| “This site contains affiliate links for which OEMDTC may be compensated” |
NHTSA ID Number: 10232511
Manufacturer Communication Number: 095513
Summary
Fuel Tank Insulation Pad / Fuel Delivery Tube Changes
NUMBER: 09-55-13
DATE: 06/19/13
| APPLICABILITY: | 2014MY Forester |
|---|---|
| SUBJECT: | Fuel Tank Insulation Pad / Fuel Delivery Tube Changes |
INTRODUCTION
This Bulletin informs of changes to both the padding on the fuel tank assembly and the cushions found on the fuel delivery tubing connecting the main fuel pump assembly to the sub-level unit (transfer pump).
COUNTERMEASURE IN PRODUCTION
The new parts were incorporated into production starting with VIN E*412069.
PART INFORMATION
| PART NAME | NEW PART NUMBER | NOTES | OLD PART NUMBER | NOTES |
|---|---|---|---|---|
| Tube Delivery | 42074SG011 | 3 Pieces of Tube Cushion | 42074SG010 | 1 Piece of Tube Cushion |
| Tube Delivery Sub | 42074SG021 | 3 Pieces of Tube Cushion | 42074SG020 | 2 Pieces of Tube Cushion |
| SEAT TANK B
(Insulation Pads) | n/a | See Note Below | 42016CA010 | See Note Below |
NOTE: Part interchangeability is from NEW to OLD only
SERVICE PROCEDURE / INFORMATION
Follow the procedures in the applicable Service Manual for fuel tank and delivery tubing R&R.
- When replacing the fuel tank and reusing the original fuel delivery tubes on the new tank, 2
pieces of insulation pad (SEAT TANK B) must be installed onto the new tank to prevent the fuel delivery tubes from contacting it. Peel the paper backing to expose the adhesive then apply to the new tank as shown in the illustration below.
NOTE: Before applying the new insulation pads, make sure that area of the tank is clean and dry.
- When replacing only the fuel delivery tubes, the existing SEAT TANK B (insulation pad) material can remain in place on the original fuel tank.
- When replacing both the fuel tank AND the fuel delivery tubes, SEAT TANK B (insulation pad) does NOT need to be installed onto the new tank due to the additional tube cushions included with the new tubes.
Installation Locations for Installation of SEAT TANK B (insulation pad) Material
1 Affected Product
Vehicle
| MAKE | MODEL | YEAR |
SUBARU | FORESTER | 2014 |
1 Associated Document
Manufacturer Communications
NUMBER: 09-55-13
DATE: 06/19/13
MC-10232511-9999.pdf 627.276KB
Loading...
Reload document 
Open in new tab
NHTSA ID Number: 10052497
Manufacturer Communication Number: TSB-09-55-13
Summary
SUBARU: THERE ARE CHANGES TO THE FUEL TAMK ASSEMBLY AND THE CUSHIONS FOUND ON THE FUEL DELIVERY TUBE. *JS
1 Associated Document
Service Bulletin Document
NUMBER: 09-55-13
DATE: 06/19/13
SB-10052497-3814.pdf 440.679KB
Loading...
| “This site contains affiliate links for which OEMDTC may be compensated” |
- The world’s #1 fuel additive for both gasoline and diesel engines
- A great tune-up in a bottle – treats gasoline, diesel fuel and increases MPG
- Cleans and lubricates the fuel system, including fuel injectors, carburetor and combustion chamber
- Improves fuel economy by burning excess exhaust emissions
- Increases power and acceleration by improving fuel flow and reducing deposit buildup
- Restores fuel economy
- Stabilizes ethanol
- Maximizes horsepower
- Improves responsiveness
- For use in both gasoline and diesel engines
- Cleans, restores, protects the entire fuel system (fuel injectors, carburetors, intake valves and combustion chambers)
- Restores: lost power, acceleration, lost fuel economy, and operation of the fuel gauge sensor
- Reduces: rough idle, engine surge, hesitation, and spark plug fouling
- Improves: cold start performance, and fuel stability for up to one year
- Automobiles and trucks use every 3,000 miles or at your next oil change. All other gasoline engines use as needed (motorcycles, dirt bikes, boats, ATVs, RVs, water craft, lawn care, etc.)
- Contains 100% High-Energy Solvent Technology
- Helps Keep Injectors Or Carb(S) And Intake Ports And Valves Clean
- Quickly Disperses Moisture And Dissolves Gum, Varnish, And Other Fuel Residues
- Disperses Moisture In Conventional Gasoline
- Specially formulated to remove carbon deposits from engines with over 75,000 miles
- Cleans fuel injectors, intake valves, and ports to restore performance and fuel economy
- Prevents future carbon build-up and reduces emissions
- Oxygen sensor safe and safe for use in turbocharged and supercharged vehicles
- Will not void OEM/manufacturer's warranty
- Eliminates starting problems, hesitation and stalling.Fit Type: Universal
- Smoother idling
- Better throttle response
- Cleaner combustion
- Unclogs dirty fuel injectors to restore performance
- Helps restore lost power and acceleration
- Removes harmful deposits
- Compatible with cap-less gas systems
- Saves gas
- Upgraded Universal Fuel Injector Tester and Cleaner Tool Kit---Operates injectors individually to diagnose fuel delivery problems on petrol vehicles with electronic fuel injection, such as blockage, leakage, damage, and burnout of the injectors. The included 8-size cleaning adapters combined with the tester pulse mode can quickly clean the injectors
- 【Test for 2 Injectors Simultaneously & Ultra-long Power Cord】Come with two pairs of output terminals, allowing you to test for two injectors or for one injector at once. The tester power cord is up to 40inch and the test lead is up to 20 inches for convenient testing. The wires are made of superior silica gel, allowing the tester to work at high and low temperatures. （To make it perform better, it is recommended to work at normal temperatures.）
- 【8 Size Adapters Cleaning Tool & Universal Fit】Our cleaner small and large size adapters are compatible with most 12V EFI and GDI vehicle models' injectors. We also offer two additional specialized adapters for the BMW Audi, one is suitable for models such as V.W, Audi, etc. and another one with threaded hole is exclusively for BMW N series such as N14/N18/N20/N26/N53/N54/N55/N63/S63.
- 【8 Pulse Modes & LCD Display】The fuel injector tester kit is designed with 8 pulse modes, which are composed of 4 pulse signal output modes and 2 output voltage levels: Short/ Medium/ Long/ Continuous pulse modes + High/Low(12V/5V) power drive modes. This tester has a wide variety of pulse modes, providing a large testing space to accurately and quickly diagnose and repair petrol vehicle injectors' fuel delivery problems. The LCD displays the mode you are in.
- 【Polarity Reverse Connection Protection & Short Circuit Protection】Deigned with power input reverse connection protection and output short circuit protection function. In the case damaged or a short circuit of the pulse output terminal, the power indicator light of the fuel injector cleaner tool kit will flash to prompt you.
- DESIGNED TO EXCEED EXPECTATIONS: Red Line complete SI-1 fuel system cleaner treatment for cleaning and preventing corrosion in fuel systems
- PERFORM AND PROTECT: Fuel additive cleans injectors, carburetors, valve and combustion chamber deposits with a powerful, concentrated blend of high-temp and low-temp detergents
- EFFICIENT FUEL BURN: Gas treatment that enhances gasoline stability, while reducing the build up of gum and varnish formation
- EASY TO USE: Use one bottle per tank for most effective treatment, additive cleans nearly 100% efficiency in one treatment
- One 15 Ounce Bottle
Last update on 2025-04-15 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.
SEOCONTENT-START
Bulletin Number: 09-55-13; Date: 06/19/13 Page 1 INTRODUCTION This Bulletin informs of changes to both the padding on the fuel tank assembly and the cushions found on the fuel delivery tubing connecting the main fuel pump assembly to the sub-level unit (transfer pump). COUNTERMEASURE IN PRODUCTION The new parts were incorporated into production starting with VIN E*412069. PART INFORMATION PART NAME NEW PART NUMBER NOTES OLD PART NUMBER NOTES Tube Delivery 42074SG011 3 Pieces of Tube Cushion 42074SG010 1 Piece of Tube Cushion Tube Delivery Sub 42074SG021 3 Pieces of Tube Cushion 42074SG020 2 Pieces of Tube Cushion SEAT TANK B (Insulation Pads) n/a See Note Below 42016CA010 See Note Below NOTE: Part interchangeability is from NEW to OLD only SERVICE PROCEDURE / INFORMATION NUMBER: 09-55-13 DATE: 06/19/13 APPLICABILITY: 2014MY Forester SUBJECT: Fuel Tank Insulation Pad / Fuel Delivery Tube Changes SERVICE BULLETIN ATTENTION: GENERAL MANAGER q PARTS MANAGER q CLAIMS PERSONNEL q SERVICE MANAGER q IMPORTANT – All Service Personnel Should Read and Initial in the boxes provided, right. Continued… CAUTION: VEHICLE SERVICING PERFORMED BY UNTRAINED PERSONS COULD RESULT IN SERIOUS INJURY TO THOSE PERSONS OR TO OTHERS. Subaru Service Bulletins are intended for use by professional technicians ONLY. They are written to inform those technicians of conditions that may occur in some vehicles, or to provide information that could assist in the proper servicing of the vehicle. Properly trained technicians have the equipment, tools, safety instructions, and know-how to do the job correctly and safely. If a condition is described, DO NOT assume that this Service Bulletin applies to your vehicle, or that your vehicle will have that condition. SUBARU OF AMERICA, INC. IS “ISO 14001 COMPLIANT” The international standard for excellence in Environmental Management Systems. Please recycle or dispose of automotive products in a manner that is friendly to our environment and in accordance with all local, state and federal laws and regulations. OLD NEW FUEL DELIVERY TUBE 42074SG010/020 42074SG011/021 SEAT TANK B (Insulation Pads) 42016CA010 Tube Cushions Additional Tube Cushions Bulletin Number: 09-55-13; Date: 06/19/13 Page 2 Follow the procedures in the applicable Service Manual for fuel tank and delivery tubing R&R. • When replacing the fuel tank and reusing the original fuel delivery tubes on the new tank, 2 pieces of insulation pad (SEAT TANK B) must be installed onto the new tank to prevent the fuel delivery tubes from contacting it. Peel the paper backing to expose the adhesive then apply to the new tank as shown in the illustration below. NOTE: Before applying the new insulation pads, make sure that area of the tank is clean and dry. • When replacing only the fuel delivery tubes, the existing SEAT TANK B (insulation pad) material can remain in place on the original fuel tank. • When replacing both the fuel tank AND the fuel delivery tubes, SEAT TANK B (insulation pad) does NOT need to be installed onto the new tank due to the additional tube cushions included with the new tubes. Installation Locations for Installation of SEAT TANK B (insulation pad) Material 39 +/- 15mm More than 270mm SEAT TANK B (insulation pad) Tube Cushions (Old Part Number Shown)
SEOCONTENT-END
