| “This site contains affiliate links for which OEMDTC may be compensated” |
NHTSA ID Number: 10080548
Manufacturer Communication Number: 02-158-14R
Summary
THIS SERVICE INFORMATION BULLETIN ANNOUNCES CHANGES TO THE COMPONENT PARTS OF THE ACCESSORY DRIVE BELT TENSIONER ASSEMBLY USED ON 3.6L H-6 ENGINES. THESE DESIGN CHANGES WILL INCREASE THE RIGIDITY OF THE TENSIONER ASSEMBLY WHILE IMPROVING PRODUCTION EFFICIENCY.
NUMBER: 02-158-14R
DATE: 11/21/14
REVISED: 01/09/15
| APPLICABILITY: | 2015MY Legacy & Outback Models with 3.6L Engine |
| SUBJECT: | Accessory Drive Belt Tensioner Component Changes |
INTRODUCTION
This Service Information bulletin announces changes to the component parts of the accessory drive belt tensioner assembly used on 3.6L H-6 engines. These design changes will increase the rigidity of the tensioner assembly while improving production efficiency.
COUNTERMEASURE IN PRODUCTION
The new accessory belt tensioner components were incorporated into production on July 18, 2014 starting with Engine Number: 552158.
PART INFORMATION
| PART NUMBER | DESCRIPTION |
|---|---|
| 13086AA200 | BRKT- TENSIONER |
| 13082AA020 | STOPPER- BELT ADJ |
| 13063AA020 | WASH- BELT ADJ |
| 800110670 | BOLT- 10 X 70 X 70 |
SERVICE PROCEDURE / INFORMATION
When repairing or replacing the belt tensioner or its component parts, follow the procedures outlined in the applicable Service Manual.
**VERY IMPORTANT: If any of the four belt tensioner components described in this bulletin require replacement, ALL FOUR PARTS MUST BE REPLACED AS A SET as they cannot be mixed and matched.
REMINDER: SOA strongly discourages the printing and/or local storage of service information as previously released information and electronic publications may be updated at any time. Always refer to STIS for the latest service information before performing any repairs.
2 Affected Products
Vehicles
| MAKE | MODEL | YEAR |
| SUBARU | LEGACY | 2015 |
| SUBARU | OUTBACK | 2015 |
1 Associated Document
Service Bulletin Document
NUMBER: 02-158-14R
DATE: 11/21/14
REVISED: 01/09/15
https://www.nhtsa.gov/recalls?nhtsaId=10080548
SB-10080548-0699.pdf 398.262KB
Loading...
Reload document 
Open in new tab
NHTSA ID Number: 10233045
Manufacturer Communication Number: 0215814
Summary
Accessory Drive Belt Tensioner Component Changes
1 Associated Document
Manufacturer Communications
NUMBER: 02-158-14
DATE: 11/21/14
https://www.nhtsa.gov/recalls?nhtsaId=10233045
MC-10233045-9999.pdf 401.516KB
Loading...
- OTC's Belt Tension Gauge is designed to allow you to properly check belt tension on drive belts
- Correct tension ensures maximum belt and bearing life
- Easy to read dual scale reads 30-180 lbs. (2.5-15 ft. lbs.) and 130-800 Newtons
- High-grade materials ensure quality performance over the lifetime of the tool
- For use with belts on cars, trucks, SUVs, and motorcycles
- Single-barrel tension tester for use with small V-belts and synchronous belts
- Maximum deflection force of 30 lb.
- Ensures proper belt tension for increased life of drive belt
- Country Of Origin: United States
- Practical: The ABN Belt Tension Gauge helps to set accurate vehicle belt tension
- Versatile: Works with all belt drive models with a 10-pound specification
- Scale: This gauge includes a scale for easy measurement
- L-Pad: Designed with an L-shaped pad that fits all belt sizes
- Ideal Use: Typically for after wheel service or belt replacement/adjustment
- Scale reads in pounds and kilograms
- Measures tension from 30 to 160 lb., and 15 to 75 kg.
- Die-cast aluminum body, nylon indicator arm and pressure pad
- Fits in pocket with stainless steel pocket clip
- Note: Not for use on timing belts
- Indicates tension on all V-belt drives (3L, 4L, 5L, A, B, C, AX, BX, CX, 3V, 5V, 8V)
- Compact, spring loaded design
- Easy to operate; instructions included
- Adjustable for 10" to 170" belt span and up to 35 pounds of tension
- proper tensioning is necessary to avoid premature belt wear
- APPLICATION - When you install a new set of belts, use the gauge to establish correct tension. Then, to maintain performance, re-check belt tension after 24-48 hours. Suitable for most motorcycles with secondary drive belts and 10 lbs.
- PROLONG BELT LIFE - The belt gauge helps set accurate belt tension and can save the life of your belt by reducing friction when used to correctly tension the belt. Adjust the tension of your belt for optimized power delivery.
- EASY TO USE - The belt tensioning device is lightweight and compact, has accurate markings to help you get an accurate reading and adjust the tension accordingly. And it is small enough to carry in your toolbox and fit under your seat.
- U-SHAPED - The U-shaped cradle makes it extremely easy to hold the belt in place while adjusting the belt. We have a small and large movable O-ring to help you mark and read the tension level easily.
- UNIVERSAL - Our Universal Belt Tension Gauge can be used on any vehicle, ATV or motorcycle with a secondary drive belt and a 10lb specification.
- Bright green pressure pad and indicator arm
- Calibrated to measure tension from 100 to 320 lb., and 50 to 150 kg.
- Measure belts up to eight ribs in width
- Note: Not for use on timing belts
- 【Fast And Accurate Hitting Measurements】: Our belt tension gauges are clearly marked with easy to read markings to help you quickly, easily, and accurately measure belt tension to aid in your vehicle adjustments and extend the life of your belts.
- 【Easy To Use】: Place the small O on top of the 10 lb mark and rest the U shaped bracket at a 90° angle against the bottom of the belt, position the large O- to the reference point and record the reading. Then push up on the rubber bumper until the small O touches the bottom of the tool body, then reposition the large O to the reference point, and the difference in the reading is the belt deflection.
- 【U Bracket】: This universal belt tension gauge has a universal U bracket designed to hold the belt firmly in place while you adjust the tension, helping to reduce friction when tensioning the belt properly to extend the life of the belt.
- 【Universal Belt Tensioner】: This belt tension in gauge can be used on any vehicle, ATV or motorcycle with an auxiliary transfer belt and a 10 lb. weight, etc. Ideal for motorcycle belt replacement, adjustment or repair.
- 【We Care About You】: Satisfying every customer is our service tenet, if you have more questions about our belt tension tool or encounter difficulties in the shopping process, please feel to contact us and we will respond to you within 24 hours on business days.
- Item Package Dimension: 5.0399999948592L x 1.3799999985924W x 1.0599999989188H inches
- Item Package Weight - 0.03968320716 Pounds
- Item Package Quantity - 1
- Product Type - ELECTROMECHANICAL GAUGE
- 【Applications】:The 10 lb specification Belt Tension Gauge can works with all 10-pound specification belt drive models,is a very versatile motorcycle belt tension tool.
- 【Easy to Use】:The gauge includes a scale for easy to read and measure.Tt can help you get an accurate reading and adjust the tension accordingly.
- 【Must Have Tool】:Suitable for after belt replacement, adjustment or wheel service.With a compact design, you can put it in your toolbox or under your seat,convenient and space saving.
- 【Smart Design】:Designed with an U-shaped pad that fits all belt sizes,it can securely hold the belt in place while you adjust the tension.6.5 inches long ensures accurate wheel tension measurement in confined spaces and easy placement.
- 【Excellent Service】:Our universal design belt tension gauge 6 months warranty service,if you have any problems, please feel free to contact us.
Last update on 2024-04-01 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.