| “This site contains affiliate links for which OEMDTC may be compensated” |
Accessory Installation Guide
| 2022-24MY BRZ – Door Projector Light | H4610CC000 |
Installation Manual
DOOR PROJECTOR LIGHT
SUBARU
BRZ 2024MY ～
PART NO．H4610CC000
For installers
Important
- We recommend that this product should be installed by a Subaru dealer. Damage and injury resulting from improper assembly will not be warranted.
- When installing or removing vehicle parts, pay careful attention not to damage the parts.
- Ensure that the harnesses are wired safely and properly so that a short circuit does not occur, for example, due to a contact with a sharp edge of a body panel.
- For details on how to remove and install vehicle parts, refer to the service manual.
Warning・・・Be sure to observe the following for safety. Failure to observe these instructions could lead to danger to life or serious damage.
- Perform this work in a sufficiently spacious and fl at space while paying attention to safety. Also, perform this work with the shift knob in neutral or parking, the parking brake set, the engine stopped, and the key removed.
- Avoid performing this work in an area exposed to rain, etc. Working with wet hands is very dangerous, as doing so could lead to an electric shock. Also, provide adequate ventilation and pay adequate attention to prevent accumulation of exhaust gas etc.
Caution・・・When using or installing this product, be sure to observe the following. Failure to observe these instructions could lead to product performance deterioration or property damage.
- Before starting the work, be sure to disconnect the negative (-) battery terminals.
- When disconnecting and connecting the connector, hold the connector and ensure to do so securely.
If the connector is not connected securely, the light may not come on. - When connecting the connector, secure the connector fi rmly by inserting it all the way.
- Do not pull the harness with excessive force. Doing so may cause the terminal to come off , resulting in a contact failure. Also, wire the harness so that it is not caught in the moving part.
- When removing or restoring the vehicle parts to their original states, follow the service manual.
- When removing dirt on the product, wipe it off with sponge or other cloth dampened with neutral detergent.
Never use an organic solvent, such as thinner, or acid or alkaline cleaner.
1
（1）Turn off the ignition switch.
（2）Disconnect the negative (-) battery terminal.
2
（1）Apply a waste cloth on a fl at head screwdriver. Remove the courtesy lamp by inserting the fl at head screwdriver into the vehicle’s front side of the courtesy lamp.
（2）Remove the connector from the courtesy lamp.
CAUTION
When removing the vehicle parts, follow the service manual and be careful not to scratch or damage them.
3
Confirm L/R side is correct. Connect the DOOR PROJECTOR LIGHT to the courtesy lamp connector.
4
Insert the DOOR PROJECTOR LIGHT into the door trim. Ensure the front side tab is locked at the correct position.
Repeat Steps 2 － 4 for the R Side Door.
5
Connect the negative (-) battery terminal.
6
Open the door and confirm the DOOR PROJECTOR LIGHT’s image is correctly projected.
7
Confirm the DOOR PROJECTOR LIGHT unit is securely fixed to the door trim.
Open/close the door and check the DOOR PROJECTOR LIGHT unit does not contact with the door-sill, does not move, or fall off .
H4610CC000
Loading...
Reload document 
Open in new tab
- Customized for SUBARU Forester/Outback /Legacy/XV/Impreza /Tribeca/Ascent . Integrally injection-molded, will not separate and deform during installation.
- HIGH DEFINITION AND BRIGHT PROJECTION - This door light sign projector is powered by a 12V power cord and uses a high brightness LED chip. When you open the door, the light passes through 6 layers of ultra-high definition precision lenses to project a bright and vivid courtesy welcome sign on the floor.
- Built-in Smart Chip- The LED Ghost Projector uses the latest automotive decoding circuit chip that will not conflict with your car's software. Uses high quality circuit boards and parts that can carry more current. Adopt high brightness LED chip with waterproof, shockproof and anti-corrosion ABS flame retardant housing, strong and durable, high temperature and pressure resistant, better protect the lens and internal chip circuit.
- Easy to install - plug and play! No drilling, no wiring, no disassembly, no damage to your car. Specially designed for Subaru car tuning and enthusiasts. The old lights just need to be pried forward gently, and the new lights can be stuck in place by hand.
- Note: The original position of the car does not have a light position or not energized, you need to add a line modification.
- 【Compatible】For:Forester 2013-2024,Outback 2012-2024, Legacy 2010-2021, XV 2011-2017, Impreza 2010-2021, Tribeca 2011 Note: When you want to use these marker lights as replacement lights, first make sure that your car has the original door lights.
- 【Easy to Install】 : Using flathead screwer to pop out your current lights, unplug them, plug our logo light in, and pop them back into the cutout.No drilling, no disassembling, no damage to your car.
- 【LED Lighting】: Utilizes advanced LED technology for a bright, clear projection that is visible in both low light and complete darkness.Durable and Long-Lasting: Constructed with premium materials to withstand daily use, ensuring long-lasting performance and durability.
- 【Energy Efficient】: Low power consumption ensures your car battery remains unaffected while providing superior illumination.Elevate Your Car's Style
- 【Package】1 box containing 2 light fixtures.
- 【Compatible for】Forester Fourth generation 2013-2017 SJ,Forester Fifth generation 2018-PRESENT SK
- 【Super cool 】When the door is opened, the Forester LOGO is illuminated onto the open door surface to provide a light to aid entry into and out of the vehicle.
- 【Easy to install】 Direct Replacement. No modifications required. No wire cutting. Please kindly confirm your original car door light can be powered before purchasing.
- 【Product Features】 High-brightness led door projection lamp, to show your car a bright, clear and color-fast logo projection
- 【After sale】 If there are any problems with our products, just feel free to contact us.
- Compatible Car Models: LED Car Door Lights Projector Compatible for Subaru Wilderness Outback Forester. NOTE: Make sure your car has a door light and that it lights up when you open the door
- HD & Non-fading: LED car door projector lights for Subaru Wilderness Outback Forester with the latest nano-glass clips technology to ensure high definition projection patterns, brilliant colors and will not fade. Provides illumination for safety while displaying a uniquely patterned logo
- PREMIUM QUALITY: Car puddle lights for outback forester is made of sturdy ABS flame retardant housing and upgraded heat dissipating aluminum backshell, with excellent waterproof, shockproof and high temperature resistance, allow you to use the car door lights with peace of mind
- Exclusive Customization for Subaru Wilderness Outback Forester: Make your car more cool! For subaru outback door lights specially made for Subaru Wilderness Outback Forester, the unique logo design highlights the taste and personality of OUTBACK owners. Provide the wonderful experience for your family, friends and partners every time they on and off the car
- Easy Installation: for subaru forester door lights easy to install in 4 simple steps. Use a flat head screwdriver to pry off the original lights, Unplug the socket of the original light, insert our puddle lights and Put it back into the cutout, anatomical design ensures no damage to your car
- 【Compatible with Multiple Subaru Models】 Designed specifically for Subaru Forester (2013-2024), Outback (2012-2024), Legacy (2010-2021), Impreza (2010-2021), and XV (2011-2017). Ensure your car has original door lights that can power the LEDs.
- 【High-Definition 3D Projection】 Equipped with a high-brightness LED chip, this projector delivers a vivid and bright Subaru logo projection on the ground. The light passes through six layers of precision lenses for maximum clarity and impact.
- 【Built-in Smart Chip】 The integrated smart chip ensures smooth operation without interfering with the vehicle's software. The advanced circuit board can handle more current, protecting the lens and internal components from damage.
- 【Easy Plug-and-Play Installation】 No drilling or complicated modifications required. Simply replace your existing door lights with these plug-and-play units. Enjoy a clean and hassle-free installation with no need for additional wiring.
- 【Durable and Weather-Resistant】 Crafted from ABS flame-retardant materials, these lights are waterproof, shockproof, and resistant to corrosion. They withstand high temperatures and maintain brightness even under pressure.
- 【Compatible for】 CROSSTREK Fourth generation 2013-2017 SJ Fifth generation 2018-PRESENT SK
- 【High Quality】Featuring high definition projection with a premium lens, these puddle lights offer a longer lifespan, brighter output, and lower power consumption.
- 【Product Features】The colorfast quartz glass lens is used, which is durable, and the high brightness led door projection lamp displays bright and clear logo projection for your car, making your car unique
- 【Easy to install】 Direct Replacement. No modifications required. No wire cutting. Please kindly confirm your original car door light can be powered before purchasing.
- 【After sale】We offer full after-sale support. If there are any problems with our products, please feel free to contact us.
- 【Compatible for】Ascent 2019-2022
- 【Super cool 】When the door is opened, the LOGO is illuminated onto the open door surface to provide a light to aid entry into and out of the vehicle.
- 【Easy to install】 Direct Replacement. No modifications required. No wire cutting. Please kindly confirm your original car door light can be powered before purchasing.
- 【High-quality LED chip】 Very low power consumption, will not add burden to your car battery
- 【after-sales 】 If you have any questions or other questions about the product, please feel free to contact us, we will solve it for you immediately
- 【Compatibility】BRZ ZN6/ZC6 ,2012 - June 2020
- 【Never fade 】Never fade high brightness BRZ logo slides 2pcs set car door ghost shadow projector logo light ,High-brightness led door projection lamp, to show your car a bright, clear and color-fast logo projection
- 【Easy to install】 Direct Replacement. No modifications required. No wire cutting. Note: Before purchasing, you must first confirm whether the car has original door lights, if not, it is incompatible
- 【Super cool 】When the door is opened, the BRZ is illuminated onto the open door surface to provide a light to aid entry into and out of the vehicle.
- 【After sale】 If there are any problems with our products, just feel free to contact us.
- [Car Compatibility] Compatible with Forester 2013-2024,Outback 2012-2024,Ascent 2019-2022, Legacy 2010-2021, XV 2011-2017, Impreza 2010-2021, Tribeca 2011.
- [Performance] Better brightness and clarity. Our car door projector lights are the upgraded products, brighter and more clear than others.
- [Easy Installation] Put in the car door light logo directly with our install tool. No need for patch cords. No damage and no drilling for installation.
- [Product Feature] We use glass lens instead of the cheaper plastic lens for car door light logo. The color of the car door lights will not fade.
- [Note] Please make sure your car has front door lights that can power on the front side door before purchasing.
SEOCONTENT-START
-1- PART NO．H4610CC000 DOOR PROJECTOR LIGHT PKI-0094-2 △ 01 Warning・・・Be sure to observe the following for safety. Failure to observe these instructions could lead to danger to life or serious damage. ・ Perform this work in a suffi ciently spacious and fl at space while paying attention to safety. Also, perform this work with the shift knob in neutral or parking, the parking brake set, the engine stopped, and the key removed. ・ Avoid performing this work in an area exposed to rain, etc. Working with wet hands is very dangerous, as doing so could lead to an electric shock. Also, provide adequate ventilation and pay adequate attention to prevent accumulation of exhaust gas etc. For installers Important ・ We recommend that this product should be installed by a Subaru dealer. Damage and injury resulting from improper assembly will not be warranted. ・ When installing or removing vehicle parts, pay careful attention not to damage the parts. ・ Ensure that the harnesses are wired safely and properly so that a short circuit does not occur, for example, due to a contact with a sharp edge of a body panel. ・ For details on how to remove and install vehicle parts, refer to the service manual. Caution・・・When using or installing this product, be sure to observe the following. Failure to observe these instructions could lead to product performance deterioration or property damage. ・ Before starting the work, be sure to disconnect the negative (-) battery terminals. ・ When disconnecting and connecting the connector, hold the connector and ensure to do so securely. If the connector is not connected securely, the light may not come on. ・ When connecting the connector, secure the connector fi rmly by inserting it all the way. ・ Do not pull the harness with excessive force. Doing so may cause the terminal to come off , resulting in a contact failure. Also, wire the harness so that it is not caught in the moving part. ・ When removing or restoring the vehicle parts to their original states, follow the service manual. ・ When removing dirt on the product, wipe it off with sponge or other cloth dampened with neutral detergent. Never use an organic solvent, such as thinner, or acid or alkaline cleaner. Installation Manual SUBARU BRZ 2024MY ～ -2- NO. ① ② Part name DOOR PROJECTOR LIGHT L DOOR PROJECTOR LIGHT R Quantity 1 １ ① ② ● Waste cloth ● fl at head screwdriver Completion drawing Components DOOR PROJECTOR LIGHT “L” mark indicated on the backside “R” mark indicated on the backside Tools ○○○○ R A14970-2000 ○○○○ L A14970-1000 -3- Confi rm L/R side is correct. Connect the DOOR PROJECTOR LIGHT to the courtesy lamp connector. ● L side：DOOR PROJECTOR LIGHT L ● R side：DOOR PROJECTOR LIGHT R 1 3 2 Courtesy lamp Flat head screwdriver Courtesy lamp connector DOOR PROJECTOR LIGHT L L side door L side door Front of the car body Installation procedure （1）Turn off the ignition switch. （2）Disconnect the negative (-) battery terminal. （1）Apply a waste cloth on a fl at head screwdriver. Remove the courtesy lamp by inserting the fl at head screwdriver into the vehicle’s front side of the courtesy lamp. （2）Remove the connector from the courtesy lamp. When removing the vehicle parts, follow the service manual and be careful not to scratch or damage them. -4- 4 5 6 7 Insert ② ① Tab Connect the negative (-) battery terminal. Open the door and confi rm the DOOR PROJECTOR LIGHT’s image is correctly projected. Confi rm the DOOR PROJECTOR LIGHT unit is securely fi xed to the door trim. Open/close the door and check the DOOR PROJECTOR LIGHT unit does not contact with the door-sill, does not move, or fall off . L side R side Door trim DOOR PROJECTOR LIGHT Front of the car body Insert the DOOR PROJECTOR LIGHT into the door trim. Ensure the front side tab is locked at the correct position. Repeat Steps 2 － 4 for the R Side Door. -5- △ 00 ・Initial release August 31, 2023 △ Description Date Revision History
**************************************************************************************************************
**************************************************************************************************************
SEOCONTENT-END
Last update on 2025-04-17 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.
