| “This site contains affiliate links for which OEMDTC may be compensated” |
Accessory Installation Guide
| 2024MY Crosstrek (non-Wilderness trims)- Mud Flaps | J101SFN400 |
INSTALLATION INSTRUCTIONS
DESCRIPTION
Crosstrek Mud Flaps
Front Installation
Installation a l’avant
1. Turn wheel to gain access to drill location
2. Drill 2mm (3/32″) hole as a guide hole up to 14mm (9/16″) depth max
3. Re-drill to 7mm (9/32″) up to 14mm (9/16″) depth max
1. Tournez la roue pour accéder à l’emplacement de la perceuse
2. Percez un trou de 2mm (3/32”) comme trou de guidage jusqu’à 14 mm (9/16”) de profondeur max
3. Re-percez à 7mm (9/32”) jusqu’à 14 mm (9/16)” de profondeur max
Rear Installation 6
Installation a l’arriere
1. Drill 2mm (3/32”) hole as a guide hole up to 14mm (9/16”) depth max
2. Re-drill to 8mm (5/16”) up to 14mm (9/16”) depth max
1. Percez un trou de 2mm (3/32”) comme trou de guidage jusqu’à 14 mm (9/16”) de profondeur max
2. Re-percez à 8mm (5/16”) jusqu’à 14 mm (9/16)” de profondeur max
Repeat steps for the other side of the vehicle
Reprendre les memes etapes l’autre cote de vehicle
J101SFN400
https://static.oemdtc.com/AccessoryInstallationGuide/J101SFN400.pdf
Loading...
Reload document 
Open in new tab
| “This site contains affiliate links for which OEMDTC may be compensated” |
SEOCONTENT-START
ISSUE DATE SUBARU OF AMERICA PAGE EDITION A JUN 01, 2022 1/3 J101SFN400 INSTALLATION INSTRUCTIONS INSTRUCTIONS D’INSTALLATION DESCRIPTION Crosstrek Mud Flaps DESCRIPTION PART NUMBER NUMERO DE PIECE Garde-Boue: Crosstrek KIT CONTENTS: CONTENU DE L’ENSEMBLE REMOVE Enlever INSTALL Installer RE-USE Réutiliser TOOLS REQUIRED: OUTILS REQUIS MEANING OF CHARACTERS: SIGNIFICATION DES SYMBOLES DISCARD Jeter / recycler NOTE: Mud flaps will decrease vehicle ground clearance. Use caution when driving over obstacles such as curbs and when entering automatic car washes. REMARQUE: Les garde-boue réduisent la garde au sol du véhicule. Soyez prudent lorsque vous franchissez des obstacles tels que des bordures de trottoir et lorsque vous entrez dans les OVER-TIGHTENING THE SCREWS IS NOT ADVISED AS THIS MAY CAUSE THE MUD-FLAP TO LOCALLY DEFORM. lave-autos automatiques. IL EST DÉCONSEILLÉ DE TROP SERRER LES VIS CAR CELA POURRAIT DÉFORMER LOCALEMENT LE GARDE-BOUE. J101SFN400 INSTALLATION INSTRUCTIONS INSTRUCTIONS D’INSTALLATION DESCRIPTION Crosstrek Mud Flaps DESCRIPTION PART NUMBER NUMERO DE PIECE Garde-Boue: Crosstrek ISSUE DATE SUBARU OF AMERICA PAGE EDITION A JUN 01, 2022 2/3 1 3 4 Front Installation 2 Installation a l’avant Wipe clean Essuyer 1. Turn wheel to gain access to drill location 2. Drill 2mm (3/32″) hole as a guide hole up to 14mm (9/16″) depth max 3. Re-drill to 7mm (9/32″) up to 14mm (9/16″) depth max 1. Tournez la roue pour accéder à l’emplacement de la perceuse 2. Percez un trou de 2mm (3/32”) comme trou de guidage jusqu’à 14 mm (9/16”) de profondeur max 3. Re-percez à 7mm (9/32”) jusqu’à 14 mm (9/16)” de profondeur max J101SFN400 INSTALLATION INSTRUCTIONS INSTRUCTIONS D’INSTALLATION DESCRIPTION Crosstrek Mud Flaps DESCRIPTION PART NUMBER NUMERO DE PIECE Garde-Boue: Crosstrek ISSUE DATE SUBARU OF AMERICA PAGE EDITION A JUN 01, 2022 3/3 7 9 8 10 5 Rear Installation 6 Installation a l’arriere Wipe clean Essuyer 1. Drill 2mm (3/32”) hole as a guide hole up to 14mm (9/16”) depth max 2. Re-drill to 8mm (5/16”) up to 14mm (9/16”) depth max Screw torque: 0.5 – 0.75 Nm (4.5~6.5 in-lb) 1. Percez un trou de 2mm (3/32”) comme trou de guidage jusqu’à 14 mm (9/16”) de profondeur max 2. Re-percez à 8mm (5/16”) jusqu’à 14 mm (9/16)” de profondeur max Couple de serrage des vis: 0,5 à 0,75 N.m (4,5 à 6,5 po-lb) Repeat steps for the other side of the vehicle Reprendre les memes etapes l’autre cote de vehicle Screw torque: 0.5 – 0.75 Nm (4.5~6.5 in-lb) Couple de serrage des vis: 0,5 à 0,75 N.m (4,5 à 6,5 po-lb)
**************************************************************************************************************
**************************************************************************************************************
SEOCONTENT-END