“This site contains affiliate links for which OEMDTC may be compensated” |
NHTSA ID Number: 10234845
Manufacturer Communication Number: 1212711R
Summary
If you encounter a customer complaint of a white residue build up on the rear door partition glass or interior molding, it may be crystallized salt.
NUMBER: 12-127-11R
DATE: 05/26/11
REVISED: 05/22/13
APPLICABILITY: | 2010MY and Later Legacy & Outback |
SUBJECT: | White Residue on Rear Door Partition Glass Molding |
INTRODUCTION
If you encounter a customer complaint of a white residue build up on the rear door partition glass or interior molding, it may be crystallized salt. Normally, the condition will occur during the winter months in states that use salt or similar mineral based anti-icing agents on their streets and highways.
Under certain conditions, exterior water that enters the molding, and would normally drain away, may be drawn up into the interior of the partition glass molding where it will evaporate and leave trace mineral deposits behind. An additional seal rib was added to the inside lip of the molding to prevent any exterior water from moving to the inside of the molding.
COUNTERMEASURE IN PRODUCTION
A second countermeasure to the molding was incorporated into production starting with VIN D*029921 (Legacy) and D*271303 (Outback).
PART INFORMATION
MODEL | PART NAME | NEW PART NUMBER | NOTE |
Legacy | WSTR Partition R RH | 62284AJ00C | 2nd
Countermeasure |
WSTR Partition R LH | 62284AJ01C | ||
Outback | WSTR Partition R RH | 62284AJ02D | |
WSTR Partition R LH | 62284AJ03D |
SERVICE PROCEDURE/INFORMATION
Refer to the applicable Subaru Service Manual for additional information and torque specifications when performing the following steps:
1) Remove the rear door trim.
2) Partially remove the sealing cover to gain access to the door sash hardware.
3) Remove the upper screw and two bolts which secure the door sash, then remove sash.
4) Remove the partition glass/molding from window frame.
5) Remove the partition molding from the partition glass.
Note: Make sure the glass is free of dirt and grease prior to installing the new molding.
6) Install new partition molding to partition glass in the following order.
7) Install partition glass/molding in window frame. Note: Liquid water based soap can be applied to the outer edge of the partition molding to ease installation.
8) Install hardware, sash, sealing cover and door trim in reverse order of removal.
14 Affected Products
Vehicle
MAKE | MODEL | YEAR |
SUBARU | LEGACY | 2010-2023 |
1 Associated Document
Manufacturer Communications
NUMBER: 12-127-11R
DATE: 05/26/11
REVISED: 05/22/13
https://www.nhtsa.gov/recalls?nhtsaId=10234845
- Compatible to OEM#: 91112SG140, 91112SG141, 91112SG142, 91112-SG140, 91112-SG141, 91112-SG142
- Compatible to Other Part#: SU1505100
- Campatibility: Use the "Amazonconfirmedfit" to check if this parts fits for your car. Or match the OEM part number if you know your original one. You can also send us the car information to confirm compatibility, we'll respond within 24 hrs.
- Warranty: We offer 1-year warranty on all our products! Warranty is for REPLACEMENT of the parts only. Warranty does not cover shipping, labor, towing, rentals, storage, legal fees, lost wages or any other incidental fees.
- Communication: Please send us message for any questions. If you are not satisfied with our product or service, please contact us before you write any review. We will be more than happy to assist you.
- Lifetime warranty
- Made in the USA
- 100% paint match guarantee
- Quick and easy no-drill installation with the use of self-adhering 3M Tape
- Added protection against shopping carts, door dings, scratches, chipping, and other road hazards
- Lifetime warranty
- Made in the USA
- 100% paint match guarantee
- Quick and easy no-drill installation with the use of self-adhering 3M Tape
- Added protection against shopping carts, door dings, scratches, chipping, and other road hazards
- Universal Automotive Rubber Reveal Moldings
- with Clean-Stick butyl
- Marcy's moldings will not fade, crack, or shrink
- High quality materials - Very flexible
- 【Flexible】Our car windshield seal strip is made of upgraded EPDM (rubber), which is soft, elastic and highly flexible, with no odor. Wear-resistant and durable, not easy to age and break, can be used in any weather.
- 【Sound Proof】 The rubber seal strip trim has strong sealing properties, which can effectively isolate the penetration of rain and dust. It can also block external noise, effectively reduce the noise inside and outside the car, and make your driving environment more comfortable and quiet.
- 【Self Adhesive】This sunroof seal strip adopts a perfect arc design, which can effectively fit the edge of the window and have a good sealing effect. The self-adhesive design on the back makes installation simple and convenient, and can be easily completed by one person. Please wipe clean the installation area and gaps before installation.
- 【Free Cutting】Our rubber sealing strips are available in three sizes: 9.84Ft/3m, 16.5Ft/5m, and 23Ft/7m. They have strong adhesion and are not easy to fall off. You can freely DIY cut according to the required length. You can use a hair dryer to heat it before use.
- 【Multifunctional】Our rubber sheets with adhesive are suitable for various car models. They can be used on the front and rear windshields, sunroofs, rear triangle windows, etc. They can also be used on various sliding windows, wardrobe doors, sliding doors, Security doors, etc.
- 【Quality Material】: These car seals are made of high quality rubber material, good elasticity and toughness, easy to fold and bend, it has excellent characteristics such as heat resistance, aging resistance, corrosion resistance, acid and alkali resistance. The seals are odorless, safe and non-toxic, strong and durable.
- 【T-Shape Design】: This car seal with T-shaped design can better fit the windows and body, seal the gap space between the windows and body, front windshield, rear windshield, sunroof and frame. Prevent air leakage, prevent the entry of cold air from outside the car, and maintain a comfortable temperature inside the car.
- 【Strong Adhesive】: These car seals are self-adhesive, high strength adhesive adhesion is very good, strong tensile strength, good elasticity, long-term use does not crack, not deformed. And the adhesive backing is strong, firmly pasted, no degumming, tearing off the car noise isolation strip will not leave sticky residue.
- 【Easy Installation】: The car seal is easy to install, the car window rubber seal uses self-adhesive installation method, no need to drill holes, you just need to wipe the place clean with a cloth, make sure the surface is clean and flat, take off the red adhesive film, press it on the edge of the window, then cut the strip and stick it firmly.
- 【Widely Used】: This rubber sealing decorative strip is widely applicable, not only has the practical function of sealing the car door, but also can well decorate the car, can well fit most of the models on the market, including cars, trucks, SUVs and various other models, the sealing strip can be applied to the car door, body, car hood, front and rear windshield and other locations.
- Element '03-06
- Genuine OEM
- Direct fit
- Genuine Honda Parts 73150-SCV-A01 Front Windshield Molding
- High-quality material: The car front windshield strip is made of EPDM rubber material, which has good elasticity and toughness, easy to fold and bend, safe and non-toxic, durable and sturdy, more flexible, resistant to high temperature and cold. The sealing effect is good and can be used for a long time.
- Car weatherstrip: The T-shaped design of the weatherstrip can better fit your windows and body, sealing the gap between the window and body, front windshield, rear windshield, sunroof, frame gap. Prevent dust, water leakage, air leakage, reduce noise, make the car quieter and more comfortable.
- Easy installation: 1. Wipe with a cloth and keep the clean surface dry. 2. Tear off the red adhesive film, stick it where you need it, and cut the tape. 3. Try not to wash the car within 3 days to ensure stickiness. In winter, when the temperature is low, you can use a hair dryer to make it stick more firmly.
- Specifications: Width: 19MM/0.75 inches. We also have 14MM/0.55inch, two sizes of width for you to choose; different areas require different widths. See our description on the picture. Length: 10Ft, you can arbitrarily DIY cut the length you need to suit your car.
- Features: soft, high elasticity, smooth surface, anti-ultraviolet, environmentally friendly material, less odor, no harm to human body, suitable for various rounded corners and radii. If you are not satisfied with our products or have any suggestions, please contact us immediately, we will reply you within 24 hours.
- Premium Body Molding: Enhance the appearance and safeguard your vehicle with Cowles Products' professional automotive body molding trim.
- Easy Installation: Our body molding is designed for hassle-free installation, allowing you to quickly and effortlessly upgrade your car, truck, or SUV.
- Style & Protection: Enjoy the benefits of both style and protection. Our premium body molding not only adds a sleek and polished look to your vehicle but also safeguards it against minor dents and scratches.
- Customizable Length: Trim or cut the body molding to your desired length, ensuring a perfect fit for your specific vehicle.
- Secure Attachment: With the help of durable 3M Tape, our premium body molding securely attaches to your vehicle, providing long-lasting adhesion and peace of mind.
Last update on 2024-04-18 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.
SEOCONTENT-START
Bulletin Number: 12-127-11R; Date: 05/22/11 Page 1
APPLICABILITY: 2010MY and Later Legacy & Outback
SUBJECT: White Residue on Rear Door
Partition Glass Molding NUMBER: 12-127-11R DATE: 05/26/11 REVISED: 05/22/13
CAUTION: VEHICLE SERVICING PERFORMED BY UNTRAINED PERSONS COULD RESULT IN SERIOUS INJURY TO THOSE PERSONS OR TO OTHERS.
Subaru Service Bulletins are intended for use by professional technicians ONLY. They are written to inform those technicians of conditions that may occur in some vehicles, or to provide information that could assist in the proper servicing of the vehicle. Properly trained technicians have the equipment, tools, safety instructions, and know-how to do the job correctly and safely. If a condition is described, DO NOT assume that this Service Bulletin applies to your vehicle, or that your vehicle will have that condition.
SUBARU OF AMERICA, INC. IS “ISO 14001 COMPLIANT”
The international standard for excellence in Environmental Management Systems. Please recycle or dispose of automotive products in a manner that is friendly to our environment and in accordance with all local, state and federal laws and regulations.
INTRODUCTION
If you encounter a customer complaint of a white residue build up on the rear door partition glass or interior molding, it may be crystallized salt. Normally, the condition will occur during the winter months in states that use salt or similar mineral based anti-icing agents on their streets and highways.
Under certain conditions, exterior water that enters the molding, and would normally drain away, may be drawn up into the interior of the partition glass molding where it will evaporate and leave trace mineral deposits behind. An additional seal rib was added to the inside lip of the molding to prevent any exterior water from moving to the inside of the molding.
COUNTERMEASURE IN PRODUCTION
A second countermeasure to the molding was incorporated into production starting with VIN D*029921 (Legacy) and D*271303 (Outback).
PART INFORMATION MODEL PART NAME NEW PART NUMBER NOTE
Legacy
WSTR Partition R RH WSTR Partition R LH WSTR Partition R RH
62284AJ00C
62284AJ01C
62284AJ02D 2nd re
Outback WSTR Partition R LH 62284AJ03D
Continued on next page…
SERVICE BULLETIN
ATTENTION:
GENERAL MANAGER 0
PARTS MANAGER 0
CLAIMS PERSONNEL 0
SERVICE MANAGER 0
IMPORTANT – All
Service Personnel Should Read and Initial in the box
provided, right. Bulletin Number: 12-127-11R; Date: 05/22/11 Page 2
SERVICE PROCEDURE/INFORMATION
Refer to the applicable Subaru Service Manual for additional information and torque
specifications when performing the following steps:
1) Remove the rear door trim.
2) Partially remove the sealing cover to gain access to the door sash hardware.
3) Remove the upper screw and two bolts which secure the door sash, then remove sash.
4) Remove the partition glass/molding from window frame.
5) Remove the partition molding from the partition glass. Note: Make sure the glass is free of dirt and grease prior to installing the new molding. 6) Install new partition molding to partition glass in the following order.
1
2
3
4
Legacy
1
2
3
4
Outback
7) Install partition glass/molding in window frame. Note: Liquid water based soap can be applied to the outer edge of the partition molding to ease installation.
8) Install hardware, sash, sealing cover and door trim in reverse order of removal. WARRANTY/CLAIM INFORMATION
For vehicles within the Basic New Car Limited Warranty period, refer to the Subaru Labor Time Guide available on Subarunet for claim coding information.
**************************************************************************************************************
**************************************************************************************************************
SEOCONTENT-END