“This site contains affiliate links for which OEMDTC may be compensated” |
Accessory Installation Guide
2022MY Outback Exterior Graphics – Side Rear Window – Anodized Copper | J121SAN500 |
INSTALLATION INSTRUCTIONS
PART NUMBER: J121SAN500
DESCRIPTION: Exterior Graphics – Side Rear Window
PREPARATION – BEFORE INSTALLATION:
1. This product should be installed with proper installation tools.
2. Install this product while observing all warnings and precautions stated in this instruction booklet.
3. VERY IMPORTANT: Thoroughly wash vehicle with Soap and Water.
4. Parts storage should be flat at room temperature and in a clean dry place. Care should be taken to avoid a dusty environment.
Notes to the Installer
1. Read the entire installation instructions prior to beginning the installation of the accessory.
2. Ensure that the vehicle is properly protected in the area that the accessory is to be installed.
3. To prevent vehicle damage, never place tools on top of painted surfaces, seats, dash pad, console or floor carpet / mat.
4. Always wear appropriate safety gear to include gloves and eye protection when required.
Exterior Graphics – Side Rear Window
1
Alcohol
Thoroughly wash vehicle with a soft lint-free cloth. Wipe the panel where the Exterior Graphic will be installed with alcohol wipes.
Allow the area to dry completely.
2
Dry Fit
Align the Exterior Graphic into position using the handling tabs, door notches and panel edges as references.
3
Separate Liner
Remove liner from Exterior Graphic as shown. To prevent contamination, limit touching adhesive side of the Exterior Graphic by using handling tabs.
4
Spray Vehicle / Adhesive of Exterior Graphic
Spray the adhesive side of the Exterior Graphic with the soap and water solution. Then spray the vehicle surface where the Exterior Graphic will be installed.
5
Exterior Graphic Placement
While using the handling tabs align the Exterior Graphic into position. This allows the part to float on the surface until proper fit is achieved.
6
Spray Exterior Graphic Premask
Spray the top surface of the premask with the soap and water solution. This makes it possible for the squeegee to slide easily across the surface.
7
Squeegee Exterior Graphic
Use caution not to scratch the paint surface with the squeegee.
Using smooth even overlapping strokes squeegee the Exterior Graphic into position.
8
Remove Premask
Carefully remove the premask from the Exterior Graphic by slowly lifting and pulling backward at an 180º angle as shown.
9
Inspect Exterior Graphic
If bubbles are present after premask carrier removal, wrap a towel around the squeegee and carefully attempt to push the bubble to the side of the Exterior Graphic. If the bubble cannot be moved, use a sewing needle to pierce the bubble and press the remaining solution from beneath the Exterior Graphic.
*(Repeat Steps 1-9 for the opposite side of vehicle.)
Care and Cleaning
After an Exterior Graphic installation has been completed, do not high pressure wash the vehicle for 72 hours.
Visual Check
Make sure all edges are firmly adhered.
J121SAN500
2022MY Outback Exterior Graphics – Side Rear Window – Anodized Copper
https://static.oemdtc.com/AccessoryInstallationGuide/J121SAN500.pdf
- Subaru Genuine Exterior Graphics
- J121SAN200
- Exterior Graphics - Side - Anodized Copper
- 2022 2023 2024 Outback Wilderness
- Add a stylish touch to your Outback with graphics for the lower door panels. The Exterior Graphics Kit is constructed of durable PVC film and finished in Anodized Copper to perfectly match the rest of the Wilderness’ bold accents.
- Genuine Exterior Graphics Side Rear Window
- J121SAN500
- 2022 2023 2024 Outback Wilderness
- Add a stylish touch to your Outback with graphics for the side rear windows.
- The Exterior Graphics Kit is constructed of durable PVC film and finished in Anodized Copper to perfectly match the rest of the Wilderness’ bold accents.
- ✔Vinyl Sticker - The sticker material is made of high-quality vinyl. The quality is very good, it is durable, not easy to peel off and fade, and it is waterproof and has good decoration.
- ✔Cool Decoration - The stickers are large in size and can be perfectly stick on your car door side, trunk, etc., to bring different decorations to your car, which is very suitable for people who like to modify and decorate their cars. And it can attract the attention of others.
- ✔How to Install - 1.Wipe off the dust from the car and remove the white bottom paper, 2.Spray a large amount of water (soapy water) on the car and the sticker, 3.Scrape off excess water and air bubbles while installing. (Tip: You can repeatedly lift the sticker and spray water until the sticker fits perfectly.)
- ✔Large Sticker - The large size can better meet the car owners’ modification requirements for the car’s appearance and can perfectly decorate your car. Stickers are very suitable for any type of cars such as SUVs, trucks, and off-road vehicles.
- ✔Come and Buy - The package includes 1pair mountain stickers (left + right), which can decorate your car very well. If you have any questions about the product, you can contact us by email, and we will do our best to solve the problem for you.
- 【High Quality】: These stickers made up of car peaks and pine trees are made of high quality vinyl. They are of very good quality, durable, do not peel or fade easily and are waterproof for a great decorative effect. The car body stickers are large enough to cover the entire door side of the car. Large stickers make your car look more distinctive and cool.
- 【Best Gift】: Car body stickers with mountain and pine tree motifs will not break or fade easily. They are waterproof and extremely sticky, very durable and long lasting. You can give them to your friends, family, loved ones or people who love driving and have a good taste in life, I am sure they will love receiving them.
- 【Easy to Install】: Car body decal mountain range graphic vinyl decals are easy to clean and maintain, easy to install, wipe the dust off the car first, the most important point is that you need to spray more water on one side of the decal, so that you can adjust the position of the decal and eliminate the air bubbles, easy to remove, no marks.
- 【Strong Compatibility】: These body decals with mountain and pine tree motifs are widely available, perfect for car doors or sides, compatible and can be installed on any type of car as they are universal, these decals measure 77.95*16.9* inches and are therefore also ideal for trucks, SUVs, boats, caravans and home decoration.
- 【Beautiful Appearance】: The decal features a stylish long striped mountain peaks full car decal pull pattern that is nearly 2 metres long and will cover your delightful car perfectly, adding a stylish design to your car, greatly decorating your car and giving it a very cool and attractive look, making your car more chic and fun to drive.
- 【High Quality Material】: Made of high-quality materials, it is resistant to cracking, fading, and peeling, and firmly adheres to the surface of your car. Moreover, it is waterproof and will not be damaged in rainy or snowy weather, with a long service life. You can purchase it with confidence.
- 【Self-Adhesive】: There is adhesive on the back, just wipe the dust off the car first, then spray water on the area that needs to be pasted, peel off and paste it. To eliminate bubbles, it is recommended that you lift one of the corners and use a scraper to scrape off excess water and bubbles until they are fully adhered. Please note that do not wash the car or take the highway within 72 hours after pasting the sticker.
- 【Easy Removal】: If you want to remove this sticker from the car body, it is also very simple and easy without damaging the original body or glass. You only need to gently scrape off the edge of the sticker with your nails, completely removing it, and even not damaging the vehicle's paint.
- 【Waterproof】: Adopting waterproof design. You don't have to worry about the sticker getting wet or causing damage if it melts in the rain or ice. Make your car stand out at any time, anywhere.
- 【Wide Application】: This product can be used as an accessory for the rear window, hood, side of the car door, rearview mirror, and other areas of the car. In addition, you can also apply it to real-life scenarios, such as sticking it to windows, mirrors, computers, desktops, or other flat and clean surfaces in a room.
- 【Works for A Long Time】: This forest snow mountain sticker is made of high quality PVC material, not only waterproof and anti-fading, but also not easy to fade very durable. We use a high level of technology to make the laminated layer so that it can carry the different climatic effects of the four seasons.
- 【Easy to Apply】: First wipe off the dust on the car, spray water on the place to be pasted, then put the sticker on the car, lift it from one corner and scrape off the excess water and air bubbles with a scraper until it is completely bonded.
- 【Wide Applications】: This sticker is suitable for any scene. You can use it on cars, car windows, house windows, mirrors, properly primed and painted walls, computers, laptops, notebooks, or many other flat, clean surfaces! You can stick it anywhere on your car, which is perfect for people who like to modify and decorate their cars.
- 【Universal Size】: The universal size of 7×2 inches is suitable for all cars. This size can better meet the modification requirements of car owners for the appearance of the car and can decorate your car perfectly. The stickers are very suitable for any type of car, such as SUVs, trucks, off-road vehicles, etc.
- 【Excellent Customer Service】: The beautiful design of this Forest Snow Mountain car sticker is not only able to show your excellent taste, but also an exquisite gift. If you have any questions, please feel free to contact us, we will reply as soon as possible.
- ✅Compatible with All these Years: 2014, 2015, 2016, 2017, 2018, 2019, 2020. QUALITY – Digitally printed in high resolution, using high quality solvent inks on top quality outdoor vinyl, providing long term durability. The stars and stripes have been precision cut and removed leaving a stunning design.
- ✅Cool Racing Stripe: Attached it to hood or wherever you want to modify can make vehicle look more cool and attractive. That will give your vehicle a fashionable and individualized appearance.
- ✅Easy to Remove: Use nails gently to tear off sticker’s edges and remove them all. No leaving marks or damage to the paint. Stickers can be heated properly by hair dryer, back adhesive will be soft to removed.
- ✅Waterproof and durable: Easy to place on car, car windows, house windows, mirrors, properly primed & painted walls, computers, notebooks, laptops, or many other flat, clean surfaces!
- ✅Strong Adhesive Cover sticker: With strong powerful adhesive at its back, they will hold on your vehicle for a long term, and still work well when rain or car wash.
- ✨【PERFECT FITTING】: Car front rear logo decoration cover ring trim compatible with Subaru Forester 2022-2024. The size of the original car is customized.
- 🚗【EFFECTIVE PROTECTION】: Rear and front badge ring cover is set up to the front hood rear trunk emblem surrounding, protect your front and rear logo panel from anti-rust and abrasion, and improve the monotonous appearance of your original car, make your vehicle cool and high-end luxury looking.
- ✨【PREMIUM MATERIAL】: Rear and front emblems trim ring cover is made of premium ABS material, scratch-resistant and anti-corrosion, lightweight and durability.
- 🚗【EASY INSTALLATION】: Rear front emblems trim ring cover is easy to install and use, Self adhesive design. can installs directly to your car without the need for accessories or tools, Wipe clean your front and rear emblem panel in advance, and press firmly to ensure a good grip of the adhesive.
- ✨【CUSTOMER SERVICE】: 2pcs X rear and front logo trim ring. We offer 12 months Quality Assurance Service. Please feel free to contact us if you have any questions about our product before or after purchase. We will get back to you within 24 hours.
- Funny stickers: Decorate your beloved car with this funny car sticker.
- Sticker composition: The sticker consists of three parts, the first layer is a transparent transfer film, the second layer is a car sticker, and the third layer is a backing paper. The size is 4.72 in x 3.54 in.
- How to use: Turn the sticker over before sticking it, and gently scrape it with a scraper or credit card to tear off the backing paper instead of tearing off the transfer film. When tearing off, try to move as slowly as possible to avoid sticking of the sticker.
- Pasting method: After determining the position of the car sticker, after cleaning the place where it needs to be pasted, tear off the bottom paper of the car sticker, and scrape off the bubbles while sticking to ensure that there are no bubbles in the car sticker. Be careful not to apply too much force.
- Tip: Don't wax a week before the dress up sticker. The wax will make the sticker unstable. Don't stick it when the car is hot. After pasting, try to avoid water within a week and don't expose to the sun within 24 hours.
Last update on 2024-05-30 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.
SEOCONTENT-START
ALCOHOL WIPE 1. Exterior Graphics – Side Rear Window – RH and LH 2. Squeegee (1) 3. Alcohol Wipes (2). Denotes instructional steps necessary to complete the process. Denotes quality processes to be checked prior to moving to the next step. Denotes safety equipment required to be used such as a mask, goggles, rubber gloves, and hearing protection. Denotes cautions to be taken to avoid physical injury or electronic component damage. Denotes warnings that may lead to serious physical injury or vehicle damage. Denotes specific tools that are necessary to complete the step. Denotes cautions to be taken to avoid vehicle and component damage. Mask Goggles Rubber Gloves Hearing Protection SUBARU OF AMERICA PAGE 1 / 4 ISSUE DATE 00 INSTALLATION INSTRUCTIONS PART NUMBER: J121SAN500 DESCRIPTION: Exterior Graphics – Side Rear Window KIT CONTENTS: TOOLS REQUIRED: MEANING OF CHARACTERS: DESCRIPTION Exterior Graphics – Side Rear Window Soft lint-free Microfiber Cloth 1. Exterior Graphics – Side Rear Window (2). 2. Squeegee (1). 3. Alcohol Wipes (2). ALCOHOL WIPE • Water • 2ml Baby Shampoo 32 ounce Spray Bottle 9/30/21 WATER SOAP & PREPARATION – BEFORE INSTALLATION: SUBARU OF AMERICA PAGE 2 / 4 ISSUE DATE 00 Remove liner from Exterior Graphic as shown. To prevent contamination, limit touching adhesive side of the Exterior Graphic by using handling tabs. 2 3 4 Notes to the Installer 1. Read the entire installation instructions prior to beginning the installation of the accessory. 2. Ensure that the vehicle is properly protected in the area that the accessory is to be installed. 3. To prevent vehicle damage, never place tools on top of painted surfaces, seats, dash pad, console or floor carpet / mat. 4. Always wear appropriate safety gear to include gloves and eye protection when required. 1. This product should be installed with proper installation tools. 2. Install this product while observing all warnings and precautions stated in this instruction booklet. 3. VERY IMPORTANT: Thoroughly wash vehicle with Soap and Water. 4. Parts storage should be flat at room temperature and in a clean dry place. Care should be taken to avoid a dusty environment. Dry Fit Thoroughly wash vehicle with a soft lint-free cloth. Wipe the panel where the Exterior Graphic will be installed with alcohol wipes. Allow the area to dry completely. 1 Alcohol Separate Liner Spray Vehicle / Adhesive of Exterior Graphic Align the Exterior Graphic into position using the handling tabs, door notches and panel edges as references. Exterior Graphics – Side Rear Window Spray the adhesive side of the Exterior Graphic with the soap and water solution. Then spray the vehicle surface where the Exterior Graphic will be installed. Exterior Graphic Liner Premask 9/30/21 DESCRIPTION Exterior Graphics – Side Rear Window WATER SOAP & Premask / Handling Tab Exterior Graphic Liner *(Repeat Steps 1-9 for the opposite side of vehicle.) SUBARU OF AMERICA PAGE 3 / 4 ISSUE DATE 00 Use caution not to scratch the paint surface with the squeegee. 6 7 Spray Exterior Graphic Premask While using the handling tabs align the Exterior Graphic into position.This allows the part to float on the surface until proper fit is achieved. Using smooth even overlapping strokes squeegee the Exterior Graphic into position. 5 Exterior Graphic Placement Squeegee Exterior Graphic Spray the top surface of the premask with the soap and water solution. This makes it possible for the squeegee to slide easily across the surface. 8 9 Remove Premask Carefully remove the premask from the Exterior Graphic by slowly lifting and pulling backward at an 180º angle as shown. Inspect Exterior Graphic If bubbles are present after premask carrier removal, wrap a towel around the squeegee and carefully attempt to push the bubble to the side of the Exterior Graphic. If the bubble cannot be moved, use a sewing needle to pierce the bubble and press the remaining solution from beneath the Exterior Graphic. 9/30/21 DESCRIPTION Exterior Graphics – Side Rear Window WATER SOAP & Exterior Graphic Premask Results of the Check Care and Cleaning Items to be Checked Results of the Check Visual Check Items to be Checked After an Exterior Graphic installation has been completed, do not high pressure wash the vehicle for 72 hours. Make sure all edges are firmly adhered. ISSUE DATE SUBARU OF AMERICA PAGE 00 9/30/21 4 / 4 DESCRIPTION Exterior Graphics – Side Rear Window ALCOHOL WIPE SUBARU OF AMERICA PAGE 1 / 4 ISSUE DATE 00 ALCOHOL WIPE 9/30/21 1. Graphique extérieur – Vitre latérale arrière (2). 2. Racloir (1) 3. Lingettes Alcoolisées (2). CONTENU DE LA TROUSSE : DESCRIPTION: Graphiques extérieurs – Vitre latérale arrière NUMÉRO DE PIÈCE : J121SAN500 INSTRUCTIONS D’INSTALLATION • L’eau • 2ml de Shampooing OUTILS REQUIS: Linge en microfibre doux et non pelucheux Flacon pulvérisateur de 946 ml (32 oz) shampoo & d’eau SIGNIFICATION DES SYMBOLES: Indique la marche à suivre pour compléter le processus. Indique les vérifications de qualité à effectuer avant de passer à la prochaine étape. Indique l’équipement de sécurité requis et devant être utilisé, comme un masque, des lunettes de sécurité, des gants en caoutchouc et des dispositifs de protection antibruit. Indique les précautions à prendre pour éviter les blessures ou les dommages aux composants électroniques. Indique les avertissements de possibilité de blessure grave ou de dommages au véhicule. Indique les outils nécessaires pour compléter une étape. Indique les précautions à prendre pour éviter les dommages au véhicule et aux composants. Masque Lunettes de sécurité Gants en caoutchouc Dispositif de protection antibruit DESCRIPTION Graphique Extérieur – Vitre latérale arrière 1. Graphique extérieur – Vitre latérale arrière – RH et LH 2. Racloir (1) 3. Lingettes Alcoolisées (2). SUBARU OF AMERICA PAGE 2 / 4 ISSUE DATE 00 2 3 4 1 9/30/21 1. Ce produit doit être installé avec les outils d’installation adéquats. 2. Installez ce produit tout en respectant toutes les mises en garde et précautions signalées dans ce livret d’instructions. 3. TRÈS IMPORTANT : Bien laver le véhicule avec du savon et de l’eau. 4.Les pièces doivent être entreposées à plat et à température ambiante dans un endroit propre et sec. Il faut veiller à éviter tout environnement poussiéreux. PRÉPARATION – AVANT L’INSTALLATION: 1. Lisez l’ensemble des instructions d’installation avant de commencer l’installation de l’accessoire. 2. Assurez-vous que la zone du véhicule est bien protégée là où l’accessoire doit être installé. 3. Pour éviter tout dommage au véhicule, ne jamais poser d’outils sur les surfaces peintes, les sièges, le dessus du tableau de bord, la console ou les tapis de sol. 4. Portez toujours les équipements de protection appropriés, y compris des gants et des lunettes de protection pour les yeux au besoin. Remarques à l’intention de l’installateur Graphique Extérieur – Vitre latérale arrière Prémasque / Languette de manipulation Prémasque / Languette de manipulation Graphique extérieur Graphique extérieur Pellicule protectrice Pellicule protectrice Alcool Laver le véhicule soigneusement avec un linge doux et non pelucheux. Essuyer le panneau à l’endroit où le graphique extérieur sera posé à l’aide de lingettes imbibées d’alcool. Laisser la surface sécher complètement. Ajustement à sec Aligner le graphique extérieur en position en utilisant les languettes de manipulation, les encoches de porte et les bords du panneau comme points de repère. Retirer la pellicule protectrice Retirer la pellicule protectrice du graphique extérieur, comme illustré. Pour éviter toute contamination, limiter les contacts avec le côté adhésif du graphique extérieur en utilisant les languettes de manipulation. Vaporiser le véhicule/l’élément adhésif du graphique extérieur Vaporiser l’élément adhésif du graphique extérieur avec la solution d’eau savonneuse. Vaporiser ensuite la surface du véhicule à l’endroit où le graphique extérieur sera posé. DESCRIPTION Graphique Extérieur – Vitre latérale arrière SUBARU OF AMERICA PAGE 3 / 4 ISSUE DATE 00 6 7 5 8 9 9/30/21 Retirer le prémasque Inspecter le graphique extérieur Si des bulles sont présentes après le retrait du prémasque, envelopper le racloir d’une serviette et tenter attentivement de pousser la bulle vers le côté de l’autocollant. S’il est impossible de déplacer la bulle, utiliser une aiguille à coudre pour percer la bulle et extraire la solution restante qui se trouve sous le graphique extérieur. Faire attention pour ne pas rayer la surface peinte avec le racloir. Racler le graphique extérieur Racler le graphique extérieur à l’aide de mouvements légers et de chevauchement uniforme jusqu’à ce qu’il soit en place. Retirer délicatement le prémasque du graphique extérieur en le soulevant lentement puis en le tirant vers l’arrière à un angle de 180°, comme illustré. Vaporiser le prémasque du graphique extérieur Vaporiser la surface supérieure du prémasque avec la solution d’eau savonneuse. Cela permet au racloir de glisser facilement sur la surface. Position du graphique extérieur Aligner le graphique extérieur à l’endroit désiré en vous servant des languettes de manipulation. Cela permet à la pièce de glisser sur la surface jusqu’à ce qu’elle soit correctement positionnée. *(Répéter les étapes 1 à 9 sur le côté opposé du véhicule.) DESCRIPTION Graphique Extérieur – Vitre latérale arrière Prémasque / Languette de manipulation Graphique extérieur ISSUE DATE SUBARU OF AMERICA PAGE 00 9/30/21 4 / 4 Résultats de la vérification Nettoyage Et Entretien Éléments à vérifier Éléments à vérifier Résultats de la vérification Vérification Visuelle Vérifier que tous les bords sont bien collés. Une fois l’installation d’un graphique extérieur terminée, ne pas laver le véhicule à haute pression pendant 72 heures. DESCRIPTION Graphique Extérieur – Vitre latérale arrière
**************************************************************************************************************
SEOCONTENT-END