“This site contains affiliate links for which OEMDTC may be compensated” |
Accessory Installation Guide
Ascent Front Bumper Under Guard | E551SXC000 |
|
Installation Instructions French
INSTALLATION INSTRUCTIONS
PART NUMBER: E551SXC000
DESCRIPTION: ASCENT FRONT BUMPER UNDER GUARD
This section covers installation of the front bumper under guard.
Note:
- Before performing installation, be sure to read this Manual. Perform installation properly in accordance with the instructions.
CAUTION
- Please refer to the precautions below before beginning work, in order to install this product safely and accurately. Please also refer to the vehicle Service Manual.
- During installation, take care not to scratch the car body with tools, etc.
- Before starting installation, switch the engine OFF and ensure the parking brake is set.
- The double-sided tape will stick only if pressed. Also, the adhesiveness of the tape will decrease markedly if it is removed and affixed again. To avoid having to reposition the tape, affix it after determining its proper position.
- Once affixed, the double-sided tape gradually increases in adhesiveness.
- Avoid washing the car for 24 hours after installing the product.
- When the car must be washed or waxed on the same day that installation was performed, wait for at least once hour before beginning, and use tape or other material to cover the areas where double-sided tape is affixed, to prevent contact with water.
- Also take care to not place unreasonable force on installed parts.
- When performing air blowing after installing the product, keep the blower exhaust opening to at least 300 mm away from the parts. Moving the blower too close may cause parts to detach.
- During installation, take care to avoid breakage or warping of car body parts. Refer to your
car’s service manual regarding installation procedures for car body parts.
Preparations
For safe and proper installation, park the vehicle in a flat location and set the parking brake.
Use a neutral detergent (or cleaning agent) and shop cloth to wipe the front bumper guard installation surfaces free of dirt, and let the surfaces dry thoroughly.
Use a shop cloth to clean off any sand or mud on the bumper as well.
Surface Preparation
1
Make sure that all installation surfaces (shown below) are clean, free of dirt, grease, and debris. Use a supplied isopropyl alcohol based wipe (3). Inspect vehicle for damage before installation of front bumper under guard. Before beginning, vehicle and under guard must be at room temperature. If the temperature is below 60 F (16 C) or above 110 F (43 C), let vehicle sit indoors until the bumper and under guard are room temperature.
Front Molding Installation
2
Note position of (3) tape liners with tabs on Front Bumper Under Guard. Use making tape to hold tape leaders to A- surface.
3
Prior to installing Under Guard, remove factory installed rivets in (3) locations indicated.
NOTE: The center rivet may be discarded. Retain the two outboard rivets for reinstallation. (See Step 11)
4
Position Front Bumper Under Guard (1) by aligning the rear edge of the Under Guard to the edge of the bumper. Make sure tape tabs are accessible.
5
Install one Push In Fastener (3) through slot in center underside of part and into vehicle.
6
Install two Ratchet Fasteners (2) through slots in left and right underside of part and into vehicle.
7
Reach behind factory splash guard to insert inner Ratchet Fastener. NOTE: To position the upper half of the rivet, the installer needs to push up on the plastic engine under cover and pull down on the bumper. Reinstall two rivets removed in Step 3.
8
Verify position of part. Holding part in place, expose tape adhesive on top flange by pulling tape tab from end position to end of part.
9
Pull tape tabs on two lower flanges.
10
Lift up on top inner edge of bumper fascia to ensure tape adheres to bumper. Press into place, applying 30 psi of pressure for a minimum of 10 seconds. Repeat application of pressure to all remaining tape locations to ensure adhesion. Allow 24 hours for maximum bond.
11
Re-install the outer (2) rivets removed in Step 3.
12
Installation complete.
ISSUE
00
DATE
01-08-2018
E551SXC000
ASCENT FRONT BUMPER UNDER GUARD
https://static.oemdtc.com/AccessoryInstallationGuide/E551SXC000.pdf
SEOCONTENT-START
INSTRUCTIONS D’INSTALLATION
NUMÉRO DE PIÈCE : E551SXC000
DESCRIPTION : ÉCRAN INFÉRIEUR DE PARE-CHOCS AVANT
CONTENU DE LA TROUSSE :
1.
Écran inférieur de pare-chocs avant (1)
2.
Cheville d’assemblage à crans x2
3.
Cheville d’assemblage à pression x1
4.
Tampon imbibé d’alcool
Lingette imbibée d’alcool (2)
OUTILS REQUIS
Linge d’atelier
Détergent neutre (ou agent de nettoyage)
Pinces à becs fins
Cette section décrit la procédure d’installation de l’écran inférieur du pare-chocs avant.
Remarque :
– Assurez-vous de lire ce manuel avant d’effectuer l’installation. Effectuez l’installation adéquatement, conformément aux directives.
MISE EN GARDE
– Veuillez vous référer aux précautions ci-après avant d’entreprendre les travaux, afin d’installer le produit de façon sécuritaire et adéquate. Veuillez également consulter le manuel d’entretien du véhicule.
– Lors de l’installation, prenez soin de ne pas rayer la carrosserie avec des outils, etc.
– Avant de commencer l’installation, coupez le moteur et assurez-vous que le frein de stationnement est serré.
– Le ruban adhésif double-face collera uniquement si pressé. De plus, le ruban adhésif colle nettement moins bien s’il est retiré et apposé de nouveau. Pour éviter d’avoir à repositionner le ruban, apposez-le après avoir déterminé sa position appropriée.
– Une fois le ruban adhésif double face apposé, son adhésivité augmentera graduellement.
– Évitez de laver le véhicule au cours des 24 heures suivant l’installation du produit.
– Si le véhicule doit être lavé ou ciré le même jour que l’installation, attendez au moins une heure avant de commencer et utilisez du ruban ou d’autres matériaux pour recouvrir les endroits où du ruban adhésif double-face a été apposé afin d’éviter tout contact avec l’eau.
– Faites également très attention de ne pas exercer une force excessive sur les pièces installées.
– Lors du soufflage après l’installation du produit, maintenez l’ouverture du ventilateur à au moins 300 mm des pièces. Placer le ventilateur trop près pourrait faire en sorte que les pièces se détachent.
– Lors de l’installation, prenez garde à ne pas endommager ou déformer les pièces de la carrosserie. Reportez-vous au manuel d’entretien de votre véhicule pour connaître les procédures d’installation des pièces de carrosserie.
Préparations
Pour une installation sécuritaire et adéquate, garez le véhicule à un emplacement plat et serrez le frein de stationnement.
Utilisez du détergent neutre (ou un agent de nettoyage) et un linge d’atelier pour nettoyer toute saleté sur les surfaces d’installation de l’écran du pare-chocs avant et laissez les surfaces sécher complètement.
Utilisez un linge d’atelier pour faire disparaître toute trace de sable ou de boue sur le pare-chocs également.
SIGNIFICATION DES SYMBOLES
: Retirer
: Couple de serrage
: Installer
: Desserrer
: Déconnecter
: Jeter
: Connecter
: Emplacement de l’attache ou de la vis
: Réutiliser
Préparation de la surface
1
Assurez-vous que les surfaces de montage (montrées ci-dessous) sont propres, sans tache, graisse ou résidu. Utilisez la lingette imbibée d’alcool isopropylique fournie (3). Inspectez le véhicule pour déceler toute trace de dommage avant de poser l’écran inférieur de pare-chocs avant. Avant de commencer, veillez à ce que le véhicule et l’écran inférieur soient à la température ambiante. Si la température est inférieure à 16 °C (60 °F) ou supérieure à 43 °C (110 °F), laissez le véhicule reposer à l’intérieur jusqu’à ce que le pare-chocs et l’écran inférieur soient tous deux à température ambiante.
Laver la zone
Tampon imbibé d’alcool
Zone du tampon imbibé d’alcool
Installation de la moulure avant
2
Notez l’emplacement des chemises de ruban adhésif avec languettes (3) sur l’écran inférieur de pare-chocs avant.
Utilisez du ruban-cache pour maintenir les bandes de tirage sur la surface A.
3
Avant d’installer l’écran inférieur, retirez les rivets installés en usine des (3) emplacements indiqués.
REMARQUE : Vous pouvez jeter le rivet du centre. Conservez les deux rivets extérieurs pour l’installation. (voir l’étape 11)
Emplacement des rivets
4
Pour installer l’écran inférieur de pare-chocs avant (1), alignez son rebord à celui du pare-chocs. Veillez à ce que les languettes demeurent accessibles.
5
Posez une cheville d’assemblage à pression (3) dans la fente pratiquée au centre de la pièce, jusque dans le véhicule.
6
Posez deux chevilles d’assemblage à crans (2) dans les fentes pratiquées dans les cotés inférieurs de gauche et de droite de la pièce, jusque dans le véhicule.
7
Passez la main derrière le pare-boue installé en usine pour insérer la cheville d’assemblage à crans intérieure. REMARQUE : Pour mettre en place la moitié supérieure du rivet, l’installateur doit pousser l’écran protecteur inférieur du moteur vers le haut et tirer le pare-chocs vers le bas.
Réinstallez les deux rivets retirés pendant l’étape 3.
Pare-chocs avant
Cheville d’assemblage à crans intérieure
Écran protecteur inférieur du moteur installé en usine
Pousser vers le bas
Cheville d’assemblage à crans extérieure
Pousser vers le haut
Coupe transversale de l’installation des chevilles d’assemblage à crans
REMARQUE : Vous devriez utiliser des pinces à becs fins pour favoriser un assemblage adéquat.
Écran de pare-chocs avant
8
Vérifiez la position de la pièce. En maintenant la pièce en place, tirez la languette du ruban de la position d’extrémité à l’extrémité de la pièce pour exposer l’adhésif du ruban sur la bride supérieure.
9
Tirez les languettes du ruban sur les deux brides inférieures.
REMARQUE : Assurez-vous que les deux trous extérieurs sont alignés avant de tirer sur les bandes de tirage du ruban.
10
Soulevez le rebord intérieur supérieur du carénage arrière pour vous assurer que le ruban adhère au pare-chocs. Pressez la pièce en position en exerçant une pression de 30 psi pendant au moins dix secondes. Appuyez à tous les emplacements restants où se trouve du ruban adhésif pour veiller à ce qu’il soit collé. Prévoyez 24 heures pour obtenir une adhérence maximum.
11
Réinstallez les (2) rivets extérieurs retirés pendant l’étape 3.
12
L’installation est terminée.
SEOCONTENT-END
E551SXC000
ÉCRAN INFÉRIEUR DE PARE-CHOCS AVANT
https://techinfo.subaru.com/stis/doc/accInstallGuide/E551SXC000%20Subaru%20FBUG_French-1-29-18-2.pdf
https://static.oemdtc.com/AccessoryInstallationGuide/E551SXC000F.pdf
“This site contains affiliate links for which OEMDTC may be compensated” |
- 【Fitment】:Rear Bumper Protector Guard for Subaru Outback 2021 2022 2023 2024
- 【EASY installation】:This rear bumper guard is very durable,flexible,will not crack or break, glue tape is coming under the trim, just stick on sill, easy to install.
- 【HIGH-quality materials】: The rear bumper protector is Made of high quality silicone polymer material. heat /cold resistance, abrasion resistance, anti-aging, waterproof & UV resistance. Hardness 60 (Shore A).
- 【Function】: The car accessories effectively protect car rear bumper when loading or unloading luggages, groceries, tools box and so on, It prevents nasty scratches and provides protection. Also it can be used to cover any existing scratches, paint damage. The fashionable appearance can not only make your car look cool, but also protect your car.
- 【Attention】: Installed with 3M Double Sided tape, please ensure the surface is free of dirt and waxes before applying.
- Genuine OEM
- Provide excellent lower body protection
- Accent the vehicle styling
- 2017-2018 Forester 2.5I
- FITMENT - Compatible with 2018-2023 Subaru Crosstrek. Replacement part number: E771SFL100.
- FEATURE - Rear bumper cover protector replacement, provide protection for the upper surface from scratches. Protect the paint and give your vehicle a new appearance.
- MATERIAL - This brand new bumper cover is constructed of heavy duty plastic to ensure a long lasting service life under outdoor conditions, UV-Resistant and Anti-Scratch, preventing scuffs and gouges.
- DESIGN - Custom fit design for maximum coverage damage. Surface design with grooves and textures, non-slip function, preventing the falling of things.
- INSTALLATION - Install with 3M adhesive. Before installing, wipe off the dirty oil and attach it. Carefully place the product in the correct position and press it. Do not wash the car for 24 hours to get good adhesion. Instruction and mounting hardware are NOT included.
- Genuine Subaru Rear Bumper Protector
- E101EAJ501
- Ascent Forester Legacy Outback Forester Wrx Impreza Sti Crosstrek Solterra BRZ
- 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017 2018 2019 2020 2021 2022 2023 2024 Subaru
- Helps protect top surface of rear bumper when loading or unloading cargo area. (Not Compatible with Cargo Tray)
- Other Names:Splash Guard Retainer Clip, Inner Cover Clip, Splash Shield Front Clip, Closing Plate Clip, Under Cover Front Clip, Lower Shield Front Clip, Protector Clip, Closure Panel Clip, Bumper Cover Upper Clip, Lower Grille Clip, Lower Shield Clip, Front Shield Clip, Lower Shield Rear Clip, Air Guide Clip, Lower Cover Retainer Clip, Spoiler Fastener, Under Cover Fastener, Wheelhouse Liner Retainer, Bumper Cover Fastener, Lower Cover Clip,Side Retainer Clip, Side Bracket Clip
- Meet or Exceed OEM Specification. Black Nylon Head Diameter: 18mm Stem Length: 15mm Fits Into 10mm Hole
- Replaces Nissan: 01553-09241 Fits: Nissan: 240SX, 350Z, 370Z, Altima, Cube, Kicks, Maxima, Murano, Pathfinder, Quest, Rogue, Rogue Select, Rogue Sport, Sentra, Titan, Titan XD, Versa
- Fits: Infiniti: FX35, FX37, FX45, FX50, G20, G25, G35, G37, I30, I35, JX35, M35, M35h, M37, M45, M56, Q40, Q45, Q50, Q60, Q70, Q70L, QX30, QX4, QX60, QX70
- Replaces Subaru 57728AC090. Fits Subaru Forester 1998-2019, Impreza 1997 -2003, Legacy 1995-1999 Outback 2000-2003
- Brand New Engine Splash Shield Bolts Hardware Kit Fender Bumper Clips Rivets direct replacement and perfect fitment.Fit Type: Universal
- The extruded U-nuts can be used to replace/fix to the bumper
- The clips are widely used for radiator yoke trim panel door trim door panel bumper car fender flare side skirt grille wheel well air intake engine cover mud flap and splash guard shield retainers rivet clips replacement
- Fits Infiniti G35 G37 FX35 FX45 EX35 Nissan 370Z 350Z (see details)
- Package includes 10pcs Extruded U-nuts - Replace/Fix to the Bumper(CORROSION RESISTANT) 15pcs Body Bolts with Built-in Fender Washer (CORROSION RESISTANT) 10pcs Plastic Push Clips as pictured
- 【Front Bumper Scrape Guard】 Made of light weight & top-grade durable Polyurethane material. Environmentally friendly material and scratch-proof for your car.True lossless installation, stable without glue marks.
- 【Scrape Protector Car】 Application-specific thickening & widening design ensures a perfect fit. Decorate your car charming luxury vivid. Not only effective protection bumper car paint scratch, but also beautiful decoration, good-looking and practical.
- 【Bumper Buddy for Cars】Our front bumper guard comes with attached full adhesive black double-sided tape. The surface provides moderate protection for your bumper against damage caused by any moderate impact.
- 【Proven Reliability from Ultra Adhesive Tapes】Bringing Better Ideas to the Surface through Science and Innovation in ultra tape is a proven alternative to screws, rivets, welds and other forms of mechanical fasteners because of chemically resistant as well as UV and temperature stable.
- 【Universal Size】 The package includes 2 pack bumper scrape guard (15.7*1.7*0.19 inches) and 1 piece of adhesive promoter. Bend freely can fit most car's curvature. It is universally available for most trucks, pickups, SUV or GM.
- FITMENT - Compatible with 2011-2014 Subaru WRX, STI, Impreza (any trim). Please check your vehicle model and year of manufacture.
- FEATURE - Placement on Vehicle: Front, Lower. Color: Silvery. This item is designed to fit most aftermarket headers & oil pan spacers.
- FUNCTION - It can protect your engine better than the old plastic splash plate, and can strengthen your bumper and make your vehicle easier to drive. The oil can be changed easily without removing the entire tray. It keeps the engine compartment temperature low and improves aerodynamics.
- MATERIAL - Made of .063 ALUMINUM(1/16"), only slightly heavier than stock but be more stronger. All holes are laser cut so that it can be directly installed in the corresponding position. Make sure maximum strength and durability for long lasting usage.
- INSTALLATION - No instruction. Installation Accessories are included (As Pictures). Install with screws. In order to install successfully faster, professional installation is highly recommended.
- 👍Fitment: Compatible with Subaru Crosstrek 2024
- 👍Convenient: Textured surface provides slip resistance, installing with 3m Tape quickly and easily
- 👍Material: Made of high quality silicone polymer material, automotive Grade UV-Resistant Durable Black PVC
- 👍Function: Added protection against scuffs, nicks, scratches, and other damaging marks, please feel free to contact us if you have problems
- 👍Slip-resistant: Provide slip resistance, to reduce the damage caused by the falling of the luggage in the suitcase effectively and prevent the items from falling
Last update on 2024-04-17 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.