| “This site contains affiliate links for which OEMDTC may be compensated” |
Accessory Installation Guide
| 2025MY Forester (All trims) – Side Sill Plates – Front
E101SSL000 |
E101SSL000 |
INSTALLATION INSTRUCTIONS
PART NUMBER: E101SSL000 / E101SSL020
DESCRIPTION:
Side Sill Plate Kit Forester
PREPARATION – BEFORE INSTALLATION:
1. This product should be installed with proper installation tools.
2. Install this product while observing all warnings and precautions stated in this instruction booklet.
3. VERY IMPORTANT: Thoroughly wash vehicle with Soap and Water.
4. Parts storage should be flat at room temperature and in a clean dry place. Care should be taken to avoid a dusty environment.
Notes to the Installer
1. Read the entire installation instructions prior to beginning the installation of the accessory.
2. Ensure that the vehicle is properly protected in the area that the accessory is to be installed.
3. To prevent vehicle damage, never place tools on top of painted surfaces, seats, dash pad, console or floor carpet / mat.
4. Always wear appropriate safety gear to include gloves and eye protection when required.
1
Alcohol
Thoroughly wash vehicle with a soft lint-free cloth. Wipe front sill area where the Sill Plate will be installed with alcohol wipes. Allow the area to dry completely.
2
Dry Fit
Place masking tape along lines of plastic panel, following the edge downward. Locate Sill Plate into place using the diagram shown above.
NOTE: Sill Plate should remain on flat surface only, not on radius.
3
Separate Liner
Remove liner from Sill Plate. After removal of part liner, to prevent contamination, limit touching adhesive side of Sill Plate by handling on the edges.
4
Sill Plate Alignment
Start by aligning the edge of Sill Plate with the tape as shown. Make sure the top edge of the Sill Plate is aligned with the plastic panel and lay into position.
NOTE: If mislocated, lift straight up and reposition into correct location.
5
Adhere To Surface
Remove masking tape. Starting in the center, squeegee the top surface of the Sill Plate onto the surface of sill area as shown, using firm, overlapping squeegee strokes.
*(Repeat Steps 1-5 for right side of vehicle.)
Care and Cleaning
Wash side sill plates with warm soapy water as needed, (do not use other chemical based cleaners).
Visual Check
Make sure all edges are firmly adhered.
E101SSL000
https://static.oemdtc.com/AccessoryInstallationGuide/E101SSL000.pdf
Loading...
Reload document 
Open in new tab
- Genuine Subaru Forester Side Sill Plate kit
- E101SSJ020
- Add some protection and dress up the front sill plates . Side sill plates for Forester Wilderness feature a matte black finish. Set of two.
- 2022-2024 Forester ( wilderness)
- Genuine Subaru Side Sill Plates Kit
- E101SFL102
- Handsome, metallic finished panels dress up the sill plates of the Crosstrek. SET OF 4
- 2018 2019 2020 2021 2022 2023 2024 Crosstrek
- Genuine Subaru IMPREZA Side Sill Plate Kit
- E101SFL002
- These Genuine Subaru Side Sill Plates Kit will add some Handsome, metallic finished panels that will protect and dress up the sill plates of the Impreza.
- 2017-2024 IMPREZA
- GENUINE SUBARU not aftermarket
- Genuine OEM
- Replaces existing sill plates
- Performance look
- 2018 Subaru Crosstrek
- 【Custom Mold for Crosstrek】Compatible for Subaru Crosstrek 2018-2024, door Sill Protector is Designed According to the Original Car Data, fit Perfectly with the Car Door Frame.
- 【High-Quality Material】Door sill scuff protector adopts Leather material that are dirt and wear resistant to protect your car door frame.No worrying about car paint scratches anymore!
- 【Practical】These Door Entry Guard protect your truck by protecting the door sill from being scraped and dirty. Also it can be used to cover any existing scratches.It also easy to clean. Whether it is dust or dirt, cleaning the surface with a brush rag slightly, it will become new immediately.
- 【Easy to Install】Simply tear off the label at the back of door sill scuff plate to reveal the sticker and attach it to the threshold of the car.Design of the protectors includes the logo of the car model,which perfectly matches with your car.
- 【Package Includes】4*Outer Door Sill (2pcs For Front Door, 2 pcs For Back Door)
- Genuine Subaru part that fits your specific vehicle
- Side Sill Plates
- Part Number: E101SFL001
- Manufactured to meet specifications for fit, form, and function
- CUSTOM FIT - License plate bracket is suitable for following vehicle models: Subaru 2000-2023. Save money on fines! Bracket size (6" x 12") fits US & Canada license plates & won't cover license plate or registration sticker.100% street legal
- HIGHEST QUALITY - The license tag holder is made of premium & heavy-duty plastic, which is totally rust-proof, anti-wear, & corrosion-resistant. The metal license plate doesn't directly contact the car paint surface, so it won't lead to scratches!
- KIT INCLUDES- 6 secure screw bolts. Bracket has 4 mounting holes, one in each corner to hold plate secured. May require drilling holes in bumper if existing holes far apart from each other. NO EXTRA TOOLS REQUIRED! Wrench is included w every bracket!
- EASY TO INSTALL- Align License Plate Bracket to Existing holes on car bumper and attach bracket with 2 long screws. Attach your License Plate to a Mounting Bracket using 4 small screws. Wrench is Included for Your Convenience & Easy Installation!
- BEST EXPERIENCE - We are committed to providing customers with premium-quality automotive accessories to suit all their needs. This is why we always use non-toxic materials of the highest quality & produce all goods according to GMP standards.
- lluminated side sill plates
- H461SFN200
- 2024 Crosstrek
- Illuminated side sill plates feature the Crosstrek logo in bright white lighting to add an attractive accent to the door sills
- Lighting is activated when the door is opened and turns off when the door is closed
- ★ Anti-collision Wear-resistant: This invisible protective film can protect the door sill against scratching. Protects mirrors from scratches and scuffs. Protects car doors from bumps knocks without marks. Protects front and rear bumpers from scratches. Peel off the transparent film, no residual adhesive. Can be freely cut.
- ★ Transparent Protective Film: Made of transparent nano-glue material, highly transparent and non-discoloring. It is waterproof, scratch resistant, abrasion resistant, high temperature resistant and anti-aging. These door edge guards will protect door edges from scratches, chips and scuffs.
- ★ Universal Size: 2in x 33ft and 2.8in x 33ft. 2 sizes available. This car door transparent seal strip is very durable, flexible, and bendable, glue tape is coming under the trim, just stick on the car door.
- ★ Universal Accessories: Door sill scuff, Front Spoiler, Rear Spoiler, Trunk Spoiler Protecton, Side Skirt Guard, DIY protection and decoration not only for your car, but also for your Home.
- ★ Easy to Install : Conforms well to most contours andshapes. Self-adhesive air pocket release backing design so there are no bubbles. Select the appropriate size according to the installation location.
Last update on 2024-06-08 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.
SEOCONTENT-START
1. Front Side Sill Plate (2)
2. Squeegee 3. Alcohol Wipes ess.
steps complete the
Denotes quality processes to be checked prior to moving to the next step.
Denotes safety equipment required to be used such as a mask, goggles, rubber gloves, and hearing protection.
Denotes cautions to be taken to avoid physical injury or electronic component damage.
Denotes warnings that may lead to serious physical injury or vehicle damage.
Denotes specific tools that are
to complete the step. Denotes cautions to be taken to avoid vehicle and component damage. Mask
Goggles
Rubber Gloves Hearing Protection ISSUE 00 DATE SUBARU OF AMERICA PAGE 1/06
PART NUMBER: E101SSL000 / E101SSL020
DESCRIPTION:
Side Sill Plate Kit Forester KIT CONTENTS: nt Side Sill Plate (2). 2. Sque
TOOLS REQUIRED:
MEANING OF CHARACTERS:
DESCRIPTION
Side Sill Plate
Soft lint-free Microfiber Cloth
Masking Tape Scissors 3. Alcohol Wipes PREPARATION – BEFORE INSTALLATION: 1. This product should be installed with proper installation tools. 2. Install this product while observing all warnings and precautions stated in this instruction booklet. 3. VERY IMPORTANT: Thoroughly wash vehicle with Soap and Water. 4. Parts storage should be flat at room temperature and in a clean dry place. Care should be taken to avoid a dusty environment. Notes to the Installer 1. Read the entire installation instructions prior to beginning the installation of the accessory. 2. Ensure that the vehicle is properly protected in the area that the accessory is to be installed. 3. To prevent vehicle damage, never place tools on top of painted surfaces, seats, dash pad, console or floor carpet / mat. 4. Always wear appropriate safety gear to include gloves and eye protection when required. Left Front Door Sill Left Front Door Sill Plastic Panel Plastic Panel Masking Tape 1 Alcohol
Thoroughly wash vehicle with a soft lint-free cloth. Wipe front sill area where the Sill Plate will be installed with
alcohol wipes. Allow the area to dry completely. 2 Dry Fit
Place masking tape along lines of plastic panel, following the edge downward. Locate Sill Plate into place using the diagram shown above.
NOTE: Sill Plate should remain on flat surface only, not on radius. Sill Plate Adhesive side of Sill Plate Left Front Door Sill Liner
Plastic Panel Masking Tape 3 Separate Liner 4
Remove liner from Sill Plate. After removal of part liner, to prevent contamination, limit touching adhesive side of Sill Plate by handling on the edges. Sill Plate Alignment
Start by aligning the edge of Sill Plate with the tape as shown. Make sure the top edge of the Sill Plate is aligned with the plastic panel and lay into position.
NOTE: If mislocated, lift straight up and reposition into correct location. DESCRIPTION
Side Sill Plate ISSUE 00 DATE 9/18/23 SUBARU OF AMERICA PAGE 2/06 Left Front Door Sill Plastic Panel 5 Adhere To Surface
Remove masking tape. Starting in the center, squeegee the top surface of the Sill Plate onto the surface of sill area as shown, using firm, overlapping squeegee strokes. * (Repeat Steps 1-5 for right side of vehicle.) Care and Cleaning Items to be Checked Results of the Check Wash side sill plates with warm soapy water as needed, (do not use other chemical based cleaners). Visual Check Items to be Checked Results of the Check Make sure all edges are firmly adhered. DESCRIPTION
Side Sill Plate ISSUE 00 DATE 9/18/23 SUBARU OF AMERICA PAGE 3/06 IINSTRUCTIONS D’INSTALLATION NUMÉRO DE PIÈCE : E101SSL000 / E101SSL020
DESCRIPTION :
Kit plaque de bas de marche Forester CONTENU DE LA TROUSSE :
1. Enjoliveur de seuil de porte latérale avant (2).
3. Lingette imbibée d’alcool 2. Racloir 1. Enjoliveur de seuil de porte latérale avant (2) 2. Racloir 3. Lingettes imbibées d’alcool OUTILS REQUIS: Linge en microfibre doux et non pelucheux Ruban-cache Ciseaux SIGNIFICATION DES SYMBOLES: Indique les avertissements de possibilité de blessure grave ou de dommages
au véhicule. Indique les vérifications de qualité à effectuer avant de passer à la prochaine étape. Indique l’équipement de sécurité requis et devant être utilisé, comme un masque, des lunettes de sécurité, des gants en caoutchouc et des dispositifs de protection antibruit. Indique les précautions à prendre pour éviter les blessures ou les dommages aux composants électroniques. Indique les outils nécessaires pour compléter une étape. Masque Lunettes de sécurité Indique les précautions à prendre pour éviter les dommages au véhicule
et aux composants. Indique la marche à suivre pour compléter le processus. Gants en caoutchouc Dispositif de protection antibruit DESCRIPTION
Enjoliveur de seuil de porte latérale VERSION 00 DATE 9/18/23 SUBARU OF AMERICA PAGE 4/06 PRÉPARATION – AVANT L’INSTALLATION: 1. Ce produit doit être installé avec les outils d’installation adéquats. 2. Lors de l’installation du produit, respecter tous les avertissements et prendre toutes les précautions énoncées dans le livret d’instructions. 3. TRÈS IMPORTANT : Laver le véhicule soigneusement avec de l’eau et du savon. 4. Les pièces doivent être entreposées à plat et à température ambiante dans un endroit propre et sec. Il faut veiller à éviter tout environnement poussiéreux. Remarques à l’intention de l’installateur 1. Lire le livret d’instructions en entier avant de commencer l’installation de l’accessoire. 2. S’assurer que la surface du véhicule où sera posé l’accessoire est bien protégée. 3. Pour éviter tout dommage au véhicule, ne jamais poser d’outils sur les surfaces peintes, les sièges, le dessus du tableau de bord, la console ou les tapis et la protection du plancher. 4. Toujours porter de l’équipement de sécurité approprié, dont les gants et les lunettes protectrices lorsque cela est requis. Seuil de porte avant gauche Seuil de porte avant gauche Panneau de plastique Panneau de plastique Ruban de masquage 1 Alcool
Laver le véhicule soigneusement avec un linge doux et non pelucheux. Essuyer la surface du seuil de porte avant, là où l’enjoliveur sera posé, avec des lingettes imbibées d’alcool. Laisser la surface sécher complètement. 2 Installation à sec
Placez du ruban de masquage le long des lignes du panneau en plastique, en suivant le bord vers le bas. Localisez la plaque de seuil en place à l’aide du schéma ci-dessus.
REMARQUE : L’enjoliveur de seuil doit reposer sur une surface plate et non incurvée. Enjoliveur de seuil de porte Côté adhésif de l’enjoliveur de seuil de porte Seuil de porte avant gauche Revêtement Panneau de plastique Ruban de masquage 3 Enlèvement de la pellicule protectrice
Enlever la pellicule protectrice de l’enjoliveur de seuil de porte. Pour prévenir toute contamination après avoir enlevé la pellicule, éviter de toucher au côté adhésif de l’enjoliveur de seuil de porte en le tenant par les côtés. 4 Alignement de l’enjoliveur de seuil de porte
Commencez par aligner le bord de la plaque de seuil avec le ruban adhésif, comme indiqué. Assurez-vous que le bord supérieur de la plaque de seuil est aligné avec le panneau en plastique et mis en place.
REMARQUE : En cas de mauvais positionnement, lever fermement le gabarit en ligne droite et le replacer. DESCRIPTION
Enjoliveur de seuil de porte latérale VERSION 00 DATE 9/18/23 SUBARU OF AMERICA PAGE 5/06 Résultats de la vérification
Nettoyage et entretien Éléments à vérifier
Vérification visuelle
Au besoin, nettoyer les enjoliveurs de seuil
de porte latérale avec de l’eau tiède savonneuse (ne pas utiliser de produits de nettoyage chimiques).
Vérifier que tous les bords sont bien collés.
DATE
SUBARU OF AMERICA
AGE
00
5 Adhésion à la surface
Retirez le ruban de masquage. En commençant par le centre, raclez la surface supérieure de la plaque de seuil sur la surface du seuil, comme illustré, en utilisant des coups de raclette fermes
et superposés.
DESCRIPTION
Enjoliveur de seuil de porte latérale
* (Répéter les étapes 1 à 5 sur le côté droit du véhicule.)
Seuil de porte avant gauche
Panneau de plastique
VERSION
/23
**************************************************************************************************************
**************************************************************************************************************
SEOCONTENT-END
