| “This site contains affiliate links for which OEMDTC may be compensated” |
Accessory Installation Guide
2022MY WRX Strake Kit – Side | E2610VC500 |
Strake Kit – Side
Installation Manual
Genuine Part Numbe：r E2610VC500
Applicable Model： WRX 2022MY ～
Repair part model number
FITTING KIT（E2610VC518）：③×2／④×1
Tools
Waste cloth, neutral detergent or cleaning detergent [IPA (isopropyl alcohol) or nonane], masking tape, clip remover, flathead screwdriver, Phillips screw driver
This manual describes how to install the side strakes.
Request
Before installing this product, please ensure to read this manual and carry out proper installation.
Precautions
1. When installing this product, park the car on a level surface and securely apply the parking brake before carrying out the work.
2. Before the installation, use a neutral detergent (or cleaning detergent) and waste cloth to remove any dirt adhering to the car’s surface where the side strakes will be attached, and then dry the surface thoroughly. Moreover, if sand or mud adheres to the back of the clip insertion holes, etc., then clean the contaminated sections.
3. Install the side strakes before applying body coating. When installing them on a car that has been coated, remove the coating from the area where double- sided tape is to be applied before installation.
4. During the installation work, pay careful attention not to damage the car with tools, etc.
5. This manual describes how to install the product on the left side. Installation on the right side is symmetrical to that on the left side. Check the shape o f the components to be installed before carrying out the work.
6. When the air temperature is 15 °C or lower, use a hair dryer to warm up this product and the car surface where double-sided tape is to be applied to approx. 30°C to 50°C.
Avoid using an industrial dryer.
7. Double-sided tape does not adhere unless it is adequately pressed. The adhesive strength of double-sided tape significantly decreases when the tape is reapplied. Position the tape properly before applying it to avoid the need for reapplication.
8. The adhesive strength of the double-sided tape gradually increases after it is applied.
Avoid washing the car within 24 hours after installation. If the car needs to be washed or waxed on the day of the installation, leave it for at least one hour and use tape, etc. to cover the areas where double-sided tape is applied. Also be careful not to apply excessive force to the side strakes.
9. When blowing air after installing the product, keep the discharge port at least 300 mm away. If it is too close, it may cause the product to peel.
10. When a car has undergone a body coating treatment including glass coating, this product cannot exhibit its original adhesive performance.
Please confirm whether or not a body coating treatment is app lied to the car.
Moreover, ensure to remove dirt, oils and fats, etc. adhering to the surface on which the product is to be attached, and also use sufficient pressure to attach it to the car.
<<How to remove a body coating film and confirm the removal>>
– Use a fine-grained compound agent (so as not to affect the ca r’s paint) to rub the coating film off the area on which the product is to be attached.
– After polishing the area, spray water on it. You can confirm that the coating film has been removed when there is no repelling of water on the area.
Installation guidelines
This drawing shows how to install the product on the LH side.
1. Preparation work
Park the car on a level surface and securely apply the parking brake to ensure safe and reliable work.
（1）Remove the car clip from part A. [Fig.1]
Caution
The removed car clip will not be used.
（2）Position the Strake Kit – Side.
As shown in cross section A-A, apply three pieces of masking tape and align their bottom edges 1mm below the radius curve end of the side spoiler. [Fig.2]
Attach clip (small with a cross head) ③ to part A to fix the Strake Kit – Side.
Temporarily place the Strake Kit – Side to align its top edge with the bottom edge of the three pieces of masking tape, and then apply masking tape along the diagonal edge as shown in B. [Fig.2]
Check for any significant misalignment or interference between the side spoiler and the Strake Kit – Side.
Remove the Strake Kit – Side and the clip ③.
Caution
The removed clip (small with a cross head) will be reused.
Use a neutral detergent (or cleaning detergent) and waste cloth to remove any dirt adhering to the car’s surface where the Strake Kit – Side will be attached, and then dry the surface thoroughly.
Moreover, if sand or mud adheres to the back of the clip insertion holes, etc., then clean the contaminated sections.
（3）Partly peel off the liners of the double-sided tape on the back of the Strake Kit – Side and temporarily fix them to the surface of the Strake Kit – Side with masking tape. [Fig.3]
2. Installation work
（1）Align the edges of the Strake Kit – Side with the edges of the masking tape applied to the side spoiler during the preparation work and temporarily attach the Strake Kit -Side.
（2）Attach resin clip (small with a cross head) ③ to part A. [Fig.4]
（3）Peel off the liners of the double-sided tape in the direction of the arrow in order from “a” to “e” and attach the Strake Kit – Side by applying pressure with a force of 49 N or more. [Fig.4]
Caution
To avoid leaving any gaps between the contact surfaces of the Strake Kit – Side and the side spoiler, carry out the work while ensuring a good fit between them.
The liners of the double-sided tape may break when peeled off; therefore, pay careful attention when carrying out the work.
（4）After the work is completed, peel off the masking tape from the car.
If the surface of the guard or car is soiled, then wipe it clean.
Install the product on the right side in a similar manner.
This completes the installation work.
Inspection guidelines
Check the clip engagement and the bonded state of the double-sided tape and there shall be no rattling. There shall be no significant gap or separation.
E2610VC500
2022MY WRX Strake Kit – Side
Loading...
Reload document 
Open in new tab
| “This site contains affiliate links for which OEMDTC may be compensated” |
- Fitment: Compatile With 2002-2007 Subaru
Impreza WRX/Sti Models - Package Includes: A Set of Front and Rear Side Skirt Add-On Strake Guards as Shown (Total 4 Pieces)
- Comes In As A Set For Both Front and Rear
- Made of Quality and Durable Polyurethane Material
- Improves Appearance and Gives the JDM Look To Your WRX/Sti.
- Compatible with 2022-2025 Subaru BRZ Coupe 2-Door
- Material: Front Lip& Diffuser: PU - Polyurethane, Side Strakes: PP - Polypropylene | Color: Unpainted Black
- Package Includes: 1x Front Bumper Lip, 1x Rear Bumper Diffuser, 1x Set of Side Strakes (2 Pieces)
- Bolt-on Installation, Instructions NOT included, Professional Installation is Highly Recommended.
- 30 Days Limited Warranty
- FITMENT - Our side skirts are compatible with 2015-2021 Subaru WRX Sedan 4-Door; compatible with 2015-2021 Subaru WRX STI Sedan 4-Door. Please confirm your car model before purchasing to avoid that the purchased product is not suitable for your car
- PREMIUM MATERIAL - Durable high quality ABS plastic provides strong durability and long-lasting lifespan, has a good temperature resistance, impact resistant and weathering resistance. Carbon fiber printing finish gives your vehicle an attractive upgrade of appearance
- ADDITIONAL PROTECTION - Side skirt spoilers are installed along the sides of the car to stop rocks and debris from flying up from underneath and damaging the car's surface, thus protecting your car's paintwork
- AERODYNAMIC PERFORMANCE - Side skirts do not just streamline the sides of your car, they also help prevent airflow from the sides of the vehicle into the underside of the chassis, damaging the low-pressure front. Make your drive smoother, faster and safer
- PACKAGE & INSTALLATION - No Instructions. 1 Pair of Side Skirts (Carbon Fiber Color). Bolt on design for mounting, necessary installation hardware is included, installation can be done easily
- Custom Fitment: Compatible with 2022-2025 Subaru BRZ & Toyota GR86 Coupe 2-Door
- Specification: Material: ABS Plastic: Acrylonitrile Butadiene Styrene | Color: Unpainted Black | Style: STI Style | Package Include: 1x Set of Side Strakes (2 Pieces)
- Fashion Design: Unpainted Black side skirts extension splitter features a newly designed unique ground effects body kit, perfectly enhance the sporty racing look. It add an extra level of customized styling but will not lower the side height of the car
- Excellent Performance: Install a side rocker panel can offer great protection from side body scratch. It help reduce side air drag and keep stability at high speed, providing you with a comfortable and safe driving experience.
- Easy Installation: Comes with all necessary mounting hardwares. Since it is aftermarket auto part, installation instruction is not included. If you find it is difficult to install, professional installation is recommend.
- Fitment: Fits 2022-2023 Subaru BRZ / 2022-2023 Toyota GR 86
- Package Includes : 1 Pair of Carbon Fiber Side Add-On Spats Aprons (Both Left and Right Sides)
- STI Style Real Carbon Fiber Side Skirt Aero Guards Strake At Decent Price.
- Great Fitment And Quality.
- Made of Light Weight & Top-Grade Durable Carbon Fiber Material
- Package includes:1 set of Front Bumper Lip Chin Spoiler Guard Body Kits (3pcs) + Side Skirt Splitter (2pcs) + Rear Bumper Lip Wrap Splitter Canard (2pcs)
- Material:Made of updated durable and sturdy ABS, no deformation in long-term use,waterproof and never fade.
- Function:Provide an elegant and personalized appearance, provide anti-collision protective experience to your original bumper, protect from scrapes from driveways, speed bumps and curbs, alleviate the damage
- Compatibility:Perfect compatible with Subaru BRZ Impreza WRX STI,It won't scrape the paint off or damage the original equipment. Enjoy the super cool and exquisite appearance of your car after installing.
- Note:1.Please measure the position you are going to install the package, and make sure these splitters will fit your vehicle before purchase 2.Professional installation is highly recommended 3.Product may require drilling holes and use the screws to permanently secure.
- FITMENT - Our Side Skirts are compatible with 2012-2021 Subaru BRZ; compatible with 2012-2021 Toyota 86; compatible with 2012-2021 Scion FR-S. Please make sure that if your car is compatible with our products.
- IMPROVED AERODYNAMICS - Side skirts reduce the body's ground clearance above the road, creating less air pressure under the car, improving road-holding and allowing the car to be driven safely at higher speeds.
- ENHANCE APPEARANCE - The side skirts are also a design element that adds to the sporty feel of the car's design and enhances its visual appeal. Made from ABS for strength and durability.
- ADDITIONAL PROTECTION - The side skirts are fitted to the sides of the car to provide a degree of protection against the splashing of stones and debris from the road, which can scratch the surface of your car.
- INSTALLATION & PACKAGE INCLUDED - Screws help hold it in place and 3M tape makes it more securely mounted on your car. You will receive 1 Pair of side skirts and mounting hardware. No instructions.
- Product Compatibility: The side skirts are specifically designed to seamlessly compatible with 2015-2021 Subaru WRX Sedan/STI Sedan 4-Door, ensuring a direct fit and enhancing the overall aesthetics of the vehicle.
- Durable Construction: Made from high-quality ABS plastic, these side skirts are built to withstand the rigors of daily driving and provide long-lasting durability.
- Stylish Design: Featuring a sleek and sporty appearance, the side skirts add a touch of style and aggression to the vehicle's profile. Also provide additional protection against road debris, such as rocks, dirt, and grime.
- Enhanced Aerodynamics: These side skirts effectively redirect airflow around the car, reducing drag and increasing stability at higher speeds. The streamlined design helps to enhance fuel efficiency and performance.
- Easy Installation: No instruction. With a bolt-on installation process, these body kits can be easily mounted onto the vehicle without the need for extensive modifications. Including 1 pair of black side skirts and mounting hardware.
- Fitment: For Sub*aru 2015-2021 WRX Sedan 4-Door, For Sub*aru 2015-2021 WRX STI Sedan 4-Door
- Exceptional ABS Quality: Stand out from the crowd with our exceptional side skirts body kit, crafted from premium ABS plastic that ensures both durability and style.
- Toughness Meets Style: Combining rugged toughness with sleek styling, our side skirts body kit not only protects your car but also enhances its visual appeal.
- Vehicle-Specific Fit: Engineered to fit your specific vehicle model, our side skirts body kit ensures a perfect match, both in terms of functionality and aesthetics.
- Comprehensive Protection: Protect your car's sides from scratches, dents, and other road hazards with our abrasion-resistant ABS material, keeping your ride looking fresh and new.
- Quality & Fitment – Fits 2022-2025 Subaru BRZ & Toyota GR86 Coupe 2-Door. All of our products go through a rigorous quality control inspection and are test fitted to assure you that you are getting a quality product that fits your vehicle.
- Improved Design – Updated design to help provide a sleek profile look.
- Durability – Made out of high grade reinforced material and are designed to withstand harsh weather conditions.
- Easy Install – All necessary hardware required for installation are included.
- Service - We've been researched and developed automotive parts for years. Providing you an enjoyable shopping experience is our top priority. Please place your order without worries.
Last update on 2025-04-17 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.
SEOCONTENT-START
１ 00 ① ③ ④ ② Part Description Strake Kit – Side RH Strake Kit – Side LH Quantity 1 1 Ｎｏ. ① ② Part Description Resin clip（small with a cross head） LABEL Quantity 2 1 Ｎｏ. ③ ④ Genuine Part Number：E2610VC500 Applicable Model： WRX 2022MY～ Waste cloth, neutral detergent or cleaning detergent [IPA (isopropyl alcohol) or nonane], masking tape, clip remover, flathead screwdriver, Phillips screwdriver ※The completed drawing shows the left side of the car. Installation Manual Strake Kit – Side Distributor Components Tools Co., Ltd. E 2610VC 518 Strake Kit – Side FITTING KIT Completed installation drawing Front side of the car Strake Kit – Side Repair part model number FITTING KIT（E2610VC518）：③×2／④×1 ２ Starake Kit – Side This manual describes how to install the side strakes. Request Before installing this product, please ensure to read this manual and carry out proper installation. ！ Precautions 1. When installing this product, park the car on a level surface and securely apply the parking brake before carrying out the work. 2. Before the installation, use a neutral detergent (or cleaning detergent) and waste cloth to remove any dirt adhering to the car’s surface where the side strakes will be attached, and then dry the surface thoroughly. Moreover, if sand or mud adheres to the back of the clip insertion holes, etc., then clean the contaminated sections. 3. Install the side strakes before applying body coating. When installing them on a car that has been coated, remove the coating from the area where double-sided tape is to be applied before installation. 4. During the installation work, pay careful attention not to damage the car with tools, etc. 5. This manual describes how to install the product on the left side.Installation on the right side is symmetrical to that on the left side. Check the shape of the components to be installed before carrying out the work. 6. When the air temperature is 15°C or lower, use a hair dryer to warm up this product and the car surface where double-sided tape is to be applied to approx. 30°C to 50°C. Avoid using an industrial dryer. 7. Double-sided tape does not adhere unless it is adequately pressed. The adhesive strength of double-sided tape significantly decreases when the tape is reapplied.Position the tape properly before applying it to avoid the need for reapplication. 8. The adhesive strength of the double-sided tape gradually increases after it is applied. Avoid washing the car within 24 hours after installation. If the car needs to be washed or waxed on the day of the installation, leave it for at least one hour and use tape, etc. to cover the areas where double-sided tape is applied. Also be careful not to apply excessive force to the side strakes. 9. When blowing air after installing the product, keep the discharge port at least 300 mm away. If it is too close, it may cause the product to peel. 10. When a car has undergone a body coating treatment including glass coating, this product cannot exhibit its original adhesive performance. Please confirm whether or not a body coating treatment is applied to the car. Moreover, ensure to remove dirt, oils and fats, etc. adhering to the surface on which the product is to be attached, and also use sufficient pressure to attach it to the car. <<How to remove a body coating film and confirm the removal>> – Use a fine-grained compound agent (so as not to affect the car’s paint) to rub the coating film off the area on which the product is to be attached. – After polishing the area, spray water on it. You can confirm that the coating film has been removed when there is no repelling of water on the area. 3 【Fig.1】 【Fig.2】 【Fig.3】 （3）Partly peel off the liners of the double-sided tape on the back of the Strake Kit – Side and temporarily fix them to the surface of the Strake Kit – Side with masking tape. [Fig.3] （2）Position the Strake Kit – Side. As shown in cross section A-A, apply three pieces of masking tape and align their bottom edges 1mm below the radius curve end of the side spoiler. [Fig.2] Attach clip (small with a cross head) ③ to part A to fix the Strake Kit – Side. Temporarily place the Strake Kit – Side to align its top edge with the bottom edge of the three pieces of masking tape, and then apply masking tape along the diagonal edge as shown in B. [Fig.2] Check for any significant misalignment or interference between the side spoiler and the Strake Kit – Side. Remove the Strake Kit – Side and the clip ③. Use a neutral detergent (or cleaning detergent) and waste cloth to remove any dirt adhering to the car’s surface where the Strake Kit – Side will be attached, and then dry the surface thoroughly. Moreover, if sand or mud adheres to the back of the clip insertion holes, etc., then clean the contaminated sections. The removed clip (small with a cross head) will be reused. A Masking tape Strake Kit – Side Radius curve end Side spoiler Cross section A－A 1mm A A B Masking tape Masking tape A ③ 1. Preparation work Park the car on a level surface and securely apply the parking brake to ensure safe and reliable work. Installation guidelines This drawing shows how to install the product on the LH side. （1）Remove the car clip from part A. [Fig.1] The removed car clip will not be used. Caution Caution 4 【Fig.4】 After the work is completed, peel off the masking tape from the car. If the surface of the guard or car is soiled, then wipe it clean. Install the product on the right side in a similar manner. This completes the installation work. （4） To avoid leaving any gaps between the contact surfaces of the Strake Kit – Side and the side spoiler, carry out the work while ensuring a good fit between them. The liners of the double-sided tape may break when peeled off; therefore, pay careful attention when carrying out the work. 2. Installation work Align the edges of the Strake Kit – Side with the edges of the masking tape applied to the side spoiler during the preparation work and temporarily attach the Strake Kit -Side. Attach resin clip (small with a cross head) ③ to part A. [Fig.4] Peel off the liners of the double-sided tape in the direction of the arrow in order from “a” to “e” and attach the Strake Kit – Side by applying pressure with a force of 49 N or more. [Fig.4] （1） （2） （3） Crimping A e d c b a ③ Crimping Crimping Crimping Crimping Revised contents △ Details of the work date 00 Newly created document 2021.06.09 Caution Check the clip engagement and the bonded state of the double-sided tape and there shall be no rattling. There shall be no significant gap or separation. Inspection guidelines
**************************************************************************************************************
SEOCONTENT-END
