“This site contains affiliate links for which OEMDTC may be compensated” |
NHTSA ID Number: 10166903
Manufacturer Communication Number: 15-252-19R
Summary
This Service Information Bulletin provides the procedure for programming the RES fobs used with the H001SAN100 Remote Engine Starter accessory installed on (turn) Key Start -equipped vehicles. Use this procedure whenever programming (or re-programming) a fob is needed.
NUMBER: 15-252-19R
DATE: 10/01/19
REVISED: 10/11/19
INTRODUCTION:
This Service Information Bulletin provides the procedure for programming the RES fobs used with the H001SAN100 Remote Engine Starter accessory installed on (turn) Key Start -equipped vehicles. Use this procedure whenever programming (or re-programming) a fob is needed.
SERVICE PROCEDURE / INFORMATION:
REMINDER: Customer satisfaction and retention starts with performing quality repairs.
- Open the driver’s door and enter the vehicle. IMPORTANT: The driver’s door must remain open throughout this entire programming process. Ensure all the other vehicle doors, trunk, hatch / rear gate are closed.
- Verify the transmission shifter (selector lever) is in the “park” position.
- Cycle the ignition switch “ON” then “OFF”, “ON” then “OFF”, “ON” then “OFF”, then back “ON” (3 “cycles) and leave “ON” throughout the entire programming process. IMPORTANT: These three ON/OFF ignition key cycles must be completed within five (5) seconds.
- The RES system will now flash the side marker lights, tail lights, parking lights and honk the horn three (3) times to indicate the system has entered “fob learn” (programming) mode.
- Press and hold the button on the fob being programmed for three (3) seconds. The side marker lights, tail lights, parking lights will flash and the horn honk one (1) time to indicate the system has learned the fob successfully. Release the button on the fob. In addition, the fob itself may flash / beep one (1) time to indicate successful programming.
- Repeat Step Five () for each additional fob. The system capable of accepting up to eight (8) fobs.
- Turn the ignition “OFF” to exit fob learn mode and complete the procedure.
IMPORTANT NOTE: The system will exit fob learn mode if the ignition is turned OFF, the driver’s door is closed or after thirty (30) seconds of inactivity.
2 Affected Products
Vehicles
MAKE | MODEL | YEAR |
SUBARU | LEGACY | 2020 |
SUBARU | OUTBACK | 2020 |
1 Associated Document
Manufacturer Communications
NUMBER: 15-252-19R
DATE: 10/01/19
REVISED: 10/11/19
https://www.nhtsa.gov/recalls?nhtsaId=10166903
MC-10166903-0001.pdf 1041.718KB
NHTSA ID Number: 10166882
Manufacturer Communication Number: 15-252-19
Summary
This Service Information Bulletin provides the procedures for programing the RES fobs used with the H001SAN100 Remote Engine Starter accessory installed on (turn) Key Start-equipped vehicles. Use this procedure whenever programming (or re-programming) a fob is needed.
1 Associated Document
Manufacturer Communications
NUMBER: 15-252-19R
DATE: 10/01/19
REVISED: 10/11/19
https://www.nhtsa.gov/recalls?nhtsaId=10166882
MC-10166882-0001.pdf 1041.718KB
“This site contains affiliate links for which OEMDTC may be compensated” |
- COMPLETE (4 BUTTON) REMOTE - Includes Electronics, Chip and Fresh Battery
- WORKS WITH FCC ID HYQ14AHK – 4 Button Remote – Lock, Unlock, Trunk Release and Horn/Panic
- REMOTE PROGRAMMING IS REQUIRED – The remote must be programmed to (synchronized with) your vehicle
- COMPATIBLE WITH SELECT SUBARU VEHICLES INCLUDING: Subaru Ascent – 2019-2021, Subaru BRZ – 2022, Subaru Crosstrek – 2018-2022, Subaru Forester – 2019-2022, Subaru Impreza – 2017-2021, Subaru Legacy – 2018-2021, Subaru Outback CVT – 2019-2021, Subaru STI – 2019-2021, Subaru WRX – 2019-2022
- [Complete Remote with Electronics and Chip] - Includes Electronics, Chip and Fresh Battery
- [Compatible with FCC ID HYQ14AHK] – 4 Button Remote – Lock, Unlock, Trunk Release and Horn/Panic
- [Must be Programmed by Dealer or Locksmith] - The remote must be programmed to (synchronized with) your vehicle
- [Tested and Works on the Following Vehicles] - Subaru Ascent – 2019-2021, Subaru BRZ – 2022, Subaru Crosstrek – 2018-2022, Subaru Forester – 2019-2022, Subaru Impreza – 2017-2021, Subaru Legacy – 2018-2021, Subaru Outback CVT – 2019-2021, Subaru STI – 2019-2021, Subaru WRX – 2019-2022
- [Safe a Fortune VS Purchasing from your Dealer]
- There is NO interior (remote/electronics/transponder chip)unit inside.
- The keyblade needs to be cut at your local dealer or qualified locksmith.
- This is for you to replace your old or broken shell. All you need to do is to move the internal components from your old remote to our new case.The keyblade needs to be cut at your local dealer or qualified locksmith.
- Please be certain that this is the proper key for your vehicle.
- Please make sure your key is the same with the picture before you purchase.
- Reference for P/N - FCC ID:CWTWB1U811,Part number:57497-FJ020,57497-FJ021,57497-AL00A, Chip:Letter "G" on your original blade
- Compatible Model - The compatibility is just for reference,same year and model car might have different keyless entry systems and key blade slots.Fits for Impreza 2012-2017,for WRX 2015-2019,for Forester 2014-2018,for XV Crosstrek 2013-2017,for Subaru Outback 2015-2017,for Legacy 2015-2017
- Check&Verify - The compatibility is for reference only,please confirm your FCC ID,Part Number,Chip Type,Button Quantity and Key Blade of your factory key is identical with this remote key before purchasing.
- Program&Cut - Must be cut and programmed by a qualified locksmith.G chip will be installed in the key when we ship it to you - it also need to be programmed to your vehicle along with the remote control.Please note that this is an aftermarket replacement item without programming code,no need code to get it programmed.Recommended programming instrument:LONSOR K518,X100,X300,VVDI KEY TOOL PLUS PAD.
- Full Remote Key - Each of keyless entry remote comes complete with battery/chip/circuit board/uncut key blade.Please notice that this product is an aftermarket item without logo/part number/emblem/code on the key shell.
- OEM Electronic Keyless Entry Remote Head Key Fob
- MUST be Programmed and Cut by a Professional Automotive Locksmith
- “G” Transponder Chip Compatible, Unique Programming Code Included Required to Program Remote to Your Vehicle
- Match FCC ID and Part Number in Description to an Existing Remote to Ensure Compatibility with Your Vehicle
- Compatible With 2012-2018 Subaru Impreza, 2013-2016 Subaru XV CrossTrek, 2014-2018 Subaru Forester, 2015-2017 Subaru Outback, 2015-2017 Subaru Legacy
- Part Numbers/FCC ID: CWTWBU766 57497-AJ10A, 57497AJ10A Frequency: 433MHz. Note: Not a key shell, it is a whole key.
- Proximity Fob Fits for Subaru Outback 2010-2014 for Subaru Legacy 2010-2014
- Pros of Our Keyless Remote: With built in chip, sensitive response, 4 buttons car key: remote locking, unlocking, panic, trunk hold. Fast response, wireless remote control.
- Notice Programming: This remote and door key must be programmed and cut by a qualified locksmith or dealership(consult some different locksmiths before programming to ensure it is successful).NOTE a working key fob was needed in order to add a new key. This remote must be programmed and cut by a qualified locksmith or dealership
- Package for Car Key Fob:2 x Car Keyless Entry Remote (Battery is included). Size: 9.4x3.7cm / 3.70"x1.46"(L*W). Please check OE number/FCC ID and product picture with original one before purchase.
Last update on 2024-04-13 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.
SEOCONTENT-START
Bulletin Number: 15-252-19R; Date: 10/01/19 Page 1 of 2 Continued… NUMBER: 15-252-19R DATE: 10/01/19 REVISED: 10/11/19 APPLICABILITY: 2020MY Legacy and Outback SUBJECT: Remote Engine Start (RES) System Fob Programming Procedure CAUTION: VEHICLE SERVICING PERFORMED BY UNTRAINED PERSONS COULD RESULT IN SERIOUS INJURY TO THOSE PERSONS OR TO OTHERS. Subaru Service Bulletins are intended for use by professional technicians ONLY. They are written to inform those technicians of conditions that may occur in some vehicles, or to provide information that could assist in the proper servicing of the vehicle. Properly trained technicians have the equipment, tools, safety instructions, and know-how to do the job correctly and safely. If a condition is described, DO NOT assume that this Service Bulletin applies to your vehicle, or that your vehicle will have that condition. Subaru of America, Inc. is ISO 14001 Compliant ISO 14001 is the international standard for excellence in Environmental Management Systems. Please recycle or dispose of automotive products in a manner that is friendly to our environment and in accordance with all local, state and federal laws and regulations. INTRODUCTION: This Service Information Bulletin provides the procedure for programming the RES fobs used with the H001SAN100 Remote Engine Starter accessory installed on (turn) Key Start -equipped vehicles. Use this procedure whenever programming (or re-programming) a fob is needed. SERVICE PROCEDURE / INFORMATION: REMINDER: Customer satisfaction and retention starts with performing quality repairs. 1. Open the driver’s door and enter the vehicle. IMPORTANT: The driver’s door must remain open throughout this entire programming process. Ensure all the other vehicle doors, trunk, hatch / rear gate are closed. 2. Verify the transmission shifter (selector lever) is in the “park” position. 3. Cycle the ignition switch “ON” then “OFF”, “ON” then “OFF”, “ON” then “OFF”, then back “ON” (3 “cycles) and leave “ON” throughout the entire programming process. IMPORTANT: These three ON/OFF ignition key cycles must be completed within five (5) seconds. 4. The RES system will now flash the side marker lights, tail lights, parking lights and honk the horn three (3) times to indicate the system has entered “fob learn” (programming) mode. 5. Press and hold the button on the fob being programmed for three (3) seconds. The side marker lights, tail lights, parking lights will flash and the horn honk one (1) time to indicate the system has learned the fob successfully. Release the button on the fob. In addition, the fob itself may flash / beep one (1) time to indicate successful programming. 6. Repeat Step Five (5.) for each additional fob. The system capable of accepting up to eight (8) fobs. 7. Turn the ignition “OFF” to exit fob learn mode and complete the procedure. IMPORTANT NOTE: The system will exit fob learn mode if the ignition is turned OFF, the driver’s door is closed or after thirty (30) seconds of inactivity. SERVICE INFORMATION BULLETIN ATTENTION: GENERAL MANAGER q PARTS MANAGER q CLAIMS PERSONNEL q SERVICE MANAGER q IMPORTANT – All Service Personnel Should Read and Initial in the boxes provided, right. © 2019 Subaru of America, Inc. All rights reserved. Bulletin Number: 15-252-19R; Date: 10/01/19 Page 2 of 2 IMPORTANT REMINDERS: • SOA strongly discourages the printing and/or local storage of service information as previously released information and electronic publications may be updated at any time. • Always check for any open recalls or campaigns anytime a vehicle is in for servicing. • Always refer to STIS for the latest service information before performing any repairs.
**************************************************************************************************************
SEOCONTENT-END