2020-2022 Subaru Legacy Trunk Spoiler

“This site contains affiliate links for which OEMDTC may be compensated”

Accessory Installation Guide

2020-22MY Legacy – Trunk Spoiler

Note: Please use the correct model year “Accessory Installation Guide Applicability Chart” to reference model line applicability for this document. Not all model year vehicles can be fitted with this accessory.

E721SAN030XX
E721SAN030V3Crystal Black Silica
E721SAN030W7Crystal White Pearl
E721SAN030TRIce Silver Metallic
E721SAN030T1Crimson Red
E721SAN030M4Magnetite Gray
E721SAN030G5Tungsten Metallic
E721SAN030G6Abyss Blue Pearl
E721SAN030Q8Brilliant Bronze Metallic
E721SAN030NNPrimer

 


PART NUMBER: E721SAN030XX

INSTALLATION INSTRUCTIONS

DESCRIPTION: Legacy – Trunk Spoiler

 

TOOLS REQUIRED:

1/4″ Drive Ratchet

1/4″ Drive Torque Wrench

1/4″ Drive 10mm Deep Socket

Power Drill

Spring Loaded Center Punch

Deburring Tool

Flathead Screwdriver

Masking Tape

91% or Greater Isopropyl Alcohol

Rust Preventative or Touch Up Paint

Vacuum

Soft Lint Free Cloths and Large Disposable Cloth

Metric Step Drill

SAE Step Drill Bit

Work Gloves

Safety Glasses

Adjustable Support Rod

Clip Removal Tool

Torsion Bar Tool

 

KIT CONTENTS:

Legacy Spoiler with pre-installed studs

4x 70% Alcohol Pads

4x Compression Nuts

2x Clips

Mylar Template

Left and Right Torsion Bars

 

STEP 1: Clean trunk lid with isopropyl alcohol and a soft clean cloth towel.

 

STEP 2: Open the trunk lid. Using a flat head screwdriver, remove the 12 (twelve) clips and remove the liner.

 

STEP 3: Close trunk. Lay mylar template on trunk lid. Use the two corner arrows to align and center template. Tape template flat to trunk lid.

 

STEP 4: Use a spring loaded center punch to mark all 7 (seven) hole locations.

 

STEP 5: Open trunk lid and lay down a disposable cloth or plastic sheet to protect the trunk area and catch any metal shavings. Remove template and confirm all 7 (seven) punch marks are visible. Close trunk lid.

 

STEP 6 – See STEP 6A if using a metric step drill bit. Skip to 6B if using an SAE step drill bit.

STEP 6A: Metric Hole Drilling: Use tape to mark the stopping position on the step drill bit. Drill the 7 (seven) hole locations according to the sizes as shown below.

STEP 6B – SAE Hole Drilling: Use tape to mark the stopping position on the step drill bit. Drill the 7 (seven) hole locations according to the sizes as shown below.

 

STEP 7: Deburr holes. Vacuum trunk lid. CAUTION: Be careful not to scratch the vehicle’s paint. Open trunk, carefully dispose of cloth or sheet and vacuum trunk area.

 

STEP 8: Use the supplied alcohol wipes to clean the surface of the trunk lid where the spoiler will be installed.

 

STEP 9: Insert the white clips into the trunk lid first. Then line up spoiler but DO NOT press the spoiler down yet.

 

STEP 10: Carefully align the 8mm (5/16”) locating pin and studs with the holes in the trunk lid.

CAUTION: Take extra care with aligning the outboard T-bolts with the white clips from Step 9.

 

STEP 11: When ready, position hands over the RH clip and press down vertically to engage the clips. You will hear a series of clicks. Then proceed to the LH clip and make sure the T-bolt is still aligned with the clip. Press down to engage the clips. You will hear a series of click.

CAUTION: Failure to align the T-bolt to the white clip can cause the white clip to be damaged and pressed into the hole.

 

STEP 12: Open trunk lid and install the 4 (four) compression nuts. Loosely tighten all 4x nuts then torque using the following

Torque: 5.65 +/- 0.40

STEP 12: Open trunk lid and install the 4 (four) compression nuts. Loosely tighten all 4x nuts then torque using the following sequence below.

Torque: 5.65 +/- 0.40 N•m (50 in-lbs +/- 3 in-lbs).

 

STEP 13: Close trunk lid and firmly press down again on locations #1 and #2 to ensure white clips are fully engaged.

 

STEP 14: Clean trunk lid and spoiler.

 

STEP 15: Press the rear seatback lock release button on both ends of the rear seat. Fold seats down.

 

STEP 16: Open the trunk. Start on the right-hand side of the trunk. Turn hook 90º, press tab using a screwdriver and then detach. Use clip remover to remove 4x clips. Save clips for reuse, replace if damaged. Clip Part Number: 99045AE03AMA

 

STEP 17: Repeat for the left-hand side.

 

STEP 18: Locate the Emergency Fuel Door Release Cover on the right-hand side trunk trim panel. Turn knob counter-clockwise and lift up to remove the cover.

 

STEP 19: Move release clip forward and then upward. Tuck it behind the trunk trim panel.

 

STEP 20: Fold and lift up the trunk mat and remove from vehicle.

 

STEP 21: Remove the 2x side spacers and middle trunk subassembly from vehicle.

 

STEP 22: Remove three clips with clip remover (pull towards front of vehicle). Save clips for reuse, replace if damaged. Clip Part Number: 99045AE03AMA. Then lift panel upwards to disengage the four claws (claws are hidden under panel, two are shown in diagram below).

 

STEP 23: Go to the right-hand side of the backseat. Carefully loosen the trunk trim panel from the seat pillar trim and then shift it towards the center of the vehicle (1) to clear the striker and then slightly shift it towards the rear (2).

 

STEP 24: Gently bend the trunk trim panel by the trunk hinge and pull the entire trunk trim panel rearward to remove it from the vehicle. Repeat Steps 23-24 on the opposite side.

 

STEP 25: For vehicles with trunk mounted seatback release handles. Use needle nose pliers to gently squeeze the locking tabs in the release cable mounting clip and remove from bracket.

 

STEP 26: Turn the release handle 90° towards the outside of the vehicle and pull down to remove. Repeat Steps 25-26 on the opposite side.

 

STEP 27: Install the adjustable trunk support rod extending from the spare tire well area to the trunk lid.

WARNING: If the adjustable support rod is not securely installed, the trunk lid can fall when the torsion bars are removed and cause severe injury to the installer and/or damage to the vehicle.

 

STEP 28: Locate the bracket clip at the center of the trunk and open it by releasing the tab in the front and then swinging the bracket rearward to open.

NOTE: Take notice of the order of the torsion bars in the bracket before proceeding.

 

STEP 29: CAUTION: The next few steps must be performed carefully with the specified torsion bar removal tool. Failure to use the proper tool can result in severe injuries and/or damage to the vehicle. Due to this, it is strongly recommended that this product be installed by a SubarueBay retailer.

Left Hand (LH) Torsion Bar Removal: With the special tool securely in place and safety pin engaged, rotate tool downward to apply tension to the LH torsion bar on the right-hand side of the vehicle.

 

STEP 30: While tensioning the LH torsion bar, move the RH hinge link off the LH torsion bar (1). Then carefully unhook the torsion bar off the RH hinge bracket (2) – see diagram (photo taken from rear seat) to lift up and then carefully pull towards the rear. Dislodge torsion bar from the bottom position of the center bracket clip (3).

 

STEP 31: While still holding the torsion bar tool, support the center of torsion bar with other hand and angle it downward (1). Remove torsion bar from the anchor bracket by pulling to the right (2). Remove safety pin and remove the tool from the torsion bar. Dispose of the original torsion bar.

 

STEP 32: Right Hand (RH) Torsion Bar Removal: With the special tool securely in place and safety pin engaged , rotate tool downward to apply tension to the RH torsion bar on the left-hand side of the vehicle (1).

While tensioning the RH torsion bar, move the LH hinge link off the RH torsion bar (2). Then carefully unhook the torsion bar off the LH hinge bracket by lifting up and then carefully pull towards the rear (See figure from Step 30). Dislodge torsion bar from the top position of the center bracket clip – in the center of the trunk (not shown).

 

STEP 33: While still holding the torsion bar tool, support the center of torsion bar with other hand and angle it downward (1). Remove torsion bar from the anchor bracket by pulling to the left (2). Remove safety pin and remove the tool from the torsion bar. Dispose of the original torsion bar.

 

STEP 34: The new accessory torsion bars will have green markings on them. See diagram below for proper engagement of the torsion bar and the safety pin in the tool. Start with the RH torsion bar. Installation of the new torsion bars is the reverse procedure of removal.

Reinstall trunk mounted seatback release handles (if equipped), trunk trim panels, side spacers and middle trunk subassembly, trunk mat, Emergency Fuel Door Release Cable, and Emergency Fuel Door Release Cover, trunk hooks, and return rear seat backs to the upright position and confirm that they are securely engaged.

 

STEP 35: Open and close trunk to confirm proper operation. Then reinstall the trunk liner. Installation complete.

 


2020-22MY Legacy – Trunk Spoiler

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [10.22 MB]

 


 

“This site contains affiliate links for which OEMDTC may be compensated”
Bestseller No. 1
KUAFU Rear Trunk Spoiler Compatible with 2015-2021 Subaru WRX & WRX STI 4 Door Sedan Rear Trunk Lid Spoiler Wing ABS Plastic - Matte Black
  • Fitment: The rear trunk spoiler is compatible with 2015-2021 SubarueBay WRXeBay 4 Door Sedan; compatible with 2015-2021 SubarueBay WRXeBay STIeBay 4 Door Sedan. Please check if this spoiler is suitable for your vehicle before purchasing
  • Superior Material: Made of high quality ABS plastic, wear resistance, stable and reliable, high strength, good impact resistance, not easy to damage, good anti-aging performance. The painted finish provides protection for the surface and improves durability
  • Enhance Performance: The rear trunk spoiler will provide a downward pressure to improve vehicle stability when the vehicle is running. At the same time, it brings a strong sense of impact visually and endows the whole vehicle with a sporty appearance
  • Package Included: 1 x Rear Trunk Spoiler (Matte Black) and mounting hardware. Instructions are NOT included
  • Easy Installation: Direct replacement. Easy and quick to install with screws. You may need some additional drilling
Bestseller No. 2
WheelX Rear Trunk Spoiler Compatible with 2015-2021 Subaru WRX/WRX STI, Duckbill Spoiler Fits for 15-21 4 Door Sedan, High Kick Spoiler Wing Lip (Glossy Black)
  • Rear Trunk Spoiler fits for 2015-2021 SubarueBay WRXeBay / WRXeBay STIeBay 4 Door Sedan Models.
  • Made of high-quality ABS Plastic. Coated with a UV-resistant coat for long-lasting durability.
  • No drilling and cutting required. Heating the double-sided tape further improves the adhesion.
  • Package Included: 1x Rear Spoiler Wing Lip, 2x Double Side Tape.
  • Spoiler Enhance aerodynamics. Give the vehicle a sporty look.
Bestseller No. 3
HECASA Rear Trunk Spoiler Wing Compatible with 2015-2021 Subaru WRX/WRX STI 4 Door Sedan Rear Trunk Lip Wing Matte Black
  • Fitment: Compatible with 2015-2021 SubarueBay WRXeBay 4 Door Sedan; Compatible with 2015-2021 SubarueBay WRXeBay STIeBay 4 Door Sedan.
  • Features: Made of durable ABS plastic, sturdy, impact-resistant and not easily damaged. The surface is black spray paint, waterproof, anti-ultraviolet, can be used outdoors for a long time without fading.
  • Function: Aerodynamic design, increase the downforce, play a certain role in circumventing the flow, and increase the stability of the vehicle when driving. Upgrade the vehicle style to make the vehicle more sporty.
  • Installation: The Trunk Spoiler is mounted with screws, which are more stable and may require additional drilling. Professional installation is recommended.
  • Package: Including 1 X Trunk Spoiler and hardwares for installation. Instructions not included.
Bestseller No. 4
EPARTS-GOGOGO 1 Piece Rear Spoiler Wing Unpainted Black ABS Trunk Lip Spoiler Fit for 2008-2014 Subaru Impreza WRX STI 4 Door Sedan
  • Fit For 2008 - 2014 SubarueBay Impreza WRXeBay STieBay / 2.5i / 2.5GT / Sport 4-Door Sedan Models Only
  • Made of High Quality Light Weight and Durable Material
  • Unpainted Finished; Ready To Be Painted To Match Your Vehicle
  • Gives Your Vehicle Upgrade And Style Look
  • Installation Manual is Not Included, Professional Installation Is Highly Recommend
Bestseller No. 5
Extreme Online Store Replacement for 2015-2021 Subaru STi Models | JDM Performance Style Rear Trunk High Wing Extension Gurney Flap Spoiler (ABS Plastic - Matte Black)
  • Fits All 2015-2021 SubarueBay WRXeBay STieBay Models
  • Package is Included with 1 X SubarueBay WRXeBay STieBay EOS Track Style ABS Plastic - Painted Glossy Black Rear Trunk Wing Gurney Flap Spoiler & 1 X Bag of Hardware
  • Package is Included with 1 X SubarueBay WRXeBay STieBay | JDM Performance Style ABS Plastic - Matte Black Rear Trunk Wing Gurney Flap Spoiler
  • Test Fitted Prior Shipment to Ensure Fitment Issue - Guarantee to Fit.
Bestseller No. 6
HECASA Rear Trunk Spoiler Wing w/Brake Light Compatible with 2002-2007 Subaru Impreza WRX Sedan 4-Door Trunk Lip Spoiler Plastic Painted Glossy Black
  • FITMENT - Compatible with 2002-2007 SubarueBay Impreza WRXeBay Sedan 4-Door. Please confirm the product if it matches your car before you purchase.
  • EXCELLENT PERFORMANCE - This trunk spoiler will reduce the air resistance when facing high speed driving and it will improve the stability of the vehicle. Brake light is very easy to be seen by the car behind, greatly avoiding a rear-end accident.
  • PREMIUM MATERIAL - Made of high quality plastic, which has the advantages of high shock resistance and light weight. The painted surface can adapt to any environment and improve the sporty appearance.
  • EASY INSTALLATION - Instructions are NOT included. Bolt-on installation. Easy to install without drilling or cutting.
  • PACKAGE INCLUDED - 1 x Trunk Spoiler & Brake Light (Glossy Black). Hardware is included.
Bestseller No. 7
IKON MOTORSPORTS, Trunk Spoiler Compatible with 2013-2020 Scion FR-S & Toyota 86 & Subaru BRZ, L Type Carbon Fiber Look PP Rear Tail Lip Deck Boot Wing, 2014 2015 2016 2017 2018 2019
  • Compatible with 2013-2016 Scion FR-S ; 2013-2020 SubarueBay BRZ ; 2017-2020 Toyota 86
  • Material: PP - Polypropylene | Style: L Type | Color: Carbon Fiber Look
  • Package Includes: 1x Trunk Spoiler
  • Instructions NOT included, Professional Installation is Highly Recommended.
  • 30 Days Limited Warranty
Bestseller No. 8
Hyorabyn Black Rear Trunk Spoiler Wing Lip for Subaru WRX STI/Impreza WRX 2015-2021 Trunk Tail Duck Bill Lid ABS Car Accessories
  • 🚗🚗【Fit For】 for SubarueBay WRXeBay STIeBay/Impreza WRXeBay 2015-2021(Please compare our pictures before placing an order)
  • 🚗 🚗【 High Quality】Made of high quality ABS material with 3M tape on the back , ISO 9001 certification to ensure quality.
  • 🚗🚗【Advantage】Protect the original plastic surface and preserve it when resold .
  • 🚗🚗【Easy Installation】 Easy installation with double-sided adhesive tape. Clean the surface and heat the tape before installation will help the cover stick in place better .
  • 🚗🚗【Intimate Customer Service】If you have any quality problems, please don't hesitate to contact us. We will give you a 100% satisfactory solution within 24 hours .
Bestseller No. 9
WheelX Rear Trunk Spoiler Compatible with 2015-2021 Subaru WRX/WRX STI, Fits for 2015 2016 2017 2018 2019 2020 2021 Exterior Tail Deck Lid Wing Lip 4-Door (Carbon Fiber Pattern)
  • Rear Trunk Spoiler Compatible with 2015-2021 SubarueBay WRXeBay / WRXeBay STIeBay 4 Door Sedan All Model.
  • Made of durable ABS plastic, sturdy, impact-resistant and not easily damaged.
  • Rear wing gives your car a sportier and fuller look.
  • Trunk spoiler is screw mounted for stability and may require additional drilling. Professional installation is recommended.
  • The stock rear wing needs to be removed before installation!
Bestseller No. 10
HK5 ABS Plastic OE-Style Painted Blue Rear Trunk Lid Spoiler Wing Compatible with 2022-2025 Subaru WRX STi Sedan
  • Fitment - Fit for 2022-2025 SubarueBay WRXeBay STieBay Sedan Only
  • Design and Material - High Quality ABS Plastic Material Painted Blue
  • Installation - Recommend Professional Installation, Some Slight Modification May be Required
  • Brand new item and never installed before
  • Guarantee - 30-day free return policy - if you have any question about products please feel free to contact us

Last update on 2025-05-08 / Affiliate links / Images from Amazon Product Advertising API


 

This product presentation was made with AAWP plugin.

 


Leave a Comment

Share to...