip flat on its surface and press it evenly for a few seconds to make sure it is tight.
- 【Multiple Use】Effectively prevent your cars from scratches and damages when loading and unloading luggages, tool box, groceries and more items in car trunk, also can be used to cover existing scratches and stains keep car looks new and clean. Making it more personalized and sporty fashion
- 【Good Service】We care about your feedback,and if there is any issues with our product or service for any reason, do not hesitate to contact us. We will spare no effort to get your satisfaction
- FITMENT - Compatible with 2018-2023 Subaru Crosstrek. Replacement part number: E771SFL100.
- FEATURE - Rear bumper cover protector replacement, provide protection for the upper surface from scratches. Protect the paint and give your vehicle a new appearance.
- MATERIAL - This brand new bumper cover is constructed of heavy duty plastic to ensure a long lasting service life under outdoor conditions, UV-Resistant and Anti-Scratch, preventing scuffs and gouges.
- DESIGN - Custom fit design for maximum coverage damage. Surface design with grooves and textures, non-slip function, preventing the falling of things.
- INSTALLATION - Install with 3M adhesive. Before installing, wipe off the dirty oil and attach it. Carefully place the product in the correct position and press it. Do not wash the car for 24 hours to get good adhesion. Instruction and mounting hardware are NOT included.
- 【Fitment】:Rear Bumper Protector Guard for Subaru Outback 2021 2022 2023 2024
- 【EASY installation】:This rear bumper guard is very durable,flexible,will not crack or break, glue tape is coming under the trim, just stick on sill, easy to install.
- 【HIGH-quality materials】: The rear bumper protector is Made of high quality silicone polymer material. heat /cold resistance, abrasion resistance, anti-aging, waterproof & UV resistance. Hardness 60 (Shore A).
- 【Function】: The car accessories effectively protect car rear bumper when loading or unloading luggages, groceries, tools box and so on, It prevents nasty scratches and provides protection. Also it can be used to cover any existing scratches, paint damage. The fashionable appearance can not only make your car look cool, but also protect your car.
- 【Attention】: Installed with 3M Double Sided tape, please ensure the surface is free of dirt and waxes before applying.
- 【Widely Application】 Exterior Rear Bumper Guard Protector fit for 2025 Subaru Forester. Before place the order, please check the car
- 【High-Quality Materials】Made of high quality ABS plastic material, which is excellent corrosion resistance and toughness. It can protect your car door panel from wear and tear, will not scratch the original car paint, even if it is frequently scraped, it will not be easily damaged
- 【Easy Installation】Wipe the trunk door sill clean and make sure the surface is clean and dry, Tear off the adhesive backing film, grasp the location where it needs to be pasted, stick the protection strip flat on its surface and press it evenly for a few seconds to make sure it is tight
- 【Multiple Use】Effectively prevent your cars from scratches and damages when loading and unloading luggages, tool box, groceries and more items in car trunk, also can be used to cover existing scratches and stains keep car looks new and clean. Making it more personalized and sporty fashion
- 【Good Service】We care about your feedback,and if there is any issues with our product or service for any reason, do not hesitate to contact us. We will spare no effort to get your satisfaction
- Fitment: KUAFU Rear bumper cover will be compatible with 2018-2023 Subaru Crosstrek. Provide extra protection and decoration for your car
- High Performance: Bumper Cover is designed to prevent the tail and rear side of the vehicle from being damaged or scratched during driving, and it can improve the appearance of the rear end of your car, making it look more modern, beautiful, dynamic and durable
- More Durable: Made of plastic, which has higher strength and longer lifespan. The rough-textured surface has good anti-slip and quick drainage properties
- Package Included: You will receive 1 X Rear Bumper Cover shown in pictures. Mounting hardware and instruction not included
- Installation: Easy to install. Before installation, please ensure that the bumper surface is clean and dry
SEOCONTENT-START
PART NUMBER: E771SFN100 ISSUE 01 10-20-2022 SUBARU
OF AMERICA PAGE 1 / 9 PART NUMBER: E771SFN100 Notes: INSTALLATION INSTRUCTIONS DESCRIPTION: CROSSTREK WILDERNESS REAR BUMPER COVER TOOLS REQUIRED: NOTE: • Do not wash the vehicle for 24 hours following installation of bumper cover. • If bumper cover requires cleaning after installation, wipe with a soft cloth or sponge and mild soap and wipe thoroughly with a dry cloth. Do not use gasoline, thinner, acid, alkali or other solvent based products. • The recommended adhesive surface temperature range is: 60°-110°F (15°- 43°C). • If the surface temperature is below 60°F (15°C), heat the double sided tape and bumper surface to a t emperature of 80°F (27°C). • A one-hour cure time is recommended before exposing the vehicle to extreme temperatures (hot or cold). REMARQUE: • Ne pas laver le véhicule pendant 24 heures suivant I’installation du couvre pare-chocs. • Si Ie couvre pare-chocs doit être nettoyé après l’installation, l’essuyer à l’aide d’une éponge ou d’un linge imbibé d’une solution de savon doux puis frotter avec un chiffon sec. Ne pas utilizer d’essence, de diluant, d’acide ou d’alcali ou d’autres prodults à base de solvant. • La plage de température recommandée pour Ia surface adhésive est de 15 à 43°C (60 à 110°F). • Si la température de Ia surface est sous 15°C (60°F), chauffer Ie ruban à double face et la surface du pare-chocs à une température de 27°C (80°F). • Un temps de durcissement d’une heure est recommandé avant d’exposer le véhicule à des températures extrêmes (chaudes ou froid es). Left Template modèle de gauche Right Template modèle droit PART NUMBER: E771SFN100 PREPARATION: Park vehicle in well lit area. Open rear gate. Unpack parts. Read the entire installation instruction prior to beginning. STEP 1: Clean any dirt, oil or wax from attaching area of bumper with a clean cloth and rubbing alcohol. Then prepare the surface with the supplied alcohol pads. STEP 2: Note: If the temperature is below 60°F (15°C), heat the double sided tape and bumper surface to a temperature of 80°F (27°C). PART NUMBER: E771SFN100 ISSUE 01 10-20-2022 SUBARU OF AMERICA PAGE 2 / 9 PART NUMBER: E771SFN100 STEP 3: DO NOT REMOVE ANY TAPE AT THIS TIME. Place part on rear bumper and roughly align the rear gate’s latch striker with the center triangle on the part. Then look under the hatch’s weather stripping for molded-in triangles in the rear bumper and align with the outboard triangles on the part. See detailed illustration below. Inspect the gaps on all 4-sides and become familiar with the “home” position of this part. STEP 4: While part is in the home position locate supplied left and right corner alignment templates. Using the part as a guide position the right then the left templates. Ensure templates are against back vertical wall and aligned with part profile, then tape down outside edges of templates. STEP 5: Flip part over. Fold and crease the tape liners as shown in the illustration below. You may tape each liner to the top surface of the part (optional). PART NUMBER: E771SFN100 ISSUE 01 10-20-2022 SUBARU OF AMERICA PAGE 3 / 9 PART NUMBER: E771SFN100 STEP 6: Reposition part onto rear bumper. Align again following STEP 3 and 4. Ensure each tape liner is positioned properly from STEP 5. Find the “home” position and inspect both sides of the part to ensure proper positioning then firmly hold in place. STEP 7: While firmly holding the part with your left hand, use your right hand to gently pull the liner shown below by approximately 3″ (76mm) BUT DO NOT PRESS DOWN. 3″ (76mm) STEP 8: Press down on the part by a finger’s width only at the location shown below. Do not press down anywhere else but now lightly hold the part in place. Only press here. PART NUMBER: E771SFN100 ISSUE 01 10-20-2022 SUBARU OF AMERICA PAGE 4 / 9 PART NUMBER: E771SFN100 STEP 9: Gently pull the liner shown below by approximately 3″ (76mm) BUT DO NOT PRESS DOWN. 3″ (76mm) STEP 10: Carefully inspect and align (if necessary) the side of the part to the bumper and then press down on the part by a finger’s width only at the location shown below. Do not press down anywhere else. Only press here. STEP 11: Carefully and gently remove the entire tape liner section shown below. Pulling with too much force or too quickly can tear the tape liner. TIP: If liner tears, pull the other liner that is intact. PART NUMBER: E771SFN100 ISSUE 01 10-20-2022 SUBARU OF AMERICA PAGE 5 / 9 PART NUMBER: E771SFN100 STEP 12: Use a towel and apply firm pressure (approximately 15lb. of force) to the area highlighted in yellow STEP 13: Gently pull the liner shown below by approximately 3″ (76mm) BUT DO NOT PRESS DOWN. 3″ (76mm) STEP 14: Press down on the part by a finger’s width only at the location shown below. Do not press down anywhere else. Only press here. PART NUMBER: E771SFN100 ISSUE 01 10-20-2022 SUBARU OF AMERICA PAGE 6 / 9 PART NUMBER: E771SFN100 STEP 15: Gently pull the liner shown below by approximately 3″ (76mm). BUT DO NOT PRESS DOWN 3″ (76mm) STEP 16: Carefully inspect and align (if necessary) the side of the part to the bumper and then press down on the part by a finger’s width only at the location shown below. Do not press down anywhere else. Only press here. STEP 17: Carefully and gently remove the entire tape liner section shown below. Pulling with too much force or too quickly can tear the tape liner. TIP: If liner tears, pull the other liner that is intact. PART NUMBER: E771SFN100 ISSUE 01 10-20-2022 SUBARU OF AMERICA PAGE 7 / 9 STEP 18: Use a towel an apply firm pressure (approximately 15lbs. of force) PART NUMBER: E771SFN100 STEP 19: Carefully and gently remove the entire tape liner section shown below. Pulling with too much force or too quickly can tear the tape liner. TIP: If liner tears, pull the other liner that is intact. STEP 20: Use a towel an apply firm pressure (approximately 15lbs. of force) PART NUMBER: E771SFN100 ISSUE 01 10-20-2022 SUBARU OF AMERICA PAGE 8 / 9 PART NUMBER: E771SFN100 STEP 21: Carefully and gently remove the two tape liner sections shown below. Pulling with too much force or too quickly can tear the tape liner. TIP: If the liner tears, pull the same liner from the opposite direction. Then remove corner alignment templates. STEP 22: Use a towel and apply firm pressure (approximately 15lbs of force) to the areas highlighted in yellow. STEP 23: Inspect part for any areas not adhering to the bumper. Firmly pressed down as needed. Done. PART NUMBER: E771SFN100 ISSUE 01 10-20-2022 SUBARU OF AMERICA PAGE 9 / 9 % 0 50mm 38.5 ‘ ◄ 88.0 ► 17.8 38.5 100 mm Please use the included templates for installation, however if they are damaged or lost, print these templates as a replacement. NOTE: BEFORE PRINTING, CONFIRM PAGE SIZING IS SET TO “ACTUAL SIZE” OR “SET CUSTOM SCALE TO” OR “ZOOM TO 100%. DO NOT SELECT “FIT” OR “SHRINK”. AFTER PRINTING, USE A RULER AND CHECK THE PRINTED SCALE TO CONFIRM MATCH. NUMÉRO DE PIÈCE : E771SFN100 INSTRUCTIONS D’INSTALLATION DESCRIPTION : COUVRE PARE-CHOCS ARRIÈRE CROSSTREK WILDERNESS Left Template modèle de gauche Right Template modèle droit OUTILS REQUIS : Notes: NOTE: • Do not wash the vehicle for 24 hours following installation of bumper cover. • If bumper cover requires cleaning after installation, wipe with a soft cloth or sponge and mild soap and wipe thoroughly with a dry cloth. Do not use gasoline, thinner, acid, alkali or other solvent based products. • The recommended adhesive surface temperature range is: 60°-110°F (15°- 43°C). • If the surface temperature is below 60°F (15°C), heat the double sided tape and bumper surface to a t emperature of 80°F (27°C). • A one-hour cure time is recommended before exposing the vehicle to extreme temperatures (hot or cold). REMARQUE: • Ne pas laver le véhicule pendant 24 heures suivant I’installation du couvre pare-chocs. • Si Ie couvre pare-chocs doit être nettoyé après l’installation, l’essuyer à l’aide d’une éponge ou d’un linge imbibé d’une solution de savon doux puis frotter avec un chiffon sec. Ne pas utilizer d’essence, de diluant, d’acide ou d’alcali ou d’autres prodults à base de solvant. • La plage de température recommandée pour Ia surface adhésive est de 15 à 43°C (60 à 110°F). • Si la température de Ia surface est sous 15°C (60°F), chauffer Ie ruban à double face et la surface du pare-chocs à une température de 27°C (80°F). • Un temps de durcissement d’une heure est recommandé avant d’exposer le véhicule à des températures extrêmes (chaudes ou froid es). NUMÉRO DE PIÈCE : E771SFN100 VERSION 01 10-20-2022 SUBARU OF AMERICA PAGE 1 de 9 NUMÉRO DE PIÈCE : E771SFN100 PRÉPARATION : Garez le véhicule dans une zone bien éclairée. Ouvrez le hayon arrière. Déballez les pièces. Lisez l’ensemble de la notice de montage avant de commencer.. ÉTAPE 1 : Nettoyez les dépôts de poussière, d’huile ou de cire sur la zone de fixation du pare-chocs avec un chiffon propre et de l’alcool dénaturé. Préparez ensuite la surface avec les tampons d’alcool fournis. ÉTAPE 2 : Remarque : Si la température est inférieure à 15 °C (60 °F), chauffez la bande adhésive double-face et la surface du pare-chocs pour atteindre une température de 27 °C (80 °F). PART NUMBER: E771SFN100 VERSION 01 10-20-2022 SUBARU OF AMERICA PAGE 2 de 9 NUMÉRO DE PIÈCE : E771SFN100 ÉTAPE 3 : À CETTE ÉTAPE, NE RETIREZ AUCUNE BANDE ADHÉSIVE. Placez la pièce sur le pare-chocs arrière et alignez approximativement la gâche de verrouillage du hayon arrière avec le triangle situé sur la partie centrale de la pièce. Sous le coupe-froid du hayon, recherchez des triangles moulés dans le pare-chocs arrière et alignez-les avec les triangles orientés à l’extérieur de la pièce. Voir l’illustration détaillée ci-dessous. Examinez les ouvertures des 4 côtés et familiarisez-vous avec la position d’origine de cette pièce. ÉTAPE 4 : Pendant que la pièce est en position d’origine, repérez les gabarits d’alignement des coins gauche et droit fournis. En utilisant la pièce comme guide, positionnez le gabarit de droite, puis celuide gauche. Assurez-vous que les gabarits sont placés contre le mur vertical arrière et alignés avec le profil de la pièce, puis apposez du ruban adhésif pour coller les bords extérieurs des gabarits. ÉTAPE 5 : Retournez la pièce. Pliez les bandes de revêtement comme dans l’illustration ci-dessous. Vous pouvez coller chaque bande sur la surface supérieure de la pièce (optionnel). PART NUMBER: E771SFN100 VERSION 01 10-20-2022 SUBARU OF AMERICA PAGE 3 de 9 NUMÉRO DE PIÈCE : E771SFN100 ÉTAPE 6 : Repositionnez la pièce sur le pare-chocs arrière. Refaites l’alignement en suivant les ÉTAPES 3 et 4. Assurez-vous que chaque bande de revêtement est bien positionnée, comme à l’ÉTAPE 5. Trouvez la position d’origine et examinez les deux côtés de la pièce pour assurer son bon positionnement, puis maintenez fermement la pièce en place. ÉTAPE 7 : Tout en maintenant fermement la pièce avec votre main gauche, utilisez la main droite pour tirer doucement sur la bande comme ci-dessous sur environ 76 mm (3 pouces), MAIS N’APPUYEZ PAS. 76 mm (3 pouces) ÉTAPE 7 : Tout en maintenant fermement la pièce avec votre main gauche, utilisez la main droite pour tirer doucement sur la bande comme ci-dessous sur environ 76 mm (3 pouces), MAIS N’APPUYEZ PAS. . Appuyez exclusivement à cet endroit PART NUMBER: E771SFN100 VERSION 01 10-20-2022 SUBARU OF AMERICA PAGE 4 de 9 NUMÉRO DE PIÈCE : E771SFN100 ÉTAPE 9 : Tirez doucement sur la bande comme illustré ci-dessous, sur environ 76 mm (3 pouces), MAIS N’APPUYEZ PAS. 76 mm (3 pouces) ÉTAPE 10 : Inspectez soigneusement et alignez (si nécessaire) le côté de la pièce avec le pare-chocs, puis appuyez sur la pièce avec un doigt, exclusivement à l’emplacement indiquéci-dessous. N’appuyez nulle part ailleurs. Appuyez exclusivement à cet endroit. ÉTAPE 11 : Procédez avec précaution pour enlever la bande de revêtement, comme indiqué ci-dessous. Tirer trop fort ou trop rapidement peut déchirer la bande de revêtement. CONSEIL : Si la première bande se déchire, tirez sur l’autre bande qui est intacte. PART NUMBER: E771SFN100 VERSION 01 10-20-2022 SUBARU OF AMERICA PAGE 5 de 9 NUMÉRO DE PIÈCE : E771SFN100 ÉTAPE 12 : Utilisez une serviette et appliquez une pression ferme (avec une force d’environ 7 kg) sur la zone en surbrillance jaune ÉTAPE 13 : Tirez doucement sur la bande comme illustré ci-dessous, sur environ 76 mm (3 pouces), MAIS N’APPUYEZ PAS. 76 mm (3 pouces) ÉTAPE 14 : Appuyez sur la pièce avec un seul doigt, exclusivement à l’emplacement indiqué ci-dessous. N’appuyez nulle part ailleurs. Appuyez exclusivement à cet endroit. PART NUMBER: E771SFN100 VERSION 01 10-20-2022 SUBARU OF AMERICA PAGE 6 de 9 NUMÉRO DE PIÈCE : E771SFN100 ÉTAPE 15 : Tirez doucement sur la bande comme illustré ci-dessous, sur environ 76 mm (3 pouces). N’APPUYEZ PAS 76 mm (3 pouces) ÉTAPE 16 : Inspectez soigneusement et alignez (si nécessaire) le côté de la pièce avec le pare-chocs, puis appuyez sur la pièce avec un doigt, exclusivement à l’emplacement indiqué ci-dessous. N’appuyez nulle part ailleurs. Appuyez exclusivement à cet endroit. ÉTAPE 17 : Procédez avec précaution pour enlever la bande de revêtement, comme indiqué ci-dessous. Tirer trop fort ou trop rapidement peut déchirer la bande de revêtement. CONSEIL : Si la première bande se déchire, tirez sur l’autre bande qui est intacte. PART NUMBER: E771SFN100 VERSION 01 10-20-2022 SUBARU OF AMERICA PAGE 7 de 9 NUMÉRO DE PIÈCE : E771SFN100 ÉTAPE 18 : Utilisez une serviette et appliquez une pression ferme (avec une force d’environ 7 kg) ÉTAPE 19 : Procédez avec précaution pour enlever la bande de revêtement, comme indiqué ci-dessous. Tirer trop fort ou trop rapidement peut déchirer la bande de revêtement. CONSEIL : Si la première bande se déchire, tirez sur l’autre bande qui est intacte. ÉTAPE 20 : Utilisez une serviette et appliquez une pression ferme (avec une force d’environ 7 kg) PART NUMBER: E771SFN100 VERSION 01 10-20-2022 SUBARU OF AMERICA PAGE 8 de 9 NUMÉRO DE PIÈCE : E771SFN100 ÉTAPE 21 : Procédez avec précaution pour enlever les deux bandes de revêtement, comme indiqué ci-dessous. Tirer trop fort ou trop rapidement peut déchirer la bande de revêtement. CONSEIL : Si le revêtement se déchire, tirez la même bande de revêtement dans la direction opposée. Ensuite, enlevez les gabarits d’alignement des coins. ÉTAPE 22 : Utilisez une serviette et appliquez une pression ferme (avec une force d’environ 7 kg) sur les zones en surbrillance jaune. ÉTAPE 23 : Inspectez la pièce pour vérifier que toutes les zones adhèrent au pare-chocs. Appuyez fermement, au besoin. Vous avez terminé. PART NUMBER: E771SFN100 VERSION 01 10-20-2022 SUBARU OF AMERICA PAGE 9 de 9 ◄ 88,0 ► 50mm ◄ 88,0 ► 100 mm Veuillez utiliser les gabarits inclus pour !’installation. Si vous les perdez ou les endommagez, imprimez ces gabarits en guise de remplacement. REMARQUE : AVANT L’IMPRESSION, CONFIRMEZ QUE LE DIMENSIONNEMENT DE LA PAGE EST REGLE A« TAILLE REELLE » OU « REGLER L’ECHELLE PERSONNALISEE A» OU « ZOOM A 100 % ». NE SELECTIONNEZ PAS « AJUSTER » OU « RETRECIR ». APRES L’IMPRESSION, MESUREZ L’ECHELLE IMPRIMEE A L’AIDE D’UNE REGLE POUR CONFIRMER LA CORRESPONDANCE.
SEOCONTENT-END
Last update on 2025-04-17 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.
