| “This site contains affiliate links for which OEMDTC may be compensated” |
NHTSA ID Number: 10234292
Manufacturer Communication Number: 077112
Summary
Revised Packing Material for the License Plate Lamp.
NUMBER: 07-71-12
DATE: 12/03/12
| APPLICABILITY: | 2008-2010MY 5-Door Impreza |
| SUBJECT: | Revised Packing Material for the License Plate Lamp |
INTRODUCTION
The packing (gasket) material for the license plate lamp has been revised to improve the sealing performance to the rear gate panel. The new material is thicker to provide a better seal and help prevent corrosion which may develop as a result of contact between edges of the lamp assembly and the paint finish.
PART INFORMATION
| PART NAME | PART NUMBER |
| Packing Lic Lamp | 84391FG000 |
SERVICE PROCEDURE / INFORMATION
Cross-Sectional View of License Lamp and Rear Gate
- Remove the license lamp assembly from the rear gate following the procedure in the applicable Service Manual.
- Using a plastic trim tool, remove all of the old packing material from the license lamp assembly. Clean off all residual adhesive and dirt using a plastic safe adhesive remover like “Goo Gone” or similar product.
The photos above show the new packing material. The side with lettering is the adhesive side (left).
- Once the license lamp is completely clean and dry, peel the paper from the adhesive side and carefully attach it to the back of the lamp making sure none of the new packing extends over the edges. Work out any trapped air bubbles to the closest edge.
- Confirm any paint repairs to the lamp opening in the rear gate are completely dry before reinstalling the license lamp.
- Peel the paper off the other side of the packing.
- Reinstall the bulb socket and then the lamp assembly into the rear gate to complete the repair.
5 Affected Products
Vehicles
1 Associated Document
Manufacturer Communications
NUMBER: 07-71-12
DATE: 12/03/12
MC-10234292-9999.pdf 523.282KB
Loading...
Reload document 
Open in new tab
- COMPATIBILITY: Compatible with Chevy Silverado 1500 2500 3500, Suburban Tahoe, Chevy Avalanche, GMC Sierra 1500 2500 3500, Yukon /Yukon XL, for Escalade, etc. (For more details, please refer the description.)
- EXTREMELY BRIGHT: Each lamp has 18 SMD 6,000K white 3014 led chips. 300% brighter than your factory license plate lights, maximize the rear end illumination but no blind to back up camera
- 15 MINUTES INSTALLATION: Non-polarity plugs, simply plug & play, direct fit into original housing without modifications. Simple upgradation but greatly increase the visibility of your license plate.
- CAN-BUS READY: Better electric circuit stability, error free for 99% of vehicles, no OBC (on-board computer) error warnings, no interference with FM radio.100% street legal
- LONGER LIFESPAN: Made of quality and flame resistant PC material. IP65 waterproof rate ensures LESAUCE tag lights working over 50,000hrs under different circumstance
- Voltage: 12V, color: 6000K xenon white, power: 2w/pc, lumen:500lm, dimensions: 1 by 0.47 inches, net weight: 2g/pc. Low power consumption for longer lifespan
- Each bulb has 24 pieces of 3014 led chips on it, 360 degree lighting angle, no blind spot, super bright brings your car a refreshed new look
- Fit bulb sizes: 168, 175, 194, 2825, W5W, T10, etc. Easy to install, just plug and play. Canbus error free, no error after installation
- Wide application: These led bulbs can be used for license plate tag light, map lights, dome light, front/rear side marker lights, trunk cargo room lights, turn signal lights, reading lights, glove box lights, inner tail light bulb, etc
- Package includes 2 pieces of AUXITO 194 led bulbs. Note: Amazon filter system may not be 100% accurate, the bulb size may vary between trim of your vehicle. Please double check owners manual or original bulb size to confirm
- 12SMD high brightness LED chips per lights for maximum illumination.
- Working Voltage: 12V, universal fit for any 12V cars, trucks, trailers, & RV's.
- Just fit the hole distance of the license plate, very simply 2 wires hook-up installation.
- More than 300% brighter than original halogen bulb, built in stable current IC driver for longer lifespan.
- Warranty: fully ONE YEAR guaranteed for the manufacturer defect. Please check the fitment note application before purchasing.
- 【Wide Application】Great for license plate light, courtesy light, dome/roof light, trunk/cargo light for trucks, SUV, trailers, vans, off-road vehicles as additional add-on lamp.
- 【Bright Light&Waterproof】This truck license plate led light powered by 6 pieces upgrade LED chips. Super bright LED(6 LED lights) provide maximum visibility and safety.
- 【Easy to install】Direct bolt-on, Easy to install, red wire for positive and black for negative. shock resistant.
- 【Long Lifespan】long life span and low power consumption. High temperature resistant PC lens, Anti-vibration ABS shell, high strength and good toughness.
- Application: license plate light, tail light, side light, license plate tag light, courtesy door step light, dome/roof light, trunk/cargo light, under hood light etc.
- Compatible with 1999 to 2016 Ford F-Series Superduty F250 / F350 / F450 / F550, 1990 to 2014 Ford F150, 1990 to 1999 Ford F250, 1990 to 1997 Ford F350, 2004 Ford F150 Heritage, 1990 to 1996 Ford Bronco, 1984 to 1988 Ford Bronco II, 1983 to 2011 Ford Ranger, 1991 to 2004 Ford Explorer, 1991 to 2010 Ford Explorer Sport Trac, 2000to 2005 Ford Excursion, 1997 to 2002 Ford Expedition, 2006 to 2008 Lincoln Mark LT
- Brighter Than Stock Bulbs: Built-in high power 3 SMD LED chips, super bright 6000k white light output illuminates license effectively. With CANBUS control unit, no error code, a best replacement for OEM
- Fully sealed: Our license plate lights passed waterproof test, made of high quality material, no corrosion, anti-scratch, no faded with long-time exposure and can adapt to all kind of extreme weather, no water inside after a heavy rain or car wash anymore
- Easy Installation: Plug and play, exact fit and direct replacement, no modification or trimming needed, just take out your original bulbs and insert new plug into socket. Non-Polarity, no need to worry positive and negative connections
- Package Including: 2 x license plate lamps with instruction.
- 【Bright Light and Waterproof】: This truck license plate led bulb powered by 6 pieces upgrade LED chips. Principle of arc surface optical illumination outputs more and brighter beams. Sealed by high quality waterproof gel, this strong waterproof function allows you to driving worry-free in rainy or snow days.
- 【Parameter】:Voltage: 12V-30V; Wattage: 1.2W; Bulb Size: 66*33*22mm L*W*H (2.6*1.3*0.9in).; Wire length:152mm(6in); Weight: 14g(0.03lb)/bulb; Brightness: 100 lumens for each bulb. Screw hole distance 55 mm(2.2in). Two wires design. Easy to install, red wire for positive and black for negative.
- 【Long Lifespan】: Gold wire copper bracket lamp beads and smart IC driver insure bright light, low consumption, constant current and long lifespan. High temperature resistant PC lens, Anti-vibration ABS shell, high strength and good toughness.100% quality guarantee and buy with no worry.
- 【Warm Prompt】:Amazon's Recommender System is not 100% accurate.Please measure the location before purchasing.The distance from screw hole to screw hole is 2.2in (55mm).There are four screws inside the packaging.And the LED license plate light can directly screwed into the installation position.Convenient and firm.
- 【Application】: Our truck license plate led lights can be used as license plate light, courtesy light, dome/roof light, trunk/cargo light for truck, SUV, trailers, motorcycle, off-road truck, vans, bus, boat and other different kind of vehicles.
- Lights Dim Over Time, Replace In Pairs: Your lights are a pair, one is never turned on without the other. If one bulb burns out, the other isn't far behind
- Easy To Replace: Sylvania Long Life miniature bulbs are easy to install and show instant results
- Low Maintenance And High Durability: Designed for durability, greater safety, and lower maintenance by the leading supplier of automotive lighting
- Longer Life Than Most Standard Bulbs: Long Life bulbs perform twice as long as any other standard miniature bulbs
- The Sylvania Standard Of Quality: With over 100 years in business, Sylvania is the world leader in automotive lighting for Original Equipment Manufacturers (OEMs) and the aftermarket
- Universal fit for all full size US license plates
- Powder coated zinc housing
- UV stable, diffused waterproof epoxy layer encapsulating LEDs
- 86" wire with waterproof connector
- Constant current LED drivers maintain brightness level from 10-16V
- Fit bulb size: T10, 147, 152, 158, 159, 161, 168, 175, 184, 192, 193, 194, 2825, W5W, 194 LED bulb can fit map light, dome light, license plate light, trunk light, courtesy light, side marker light, interior door light, parking light
- Notice: 194 led bulbs could fit most of positions of car, do not fit all positions of your car, according to the year and model of your car, please double check owner's manual, for 12V vehicle
- Better beam pattern: each bulb has 5 pcs high power SMD led, color temperature: 6000K(xenon white), voltage: 12V
- No polarity no flip: it is truly no polarity, can light on two sides, no need more modification or flip, plug and play, easy install within 5 minutes
- Tips: 10 packs of 194 led bulbs of one set, for some vehicles, It may need a canbus decoder to fix flickering or error code
- HIGH BRIGHTNESS: 194 LED bulbs uses 12pcs 4014SMD and 1pcs 3030SMD Chips. 300% brighter than stock bulbs, 6500K white provides better visibility. 360° lighting angle for allover light emission, no dark spots or shadowed areas.
- LONG LIFESPAN: AUTOONE T10 led bulb adopts full aviation aluminum body, built in intelligent IC to optimize LED working temperature. Energy efficient and better heat dissipation, extend the lifespan up to 45,000 hrs.
- EASY TO INSTALL: Non-polarity, plug and play. No error, no flickering after installation for 98% of vehicles. Almost 1:1 same size as halogen bulbs, providing you with a hassle-free installation experience. Note: Although built-in CANBUS, some vehicles especially German cars might still pop up error message(the 194 bulb still function)
- FITMENT: Direct LED replacement for all T10 Wedge Type - for 147, 152, 158, 159, 161, 168, 175, 184, 192, 193, 194, 195, 2825, 906, 912, W5W bulbs. NOTE: This product is not suitable for license plate lights of Ford F150 series vehicles.
- WIDELY APPLICABLE: T10 194 168 led bulbs can be used for license plate light, led interior car lights, map lights, dome light, front/rear side marker lights, trunk cargo room lights, turn signal lights, reading lights, glove box lights, inner tail light bulb, etc. NOTE: Please check the user manual and the bulb size to verify the compatibility before purchasing.
SEOCONTENT-START
Bulletin Number: 07-71-12; Date: 12/03/12 Page 1 INTRODUCTION The packing (gasket) material for the license plate lamp has been revised to improve the sealing performance to the rear gate panel. The new material is thicker to provide a better seal and help prevent corrosion which may develop as a result of contact between edges of the lamp assembly and the paint finish. PART INFORMATION PART NAME PART NUMBER Packing Lic Lamp 84391FG000 SERVICE PROCEDURE / INFORMATION NUMBER: 07-71-12 DATE: 12/03/12 APPLICABILITY: 2008-2010MY 5-Door Impreza SUBJECT: Revised Packing Material for the License Plate Lamp SERVICE BULLETIN ATTENTION: GENERAL MANAGER q PARTS MANAGER q CLAIMS PERSONNEL q SERVICE MANAGER q IMPORTANT – All Service Personnel Should Read and Initial in the boxes provided, right. Continued… CAUTION: VEHICLE SERVICING PERFORMED BY UNTRAINED PERSONS COULD RESULT IN SERIOUS INJURY TO THOSE PERSONS OR TO OTHERS. Subaru
Service Bulletins are intended for use by professional technicians ONLY. They are written to inform those technicians of conditions that may occur in some vehicles, or to provide information that could assist in the proper servicing of the vehicle. Properly trained technicians have the equipment, tools, safety instructions, and know-how to do the job correctly and safely. If a condition is described, DO NOT assume that this Service Bulletin applies to your vehicle, or that your vehicle will have that condition. SUBARU OF AMERICA, INC. IS “ISO 14001 COMPLIANT” The international standard for excellence in Environmental Management Systems. Please recycle or dispose of automotive products in a manner that is friendly to our environment and in accordance with all local, state and federal laws and regulations. Rear gate panel Rear gate garnish Inspect for any corrosion around the lamp opening in the rear gate panel. Repair as needed before reinstalling the lamp. License lamp Cross-Sectional View of License Lamp and Rear Gate Bulletin Number: 07-71-12; Date: 12/03/12 Page 2 Continued… • Remove the license lamp assembly from the rear gate following the procedure in the applicable Service Manual. • Using a plastic trim tool, remove all of the old packing material from the license lamp assembly. Clean off all residual adhesive and dirt using a plastic safe adhesive remover like “Goo Gone” or similar product. The photos above show the new packing material. The side with lettering is the adhesive side (left). • Once the license lamp is completely clean and dry, peel the paper from the adhesive side and carefully attach it to the back of the lamp making sure none of the new packing extends over the edges. Work out any trapped air bubbles to the closest edge. • Confirm any paint repairs to the lamp opening in the rear gate are completely dry before reinstalling the license lamp. Remove the original packing and adhesive. (Bulb socket installed) Bulletin Number: 07-71-12; Date: 12/03/12 Page 3 • Peel the paper off the other side of the packing. • Reinstall the bulb socket and then the lamp assembly into the rear gate to complete the repair. WARRANTY / CLAIM INFORMATION Any related paint damage should be claimed as a spot repair. For vehicles within the Basic New Car Limited Warranty period, this repair may be claimed using the following information: LABOR DESCRIPTION LABOR OPERATION # FAIL CODE LABOR TIME Packing, License Plate Lamp, One or Both R&R A916-216 XMD-48 0.2 New packing installed (Bulb socket removed)
SEOCONTENT-END
Last update on 2025-04-17 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.
