Wireless Charger (Key Start) – 2024 Subaru Impreza & Crosstrek

SEOCONTENT-START

1 △ 01 WIRELESS CHARGER CROSSTREK (2024MY and after) INSTALLATION INSTRUCTION IMPREZA (2024MY and after) PART No. H1010FN210 IMPORTANT 1. The installation should be carried out by an authorized Subaru dealer. 2. Pay special attention not to damage vehicle components when removing / installing them. 3. Route the wiring so that it cannot be abraded against any sharp edges. 4. Refer to the vehicle service manual. 5. Check that the vehicle’s electronic devices are operating normally. Be sure to make note of the contents of the memory of electronic devices such as the preprogrammed radio channels. ATTENTION • Please disconnect the battery cable while conducting wiring operations. Failure to do so may result in electrical shock or injury. • make an note of data in the memory of the electrical components such as the radio. This will help avoid problems that may arise when performing the repair check after the installation. • When tightening bolts or screws, use the proper tools and the proper size, and comply for Failure to securely tighten the bolt and nut may cause them to loosen and fall off, causing damage. • When removing the connector from the vehicle, remember to remove the lock that holds the main body of the connector, instead of pulling the lead line. This protects against a lead wire cuts, etc. • Please be sure to properly connect the connector and terminal. This helps to avoid a poor connection. • When wiring the harness(wiring), clamp the wires together along with the wiring harness of the vehicle. This protects the harness from becoming entangled or causing strange sounds. • – ful not to let the harness be hooked or pulled from the back. This protects against a cut wire or shorts. • Be careful not to forcefully pull the wiring harness of the vehicle. This helps prevent the connector from being disconnected, and the wires from being cut or damaged. • After installing the wiring, perform an operations check on the newly installed parts before reassembling. This helps prevent mis-wiring. O+~SUBARU m n ~ … cg~ Please confirm that the electrical components of the vehicle operate normally. Also, please w~it ~ H~’ <~ the specified torque specified for the part. ‘ ..- •,l::P~ – 1~ ~ ~ £t • When connecting or disconnecting parts or installing or removing the finisher, etc, be care —.c. ~ ~ ~ 2 ① ② No. Name Qty ① Wireless charger 1 ② Operation Manual 1 COMPONENTS TOOLS ・ Driver (-) ・ Masking tape 1. Before Starting Work (1) Before unpacking, check that the key specifications on the package are the same as those on the vehicle. (2) Securely apply the parking brake and set the select lever to N. 1-1. Removing Battery Terminals Disconnect the ground terminal from the battery sensor and wait at least 60 seconds before starting work. Follow the latest service manual instructions for removing and installing the negative (ground) battery terminal. CAUTION I I I I 0 • FOR KEY START VEHICLES ONLY [ 3 (A) C22 C22(W):x2 (Fig. 1) (Fig. 3) (Fig. 2) (Fig. 4) 2. Installing Wireless Charger 2-1. Removal of Related Parts (1) Insert a flat-head screwdriver or similar tool with protective tape wrapped around the (A) section of the tray assembly center LWR. (Fig. 1) (2) Remove the clip joints and hooks first. Then remove the tray assembly center LWR. (Fig. 2) (3) Pull out the existing wireless charger harness on the vehicle side and remove the vinyl tape holding the harness in place. (Fig. 3) (4) Route the vehicle harness as shown in the figure. (Fig. 4) To prevent damage to vehicle parts, apply protective tape to the tool before use. CAUTION Vinyl tape Harness Harness fixation point Harness length from harness fixation point: Approx. 375 mm – …. -.—,,,_ … , ,~,, ,,, ,_,.., . _ ~ 4 (5) Check that the key specifications on the label on the back of the wireless charger match the vehicle key specifications. (Fig. 5) (6) Securely attach the power connector (8-pole connector) to the terminal of the wireless charger. (Fig. 6) (7) Install the wireless charger. (Fig. 7) *The removed tray ASSY center LWR is not used. Return it to the customer. When installing the wireless charger, make sure that the surrounding parts do not bite the harness. CAUTION (Fig. 6) (Fig. 5) (Fig. 7) . . ~ i~I ~ ( 0 , > – ~,-j- – °t [ )-~ ,[ r: For Key Start vehicles only 5 2. Operation Check (1) Connect the battery. (2) Check that the wireless charger is compatible with the vehicle key specifications. Follow the flowchart below to perform the check. Do the vehicle key specifications match the key specifications on the package and the label on the back of the wireless charger? Start The wireless charger specifications must match the vehicle key specifications. No Yes Turn the engine switch to ACC and turn on the wireless charger. No Yes Does the indicator on the wireless charger light up green? Place a mobile device compatible with wireless charging in the charging area of the wireless charger to perform charging. End (3) Start the engine (or the hybrid system) and check that the wireless charger operates properly. (4) Set the clock and settings for audio system, etc.and complete the procedure by cleaning the vehicle. △ Contents Creation date Revised history △ 00 △ 01 Newly created Added procedure for IMPREZA Feb. 1, 2023 Mar. 1, 2023

SEOCONTENT-END